HEADSET SAFETY
HEADSET SAFETY (continued)
1 6 . C l e a n t h e u n i t w i t h a s o f t c l o t h s o a k e d i n a n e u t r a l d e t e r g e n t . Yo u
may damage the unit if you use an alcohol-based product. If you are
unsure if the detergent is alcohol-based, test the cleaning product on
the underside of the unit.
Follow these precautions to ensure safe usage of your wireless headphones.
1. These wireless headphones have been designed for residential use
and should not be used for industrial purposes. The headphones
should be installed and used in accordance with the instructions
contained in this manual.
1 7 . U n p l u g t h i s p r o d u c t a n d t a k e i t t o a q u a l i fied service center under
the following conditions:
2. Read through these instructions completely before installation.
Follow the instructions carefully and carry them out in the correct
order. Keep the manual on hand for future reference.
a. If liquid has been spilled into the product.
b. If the product has been exposed to rain or water.
3. The power for this headphone system is delivered with batteries.
Before charging, read the instructions in this manual. Disconnect
the power supply from the cradle/transmitter before installing or
removing batteries.
c. If the product does not operate normally when following the
operating instructions.
Audiovox declines all liability for any use that does not comply with
the instructions in this User’s Manual.
4. Always leave easy access to the main power supply.
5. Disconnect the unit from the main power supply during storms, or
if you will be absent for a long period of time.
This device complies with Part 15 of the FCC Rules. Operation of this
device is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
6. If you observe smoke or detect a burning odor, immediately
disconnect the device from the main power supply.
7. Never open the unit yourself; you may receive a severe electric
shock, leading to serious injury or even death. Take the unit to a
qualified service center when service is required.
WARNING
8. Never push objects of any kind into the openings on the cradle/
transmitter. They may touch dangerous voltage points and could
cause a fire, serious electric shock or even death.
Modification of this device to receive cellular radio-telephone service
signals is prohibited under FCC rules and federal law.
9. Protect the unit from dust, humidity and sources of excessive heat
(e.g., fireplace or radiator).
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s warranty.
1 0 . T h e p o w e r s o u r c e s h o u l d n o t b e i n c o n t a c t w i t h l i q u i d s o r e x p o s e d
to the risk of dripping or splashing liquid. Be careful not to place
the power source or cradle/transmitter near any object containing
liquid (e.g., a vase, glass or bottle).
Keep your sales receipt to obtain warranty parts and service and for
proof of purchase. Attach it here and record the serial and model
numbers. These numbers are located on the product.
11 . D o n o t e x p o s e t h e u n i t t o d i r e c t s u n l i g h t . I t s m a x i m u m a m b i e n t
temperature is 35° Celsius (95° Fahrenheit).
Model No. _____________________________________________________
Serial No. _____________________________________________________
Purchase Date: _________________________________________________
Dealer/Address/Phone: ________________________________________
_______________________________________________________________
1 2 . T h e v e n t i l a t i o n s h o u l d n o t b e i m p e d e d b y c o v e r i n g t h e u n i t w i t h
any items, such as newspapers, tablecloths, curtains, etc.
13. No flame sources, such as lighted candles, should be placed on or
close to the cradle/transmitter.
1 4 . T h i s u n i t h a s b e e n d e s i g n e d f o r u s e i n a d r y e n v i r o n m e n t . I f , f o r
exceptional reasons, you must utilize the unit out of doors (balcony,
veranda, etc.), take care to protect it from dampness (dew, rain or
splashes of liquid).
1 5 . T h e m a x i m u m a m b i e n t h u m i d i t y t h a t t h e d e v i c e s u p p o r t s i s 8 5
percent. If the unit is cold and you wish to use it in a warm room,
wait until any condensation on the unit evaporates by itself before
you turn it on.
2
3
TABLE OF CONTENTS
INTRODUCTION
Congratulations on your purchase of this wireless headphone system.
The WHP141 utilizes wireless, radio frequency transmission. The
headphones and the cradle/transmitter incorporate Double Phase Lock
Loop (PLL) Technology, which locks in the frequency on three channels
for clear and stable radio transmission reception. This 900 MHz stereo
wireless headphone system features a compact design that enables you
to enjoy music and TV sound just about anywhere inside or outside
your home. It’s simple to connect this system to any sound source,
such as a DVD, DBS, CD, TV, VCR, stereo receiver or radio.
Introduction.......................................................................................................5
Features ..............................................................................................................5
Headphone Set Description ............................................................................6
Supplied Accessories........................................................................................7
Battery Installation and Information
FEATURES
Installing the Rechargeable Batteries.......................................................7
Charging the Rechargeable Batteries .......................................................7
NiMH Rechargeable Battery Memory Effect..........................................8
NiMH Natural Power Discharge..............................................................8
NiMH Battery Warning..............................................................................8
900 MHz RF technology lets you roam freely throughout your house
Operating distance up to 150ft/45m*
No line-of-sight limitations
Convenient power, volume and tuning controls located on headphones
Automatic Level Control (ALC) and Auto On/Off function
Connecting the Cradle/Transmitter..............................................................9
Operation
Standard Usage..........................................................................................10
Maximum Performance ........................................................................... 11
Troubleshooting .............................................................................................. 11
Specifications...................................................................................................12
Warranty........................................................................................................... 13
* Range may vary by environment.
4
5
HEADPHONE SET DESCRIPTION
SUPPLIED ACCESSORIES
For stand-alone functioning, it is recommended that your wireless
headphones be powered by rechargeable batteries. The rechargeable
batteries should be installed into the battery compartment and
recharged before use. (See Battery Installation and Information, page 7).
This headphone system includes accessories that enable you to use your
wireless headphone set in a number of ways. (See section on Operation
and Standard Usage, page 9)
3.5mm/.25 inch jack adaptor
1 Rechargeable battery
compartment
Main power adapter
(AC/DC: 120 V ~ 60 Hz, 12 V = 150 mA)
2 ON/OFF switch
3
3 Recharging input
4 Power LED
indicator light
BATTERY INSTALLATION AND INFORMATION
Your wireless headphone unit requires two rechargeable AAA batteries.
Rechargeable batteries are uncharged when you purchase them. Before
you can use the wireless headphones, the batteries must be charged for
16 hours. Follow these steps to install and charge the batteries.
4
1
2
Installing the Rechargeable Batteries
Take care to follow these steps to correctly install the batteries.
1. On the right headphone, locate the battery compartment (1). Use
the finger depression on the compartment to turn the battery
compartment cover counterclockwise to remove the cover.
5 Stereo LED indicator light
6 VOLUME control
2. Insert two AAA rechargeable batteries, carefully following the
markings inside to ensure the batteries are inserted properly,
with the + and - ends in the correct positions.
7 CHANNEL switch
6
3. Replace the battery compartment cover.
Charging the Rechargeable Batteries
7
To recharge the headset unit, follow the directions below. Note: The
cradle/transmitter on the WHP141 is not a recharging cradle, although
you may place the headset in the cradle during recharging.
5
Follow these steps to recharge the NiMH rechargeable batteries.
8 Charging LED indicator light
9 Audio Signal LED indicator light
10 Charging cable
1. Make sure the ON/OFF switch (2), located on the right headphone,
is in the OFF position.
2. Connect the AC/DC main power adapter to the DC IN power
supply socket (11), located on the back of the cradle/transmitter.
11 DC IN power supply socket
8
9
12 CHANNEL switch
3. Plug the adapter into an electrical outlet.
13 Audio input cable
4. Connect the charging cable (10), located on the back of the cradle/
transmitter to the recharging input (3), located on the right
headphone. The headphones can either be placed in the cradle/
transmitter or placed next to the unit. If the headphones are
connected correctly, the charging LED indicator light on the
cradle/transmitter (8) illuminates.
10
11
12
13
6
7
CONNECTING THE CRADLE/TRANSMITTER
BATTERY INSTALLATION AND INFORMATION (continued)
Follow this quick setup guide to ensure trouble-free installation of your
headphones. To connect the cradle/transmitter to the audio source,
follow these steps.
The LED indicator on the cradle/transmitter will be on whenever
the headphones are properly plugged in to charge. Note that the
light does not go out when the batteries are fully charged. The
charge current to the headphone is very low and there is no danger
in leaving them connected for extended periods of time.
1. Connect the AC/DC main
power adapter to the DC IN
power supply socket (11) at the
back of the cradle/transmitter.
Then, connect the adaptor to an
electrical outlet. Important: This
power unit is intended
5. Charge the rechargeable batteries for 16 hours before using the
headphones for the first time. After the initial charge, an overnight
charge of 6-8 hours should be enough to return the batteries to a full
charge after use.
6. New batteries should normally last approximately eight hours
before recharging is necessary. Over time, battery replacement may
be necessary for maximum life.
to be correctly oriented in a vertical or floor mount position.
2. Insert the audio input cable (13), located on the back of the cradle/
transmitter into the headphone jack of your audio source (e.g.,
stereo, TV, CD player, DVD, etc.).
NiMH Rechargeable Battery Memory Effect
When an NiMH rechargeable battery is first used, it is important to fully
charge it and then allow it to discharge three times in order to maximize
the battery’s storage capacity. Avoid recharging the battery until it is
fully discharged. When a battery is recharged before it is completely
discharged, it develops a memory that will limit the amount of charge
in the future. This reduces the battery’s storage capacity for subsequent
charges and so reduces the amount of time your headphones can be
used before recharging is necessary.
Plugging the transmitter into the headphone outlet of a TV may
cause the TV speakers to mute. This is normal. The TV simply
thinks the user would like private listening and turns the speakers
off. If you would like to listen to the WHP141 headphones and have
the TV speakers on, you must use the stereo audio outputs of the TV,
usually located on the back or side panels. To use any RCA stereo
(red/white RCA jack) output from any device such as TV, cable box
or AV receiver will require the purchase of a 3.5mm female to RCA
stereo Y adapter (not included with the WHP141 model). To use the
adapter, simply plug the 3.5 mm jack from the transmitter into the
adapter jack, and plug the RCA ends into the audio output of your
source. Some TV models may require that you switch the audio
outputs to on, usually through the menu system. Please consult
your TV owner’s manual for specific instructions. Note that this
headphone model is compatible with analog stereo outputs only.
It is not compatible with digital outputs such as optical or coaxial
SPDIF.
NiMH Natural Power Discharge
Due to their chemical design, all rechargeable batteries incur some
degree of natural discharge. This means they automatically lose their
charge in varying degrees, and the battery’s capacity drops even
when not in use. The size of this power loss varies, depending on the
battery’s type, size, design, internal resistance and, most especially, the
temperature. The higher the temperature, the greater the power loss
through natural discharge.
3. The audio signal LED indicator light (9), located on the front of the
cradle/transmitter, illuminates as soon as you have connected the power
adapter to the outlet and the audio cable to an active signal source.
NiMH Battery Warning
If you are using NiMH or NiCd batteries, the batteries will charge when
the headphones are powered with the AC power adapter. Do not power
the headphones with the AC power adapter if you installed alkaline or
other nonrechargeable batteries—this could cause the batteries to leak.
Do not mix batteries with different chemistry types (for example, a zinc
battery with an alkaline battery). Do not mix new and used batteries.
Do not leave batteries installed in the product when not in use for long
periods. Respect the environment and the law. Before disposing of
rechargeable batteries, ask your distributor if they can be recycled and
whether or not the distributor collects rechargeable batteries for recycling.
8
9
OPERATION (continued)
OPERATION
Standard Usage
Maximum Performance
1. Switch on the audio source (TV, DVD, CD player, etc.) to which the
cradle/transmitter is connected. If your audio source is a DVD or
CD player, start a disc.
When the audio source offers a variable volume output, maximum
performance can be achieved. Variable volume outputs include
headphone jacks, computer speakers and some TV RCA output jacks.
Warning: The cradle/transmitter has an automatic function that
switches it off if it does not receive an audio signal for approximately
4 minutes. If the volume on the audio source is too low, the cradle/
transmitter also switches off after four minutes. This feature
was installed to comply with current legislation that reduces the
amount of radio emissions in the environment. To ensure that this
function is not accidentally triggered, set the audio source volume at
approximately 50 percent capacity. Consult your component user’s
manual for details on how to set the volume for headphones.
Variable Volume Output. When using an audio source with a variable
output jack, you can reduce any distortion and achieve maximum
performance by following these steps:
1. Set the volume of the audio source component to mid-level.
2. Adjust the headphone VOLUME control (6) until the desired result
is achieved.
3. If the headphone volume is not sufficient, adjust the source volume.
4. If distortion occurs, reduce the volume on the source component.
2. The cradle/transmitter is now ready to receive an audio signal. The
cradle/transmitter is activated automatically when receiving an
audio signal from the audio source.
Fixed Volume Output. When using an audio source with a fixed
volume output, regulating the volume can be achieved through the
headphone VOLUME control (6) only. Examples of fixed volume
outputs are RCA jacks (VCR, Tape, Video or CD outputs).
3. Check to make sure the audio signal LED indicator light (9) on the
front of the cradle/transmitter is lit, indicating that the unit is ready.
4. Place the headphone ON/OFF switch (2), located on the right
TROUBLESHOOTING
headphone, to the ON position.
Refer to this troubleshooting section if you encounter any difficulties
in setting up and using your headphones.
5. Check to make sure the stereo LED indicator light (5) on the left
headphone is lit, indicating a strong signal.
PROBLEM
SOLUTION
6. The cradle/transmitter and the headphones feature double phase
lock loops (PLL) for radio frequency transmissions. Select one of
the three channels on the back of the cradle/transmitter (12) and
the corresponding channel on the left headphone (7). Be sure
that the same channel (1, 2 or 3) is selected on both the cradle/
transmitter and the headphones. The Phase Lock Loop (PLL)
function automatically locks the chosen channel, providing
top-quality audio reception with no sound loss.
No sound heard • Check that your audio source, cradle/transmitter and
through the
headphones
headphones are connected, supplied properly and
turned on.
• Check to ensure that the rechargeable batteries are
installed in the headset correctly and have been
recharged properly.
• Check to ensure the cradle/transmitter is running
and the audio signal LED indicator light (9) on the
unit is lit.
7. Before wearing headphones adjust the volume using the VOLUME
control (6), located on the left headphone, to a comfortable volume
level.
• Check that the audio source is delivering a sufficient
signal to the cradle/transmitter through the audio
input cable (13). Use the VOLUME control (6) to
increase the sound level.
8. When you are through using the headphones, switch them off using
the ON/OFF switch (2), and place the audio source on standby.
• Check to ensure the audio outputs of your TV are “live”
when you are connecting to the stereo audio outputs
(RCA jack). You may need to go into the TV menu
system to ensure these outputs are turned on. Refer to
your TV user manual for more details.
• Check that the headphone and transmitter are set
to the same channel.
* Range may vary by environment.
10
11
TROUBLESHOOTING (continued)
12 MONTH LIMITED WARRANTY
Audiovox Electronics Corporation (the “Company”) warrants to the original retail purchaser
of this product that should this product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 12 months from the date of original
purchase, such defect(s) will be repaired or replaced (at the Company’s option) without charge
for parts and repair labor. To obtain repair or replacement within the terms of this Warranty,
the product along with any accessories included in the original packaging is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation
prepaid, to the Company at the address shown below. Do not return this product to the Retailer.
PROBLEM
SOLUTION
Poor sound
quality or
interference
• Check to ensure that the sound provided by the audio
source is loud enough and of sufficient quality. Make
sure the stereo LED indicator light (5) is lit.
• Check if the batteries in the headphones have sufficient
power. Recharge or replace them, if necessary.
• Check to see if you have selected the best transmission
channel (1, 2, or 3) to provide the optimum signal
reception. If necessary, try another channel on both
the headphones (7) and the cradle/transmitter (12).
This Warranty is not transferable and does not cover product purchased, serviced or used
outside the United States or Canada. The warranty does not extend to the elimination
of externally generated static or noise, to costs incurred for the installation, removal or
reinstallation of the product. The warranty does not apply to any product or part thereof which,
in the opinion of the company, has suffered or been damaged through alteration, improper
installation, mishandling, misuse, neglect, accident or exposure to moisture. This warranty
does not apply to damage caused by an AC adapter not provided with the product, or by
leaving non-rechargeable batteries in the product while plugged into an AC outlet.
• Check if the distance between the headphones and
the cradle/transmitter is within the operating range.
(The effective range of this device is approximately
150ft/45m.*) Move closer to the cradle/transmitter
to receive the sound.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED
TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL
THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities.
ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED
TO DURATION OF THIS WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER, INCLUDING ANY IMPLIED WARRANTY, MUST BE BROUGHT WITHIN
A PERIOD OF 24 MONTHS FROM THE DATE OF ORIGINAL PURCHASE. IN NO CASE
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER. No person or representative is authorized to assume for the
Company any liability other than expressed herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you specific legal rights and
you may also have other rights which vary from state/province to state/province.
• Check that the audio source provides stereo sound.
Power cut off
• The cradle/transmitter has an automatic power off
function. When no signal is received through the
cradle/transmitter’s audio input cable, it switches
off. Switch on your audio source again, and use the
CHANNEL switches (7 & 12) to adjust reception.
If necessary, increase the audio source’s volume.
SPECIFICATIONS
Model
WHP141
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit 3, Door 16,
Mississauga, Ontario L5T 3A5
Description
Radio Frequency
Wireless Headphone System
Transmitter
Carrier Frequency
900 MHz
Effective Range
Up to 150ft/45m – Range may vary by environment.
12V 150 mA
Power Supply
Transmission Frequency
UHF – 900 MHz/three channels:
912 MHz (1), 912.5 MHz (2), and 913 MHz (3)
Headset Power Supply
Two AAA type 1.2V NiMH rechargeable
batteries included
12
13
|