RCA Telephone 2 9480 User Guide

1. Plug white straight line cord into base jack LINE 1+2. Note that you must  
use a RJ14C jack.  
2. Connect to the RJ14C wall jack and position wall mount holes over the  
wall plate and slide down until base assembly is firmly in place.  
3. Plug one end of the coiled handset cord into the handset and the opposite  
end into the base.  
4. Set the RINGER 1 and RINGER 2 volume switches to HI, LO or OFF. Note in  
OFF position that line will not ring. Your telephone has separate and  
distinct ringer sounds for each line this will allow you to determine  
(audibly) the line of an incoming call.  
9-Number Memory  
Two-LineTelephone  
User’s Guide  
2-9480  
CONFERENCE  
LIMITED WARRANTY  
What your warranty covers:  
BEFORE YOU BEGIN  
SERVICE  
The conference feature enables you to carry on three-way conversation  
using LINES 1 and 2 simultaneously.  
This product may be serviced only by the manufacturer or its authorized  
service agents. Changes or modifications not expressly approved by ATLINKS  
USA, Inc. could void the users authority to operate this product. For  
instructions on how to obtain service, refer to the warranty included in this  
guide or call customer service at 1-800-448-0329.  
MODULAR JACK REQUIREMENTS  
Defects in materials or workmanship.  
You need an RJ11C or RJ14C type modular jack, which is the most  
common type of phone jack and might look like the one pictured  
here. If you don’t have a modular jack, call your local phone  
company to find out how to get one installed.  
1. Place first party on HOLD.  
2. Press the alternate LINE.  
3. Dial phone number for second party.  
4. Press CONF and talk to both parties.  
5. When finished with conference press LINE 1 or 2 to talk privately and  
disconnect other line.  
For how long after your purchase:  
One year, from date of purchase.  
(The warranty period for rental units begins with the first rental or 45 days  
from date of shipment to the rental firm, whichever comes first.)  
Or refer inquiries to:  
ATLINKS USA, Inc.  
CAUTION: When using telephone equipment, there are basic  
safety instructions that should always be followed. Refer to the  
IMPORTANT SAFETY INSTRUCTIONS provided with this product  
and save them for future reference.  
Manager, Consumer Relations  
P O Box 1976  
What we will do:  
6. When finished hang up.  
5. Set the mode switch to TONE. Note that if you have problems dialing  
switch to PULSE.  
Provide you with a new or, at our option, a refurbished unit. The exchange unit  
is under warranty for the remainder of the original products warranty period.  
Indianapolis, IN 46206  
MEMORY  
Attach your sales receipt to the booklet for future reference or jot down the  
date this product was purchased or received as a gift. This information will be  
valuable if service should be required during the warranty period.  
How you get service:  
VOLUME  
TELEPHONE BASICS  
TEMPORARY TONE FEATURE  
If you have Pulse (rotary) service, and want to access customer calling  
services that require tone dialing, such as getting information from a local  
bank, you can use this feature.  
Each of the memory buttons is capable of storing phone numbers that are up  
to 24 digits.  
Properly pack your unit. Include any cables, etc., which were originally  
provided with the product.  
The volume controls for the handset and line ringers are separate on this  
phone so you can adjust one without affecting the others.  
Proof of purchase in the form of a bill of sale or receipted invoice which is  
evidence that the product is within the warranty period, must be presented  
to obtain warranty service.For rental firms, proof of first rental is also  
required. Also print your name and address and a description of the  
defect. Send via standard UPS or its equivalent to:  
Purchase date ________________________________________________  
Name of store ________________________________________________  
TROUBLESHOOTING TIPS  
STORING A NUMBER IN MEMORY  
1. Pick up the handset.  
2. Select line 1 or 2, and wait for a dial tone.  
3. Press STORE button.  
4. Enter the telephone number to be stored.  
5. Press STORE button.  
6. Press number key 1-9 dial buttons to assign a memory address.  
7. Replace the handset.  
8. To store another number repeat steps 1-7 .  
To adjust the handset volume, use the RECEIVER HI MID LO switch on the left  
side of the phone.  
To adjust RINGER 1 and RINGER 2 volumes, use the switches on the left side  
of the base unit to choose HI, LO or OFF. Note that, if in the OFF position, that  
line will not ring. Your telephone has separate and distinct ringer sounds for  
each line allowing you to determine (audibly) the line of an incoming call.  
1. Press the TONE BUTTON (*) after you have connected to the service to  
enable Tone dialing.  
ATLINKS USA, Inc.  
Problem  
Solution  
2. When you hang up, the phone automatically returns to Pulse dialing mode.  
c/oThomson multimedia Inc.  
11721 B Alameda Ave.  
Socorro,Texas 79927  
No dial tone.  
Check hook switch to make sure it pops up.  
Check if a LINE button depressed.  
To Make a Call  
To Receive a Call  
INSTALLATION  
DESKTOP INSTALLATION  
A coiled handset cord and two straight telephone line cords are packaged  
with your unit.  
Phone dials in pulse with tone service  
Phone wont dial out with pulse service  
Make sure TONE/PULSE switch is set to TONE  
Make sure TONE/PULSE switch is set to PULSE  
1. Pick up the handset.  
2. Press LINE 1 or LINE 2.  
3. Replace the handset to hang up.  
1. Press the line number of the flashing  
indicator.  
2. Pick up the handset.  
Pay any charges billed to you by the Exchange Center for service not  
covered by the warranty.  
INSERTING A PAUSE IN THE DIALING SEQUENCE  
Phone doesnt ring  
Check RINGER VOLUME.  
You might have too many phones on one line.  
Insure your shipment for loss or damage. ATLINKS accepts no liability in  
case of damage or loss.  
A new or refurbished unit will be shipped to you freight prepaid.  
Press the REDIAL button to insert a delay in the dialing sequence of a stored  
telephone number when a pause is needed to wait for a dial tone (for example  
after you dial 9 for an outside line, or to wait for a computer access tone). Each  
pause counts as 1 digit in the dialing sequence.  
3. Replace the handset to hang up.  
FIGURE 2.  
FIGURE 1.  
Light and tone fluctuating with  
when dialing in pulse mode  
This is normal as power is feedback flutter  
phone outpulsing.  
MAKING AND RECEIVING CALLS  
Two single-line jacks  
Cord from LINE 1+2 jack  
One dual-line jack  
What your warranty does not cover:  
CHOOSE A LINE  
Cord from  
Customer instruction. (Your Owners Manual provides information  
regarding operating instructions and user controls. Any additional  
information, should be obtained from your dealer.)  
Cord from  
Cant be heard by  
other party  
Make sure phone line is connected properly.  
Make sure other phones are not OFF hook at  
the same time. If so, this is normal condition as  
volume drops when additional phones are  
used at once.  
Make sure you entered numbers correctly.  
(See Memory.)  
Press LINE 1 or LINE 2. When the handset is off hook, an indicator lights  
LINE 1+2 jack  
LINE 2 jack  
CHANGING A STORED NUMBER  
To change a stored number, you just replace it with a different number using  
the procedure for storing a number.  
above the button indicating the line is in use.  
NOTE: You can use the telephone if you have only one incoming line.  
However you cannot access a second line.  
Installation and setup service adjustments.  
Batteries.  
Damage from misuse or neglect.  
Products which have been modified or incorporated into other products.  
Products purchased or serviced outside the USA.  
Acts of nature, such as but not limited to lightning damage.  
2
4
Memory dialing  
Memory Loss  
3
(RJ14C)  
WHITE  
(RJ11C)  
(RJ11C)  
DIALING A STORED NUMBER  
1. Pick up the handset.  
2. Press the line you want (line 1 or line 2).  
3. Wait for a dial tone.  
4. Press MEM DIAL button.  
We bring good things to life.  
REDIAL  
WHITE  
WHITE  
Use REDIAL, to quickly redial the last number that was manually dialed. This  
is useful when a line is busy for a long time.  
Is Lithium battery installed correctly.  
Does lithium battery need to be replaced.  
1. Pick up the handset.  
2. Wait for dial tone.  
1
Indicator lights do not  
Turn on or off properly  
Check all of the phones on this line.  
Switch the line cord jacks for lines 1 and 2.  
Limitation of Warranty:  
EQUIPMENT APPROVAL INFORMATION  
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE  
TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED  
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR  
FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO  
VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS  
AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY  
INCREASE THE SCOPE OF THIS WARRANTY.  
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in  
compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone  
Terminal Equipment published by ACTA.  
1. (See Figure 1) If you have one dual-line phone jack (RJ14C).  
3. Press the REDIAL button. The phone automatically redials the last number  
5. Press memory address button 1-9.  
that was dialed (up to 32 digits).  
Plug the white straight cord in the LINE 1+2 jack at the top of the base.  
Plug the opposite end of the cord into the modular RJ14C dual-line jack.  
(See Figure 2) or if you have two single-line phone jack (RJ11C).  
Plug the straight cord in the LINE 1+2 jack at the top of the base.  
Plug the straight cord into the LINE 2 jack.  
Then, plug the opposite end of the cords into the modular RJ11C jacks.  
1
Notification to the Local Telephone Company  
NOTE: If you make a mistake while storing a number, hang up and repeat  
the storing procedure.  
FLASH  
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer  
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your  
telephone company.  
Press the FLASH button to activate custom calling services such as call  
waiting or call transfer, which are provided by your local phone company. Do  
not use the hook switch because you might hang up the phone.  
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of  
these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all  
devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line  
as determined by the REN, you should contact your local telephone company.  
GENERAL PRODUCT CARE  
To keep your Telephone working and looking good, follow these guidelines:  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE  
EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT  
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING  
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF  
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS  
DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED  
BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT  
PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS  
PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET  
FORTH ABOVE.  
Notes  
This equipment may not be used on coin service provided by the telephone company.  
2. Plug one end of the coiled handset cord into the handset and the opposite  
end into the base.  
3. Set the RINGER 1 and RINGER 2 volume switches to HI, LO or OFF.  
Note in OFF position that line will not ring. Your telephone has separate  
and distinct ringer sounds for each line this will allow you to determine  
(audibly) the line of an incoming call.  
HOLD  
Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if  
Avoid putting it near heating appliances and devices that generate  
electrical noise (for example, motors or fluorescent lamps).  
you are on a party line. Check with your local telephone company.  
Press HOLD button and hang up the handset. The LINE indicator blinks to  
indicate the party is on hold.  
Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.  
2
Rights of the Telephone Company  
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company  
shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is  
not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue  
service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you  
of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your  
right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and  
Regulations.  
The telephone company may make changes in its communications facilities, equipment, operations or procedures  
where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If  
these changes are expected to affect the use or performance of your telephone equipment, the telephone company  
must give you adequate notice, in writing, to allow you to maintain uninterrupted service.  
DO NOT expose to direct sunlight or moisture.  
Avoid dropping the unit and/or other rough treatment.  
Clean with a soft cloth.  
Never use a strong cleaning agent or abrasive powder because this will  
damage the finish.  
TO CONTINUE THE CONVERSATION:  
At this phone  
From another phone  
1. Pick up handset.  
4. Set the mode switch to TONE. Note that if you have problems dialing  
switch to PULSE.  
1. Pick up handset.  
2. Press LINE on hold.  
Retain the original packaging in case you need to ship it at a later date.  
WRAPPING THE TELEPHONE LINE CORD  
You may wrap the excess telephone line cord around the mounting bracket on  
the bottom of the base.  
How state law relates to this warranty:  
Some states do not allow the exclusion nor limitation of incidental or  
consequential damages, or limitations on how long an implied warranty  
lasts so the above limitations or exclusions may not apply to you.  
INTERFERENCE INFORMATION  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device  
may not cause harmful interference; and (2) This device must accept any interference received, including interference  
that may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation.  
WALL MOUNT INSTALLATION  
This warranty gives you specific legal rights, and you also may have other  
rights that vary from state to state.  
If you purchased your product outside the USA:  
This warranty does not apply. Contact your dealer for warranty information.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
2
Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the  
interference).  
Reorient or relocate and increase the separation between the telecommunications equipment and receiving  
antenna.  
Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving  
1
antenna is connected.  
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television  
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet,  
“How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government  
Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.  
US NUMBER IS LOCATED ON THE CABINET BOTTOM  
REN NUMBER IS LOCATED ON THE CABINET BOTTOM  
ATLINKS USA, Inc.  
10330 North Meridian Street  
Model 29480  
Indianapolis, IN 46290  
15799700 (Rev. 0 E/S)  
01-39  
© 2001 ATLINKS USA, Inc.  
Trademark(s) ® Registered  
Marca(s) Registrada(s)  
Printed in China  
 

RCA Camcorder EZ1100 User Guide
Roland Drums CR 78 User Guide
Rosewill Car Video System R701N User Guide
Rowenta Iron Power Press User Guide
Russell Hobbs Microwave Oven RHM1714B User Guide
Samsung Flat Panel Television 400FP 3 User Guide
Savin All in One Printer SDC306 User Guide
Sceptre Technologies Computer Monitor X20g NagaIII User Guide
Sears Washer 134474100 User Guide
Sennheiser Car Stereo System A 3700 User Guide