Python Automobile Alarm 871XP User Guide

Model 871XP

_➤Owner’s Guide

CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM

OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER

VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.

CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY

AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY

CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE

AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.

DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-

ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,

INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF

EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY

AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER

DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-

TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on

how long an implied warranty will last or the exclusion or limitation of incidental or con-

sequential damages. This warranty gives you specific legal rights and you may also have

other rights that vary from State to State.

This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-

rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-

876-0800. Directed security systems, including this unit, are deterrents against possible

theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft

of the automobile, its parts or contents; and hereby expressly disclaims any liability what-

soever, including without limitation, liability for theft, damage and/or vandalism.

Directed does not and has not authorized any person or entity to create for it any other

obligation, promise, duty or obligation in connection with this security system.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤ Date of purchase

➤ Your full name and address

➤ Authorized dealer's company name and address

➤ Type of alarm installed

➤ Year, make, model and color of the automobile

➤ Automobile license number

➤ Vehicle identification number

➤ All security options installed on automobile

➤ Installation receipts

table of contents

limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2-way remote diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

standard remote configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

standard remote button configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2-way remote functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Out of Range Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

programming remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

warning! safety first. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

arming while driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

disarming without a 2-way remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

panic mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

remote start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

short-run/turbo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Auxiliary Outputs (Options) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

safety features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

over and under rev protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

arming diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

system status chirps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

what is included

➤ A control module

➤ An XHF2 transceiver/antenna

➤ One 4-button 2-way remote

➤ A Stinger™ DoubleGuard two-stage shock sensor

➤ A Revenger™ Soft Chirp™ six-tone programmable siren

➤ A status LED indicator light

➤ A push-button Valet switch

➤ Your warranty registration

➤ A shut-down toggle switch

important information

Congratulations on the purchase of your combination remote

start alarm system. Due to the complexity of this system, it must

be installed by an authorized dealer only. Installation of this

product by anyone other than an authorized dealer voids the

warranty. All dealers are provided with a preprinted dealer certif-

icate to verify authorization.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing our web site at www.directed.com.

your warranty

➜

Your warranty registration must be completely filled out and

returned within 10 days of purchase. Your product warranty

will not be validated if your warranty registration is not returned.

Make sure you receive the warranty registration from your dealer.

It is also necessary to keep your proof of purchase, which reflects

that the product was installed by an authorized dealer.

fcc/id notice

➜

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

caution

➜

This product is designed for fuel injected, automatic transmission

vehicles only. Use of this product in a standard transmission

vehicle is dangerous and contrary the product's intended use.

2-way remote diagram

standard remote configuration

Unlock/Lock Indicator (Orange)

Receive/Transmit Indicator (Green)

Remote Start/Auxiliary Indicator (Yellow)

Panic Indicator (Red)

Lock Button

Unlock Button

Remote Start Button

Auxiliary Channel Button

standard remote button configuration

Arm

Panic

On/Off function.

controls the

and

Disarm

Panic

Off function.

controls the

and

Silent Mode™

Auxiliary

controls

controls the

and

channel output.

Remote Start

function.

Timer

pressed together control the

mode.

Turbo/Short Run

and

pressed together control

and

pressed together control channel output.

pressed together control channel 5 output.

and

pressed together control the rear

defogger.

and

pressed together control channel 6 output.

system maintenance

This system needs no specific maintenance beyond remote

control battery replacement. The remote is powered by a 1.5V

AAA battery.

Low Battery Notification

If the battery is low (and this feature is programmed On) the 2-

way remote will emit 2 long beeps 5-seconds after a transmission

is completed. The 2 long beeps will repeat every 25 seconds up to

3 times (or until a 2-way remote button is pressed).

Battery Replacement

Gently pull the end of the battery door away from the top of the

remote control then slide the door up to expose the battery and

remove the expired battery. Place the new battery into the remote

control observing the correct polarity. When power is returned

the remote control will light all icons and generate melodies

(representing all beeper tones).

2-way remote functions

The receiver uses a computer-based Learn Routine to learn the 2-

way remote buttons. This makes it possible to assign any 2-way

remote button to any receiver function. The 2-way remote

initially comes programmed with Standard Configuration, but

may also be customized by an authorized dealer. The buttons in

all of the instructions in this manual correspond to a Standard

Configuration 2-way remote.

standard configuration

➜

Button

The arming function is controlled by pressing this button for

one second. Pressing and holding this button for more than

3-seconds will trigger the panic mode.

Button

The disarming function is controlled by pressing this button for

one second. Pressing this button during panic mode will turn off

the panic mode.

Button

Silent Mode™ and an optional auxiliary function are controlled

by this button. (Silent Mode works by pressing this button for

less than one second before arming or disarming. An optional

auxiliary function, such as trunk release, can be controlled by

pressing this button for 1.5 seconds.)

The auxiliary output controls __________________________.

Button

The remote start feature is turned On/Off by pressing this button twice.

and

Buttons

The remote start timer mode function of the system is controlled

by pressing these buttons simultaneously.

and

Buttons

The Turbo/Short Run feature is controlled by these buttons (refer

to the Turbo/Short Run section for additional details).

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

Button

Press and hold this button for 3-seconds to enter Panic Mode.

and

Buttons

When simultaneously pressed these buttons control the rear

window defogger during remote starting.

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

remote operation

The remote start system operates at 434 MHz and incorporates

Directed’s proprietary XHF2 out-board technology transceiver. The

high frequency combined with Binary Data communication achieves

superior range with two-way communication.

system signal paging features

➜

A page is the signal the control module sends to the remote control

as confirmation of receipt of a command or alarm system status.

When the remote control receives a page it will generate a page noti-

fication to the user (notifications are audible beeps) and the LED

Icons will display the current system status.

Command Page

When a command (arm/disarm, remote start, or auxiliary

channel) from the remote control is sent and received, the system

will send a command page back to confirm receipt.

Alarm Page

If the alarm system is triggered while armed, an Alarm Page will

be sent to the 2-way remote control. After receipt of an Alarm

Page at the 2-way remote, the LED icons will flash and the 2- way

remote will beep the alarm system status information.

An Alarm Page alert will repeat every 100 seconds to alert the

user that the alarm system was triggered and will continue until

the alarm page is cleared. A full sensor trigger will cause the 10

rapid beep sequence Alarm Page alert and a door opening and

any other trigger will cause the 4 rapid beep sequence Alarm

Page alert.

Page Recognition (Acknowledgement)

The 2-way remote will flash an icon and beep when it has

received a triggered response and will wait for you to recognize

the violation. Briefly press the

button on the 2-way remote

while the 2-way remote is beeping to clear the alarm page. If the

alarm page was not cleared the 2-way remote will notify again at

another 100 seconds.

important! The Alarm Page alert can only be cleared dur-

ing notification, the lock button must be pressed while

the 2-way remote is beeping. The 2-way remote cansend

commands between the Alarm Page alerts (100 seconds)

Out of Range Notification

➜

If a command is issued from the remote, but the remote is

beyond the range of the vehicle to receive the command, the

remote responds with 2 sets of 3 quick beeps and the Green LED

will flash 6-times.

programming remote

To enter programming mode

Press and hold all four remote control buttons simultaneously

until one long beep is heard. Programming mode is now entered.

Beeps On/Off

Press

to select beeps On/Off. One beep is notification beeps

On, Two beeps is notification beeps Off. The notification beeps

are programmed On from the factory and can be programmed

Off if they are not desired. When programmed Off the remote

will only flash the LEDs as notification of a command page or

an alarm page.

Remote battery low notification

Press

to select low battery notification On/Off. One beep is

low battery notification On. Two beeps is low battery notifica-

tion Off. The Low battery Beeps are programmed On from the

factory and can be programmed Off if they are not desired.

When programmed Off the remote will not give any notification

that the battery charge level in the remote is low.

Page notification

The remote control can be programmed to notify the user of a

page (audibly beeping if the vehicle’s status changes, e.g. door

unlocked, engine started, vehicle violation, etc.). Press

select page On/Off. One beep is page On, Two beeps is page Off.

When programmed off the remote will not give any notification

that a page was received from the vehicle.

To exit programming mode

The remote control will exit programming mode after 2-seconds

of inactivity and will emit 2 long beeps.

using your system

warning! safety first

➜

The following safety warnings must be observed at all times:

➤ Due to the complexity of this system, installation of this

product must only be performed by an authorized Directed

dealer.

➤ When properly installed, this system can start the vehicle via

a command signal from the 2-way remote control. Therefore,

never operate the system in an enclosed area or partially

enclosed area without ventilation (such as a garage). When

parking in an enclosed or partially enclosed area or when

having the vehicle serviced, the remote start system must be

disabled using the installed toggle switch. It is the user's sole

responsibility to properly handle and keep out of reach from

children all 2-way remotes to assure that the system does not

THE USER MUST

unintentionally remote start the vehicle.

INSTALL A CARBON MONOXIDE DETECTOR IN

OR ABOUT THE LIVING AREA ADJACENT TO THE

VEHICLE. ALL DOORS LEADING FROM ADJACENT

LIVING AREAS TO THE ENCLOSED OR PARTIALLY

ENCLOSED VEHICLE STORAGE AREA MUST AT

ALL TIMES REMAIN CLOSED.

sole responsibility of the user.

These precautions are the

➤ Use of this product in a manner contrary to its intended

mode of operation may result in property damage, personal

injury, or death. (1) Never remotely start the vehicle with the

vehicle in gear, and (2) Never remotely start the vehicle with

the keys in the ignition. The user must also have the neutral

safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This

testing should be performed by an authorized Directed dealer

in accordance with the Safety Check outlined in the product

installation guide. If the vehicle starts in gear, cease remote

start operation immediately and consult with the authorized

Directed dealer to fix the problem.

➤ After the remote start module has been installed, contact

your authorized dealer to have him or her test the remote

start module by performing the Safety Check outlined in the

product installation guide. If the vehicle starts when

performing the Neutral Safety Shutdown Circuit test, the

remote start unit has not been properly installed. The remote

start module must be removed or the installer must properly

reinstall the remote start system so that the vehicle does not

start in gear. All installations must be performed by an autho-

OPERATION OF THE REMOTE

rized Directed dealer.

START MODULE IF THE VEHICLE STARTS IN GEAR

IS CONTRARY TO ITS INTENDED MODEE OF OPER-

ATION. OPERATING THE REMOTE START SYSTEM

UNDER THESE CONDITIONS MAY RESULT IN

PROPERTY DAMMAGE OR PERSONAL INJURY. YOU

MUST IMMEDIATELY CEASE THE USE OF THE

UNIT AND SEEK THE ASSISTANCE OF AN AUTHO-

RIZED DIRECTED DEALER TO REPAIR OR

DISCONNECT THE INSTALLED REMOTE START

MODULE. DIRECTED WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR

REINSTALLATION COSTS.

active arming

➜

You can arm the system by pressing

of your 2-way remote

for one second. When the system arms, from the vehicle you will

hear a short siren sound, or chirp, and see the parking lights flash

once. If the power door locks are controlled by the system, the

doors will also lock. While the system is armed, the in-vehicle

status LED will flash approximately once per second, indicating

that the system is actively protecting your vehicle. If you hear a

second chirp after arming and note that the in-vehicle’s status

LED is flashing in groups, see the Diagnostics Section of this

guide. This extra chirp is called Bypass Notification.

The remote responds to active arming with one beep and the

Orange LED will flash 3-times to indicate successful arming of

the system.

If after 2-seconds the remote beeps once and the Orange and

Red LEDs flash 3-times, the system has detected an active sensor

that should be checked.

If after 2-seconds the remote beeps once, the Orange LED flashes

6-times and the Red LED lights for 3-seconds, the system has

detected an open door, hood or trunk and has been bypassed.

passive arming

➜

The system can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming, it

will automatically arm 30 seconds after the ignition is turned off

and the system detects that you have left the vehicle by opening and

closing a door. Whenever the system is in its 30-second passive

arming countdown, the in-vehicle status LED will flash twice as

fast as it does when the system is armed. At the 20-second point of

the countdown, the siren will chirp to indicate that the system is

about to arm. At the 30-second point, the parking lights will flash

to indicate that the system is armed.

The remote responds to passive arming with one beep and the

Orange LED will flash 3-times to indicate successful arming of

the system.

note: If any protected entry point (such as a door or a

switch-protected trunk or hood) is open, the system will

not passively arm (unless forced passive arming is pro-

grammed on. See Programming Options section.) Addi-

tionally, each time a sensor is triggered during the arming

countdown, the 30-second countdown starts over.

When armed your vehicle is protected as follows:

➤ Light impacts trigger the Warn Away signal. When triggered,

the siren chirps and the parking lights flash for a few seconds.

➤ Heavy impacts trip a Triggered Sequence. The sequence

consists of the siren sounding continuously and the parking

lights flashing for a pre-programmed period, which can range

in duration from 1 to 180 seconds.

➤ If a door is opened, the system will immediately start

chirping the siren and flashing the parking lights. Three

seconds later, the siren output changes to a continuous blast.

This progressive response gives you time to disarm the system

with your 2-way remote if you inadvertently open the door

while the system is armed, while still providing instant re-

sponse (even if the door is immediately closed).

➤ Turning on the ignition key will trip the same progressive re-

sponse as opening a door.

➤ The optional starter kill prevents the vehicle’s starter from cranking.

➤ Any full trigger of the alarm system will immediately send an

alarm page to your remote informing you that your vehicle

should be checked.

multi-level security arming

➜

Multi-Level Security Arming allows you to select which of the

system's inputs or sensors will be active and which will be

bypassed when the system is armed. (See Table of Zones section

of this guide.) Pressing

again within five seconds of arming the system will activate the

Multi-Level Security feature. Each time is pressed again, a

(only in Standard Configuration)

different security level is selected. The different security levels are

selected as follows:

➤ Press

once: The siren chirps once. The system is armed.

a second time within five seconds: The siren chirps

➤ Press

twice followed by a long chirp. Zone 2 is now bypassed.

➤ Press

a third time within five seconds: The siren chirps

three times followed by a long chirp. Zone 4 is now bypassed.

➤ Press

a fourth time within five seconds:The siren chirps four

times followed by a long chirp. Zones 2 and 4 are now bypassed.

➤ Press

a fifth time within five seconds: The siren chirps

five times followed by a long chirp. All input zones, except

the ignition, are now bypassed.

note: Multi-Level Security Arming only applies to a sin-

gle arming cycle. Once the system is disarmed and then

re-armed, all the zones will be active again.

After each press of the

to reach the next level of security, the

remote will emit normal arm notification (1 beep and 3 flashes of

the Orange LED). For easiest operation in reaching each level of

after

each notification.

security, press

immediately

arming while driving

➜

Your security system can be armed while driving the vehicle!

Simply press on the 2-way remote for two seconds while the

vehicle is running. The siren will chirp once to indicate that the

security system is armed, and then once more to indicate that the

ignition is on. The system will not respond to any input except the

door triggers, and the starter kill relay (if installed) will not be acti-

vated. Once you have arrived at your destination, the system can

be disarmed by pressing the

or by turning the ignition Off.

The siren will chirp twice and the in-vehicle status LED will then

stop flashing. The system can also be disarmed at any time by

pressing

The remote will respond with the normal arming response plus a

diagnostic notification because the ignition is On. When disarmed

the remote will respond with the normal disarming response.

disarming

➜

To disarm the security system, press

. You will hear two

chirps, and the parking lights will flash twice. If the power locks

are controlled by the system, the doors will also unlock. The siren

chirping either four or five times when disarming indicates

Tamper Alert, which is described in the Diagnostics Section of

this guide.

The remote will indicate disarm notification with 2 beeps and 3

flashes of the Orange LED. If disarming after the system has been

triggered, the remote control will send a diagnostic notification as

a reminder. These diagnostic notifications are:

1. If a sensor triggered the system, the remote will beep 4-times

and the Orange and Red LEDs flash 3 times.

2. If a switch (Zone 1, 3, 5, or 6) triggered the system, the

remote will beep 4-times, the Orange LED will flash 6-times

and Red LED will illuminate for 3 seconds.

3. If the system was triggered so many times that NPC is active

the remote will emit the above notifications with 5 beeps

instead of 4.

high security disarm

➜

This system includes High Security Disarm feature. If the system

is triggered this feature allows the user to silence the siren and

reset the system to the armed state without having to visually

checking the system status.

After receiving an alarm page:

1. First press any button on the remote to clear the alarm page.

2. Press either the

button again and the High

Security disarm feature will be activated. The siren will be

silenced and the system will reset to the armed state.

3. Pressing the

button once more will fully disarm the

system and allow the vehicle to be accessed.

notes: The first press of the remote button, while the

remote is beeping, only clears the alarm page (no com-

mand is sent to the vehicle).

The transceiver transmits immediately upon system trig-

ger and does not allow disarm during the first 6 seconds

after trigger.

The 2-way remote will respond with a number of beeps

and LED flashes according to whether a pinswitch, sen-

sor, activated the alarm (and also if NPC is active).

disarming without a 2-way remote

➜

If your 2-way remote is lost or damaged, you can manually

disarm your vehicle security system. To disarm the system

without a 2-way remote, you must have the vehicle's ignition key

and know where the Valet button is located. Be sure to check

with your installer at the time of installation for both the location

and the preset response (1-5 presses) of the Valet button.

To disarm the security system,

turn the ignition to the ON posi-

tion. Press and release the Valet

DRW-35

button the preset number of times

(one to five times) within 15 seconds. After five seconds, the system

will disarm. If the system does not disarm, you may have waited too

long; turn the ignition Off and On and try again.

Location of Valet Button_________________________________

Number of Presses_____________________________________

important! The Valet button can be programmed to

respond to 1-5 presses for the disarm function. You must

check with the installer to verify the programming for

your individual unit.

The remote will indicate disarm notification with 2 beeps and 3

flashes of the Orange LED.

silent mode

➜

To temporarily turn off the vehicle’s arm or disarm chirps, use

Silent Mode™. Simply press

for less than 1-second before

arming or disarming, and the confirmation chirp(s) will be elim-

inated for that one operation only. If you want the arm/disarm

chirps turned off permanently, your dealer can do this for you.

note: The Warn Away response to lighter impacts is

bypassed if the system is armed using Silent Mode. This

ensures that no chirps will be emitted by the siren in an

area you want chirp-free. The system is still fully capable

of triggering. Only the Warn Away response is bypassed.

The remote responds with the normal arm/disarm notifications

in silent mode. (If the remote has beeps programmed On, the

remote will beep.)

panic mode

➜

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your 2-way remote. Just

press

for 3-seconds, and you will enter Panic Mode. The

siren will sound and the parking lights will flash for the

programmed siren duration. To stop Panic Mode at any time,

press

on the 2-way remote.

The remote responds with one flash of the Red LED upon

entering Panic Mode and two flashes of the Red LED upon

exiting Panic Mode.

Valet mode

➜

You can prevent your security system from automatically arming

and triggering by using Valet Mode. This is very useful when

washing the vehicle or having it serviced. In Valet Mode, the

security system will not arm, even with the 2-way remote, but all

convenience functions (door locks, trunk release, etc.) will

continue to work normally.

To enter or exit Valet Mode:

1. Turn the ignition on.

2. Turn the ignition off.

DRW-35

3. Press and release the Valet

button once within 10 seconds.

The in-vehicle status LED will light solidly if you are entering

Valet Mode, and it will go out if you are exiting Valet Mode.

The remote will respond with 3 Orange LED flashes on entering

and 2 beeps and 3 Orange LED flashes on exiting Valet Mode.

To enter or exit Valet Mode using the 2-way remote:

1. Open any vehicle door.

2. Press

3. Press

4. Press

again.

The in-vehicle status LED will light solidly if you are entering

Valet Mode, and it will go out if you are exiting Valet Mode. The

remote responds with the normal arm/disarm notifications with

each remote button press.

remote start

➜

This feature allows you to remotely start and run your vehicle for

a programmable period of time. This makes it possible to warm

up the engine, as well as adjust the interior temperature of the ve-

hicle with the climate control system. If interior heating or

cooling is desired, the climate controls must be preset, and the

fan blower must be set to the desired level prior to remote starting

the vehicle.

important!

(1) Never remote start your vehicle when the

keys are in the ignition, except when performing Valet

Take-Over, and (2) Never start the vehicle if it is not in

either PARK or NEUTRAL.

To remote start the vehicle:

1. Press

on the 2-way remote twice within 3 seconds.

2. The parking lights will flash to confirm that the vehicle will

attempt to start.

3. In gasoline vehicles, the engine will start 4 seconds after the

parking lights flash. In diesel vehicles, the engine will start

when the WAIT-TO-START indicator on the vehicle's dash

goes out or the programmed delay has ended.

4. Once the vehicle has started, it will run for the pre-program-

med period of time (either 12, 24, or 60 minutes - see

Programming Options section of this guide) or until a shut-

down input is triggered.

For a remote start, the remote responds with remote start tones

and the Yellow LED illuminates for 3-seconds.

For a remote start Off, the remote responds with remote start off

tones and the Yellow LED flashes 3-times.

important!

It is unsafe to operate a vehicle’s motor in a

garage or other closed off area. Breathing the exhaust

from the vehicle is hazardous to your health. Never acti-

vate the remote start in an enclosed space.

When you are ready to drive the vehicle:

1. Insert the ignition key and turn

it to the ON (not the START)

position.

2. Press the brake pedal.

note: If the brake pedal is pressed before the key is in the

ON position, the engine will shut down.

While the vehicle is running during remote start operation, the

system will monitor the vehicle and will automatically shut down the

engine if the system receives any of the following shut-down inputs:

➤ The brake pedal is pressed.

➤ The hood is opened.

➤ The shutdown toggle button is put into the OFF position.

➤ The pre-programmed run time (12, 24, or 60 minutes) has

elapsed.

➤ 2-way remote button

is pressed twice again to stop the

vehicle.

➤ The remote responds with remote start off tones and the

Yellow LED flashes 3-times.

valet take-over

➜

The Valet Take-Over feature allows the vehicle to remain running

after the key has been removed from the ignition. This feature is

useful for occasions when you wish to exit and lock the vehicle

for short periods of time, but would like to leave the motor

running and the climate controls on.

To perform Valet Take-Over:

1. Before turning off the engine, press and release

on the 2-

way remote twice within 3 seconds. Then wait five seconds.

2. Turn the ignition key to the OFF position. (The engine will

stay running.)

3. The engine will run until the pre-programmed time elapses

or a shut-down input is received. (See the previous Remote

Start section for a complete list of shut-down inputs.)

note: This feature will not work if the brake pedal is

being pressed.

4. The remote start responds with remote start tones and the

Yellow LED illuminates for 3-seconds.

short-run/turbo

➜

Short run turbo mode keeps the engine running after arriving at

your destination for a programmable period of 1, 3, 5 or 10

minutes. This allows the system’s timer to conveniently cool

down the turbo after you have left the vehicle.

To activate short-run/turbo:

1. Park the vehicle and set parking

2. Remove your foot from the brake pedal and leave the engine

running.

3. Press and release the

and

buttons at the same time.

4. The remote start responds with remote start tones and the

Yellow LED is illuminated for 3-seconds.

5. The lights will flash to indicate the remote start has entered

short run turbo mode.

5. Turn off the key, the engine will keep running.

6. Exit and secure the vehicle.

7. The engine will turn off after the programmed run time.

The remote responds with remote start tones and the Yellow

LED illuminates for 3-seconds.

timer mode

➜

By pressing the remote

and

buttons the parking

lights will flash 4 times and then start the vehicle and run for the

set duration. The remote start can be shut off by the 2-way

remote by pressing the remote start button

twice and

remain in timer mode, but if any other shut down zones or the

ignition become active the timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. After a 1-second delay the vehicle will start.

4. The system will start the car and will run for the specified dura-

tion, unless shut down by the remote start button

5. The system will start every 3 hours until canceled by the

brake, hood, or neutral safety shut-down wires.

On entering Timer Mode the remote will respond with the Start

On notification. The remote will respond with the Start and

Stop notification during each Start and Stop of the Vehicle while

in Timer mode.

important Timer Mode should be used only in

open areas. Never start and run the vehicle in an

enclosed space such as a garage or carport.

To exit timer mode, turn the ignition switch on any time the

engine is running. The parking lights will flash 4 times, indicat-

ing timer mode has been exited.

rear defogger

➜

To turn the rear defogger output OFF:

1. Simultaneously press & release the

buttons on the remote control.

2. The lights will flash 2 times.

3. The rear defogger output will no longer activate when the

vehicle is remote started.

note:

If the remote start is on the parking lights will turn

off then flash 2-times before returning to their normal

output and the defogger output, if active, will cease.

To turn the rear defogger output ON:

1. Simultaneously press & release the

buttons on the remote control.

2. The lights will flash 3 times.

3. The rear defogger output will once again activate when the

vehicle is remote started.

note:

If the remote start is on the lights will turn off

then flash 3-times before returning to their normal

output and the defogger output will activate as

programmed..

Auxiliary Outputs (Options)

This system also supplies outputs that can control convenience

options such as remote control trunk release and window automa-

tion. Consult your dealer for available options for your system.

Channel 2 Trunk release: When connected, pressing

seconds will remotely release the vehicle trunk lid.

for 1.5

Channel 4 auxiliary output: When connected, pressing

will immediately activate this output to control an

additional convenience option.

and

Channel 5 auxiliary output: When connected, pressing

will immediately activate this output to control an

additional convenience option.

and

Channel 6 auxiliary output: When connected, pressing

will immediately activate this output to control an

additional convenience option.

and

The remote will respond with a page notification consisting of

an output tone (once) and the Yellow LED will flash 3-times.

This occurs at the remote after the system has received the com-

mand to activate any of the Auxiliary outputs.

safety features

This system has several important safety features to ensure

proper operation of the motor and prevent accidental damage to

the engine or its components.

starter anti-grind circuitry

➜

Whenever the vehicle is remote started, advanced anti-grind

circuitry prevents the starter from engaging, even if the key is

turned to the start position. This prevents damage to the starter

motor if the key is turned to the start position during remote

start operation.

note: Anti-grind circuitry only works when the remote

start system is operating the motor and the Failsafe

Starter Kill relay is installed.

disabling the remote start system

➜

This feature allows your system's remote start unit to be

temporarily disabled to prevent the vehicle from being remote

started accidentally. This feature is useful if the vehicle is being

serviced or stored in an enclosed area. To disable the remote

start, move the shutdown toggle switch to the OFF position. The

switch can be installed in a location of your choice. Check with

your installer for recommended locations.

Location of Shutdown Switch____________________________

over and under rev protection

➜

The system monitors the engine speed and will automatically

shut the engine off if the RPMs rise above or fall below the

programmed levels. This feature prevents damage to the motor

due to fuel delivery system failures or other problems which may

cause the engine to race.

note: The system uses a wire connected to the vehicle to

sense engine speed. This wire must be connected in order

for over and under rev protection to work.

shut down inputs

➜

This security system uses several inputs to shut down the remote

start operation of the motor or prevent remote start if certain

inputs are active. The two most important are hood and brake

inputs. The hood input will prevent the motor from starting, as

well as shut it down, any time the hood is opened. The brake

pedal will shut down the motor at any time during remote start

operation, as well as preventing the remote start from activating

while it is being pressed.

nuisance prevention circuitry

➜

Your system has Directed’s Nuisance Prevention Circuitry

(NPC). It prevents annoying repetitive trigger sequences due to

faulty door pin switches or environmental conditions such as

thunder, jackhammers, airport noise, etc.

Example

If the alarm triggers three times within a 60-minute period and

each time the same sensor or switch triggers the alarm, NPC will

interpret those triggers as false alarms. After the third trigger,

NPC ignores, or bypasses, that sensor or switch (along with any

other sensors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the security system while it

is being bypassed, the 60-minute bypass period will start over.

This ensures that a sensor that is continually being triggered will

remain bypassed.

The vehicle doors are protected by NPC differently. If your secu-

rity system is triggered by an open door for three full cycles, the

system will bypass the doors until the trigger ceases.

note: Arming and disarming the system does not reset

this function! The only ways to reset a bypassed zone are

for it to not trigger for 60 minutes, or to turn on the igni-

tion. If testing your system, it is important to remember

that the NPC programming can cause zones to be

bypassed and appear to stop working. If five chirps are

heard when disarming, NPC has been engaged. If you

wish to clear the NPC memory, turn the ignition on.

diagnostics

The microprocessor at the heart of your system is constantly

monitoring all of the switches and sensors connected to it. It is

designed to detect any faulty switches and sensors and prevents

them from disabling the entire system. The microprocessor will

also record and report any triggers that occurred during your

absence. Refer to the System Status Chirps and Table of Zones

sections of this guide for diagnostic information.

arming diagnostics

➜

If the security system is armed at the same time that an input is

active (such as a door opening or sensor triggering), you will hear

one siren chirp to indicate arming and a second siren chirp to

indicate Bypass Notification. A Bypass Notification chirp means

that the security system ignores the input that was active when

the system was armed, until that input ceases. Three seconds

after that input ceases, the security system will resume normal

monitoring. For example, if your vehicle has an interior light exit

delay and you arm your security system before the interior light

turns off, you may hear a second Bypass Notification chirp.

Once the light turns off, however, the security system resumes

normal monitoring.

disarming diagnostics

➜

Extra chirps that are heard when disarming the system are the

Tamper Alert. If four chirps are heard when disarming the

system, then the security system was triggered in your absence.

If five chirps are heard when disarming the system, a zone was

triggered so many times that the Nuisance Protection Circuitry

has bypassed that zone. In either case, the in-vehicle status LED

will indicate which zone was involved (see Table of Zones

section). The security system will retain this information in its

memory and chirp four or five times each time it is disarmed,

until the next time that the ignition is turned on.

system status chirps

➜

The siren will chirp when arming/disarming the system. The

pattern of chirps will audibly report the system’s status as

described below.

Action

Arm

Number of Chirps

Description

System armed

Arm

1 (3-second delay), 1

System armed with

Bypass Notification

Disarm

System disarmed

System disarmed with

Tamper Alert

Disarm

System disarmed NPC

active

table of zones

➜

A zone is represented by the number of in-vehicle status LED

flashes used by the system to identify a particular type of input.

Standard input assignments are listed in the following table,

along with spaces to write in any optional sensors or switches

that have been installed.

ZONE

DEALER-INSTALLED

OPTIONS

(Number of

DESCRIPTION

LED Flashes)

Instant trigger - trunk pinswitch

A heavier impact

detected by the shock sensor

Door switch trigger

For optional sensors

Ignition trigger

Instant trigger - hood pinswitch

interpreting zone diagnostics

➜

Warn Away responses are not reported by arming or disarming

diagnostics. If you receive a Bypass notification when arming or

a Tamper Alert notification when disarming, look at the LED in

the car. Active or triggered zones will be indicated by a pattern of

blinks by the LED.

Example

If zone 3 was active or triggered, the in-vehicle status LED will

blink three times with a two-second pause. Then it will blink

three times again, and repeat until the ignition is turned on.

note: Your system stores the last two triggered zones in

memory. If your system has been triggered but the in-

vehicle status LED has been reset by turning on the igni-

tion, your dealer can still recall the last two zones that

were triggered. Contact your dealer for details.

code hopping

The receiver and 2-way remotes use a mathematical formula

called an algorithm to change their code each time the 2-way

remote is used. This technology has been developed to increase

the security of the unit. The control unit knows what the next codes

should be. This helps to keep the 2-way remote “in sync” with the

control unit even if you use the remote control out of range of

the vehicle. However, if the remote has been pressed many times

out of range of the vehicle, or the battery has been removed, it may

fall out of sync with the control unit and fail to operate the

system. To re-sync the remote simply press several times

within range of the vehicle. The alarm will automatically re-sync

and respond to the 2-way remotes normally.

high frequency

Your system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range, even in areas with high

radio interference.

owner recognition

Owner Recognition is a revolutionary new feature available only

from Directed. Using a Directed Bitwriter, hand-held program-

ming tool, your dealer can program many of the system settings.

The programmer makes it possible to program different settings

for each 2-way remote that is used with the system. Then, when-

ever a specific 2-way remote is used, the system will recall the

settings assigned to that 2-way remote. Owner Recognition lets

up to four users of the system have different settings that meet

their specific needs. It is almost like having four separate alarms

in your vehicle, one for each user.

note: Owner Recognition cannot be programmed with-

out a Bitwriter and the necessary software. Check with

your dealer for more information.

rapid resume logic

This Directed system will store its current state to non-volatile

memory. If power is lost and then reconnected the system will

recall the stored state from memory. This means if the unit is in

Valet Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet Mode. This applies to all states of the system

including arm, disarm, and Valet Mode.

power saver mode

Your system will automatically enter Power Saver Mode while

armed or in Valet Mode, after a period of time in which no oper-

ation has been performed. This lowers the current draw on the

vehicle's battery. Power Saver Mode takes over under the

following conditions:

➤ Power Saver when the system is armed: After the system has

been armed for 24 hours the in-vehicle status LED will flash

at half its normal rate, decreasing the system's current draw.

➤ Power Saver in Valet Mode: When the system enters Valet

Mode the in-vehicle status LED illuminates steadily. If the

vehicle is not used (ignition is not turned on) for a one hour

period while the system is in Valet Mode, the in-vehicle

status LED will shut off. If the system remains in Valet

Mode, the in-vehicle status LED will come back on the next

time the ignition is turned on and then back off.

programming options

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some

may require installation labor.

The following is a list of the programmable options, with the

factory settings in Bold.

Active

➤

arming (2-way remote only) or passive arming (auto-

matic arming 30 seconds after the last door has been closed).

➤ Arming/disarming siren chirps

or off.

➤ The ignition controlled door lock feature

or off: When

this feature is programmed on, the doors will lock three

seconds after the ignition is turned on, and unlock when the

ignition is turned off. If your installer is programming the

security system with the Directed Bitwriter, ignition lock

and unlock are independent features that can be

programmed separately.

active door

➤ Passive door locking (with passive arming) or

locking

(only when arming with the 2-way remote). Passive

locking allows the vehicle's doors to lock when the security

system passively arms (after the 30-second countdown). This

feature only works if passive arming has been programmed.

enabled

/disabled when the ignition is turned on.

➤ Panic mode

(Some states have laws against sirens sounding in moving cars.)

➤ Forced passive arming

or off. If your security system is

programmed for passive arming and the forced passive

arming feature has been programmed on, the system will

passively arm after one hour, even if a protected entry has

been left open. Forced passive arming ensures that the

system will be armed if a door has accidentally been left ajar

when leaving the vehicle.

note: When the system passively arms after one hour, the

entry point that has been left open, and anything con-

nected to the same zone, is bypassed and cannot trigger

the system. However, the remaining inputs to the system

are fully operational.

➤ Full trigger response

or 60 seconds: This determines how

long the full triggered sequence lasts. Some states have laws

regulating how long a security system can sound before it is

considered a nuisance. If your installer is programming the

security system with the Directed Bitwriter, the full triggered

response can be programmed for any duration ranging from

1 to 180 seconds.

off

➤ Automatic Engine Disable (AED) on or . The purpose of

this feature is to protect the vehicle from being stolen at all

times, regardless of whether or not the alarm is armed. If

AED is programmed on, the starter of the vehicle will be

disabled 30 seconds after the ignition is turned off. Once the

key is turned off, the in-vehicle status LED will flash slowly

(one-half its normal armed rate) to indicate the AED arming

cycle. Thirty seconds later, the starter will be disabled. To

start the car, it will be necessary to disarm the system with the

2-way remote. It is also possible to disarm the AED feature

by turning the ignition key to the RUN position and pressing

the Valet button the programmed number of times. AED is

also disabled when the system is in Valet mode.

note: This feature will only function if the FailSafe

Starter Kill relay has been installed.

™

➤ Siren tones and chirp volume. The output of the Revenger

™

Soft Chirp siren consists of six different tones in sequence.

Any of these tones can be eliminated by a dealer, resulting in a

unique, easily identifiable siren sound. The chirps can be either

6 decibels quieter

full volume or

than the full alarm blast.

➤

, 24, or 60 minute run time. your system can be

programmed to allow the vehicle to run for 12, 24, or 60

minutes when remote started.

➤ 3, 6, 9, or

minute timer mode run time. Your system can

be programmed to allow the vehicle to run for 3, 6, 9, or 12

minutes when remote started in timer mode.

➤ While the remote start system is running the engine, the

flash on and off

parking lights of the vehicle can

and light steadily.

or come on

➤ Comfort closure is a programming option which closes the

vehicle’s windows after remote locking.

security & convenience expansions

Listed below are some of the many expansion options available.

Please consult your dealer for a complete explanation of all the

options available to you.

Audio Sensor: Metal on glass, glass cracking, and breaking

glass produce distinctive acoustic signatures. The 506T audio

sensor uses a microphone to pick up sounds, then analyzes them

with proprietary acoustic software to determine if the glass has

been struck.

Backup Battery: The 520T keeps the system armed, triggers the

alarm and keeps the starter interrupt active if main battery is dis-

connected.

Hood Lock: Prevents the vehicle’s hood from being opened

without a key, keeping thieves away from the system’s siren, the

battery connections, and other components under the hood.

Field Disturbance Sensor: An invisible dome of coverage is estab-

lished by installing the 508D “radar” sensor. Your system can react

to any intrusions into this field with the full triggered sequence.

Power Locks: This system offers lock outputs that can control

some manufacturers' power door lock systems. For other

systems, additional parts may be required.

PowerTrunk Release: The accessory output of the system can op-

erate a factory power release for the vehicle’s trunk or hatch.

Although the on-board relay can control most power trunk re-

leases, sometimes an optional relay is required. If the factory

release is not power-activated, Directed 's 522T trunk release

solenoid can often be added.

Power Window Control: Automatic power window control is pro-

vided with the 529T and 530T systems. These can operate

power windows, and can roll them up automatically when the

system is armed, roll them down, or both up and down.

Mobile Video: This system is compatible with Directed Video’s

MCB1000 Multi-Channel Controller, featuring on-screen secu-

rity system programming and zone trigger information.

glossary of terms

2-Way Remote: Hand-held, 2-way transceiver which operates the

various functions of your system.

Control Unit: The “brain” of your system. Usually hidden under-

neath the dash area of the vehicle. The control unit houses the

microprocessor which monitors your vehicle and controls all

system functions.

Fault-Proof Starter Interrupt: An automatic switch controlled by

your system that prevents the vehicle’s starter from cranking

whenever the system is armed. The vehicle is never prevented

from cranking when the system is disarmed, in Valet Mode, or if

the starter interrupt switch itself fails. Your system has feature-

ready circuitry for the starter interrupt, however installation may

require additional labor.

Input: A physical connection to the system. An input can be

provided by a sensor, pinswitch or by existing systems in the

vehicle, such as ignition or courtesy lights.

In-vehicle status LED: A light mounted at a discretionary location

inside the vehicle. It is used to indicate the status of your system.

Shock Sensor: This system has a dual zone shock sensor. This

sensor is mounted in the vehicle and designed to pick up impacts

to the vehicle or glass.

2-Way Remote: A hand-held, remote control which operates the

various functions of your system.

Trigger or Triggered Sequence: This is what happens when the

alarm “goes off” or “trips.” The triggered sequence of your

system consists of the siren sounding and parking lights flashing

for the programmed duration.

Valet Button: A small push button switch mounted at a discre-

tionary location inside the vehicle. It is used to override the

starter interrupt when a 2-way remote is lost or damaged, or to

enter or exit Valet Mode.

Warning Zone Response: Lighter impacts to the vehicle will

generate the Warning Zone response. It consists of several

seconds of siren chirps and parking light flashes.

Zone: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular

zone. Often two or more inputs may share the same zone.

quick reference guide

Arming

To arm, press

■

. When the system arms, you will hear a short chirp, and

the parking lights will flash once.

Arming while driving

To arm the system while driving, press

■

on your 2-way remote while the

vehicle is running. The system will chirp once and then once more to indi-

cate that the ignition is on.

Disarming

To disarm, press

flash twice.

■

. You will hear two chirps, and the parking lights will

High security disarm

■

For high security disarm, press

on your 2-way remote and the siren will

stop sounding. To completely disarm the security system, press again and the

system will chirp 4 or 5 times (reporting the trigger).

Disarming without a 2-way remote

■

Turn on the ignition. Press the Valet button within 15 seconds. The system

should now disarm. If it does not, you may have waited too long, so turn the

ignition off and on and try again.

Silent Mode^™

Pressing

tion chirp(s) for that one operation only.

■

briefly before arming or disarming will eliminate the confirma-

Panic Mode

Press

and the parking lights will flash for 30 seconds. To stop Panic Mode at any

time, press on the 2-way remote again.

■

for 2 seconds, and you will enter Panic Mode. The siren will sound

To remote start the vehicle

Press and simultaneously. The parking lights will turn on (if

■

connected) and the vehicle will start and run for the programmed period of

time.

To disable the remote start system

■

To disable the remote start, move the shutdown toggle switch to the OFF

position.

Location of Valet button_________________________________

Number of Valet button pulses for disarming_______________

Valet Takeover

■ Press and release

on the transmitter twice in 3 seconds. Turn the

ignition key to the OFF position. Once the vehicle has started, it will run

for the pre-programmed period of time (12, 24, or 60 minutes).

Rear Window Defogger

■ Press the ,

, and

buttons simultaneously to turn the

defogger on or off when remote start-

ing. When a remote start is initiated, the parking lights will flash 2-

times if the defogger is set to off, and will flash 3-times if the defogger

is set to on.

The company behind this system is Directed Electronics

Since its inception, Directed Electronics has had one purpose, to provide consumers with

the finest vehicle security and car stereo products and accessories available. The recipient of

nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

(800) 274-0200

Call

for more information about our products and services.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Vista, CA 92081

www.directed.com

G567P 07-05

Radica Games Video Gaming Accessories 76016 User Guide
RCA MP3 Player TC1500A User Guide
Ricoh All in One Printer 2015 User Guide
Ricoh Camcorder RR211 User Guide
Roadmaster Car Stereo System MP320 User Guide
Ryobi Trimmer 155r User Guide
Samsung Home Theater System AH68 02256G User Guide
Samsung Printer ML 186XW User Guide
Sanus Systems Indoor Furnishings WMS3 User Guide
Scotts Lawn Mower S2546 User Guide