User’s Manual UA-PRO210
Supports up to 100 lbs / 45 kg
Included Mounting Hardware
You Will Need
1 UA-PRO210 mount
(x1)
A Level
B Stud Finder
C Marker
D Drill
E 3/16” or 3/8” drill bit
F Hammer
2 M4, M5 & M6 x 10 bolts (x4)
3 M4, M5 & M6 x 12 bolts (x4)
4 M4, M5 & M6 x 25 bolts (x4)
5 M4, M5 & M6 x 40 bolts (x4)
6 5/16” x 3” lag bolts
7 Concrete anchors
8 Ø 10 washers
(x2)
(x2)
(x2)
400 mm VESA
extension (x4)
9 Square washers
5 & 6 mm hex key
To reach
400x400 mm
use extensions
Arm
Cable Cover
Wall Bracket
End Cover
Tilt
Cover
Bracket
vBar
INSTALLATION UA-PRO210
1
Step 1:
Separate arm from display bracket:
1.1 Dissassemble tilt mechanism
by loosening top bolts (A) and
removing lower bolts (B).
1.2 Pull up and away the display
bracket from the arm.
A
B
A
B
Step 2:
Mount TV on display bracket:
2.1 Loosen 4 adaptor plate bolts
(C) so both VBars (D) can slide.
2.2 Slide Vbars to match mounting
holes on TV.
2
2.3 Insert matching TV bolts (E)
and tighten slightly.
2.4 Tighten adaptor plate bolts (D)
2.5 Re-assemble tilt mechanism.
C
D
E
INSTALLATION (2) UA-PRO210
Step 3:
a) Mounting to a wood stud:
3.0a Locate the wood stud.
3.1a Place the mount to a suitable
location and height.
3
3.2a Using a bubble level, hold the
mount in a level position and mark
the holes position.
3.3a Drill 3/16” holes.
b) Mounting to a masonry wall:
3.1b Place the mount to a suitable
location and height.
G
F
3.2b Using a bubble level, hold the
mount in a level position and mark
the holes position.
3.3b Drill 3/8” holes, insert the
wall anchor and tap them flush to
the wall with a hammer.
3.4 Attach the mount to the wall
with the lag bolts (F) and steel
washers (G) supplied.
3.5 While the lag bolts are still
slightly loose, check to make sure
that the mounting plate is vertical.
Adjust if necessary. Covered with
the supplied molded caps.
4
A
B
Step 4:
Reattach tilt mechanism:
4.1 Put back the display bracket on
the arm hanging on left bolts (A).
4.2 Put back removed bolts (B).
4.3 Leave bolts (A and B) while
adjusting tilt angle.
4.4 Tighten at desired position.
4.5 If necessary, adjust horizon
with bolts (H).
A
B
H
INSTALLATION (3) UA-PRO210
Step 5:
Cable Management:
5.1 To install the cable, first you
5
need to remove the end cover (I)
and slide the cable cover (J) out
from the arm.
5.2 Do the same for the rest of the
cable covers before installing the
cables.
5.3 Install the cables and slide the
covers back to the arm.
5.4 Install the end covers.
I
A
B
J
Step 6:
Adjusting the Display:
6
6.1 Slight loosen Bolt (A); do not
loosen fully or remove it, otherwise
injury may occur.
6.2 Grasp the upper and lower
edge of the Display, and then push
or pull the Display to the
desired tilt angle.
A
B
H
6.3 Tighten Bolt (A).
6.4 If necessary, adjust horizon
with bolts (H), as in step 4.5.
FOR MORE INFORMATION VISIT
ProMountsTM name, logo and model numbers are property of ProMounts.
© ProMountsTM 2010
|