Printronix Guide Specification
RFID Label
915 MHz, 96 Bit, EPC Class 1, Gen 2
Rafsec Short Dipole Antenna
Applicable Printer Models
Print and Apply Models
SLPA8000r MP2
Desktop Models
SL4M MP2
SLPA7000r MP2
SL5000r MP2
Disclaimer
Notwithstanding anything to the contrary in this document, the guidelines, suggestions and other information
included in this document or otherwise provided to the recipient, including the guidelines and suggestions for
developing converted RFID labels, are provided by Printronix on an "as is" basis and without warranty of
any kind whatsoever, expressed or implied. In particular, Printronix disclaims any implied warranty of
merchantability or fitness for a particular purpose. Printronix will not be liable under any circumstances for
any damages or losses related in any way to use of the guidelines, specifications or other information,
including damages, which may be incurred as a result of labels not working properly in a specific
application. All specifications subjective to change without notice. Testing of the converted labels in the
printer is recommended prior to production quantities.
2/12/07
RFID Label Guide Specification
Gen 2, Rafsec Short Dipole Antenna
182316-000 Rev C
Page 1 of 5
3.3.2. Adhesive interface to liner shall be uniform and exhibit the same release
characteristics along the full length of the label.
3.4. Perforations Between Labels
3.4.1. For SL4M and SL5000 models – per user requirements except no perforations for
Peel Mode.
3.4.2. For SLPA8000 and SLPA7000 models – no perforation between labels.
3.5. Roll Configurations
3.5.1. SL4M and SL5000 models
3.5.1.1. Inside core diameter: 3 inches (76.2 mm).
3.5.1.2. Outside roll diameter: 8" (203.2 mm) maximum.
3.5.1.3. Label wind direction – label side out with orientation per Figure 1.
3.5.2. SLPA8000 and SLPA7000 models
3.5.2.1. Inside core diameter: 3.000” (+0.032”, -0.0”) (76.190 mm (+0.813, -
0.0)) core acceptable for label lengths less than 5" (127.0 mm) with
inlay lengths less than 2" (50.8 mm). For label lengths greater than 5"
(127.0 mm) core diameter shall be 6.0" (+0.032”, -0.0”) (152.4 mm
(+0.813, -0.0).
3.5.2.2. Outside roll diameter: up to 12" (304.8 mm) maximum.
3.5.2.3. Label wind direction – label side out with orientation per Figure 1.
3.5.3. General
3.5.3.1. Roll to be wound with sufficient tension to prevent telescoping during
transit and handling.
3.5.3.2. Splices to use clear tape, should be angled and placed under the labels
and not between.
3.6. Inlay
3.6.1. Inlay: Rafsec Gen 2 Short Dipole inlay (similar to Rafsec sales code 3000704).
3.6.2. Base antenna material: Etched aluminum.
3.6.3. Nominal operating frequency: 915 (+/-15) MHz.
3.6.4. EPC Protocol: UHF Class 1, Gen 2.
3.6.5. Memory: 96 Bit Read/Write.
3.7. Label Construction
3.7.1. Inlay location with respect to label facestock outlined in Figure 1.
3.7.2. 4” Printer Models
3.7.2.1. Nominal label facestock width with inlay is 4.0" (101.6 mm).
Maximum width of label construction supported by printer is 4.5"
(114.3 mm) edge to edge (4.1" (104.1 mm) is printable).
3.7.3. 6” Printer Models
RFID Label Guide Specification
Gen 2, Rafsec Short Dipole Antenna
182316-000 Rev C
Page 3 of 5
3.7.3.1. Printable label facestock width with inlay is 6.6" (167.6 mm).
Maximum width of label construction supported by printer is 6.8"
(172.7 mm) edge to edge.
3.7.4. Minimum supported inlay pitch is 2.0" (50.8 mm).
3.7.5. Gap Sensing
3.7.5.1. Nominal gap between labels for gap sensing is 0.125" (3.17 mm).
Minimum gap supported is 0.10" (2.54 mm).
3.7.5.2. 1.0" (25.4 mm) minimum x 0.125" (3.17 mm) timing marks on the liner
under the gap.
3.7.6. Release Characteristics
3.7.6.1. Labels shall be able to dispense in a print and apply application.
3.8. Packaging and Handling
3.8.1. RFID labels are static sensitive devices and should be packaged and handled
accordingly.
3.8.2. Low humidity environments can increase electrostatic discharge (ESD) conditions.
ESD safeguards are recommended
3.8.3. Avoid storing labels in elevated temperature environment.
4. Thermal Transfer Ribbons for Printronix RFID Printers
4.1. Ribbons for 4” RFID Printer Models
4.1.1. Wax resin ribbon for best durability. Wax Resin Blend Ribbon 8500, 4.33" x 2051'
(110 mm x 625 m), package of 6 ribbons, Printronix part no. 203485-103.
4.1.2. General purpose wax ribbon. Wide Spectrum Wax Ribbon 8300, 4.33" x 2051'
(110 mm x 625 m), package of 6 ribbons, Printronix part No. 175391-103.
4.2. Ribbons for 6” RFID Printer Models
4.2.1. Wax resin ribbon for best durability. Wax Resin Blend Ribbon 8500, 6.73" x 2051'
(171 mm x 625 m), package of 6 ribbons, Printronix part no. 203485-106.
4.2.2. General purpose wax ribbon. Wide Spectrum Wax Ribbon 8300, 6.73" x 2051'
(171 mm x 625 m), package of 6 ribbons, Printronix part No. 175391-106.
5. Contact Information
714-368-2477.
RFID Label Guide Specification
Gen 2, Rafsec Short Dipole Antenna
182316-000 Rev C
Page 4 of 5
Label Perforation
Centered in Gap
(see Para 3.4)
Direction of label
travel out of
printer
Leading Edge of Label
Inlay Outline
1.00" (+/-0.125")
Trailing edge of timing
mark to leading edge
of antenna
Label
Rafsec Short Dipole
Antenna outline
Chip facing down,
center slot back
Minimum
Pitch 2.0"
2.0625"
(+/- 0.1250")
Liner edge to
center of chip
Liner
1.0" min x 0.125"
timing mark on
back side of liner
Corner radius:
0.125" typ.
4.0" minimum
Variable see para
3.7.2 and 3.7.3
Printronix RFID Label Requirements for
Rafsec Short Dipole Inlay
Viewed from Facestock Side
PRINTRONIX
All Dimensions in Inches
Figure 1. Label Layout
RFID Label Guide Specification
Gen 2, Rafsec Short Dipole Antenna
182316-000 Rev C
Page 5 of 5
|