Part 55-Adjjusting diisplay and using cord management
Route cords along articulating arms using cord management clips.
Articulating arms can be adjusted to position display into desired location.
Use wrench(8) to tighten and loosen the tension screw. Do not overtighten
or overloosen to make the screws come out.
INSTALLATION GUIDE
Item No.:PSWLE82
180°
180°
180°
-5°~15°
Wrench
4x4
Wrench
5x5
5°
Thank you for choosing our product
TV Size Range: 37"～55"
Maximum Weight Capacity: 35kg/77lbs
VESA: 700X500
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
Warning
Safety automatic lock
Unlock cord
This product contains small items that could be a choking hazard if swallowed. Keep
these items away from young children!
1.Make sure these instructions are read and completely understood before attempting
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
www.pyleaudio.com
CAUTION
This product was designed to be installed on wood stud walls and solid concrete walls.
Before installing make sure the supporting surface will support the combined load of the
equipment and hardware. Never exceed the Maximum Load Capacity. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or
personal injury.The depth of this mount(1.3") may not provide sufficient space for proper
ventilation on some screens. Please refer to the manufacturer’s requirements for mounting
your screen befourinstallation.
2.The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; otherwise the structure must be reinforced.
3.Safety gear and proper tools must be used. A minimum of two people are required
for this installation. Failure to use safety gear can result in property damage, serious
injury or death.
-8-
Part 3-Atttachingg bbrackets tto screen
Part 1aa-Wood SStud Moouunting
Center brackets vertically on back of screen. Select the small(A),medium
(B or C) or large(D) screws. Attach brackets to screen using four selected
screws and four square washers(E) at the top and bottom of each bracket.
Tighten screws firmly. Do not overtighten.
Use wall plate(1) as a template, make sure it is level, and mark four mounting
holes along the center lines of the wood studs. Drill four 3/16”(5mm)dia.
holes 2”(50mm) deep. Level wall plate(1) and attach to wall with four long
bolts(G) and four washers(F). Tighten screws firmly. Do not overtighten.
2”(50mm)
Square washer(E)
E
Large hole for
M8 screws
A-D
Φ3/16”(5mm)
Medium hole for
M5 and M6 screws
Small hole for
M4 screws
Stud finder
Wood stud
Magnetic removable
bubble level
F
G
-3-
-6-
Part 1b--Concrette Wall MMoounting
Part 2-Atttachiing pllaastic coveers to wall plate
Level wall plate(1) and use wall as a template to mark four holes. Drill four
3/8”(10mm) dia. holes 2”(50mm) deep. Insert four anchors(H) into holes
and secure wall plate with four long bolts(G) and four washers(F).Tighten
screws firmly. Do not overtighten.
Secure plastic covers over wall plate by pushing them toward each other
until they lock in place.
5
2”(50mm)
Φ3/8”(10mm)
Concrete Wall
If you think the ribbon is too long, You can hide it at the back of the
televesion,once you want to uninstall the TV, it can help you to take out the
brackets.
Magnetic removable
bubble level
F
G
3
-5-
-4-
|