Cat. No. 43-778
OWNER’S MANUAL
Please read before using this equipment.
TAD-1018
Single Microcassette
Answering System with Trim-Style Phone
We recommend you record your sys-
tem’s serial number here. The number
is on the bottom of the answering sys-
tem.
READ THIS FIRST
We have designed your system to
conform to federal regulations, and
you can connect it to most telephone
lines. However, each device you con-
nect to the phone line draws power
from the phone line. We refer to this
power draw as the device’s ringer
equivalence number, or REN. The
REN is on the bottom of your answer-
ing system.
Serial Number:
This system has been tested and
found to comply with all applicable UL
and FCC standards.
WARNING: To reduce the risk of
fire or shock hazard, do not ex-
pose this product to rain or mois-
ture.
If you are using more than one device
on the line, add up all the RENs. If the
total is more than five, your phones
might not ring and your answering
system might not answer. In rural ar-
eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
telephone line.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
FCC STATEMENT
Your answering system complies with
Part 68 of FCC Rules. You must, upon
request, provide the FCC registration
number and the REN to your phone
company. Both numbers are on the
bottom of your answering system.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
Note: You must not connect your an-
swering system to:
!
cluded in the literature accompany-
ing this product.
• Coin-operated systems
• Party-line systems
• Most electronic key phone sys-
tems
3
CONTENTS
Installation ............................................................................................................ 5
Selecting a Location ........................................................................................ 5
Loading the Cassette ....................................................................................... 5
Connecting Power ........................................................................................... 6
Recording the Outgoing Message ................................................................... 6
Checking the Outgoing Message .............................................................. 7
Placing the Phone on a Desk Top ................................................................... 8
Mounting the Phone on the Wall ..................................................................... 8
Turning Off/On the Ringer ............................................................................. 10
Setting the Number of Rings ......................................................................... 10
Setting the Dialing Mode ............................................................................... 10
Telephone Operation ......................................................................................... 12
Using Pause .................................................................................................. 12
Using REDIAL ............................................................................................... 12
Using FLASH ................................................................................................. 12
Setting the Phone’s Volume .......................................................................... 13
Using Tone Services with a Pulse Line .......................................................... 13
Answering System Operation ........................................................................... 14
Setting the Answering System to Answer Calls ............................................. 14
Setting the Recording Time ........................................................................... 14
Setting the Answering System’s Volume ....................................................... 14
Screening Calls ............................................................................................. 15
Playing Messages ......................................................................................... 15
Remote Control Operation ................................................................................ 17
Remote Playback .......................................................................................... 17
Erasing the Messages ................................................................................... 17
Remote Answer-On ....................................................................................... 18
Troubleshooting ................................................................................................. 19
Care and Maintenance ....................................................................................... 21
Cleaning the Tape-Handling Parts ................................................................. 22
The FCC Wants You to Know ........................................................................ 22
Lightning ........................................................................................................ 22
4
INSTALLATION
1. Turn the supplied cassette’s hub
with the tip of a pencil to take up
any tape slack.
SELECTING A
LOCATION
You can set the TAD-1018 on a flat
surface (such as a desk top or counter
top), or mount it on a wall plate or di-
rectly on the wall.
Select a location that is:
• Near an AC outlet
2. Lift open the cassette compart-
ment door.
• Near a modular phone line jack
If the phone line jack is not a modular
jack, you must update the wiring. You
can convert the wiring yourself, using
jacks and adapters available at your
local RadioShack store. Or, you can
let the phone company update the wir-
ing for you.
Note: The USOC number of the jack
to be installed is RJ11C.
3. Put the cassette in the compart-
ment with its full reel toward the
back of the answering system and
its open edge to the right.
LOADING THE
CASSETTE
Your answering system comes with an
MC-60 cassette tape (30 minutes of
recording time per side). You can buy
additional and different length cas-
settes at your local RadioShack store.
4. Close the compartment door.
5
Notes:
• You can turn the tape over and
The MESSAGE indicator lights while
the answering system checks for an
outgoing message.
record on the other side. This lets
you save any messages recorded
on the first side while using the
tape to record more messages.
If an outgoing message is already re-
corded, the answering system auto-
matically plays it back. If there is no
outgoing message, the answering
system sounds a continuous tone until
you record a message (see “Record-
ing the Outgoing Message”).
• Replace the tape at least once a
year, or more often if it is used fre-
quently.
Note: If the cassette tape is broken or
is not inserted properly and the an-
swering system has power, the sys-
tem sounds a continuous tone. To
stop the tone, unplug the adapter from
the AC outlet. Reinsert or replace the
cassette tape, then plug the adapter
back into the AC outlet.
CONNECTING POWER
Use the supplied AC adapter to power
your answering system.
Cautions:
• Use only the supplied adapter.
• Always plug the adapter into the
answering system before you plug
it into an AC outlet. Always unplug
the adapter from the AC outlet be-
fore you unplug it from the an-
swering system.
RECORDING THE
OUTGOING MESSAGE
Before you can set the answering sys-
tem to answer calls and record mes-
sages, you must record the message
the caller hears when the answering
system answers a call.
Follow these steps to connect the
TAD-1018 to power.
In the message, ask for the caller’s
name, phone number, and message.
The maximum length for your outgo-
ing message is 30 seconds.
1. Plug the AC adapter’s barrel plug
into the answering system’s
Important Hint: Do not tell callers that
you are not home. Instead, say that
you cannot come to the phone right
now.
POWER SOURCE
jack.
2. Plug the other end of the adapter
into a standard AC outlet.
6
Follow these steps to record your out-
going message.
5. When you finish recording your
message, press OGM REC/PLAY
again. The MESSAGE indicator
turns off, then the answering sys-
tem beeps twice and plays back
the message as it is recording
from the digital chip to the tape.
(The message is backed up on
tape so after a power failure it can
be automatically restored to the
chip.)
1. Rotate VOLUME on the base to
the right until it clicks. The MES-
SAGE indicator lights.
Wait until the answering system plays
back the message before you contin-
ue installing your answering system.
2. Lift open the cassette compart-
ment door.
3. Hold down OGM REC/PLAY until
the MESSAGE indicator turns off,
then release the button. The
answering system beeps once.
Checking the Outgoing
Message
Press OGM REC/PLAY at any time to
hear the outgoing message. The an-
swering system beeps once, plays
back the message, beeps twice, then
resets to answer calls.
To adjust the volume, rotate VOLUME.
4. When the MESSAGE indicator
lights again, speak clearly in a
normal voice about 12 inches
away from the microphone.
Microphone
7
1. Pull the handset holder toward
you as far as it will go. Hold it out
as you rotate the holder 180°,
then let it snap back in place.
PLACING THE PHONE
ON A DESK TOP
To use your answering system on a
desk, table, or shelf, plug the tele-
phone cord into a modular phone jack.
Plug one end of the coiled handset
cord into the handset jack on the an-
swering system and the other end into
the jack on the handset. Place the
handset on the cradle.
The holder’s tab holds the hand-
set in the cradle while the answer-
ing system is mounted on the wall.
2. To mount the TAD-1018 directly
onto the wall, drill two holes 31/4
inches apart, one above the other,
at the desired location.
MOUNTING THE PHONE
ON THE WALL
Using the supplied mounting bracket,
you can mount the TAD-1018 on a
phone jack wall plate or directly on the
wall.
If you are mounting the phone directly
on the wall, you need two screws with
heads that fit into the bracket’s key-
hole slots.
8
3. Thread a screw
into each hole
until it’s head
1
extends about /8
inch from the
wall.
1
”
/8
4. If you are mounting the system on
a wall plate, thread the telephone
cord into the left slot on the top of
the mounting bracket and pull it
through the large hole in the cen-
ter of the bracket. If you mounting
the system directly on the wall,
thread the telephone cord into the
left slot on the top and bottom of
the mounting bracket.
6. When mounting on a wall plate,
coil all the excess telephone cord
into the mounting bracket’s recess
by pushing it back through the
large hole. Leave only about 1–2
inches of the cord outside the
bracket.
7. Plug the telephone cord into the
wall plate or a modular phone
jack.
Thread the adapter’s power cord
into the right slot on the top and
bottom of the mounting bracket.
5. Insert the mounting bracket’s tabs
into the slots on the bottom of the
answering system. Then push the
bracket up until it snaps into
place.
8. Line up the keyhole slots on the
bracket with the studs on the wall
plate (or with the screws in the
wall), then slide the bracket down
until it is secure.
9
9. Plug one end of
the coiled hand-
set cord into the
handset jack on
the
answering
system and the
other end into the
jack on the hand-
set. Place the
handset in the
cradle.
The system answers calls in 2, 4, or 7
TS
rings, or if you set the switch to
(Toll Saver — the last position), the
answering system answers in 4 rings
if no messages are saved or in 2 rings
if you have messages. Toll Saver can
save you long-distance charges be-
cause, if there are no new messages,
you can hang up before the answering
system answers.
TURNING OFF/ON THE
RINGER
To turn off the telephone’s ringer, set
RINGER
OFF
. You can still make
to
outgoing calls. If you hear an exten-
sion phone ring, you can still answer
calls.
SETTING THE DIALING
MODE
TONE/
Pick up the handset, then set
PULSE
for the type of service you
have.
When you want the telephone to ring
RINGER
ON
.
again, set
to
SETTING THE NUMBER
OF RINGS
If you are not sure which type you
have, do this test.
You can select the number of rings the
answering system waits before it an-
1. Pick up the handset and listen for
a dial tone.
RING SELECT
swers calls. Set
desired position.
to the
TONE/PULSE
TONE
.
2. Set
to
0
3. Press any number other than .
10
Note: If your phone system re-
quires that you dial an access
9
code ( , for example) before you
dial an outside number, do not
press the access code either.
If the dial tone stops, you have
TONE/
touch-tone service. Leave
PULSE TONE
set to
.
If the dial tone continues, you
TONE/
have pulse service. Set
PULSE PULSE
to
.
Notes:
#
TONE/
•
does not function when
PULSE PULSE
is set to
.
• If you have pulse service and
want to use a special service that
requires tone signals (such as
bank-by-phone), see “Using Tone
Services with a Pulse Line” on
Page 13.
11
TELEPHONE OPERATION
You can make and answer calls with
this telephone as you would with any
other phone. Read this section to
learn about special features.
USING REDIAL
To quickly dial the last number dialed,
press REDIAL. The redial memory
stores up to 32 digits so you can
quickly redial local as well as long-
distance numbers.
USING PAUSE
In some telephone systems, you must
dial an access code (9, for example)
and wait for a second dial tone before
you can dial an outside number. You
can enter a pause after the access
code to allow the outside line time to
connect.
To enter a 4-second pause while dial-
ing a phone number, press PAUSE.
For a longer pause, press PAUSE ad-
ditional times.
USING FLASH
Many special phone services, such as
Call Waiting, require a switchhook sig-
nal. Pressing FLASH performs the
electronic equivalent of a switchhook
operation.
For example, if you subscribe to Call
Waiting, press FLASH to put your cur-
rent call on hold and answer an in-
coming call on the same line. Press
FLASH again to alternate between the
two calls.
12
Note: If you do not have any special
FLASH
might disconnect your current call.
USING TONE SERVICES
WITH A PULSE LINE
telephone services, pressing
Some special services, such as alter-
nate long-distance and bank-by-
phone, require tone signals. If you
have pulse service, you can still use
special services by following these
steps.
SETTING THE PHONE’S
VOLUME
VOL
Slide
(volume) on the handset to
set the handset’s volume to the de-
sired level.
TONE/PULSE
call the special service.
PULSE
,
1. With
set to
2. When the service answers, press
TONE
. Any additional numbers
you dial are sent as tone signals.
3. When you complete the call, hang
up the phone. The phone auto-
matically changes back to the
pulse mode.
13
ANSWERING SYSTEM OPERATION
hangs up. See “Remote Control Oper-
ation” on Page 17.
SETTING THE
ANSWERING SYSTEM
TO ANSWER CALLS
To have the answering system not an-
swer calls, rotate VOLUME to OFF. The
MESSAGE indicator turns off.
Rotate VOLUME on the base to the
right. When the MESSAGE indicator
stays on without the answering sys-
tem sounding a tone, the system is
ready to answer calls.
SETTING THE
RECORDING TIME
You can select the length of recording
time for incoming messages. Slide
REC TIME to 1 MIN to set the TAD to
record for up to 1 minute for each
message or to 5 MIN for up to 5 min-
utes.
The answering system records mes-
sages and hangs up and resets to an-
swer the next call when:
• The caller hangs up.
• The maximum message length of
about 1 minute or 5 minutes is
reached.
• There are more than 7 seconds of
silence.
SETTING THE
ANSWERING SYSTEM’S
VOLUME
The answering system can record up
to about 29 minutes of incoming mes-
sages on the supplied tape. If the tape
reaches the end while a caller is leav-
ing a message, the answering system
beeps twice and hangs up.
Adjusting the answering system’s
VOLUME control sets the speaker vol-
ume. (This does not affect the volume
of the message the caller hears.)
If the incoming message tape is full,
the answering system answers a call
after 10 rings, plays back the outgoing
message, then waits 7 seconds for the
remote operation security code. If the
correct code is not entered, the an-
swering system beeps twice and
14
SCREENING CALLS
To screen calls, let the answering sys-
tem answer them, then listen to the
caller’s message through the answer-
ing system’s speaker. If you decide to
answer the call, pick up any phone on
the same phone line as the answering
system (including the system’s
phone). The answering system stops
recording and resets to answer the
next call.
To pause playback for up to 60 sec-
PLAY
onds, press
. To restart play-
PLAY
back, press
again.
Note: If you pick up the phone just as
the answering system answers, the
answering system might not stop re-
cording the message. If this happens,
hang up the phone for a moment then
pick it up again.
Notes:
• If you do not restart playback
within 60 seconds, the tape fast-
forwards to the end of the last re-
corded message, as though play-
back was never started.
• If a call comes in while playback is
paused, the tape fast-forwards to
the end of the last recorded mes-
sage and then answers the call.
PLAYING MESSAGES
When you have messages, the MES-
SAGE indicator flashes. If you have
four messages or less, the light flash-
es once for each message stored.
(For example, if you have two mes-
sages, the light flashes twice, pauses,
then flashes twice more, and so on.) If
you have more than four messages,
the light flashes continuously.
VOLUME
OFF
during
• If you turn
to
playback, the system stops play-
back, the tape fast-forwards to the
end of the last recorded message,
and the MESSAGE indicator turns
off, as though playback was never
started. All messages are saved.
After you play back all the messages,
the answering system beeps twice
and resets to answer calls. New mes-
sages will be recorded over the mes-
sages you have heard.
PLAY
To play the messages, press
.
The answering system beeps, re-
winds, then plays the messages.
15
To save the messages, press SAVE
before a new call is recorded. The
tape fast-forwards to the end of all the
messages and resets to answer calls.
To replay the messages, simply press
PLAY again.
16
REMOTE CONTROL OPERATION
While you are away from your home
or office, you can use a touch-tone
phone or a pulse phone with a pocket
tone dialer to:
Note: If you do not enter the code
within 7 seconds, the answering sys-
tem hangs up.
The answering system plays back the
incoming messages. At the end of all
the messages, the answering system
sounds single beeps and tones then
four short beeps.
• Play your messages
• Erase your messages
• Set the answering system to an-
swer calls
Note: The answering system auto-
matically saves your messages after
remote playback.
REMOTE PLAYBACK
You must know your remote operation
security code to play back your mes-
sages from a remote phone. This
code (a 3-digit number) is on the bot-
tom of your answering system.
To replay the messages, wait about 8
seconds after the four short beeps.
When you hear a single beep, enter
the remote operation security code
again.
To play back your messages from a
remote phone, follow these steps.
ERASING THE
MESSAGES
1. Dial your phone number.
If RING SELECT is set to TS, the
answering system answers on the
second ring if there are mes-
sages. If there are no messages,
the answering system answers on
the fourth ring.
If you want to erase the messages af-
ter playback, enter the remote opera-
tion security code within 8 seconds
after the four short beeps at the end of
all the messages. After the answering
system beeps, hang up the phone.
2. After the outgoing message stops
and a beep sounds, enter the re-
mote operation security code
within 5 seconds. Be sure each
Note: After you erase messages by
remote, you cannot recover them
(even if you press SAVE as soon as
you get back to your answering sys-
tem).
1
button press is at least /2 second
long. The answering system
sounds a tone while the tape re-
winds. If no tone sounds, re-enter
the code.
17
REMOTE ANSWER-ON
You can use any remote phone to set
the answering system to answer calls
if:
• The answering system has power,
• The cassette is loaded, and
• The answering system is off.
To set the answering system to an-
swer calls, dial your phone number
and wait about 60 seconds until the
answering system answers. Then
hang up the phone.
Note: Be sure to turn on the system
when you get home, to play back any
recorded messages.
18
TROUBLESHOOTING
We do not expect you to have any problems with your answering system, but if you
do, be sure you installed the tape correctly. If you still have a problem, this chart
might help. If it does not, take the answering system to your local RadioShack store
for assistance.
Problem
Cause
Solution
The answering sys-
tem does not answer
and record callers’
messages.
The system is turned off.
Turn on the answering system
by rotating VOLUME to the
right.
The outgoing message is
not recorded.
Record an outgoing message.
Bad phone line connection. Check and reconnect the mod-
ular phone plugs.
Check to see if the phone
works properly.
Be sure you have electrical
power.
The answering sys-
tem records a dial
tone, beeping, or the
operator’s voice in-
stead of the caller’s
message.
The caller hung up without If this happens often, discuss
leaving a message or with- the problem with your phone
out using the maximum
time, and your phone com-
pany does not send out
CPC (Calling Party Control)
signals.
company.
The answering sys-
tem does not re-
spond to any button.
The answering system has Turn on the answering system
been turned on by remote. by rotating VOLUME to the
right.
The answering system is
locked up.
Reset the answering system by
unplugging the AC adapter
from the AC outlet, then plug-
ging it in again.
19
Problem
Cause
Solution
Recordings sound
distorted.
You were too close to the
microphone or you spoke
Record the message again.
Speak clearly into the micro-
too loudly when you record- phone in a normal voice about
ed the outgoing message.
12 inches away.
The tape head is dirty.
Clean the head using a tape
head-cleaning kit (see “Clean-
ing the Tape-Handling Parts”
on Page 22).
The tape is worn out.
Unplug the adapter from the
AC outlet, replace the tape,
then plug the adapter back into
the AC outlet.
Remote control func- The correct remote opera-
Enter the correct code.
tions do not work.
tion security code was not
entered.
You are using a pulse dial- Use a touch-tone phone or
ing phone.
pocket tone dialer.
The tone output from the
phone or tone dialer is not
long enough.
Press and hold the buttons for
1
2
at least / second or try using
another phone or dialer.
The telephone line is noisy. Enter the remote operation se-
curity code again.
Seven seconds of silence
have passed so the an-
swering system hangs up.
Call the answering system and
try again.
Continuous tone
sounds.
No outgoing message re-
corded.
Record an outgoing message
(see “Recording the Outgoing
Message” on Page 6).
The cassette tape is bro-
ken.
Unplug the adapter from the
AC outlet, replace the tape,
then plug the adapter back into
the AC outlet.
The cassette tape is
jammed.
Unplug the adapter from the
AC outlet; remove, unjam, and
reinstall the tape; then plug the
adapter back into the AC outlet.
20
CARE AND MAINTENANCE
Your RadioShack TAD-1018 Single Microcassette Answering System with Trim-
Style Phone is an example of superior design and craftsmanship. The following
suggestions will help you care for your answering system so you can enjoy it for
years.
Keep the answering system dry. If it gets wet, wipe it dry immediately.
Liquids might contain minerals that can corrode the electronic cir-
cuits.
Handle the answering system gently and carefully. Dropping it can
damage circuit boards and cases and can cause the answering sys-
tem to work improperly.
Use and store the answering system only in normal temperature en-
vironments. Temperature extremes can shorten the life of electronic
devices and distort or melt plastic parts.
Keep the answering system away from dust and dirt, which can
cause premature wear of parts.
Wipe the answering system with a damp cloth occasionally to keep it
looking new. Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the answering system.
Modifying or tampering with the answering system’s internal components can
cause a malfunction and might invalidate its warranty and void your FCC authoriza-
tion to operate it. If your answering system is not performing as it should, take it to
your local RadioShack store for assistance. If the trouble is affecting the phone
lines, the phone company can ask you to disconnect the phone until you have re-
solved the problem.
21
CLEANING THE TAPE-
HANDLING PARTS
THE FCC WANTS YOU
TO KNOW
Dirt, dust, or particles of the tape's
coating can accumulate on the tape
heads and other parts that the tape
touches. This can greatly reduce the
performance of the cassette player.
In the unlikely event that your answer-
ing system causes problems on the
phone line, the phone company can
disconnect your service. The phone
company attempts to notify you in ad-
vance. If advance notice is not practi-
cal, the phone company notifies you of
your right to file a complaint with the
FCC.
We recommend you inspect and clean
the tape head about every 3 months.
VOLUME
OFF
and remove
Rotate
the cassette. Then gently clean the
tape-handling parts with swab
to
a
Also, the phone company can make
changes to its lines, equipment, oper-
ations, or procedures that could affect
the operation of your answering sys-
tem. The phone company notifies you
of these changes in advance, so you
can take the necessary steps to pre-
vent interruption of your phone ser-
vice.
dipped in tape head-cleaning solution,
available at your local RadioShack
store.
Tape Head
Capstan
Pinch Roller
Tape Guide
LIGHTNING
Caution: To avoid damage to the tape
head, never use a chemical not ap-
proved for tape head cleaning and
never touch the tape head with your
fingers or any metal object.
Your answering system has built-in
protection circuits to reduce the risk of
damage from surges in phone and
power line current. These protection
circuits meet or exceed FCC require-
ments. However, lightning striking the
phone line or power lines can damage
your answering system.
Lightning damage is not common.
Nevertheless, if you live in an area
that has frequent electrical storms, we
suggest that you unplug your answer-
ing system during storms to reduce
the possibility of damage.
22
NOTES
23
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
7A7
Printed in Hong Kong
|