R
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PP135
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2002 Electrolux Home Products, Inc.
530163516
11/8/02
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
UNIT / MAINTENANCE SAFETY
S Disconnect the spark plug before perform-
ing maintenance except carburetor adjust-
ments.
S Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep in good working
condition.
S Replace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
S Maintain unit according to recommended
procedures. Keep cutting line at proper
length.
S Use only 0.080! (2 mm) diameter Poulan
PRO" brand line. Never use wire, rope,
string, etc.
S Install required shield properly before using
the unit. Use only specified trimmer head; gon, and Washington require by law that
make sure it is properly installed and se-
curely fastened.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
end supported to prevent line from contact- to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
ing any object.
S Keep others away when making carburetor
adjustments.
S Use only recommended Poulan PRO" ac-
cessories and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by an au-
thorized service dealer.
LINE TRIMMER SAFETY
WARNING: Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit.
S Avoid spilling fuel or oil. Wipe up all fuel
spills.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before re-
moving fuel cap.
S Cut from your right to your left. Cutting on
left side of the shield will throw debris away
from the operator.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
S Always store gasoline in a container ap-
proved for flammable liquids.
TRANSPORTING AND STORAGE
S Allow engine to cool before storing or trans-
porting in vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acci-
dentally cause injury. The unit can be hung
by the tube.
S Store unit out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
WARNING: For each optional at-
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
WARNING: Ensure handlebar is
installed when using edger or brushcutter at-
tachments. Attach handlebar above arrow on
safety label on the upper tube (engine end of
unit). If your edger or brushcutter attachment
does not include a handlebar, a handlebar ac-
cessory kit (#530071451) is available from
your authorized service dealer.
Handlebar
3
S Never place any object in air intake opening
as this could restrict proper air flow and
cause damage to the unit.
S Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
S To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
EDGER SAFETY
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
S Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
S Allow blade to stop before removing it from
the cut.
BRUSHCUTTER SAFETY
DANGER: Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
S Always keep the wheel and depth adjusting
skid in contact with the ground.
WARNING: Do not use trimmer head
as a fastening device for the blade.
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
S Always use the handlebar when using edg-
er attachment.
WARNING: The blade continues to
spin after the throttle is released or engine is
turned off. The coasting blade can throw ob-
jects or seriously cut you if accidentally
touched. Stop the blade by contacting the
right hand side of the coasting blade with ma-
terial already cut.
BLOWER/VACUUM SAFETY
WARNING:
Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc., could be picked up by the air intake
and thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
S
b
w
S Never place objects inside the blower
tubes, vacuum tubes or blower outlet. Al-
ways direct the blowing debris away from
people, animals, glass, and solid objects
such as trees, automobiles, walls, etc. The
force of air can cause rocks, dirt, or sticks to
be thrown or to ricochet which can hurt
people or animals, break glass, or cause
other damage.
S Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tubes.
S Check air intake opening, blower tubes or S Throw away and replace blades that are
vacuum tubes frequently, always with en-
gine stopped and spark plug disconnected.
WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, etc.) which can be
thrown or become entangled in the blade or
trimmer line.
bent, warped, cracked, broken or damaged
in any other way.
Keep vents and discharge tubes free of de- S Install required shield properly before using
bris which can accumulate and restrict
proper air flow.
the unit. Use the metal shield for all metal
blade use.
4
terial when the blade is in motion. Make sure
the switch is in the OFF position, the spark
plug wire is disconnected, and the blade has
stopped moving before removing jammed
material from the cutting blade. Do not grab or
hold the unit by the cutting blade.
WARNING: Only use brushcutter at-
tachments that provide a metal shield with
proboscis nose.
Proboscis
nose
Blades move
momentarily
after the
Allow blades to stop
before removing
them from the cut.
is
d.
S Use only specified blade and make sure it is
properly installed and securely fastened.
S Cut from your left to your right. Cutting on
the right side of the shield will throw debris
away from the operator.
S Always use the handlebar and a properly
adjusted shoulder strap with blade (see AS-
SEMBLY instructions in brushcutter attach-
ment instruction manual).
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in
any other way. Have worn or damaged
parts replaced by your authorized service
dealer.
S Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S Keep the cutting blade and air vents clear of
debris.
CULTIVATOR SAFETY
WARNING: Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the engine and disconnect the spark
plug before unclogging tines or making re-
pairs.
POLE PRUNER SAFETY
WARNING: The reciprocating blade/
rotating chain can cause severe injury. In-
spect the unit before use. Do not operate unit
with a bent, cracked or dull blade or dull chain.
Keep away from the blade/chain.
WARNING: The reciprocating blade/
rotating chain is sharp. Do not touch. To pre-
vent serious injury, always stop engine and
ensure blade/chain has stopped moving, dis-
connect spark plug, and wear gloves when
changing or handling the blade or chain.
WARNING: Inspect the area to be
cultivated before starting the unit. Remove all
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact oc-
curs, stop the engine and inspect the unit
for damage.
WARNING: A coasting blade/rotat-
ing chain can cause injury while it continues to
move after the engine is stopped. Maintain
proper control of the unit until the blade/chain
S Never operate the cultivator without the tine
cover in place and properly secured.
S Keep the tines and guard clear of debris.
S After striking a foreign object, stop the en- has completely stopped moving.
Keep
gine, disconnect the spark plug and inspect hands, face and feet at a distance from all
moving parts. Do not attempt to touch or stop
the blade or chain when it is moving.
the cultivator for damage. Repair before re-
starting.
S Disconnect attachment from the drive en-
gine before cleaning the tines with a hose
and water to remove any build--up. Oil the
tines to prevent rust.
S Always wear gloves when servicing or
cleaning the tines. The tines become very
sharp from use.
S Do not run unit at high speed unless culti-
vating.
HEDGE TRIMMER SAFETY
DANGER: RISK OF CUT; KEEP
WARNING:
Falling objects can
HANDS AWAY FROM BLADE -- Blade
cause severe head injury. Wear head protec-
moves momentarily after the trigger is re- tion when operating this unit with a pole prun-
leased. Do not attempt to clear away cut ma- er attachment.
5
WARNING: Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
WARNING: Inspect the area where
the unit is to be used. Remove objects that
could be thrown or damage the unit. Some
objects may be hidden by fallen snow -- be
alert for the possibility.
WARNING: To prevent serious inju-
ry, do not use more than one boom extension
with a pole pruner attachment.
S Direct material discharge away from glass
enclosures, automobiles, etc.
WARNING: Keep the pruner away
from power lines or electrical wires.
S Only use for pruning limbs or branches up
to 4 inches in diameter.
S Do not operate the unit faster than the
speed needed to prune. Do not run the unit
at high speed when not pruning.
S Always stop the unit when work is delayed
or when walking from one cutting location to
another.
S If you strike or become entangled with a for-
eign object, stop the engine immediately
and check for damage. Have any damage
repaired by an authorized service dealer
before attempting further operations. Dis-
card blades that are bent, warped, cracked
or broken.
S Do not run engine at high speed while not
removing snow.
S Be attentive when using the snowthrower,
and stay alert for holes in the terrain and
other hidden hazards.
S Make sure the rotor will spin freely before
attaching the snowthrower to the power-
head.
S If the rotor will not rotate freely due to frozen
ice, thaw the unit before thoroughly before
attempting to operate under power.
S Keep the rotor clear of debris.
S Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
S After striking a foreign object, stop the en-
gine, disconnect spark plug and inspect the
snowthrower for damage and repair if nec-
essary before restarting unit.
S Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S Never attempt to use the snowthrower on a
roof.
S Never operate the snowthrower near win-
dow wells, dropoffs, etc.
S Never discharge snow onto public roads or
near moving traffic.
S Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow
from steep slopes.
S Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S Stop the unit immediately if you feel exces-
sive vibration. Vibration is a sign of trouble.
Inspect thoroughly for loose nuts, bolts or
damage before continuing. Contact an au-
thorized service dealer for repair or re-
placement of affected parts as necessary.
SNOW THROWER SAFETY
WARNING: Keep hands and feet
away from the rotor when starting or running
the engine. Never attempt to clear the rotor
with the engine/motor running. Stop engine
and disconnect spark plug before unclogging
snow or debris from discharge chute or when
adjusting vanes.
S Look behind and use care when backing
up. Exercise caution to avoid slipping or fal-
ling, especially when operating in reverse.
S Know how to stop quickly.
6
ASSEMBLY
WARNING: If received assembled,
WARNING: Make sure the locking/
repeat all steps to ensure your unit is properly release button is locked in the primary hole
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole.
For optional attachments, see the AS-
SEMBLY section of the applicable attach-
ment instruction manual.
ATTACHING SHIELD
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you. For proper
orientation of shield, see KNOW YOUR TRIM-
MER illustration in OPERATION section.
1. Remove wing nut from shield.
INSTALLING TRIMMER ATTACH-
MENT
CAUTION: When installing trimmer attach-
ment, place the unit on a flat surface for stabil-
ity.
1. Loosen the coupler by turning the knob
counterclockwise.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole
in bracket.
Coupr
LOOSEN
4. Securely tighten wing nut onto bolt.
Shipping
protector
Wing Nut
Bracket
Slot
Shield
Gearbox
Knob
TIGHTEN
2. Remove shipping protector from coupler.
3. Remove the tube cap from the trimmer at-
tachment (if present).
ADJUSTING THE HANDLE
4. Position locking/release button of attach-
ment into guide recess of coupler.
5. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
WARNING: When adjusting the han-
dle, be sure it remains between the trigger
and the arrow on the safety label.
1. Loosen wing nut on handle.
6. Before using the unit, tighten the knob se- 2. Rotate the handle on the tube to an up-
curely by turning clockwise.
right position; retighten wing nut.
7
KN
RENIT.
Coontrols
and
Coupler
ON/OFF SWITCH
The ON/OFF switch is located on the trigger
handle and is used to stop the engine. Move the
switch to the OFF position to stop the engine.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
COUPLER
bulb by pressing it and allowing it to return to The COUPLER enables optional attach-
its original form.
ments to be installed on the unit.
the fuel is thoroughly mixed. Always read and
follow the safety rules relating to fuel before
fueling your unit.
IMPORTANT
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage.
To avoid engine problems, empty the fuel sys-
tem before storage for 30 days or longer.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty. Use fresh fuel next season.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage
may occur.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on
unleaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. Mix
gasoline and oil at a ratio of 40:1. A 40:1 ratio
is obtained by mixing 3.2 ounces (95 ml) of oil
with 1 gallon (4 liters) of unleaded gasoline.
DO NOT USE automotive oil or boat oil.
See the STORAGE section for additional in-
formation.
HOW TO STOP YOUR UNIT
These oils will cause engine damage. When S To stop the engine, move the ON/OFF
mixing fuel, follow instructions printed on
container. Once oil is added to gasoline,
shake container momentarily to assure that
switch to the OFF position.
S If engine does not stop, move choke lever
to FULL CHOKE position.
8
Choke
position
decal
ON/OFF Switch
HOW TO START YOUR UNIT
8. Pull starter rope sharply until engine runs,
but no more than 6 pulls. If the engine
doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more than
6 pulls. If the engine doesn’t start, repeat
procedure 2 additional times.
WARNING: The trimmer head will
turn while starting the engine.
Avoid any contact with the muffler. A hot muf-
fler can cause serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE: If engine still doesn’t start, it is
probably flooded. Proceed to STARTING A
FLOODED ENGINE.
Starting Position
9. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
OFF CHOKE by aligning lever with posi-
tion shown on decal (see illustration be-
low). Allow the unit to run for 30 more se-
conds at OFF CHOKE before releasing
the throttle trigger. NOTE: If engine dies
with the choke lever in the OFF CHOKE
position, move the choke lever to the
HALF CHOKE position and pull the rope
until engine runs, but no more than 6
pulls.
Starter Handle
Choke
Lever
Primer Bulb
Muffler
Choke
position
decal
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON position.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to FULL CHOKE by
aligning lever with position shown on de-
cal (see illustration below).
STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF
CHOKE position.
3. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
Choke
position
decal
5. Allow engine to run 15 seconds, then
move the choke lever to the OFF CHOKE
position.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
5. Squeeze the throttle trigger fully and hold
through all remaining steps.
6. Pull starter rope handle sharply until en-
gine sounds as if it is trying to start, but do
not pull rope more than 6 times.
7. As soon as engine sounds as if it is trying
to start, move choke lever to HALF
CHOKE by aligning lever with position
shown on decal (see following illustra-
tion).
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
9
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
Primary Hole
Coupler
Guide Recess
OPERATING THE COUPLER
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . . . .PP1000E
Cultivator . . . . . . . . . . . . . . . . . . . .PP2000T
Blower . . . . . . . . . . . . . . . . . . . . . .PP3000B
Brushcutter . . . . . . . . . . . . . . . . . .PP4000C
Pruner . . . . . . . . . . . . . . . . . . . . . .PP5000P
Locking/
Release
Button
Attachment
Upper
Tube
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit.
WARNING: Always stop unit and dis-
connect spark plug before removing or instal-
ling attachments.
OPERATING POSITION
REMOVING TRIMMER ATTACH-
MENT (OR OTHER OPTIONAL AT-
TACHMENTS)
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Upper Tube
Coupler
LOOSEN
Lower
Attachment
Cut from your left to your right.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
TIGHTEN
Knob
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise
and vibration. The cutting line will last longer
and will be less likely to “weld” onto the spool.
2. Press and hold the locking/release button.
Locking/Release
Button
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
S Release the throttle trigger.
S Move the ON/OFF switch to the OFF posi-
tion.
Coupler
Lower Attachment
Upper Tube
3. While securely holding the engine and
upper tube, pull the attachment straight
out of the coupler.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
INSTALLING OPTIONAL ATTACH-
MENTS
1. Remove the tube cap from the attach-
ment (if present).
The most efficient line length is the maximum
2. Position locking/release button of attach- length allowed by the line limiter.
ment into guide recess of coupler.
Always keep the shield in place when the tool
3. Push the attachment into the coupler until is being operated.
the locking/release button snaps into the To advance line:
primary hole.
S Operate the engine at full throttle.
4. Before using the unit, tighten the knob se- S Hold the trimmer head parallel to and above
curely by turning clockwise.
the grassy area.
10
S Tap the bottom of the trimmer head lightly on at an angle. Allow only the tip of the line to
the ground one time. Approximately 2 inches make contact. Do not force trimmer line into
(5 cm) of line will be advanced with each tap. work area.
Always tap the trimmer head on a grassy
Trimming
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 in. (5 cm) or less,
more than one tap will be required to obtain
the most efficient line length.
3 in. (8 cm)
Above Ground
WARNING: Use only 0.080” (2 mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
SCALPING -- The scalping technique re-
moves unwanted vegetation down to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
Scalping
CUTTING METHODS
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area. The right and wrong
ways are shown below.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
Tip of the Line
Line Crowded Into
Work Area
Does The Cutting
Mowing
Right
Wrong
S The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease head
wear, especially:
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
Swee
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
11
MAINTENANCE
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts by pressing button to re-
lease air filter cover.
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screw
S Debris Shield
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter;
squeeze the filter to distribute oil.
6. Replace parts.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position. Make sure engine stops;
then restart engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
Air Filter
Button
Air Filter
Cover
INSPECT AND CLEAN UNIT AND LA-
BELS
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
SERVICE AND ADJUSTMENTS
REPLACING THE LINE
1. Remove spool by firmly pulling on tap
button.
Line exit holes
Line in Notch
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080! (2 mm) di-
ameter Poulan/Weed Eaterr brand line.
Line in Notch
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
Hub
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
6. Push the lines into the notches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
Spool
Small
Holes
7. Insert the lines into the the exit holes in
the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pull the lines extending outside of the hub
to release the lines from the notches.
12
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
REPLACING THE CUTTING HEAD
1. Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
2. Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while removing and installing trimmer
head.
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without trimmer head moving or spinning
(idle too fast) or stalling (idle speed too slow).
S Turn idle speed screw clockwise to
increase engine speed if engine stalls or
dies.
Screwdriver
S Turn idle speed screw counterclockwise to
decrease engine speed if trimmer head
moves or spins at idle.
3. While holding the screwdriver in position,
remove trimmer head by turning clock-
wise.
WARNING: Recheck the idle speed
after each adjustment. The trimmer head
must not move or spin at idle speed to avoid
serious injury to the operator or others.
4. Thread replacement trimmer head onto
the shaft by turning counterclockwise.
Tighten until secure.
5. Remove the screwdriver.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during most of this pro-
cedure. Wear your protective equipment and
observe all safety precautions. After making
adjustments, the trimmer head must not
move/spin at idle speed.
Air Filter
Cover
Idle Speed
Screw
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
If you require further assistance or are unsure
S Engine will not idle when the throttle is about performing this procedure, contact an
released.
authorized
1--800--554--6723.
service
dealer
or
call
S The trimmer head moves/spins at idle.
STORAGE
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool before storing or trans-
porting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy
storage.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
13
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Move ON/OFF switch to ON.
1. ON/OFF switch in
OFF position.
2. Engine flooded.
2. See “Starting a Flooded Engine” in
Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Contact an authorized service dealer.
6. Carburetor requires
adjustment.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
2. Fuel mixture incorrect.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
14
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
er predelivery setup or normal adjustments
warrants to the original purchaser that each explained in the instruction manual.
new Poulan PROr brand gasoline tool or at-
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
2 YEARS-- Parts and Labor, when used for
household purposes.
90 DAYS -- Parts and Labor, when used for
commercial, professional, or income produc-
ing purposes.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not SEQUENTIAL DAMAGES, SO THE ABOVE
cover damage or liability caused by improper LIMITATIONS OR EXCLUSION MAY NOT
handling, improper maintenance, or the use APPLY TO YOU.
of accessories and/or attachments not spe- The policy of ELECTROLUX HOME PROD-
cifically recommended by ELECTROLUX
UCTS, INC., is to continuously improve its
HOME PRODUCTS, INC., for this tool. Addi-
products. Therefore, ELECTROLUX HOME
tionally, this warranty does not cover tune- PRODUCTS, INC., reserves the right to
ups, spark plugs, filters, cutting line, or rotat- change, modify, or discontinue models, de-
ing head parts that will wear and require
signs, specifications, and accessories of all
replacement with reasonable use during the products at any time without notice or obliga-
warranty period. This warranty does not cov- tion to any purchaser.
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
maintenance. As the small off--road engine
TIONS: The U. S. Environmental Protection owner, you should be aware that POULAN/
Agency and POULAN/WEED EATER, DIVI-
SION OF WCI OUTDOOR PRODUCTS, INC.,
WEED EATER may deny you warranty cover-
age if your small off--road engine or a part of it
are pleased to explain the emissions control has failed due to abuse, neglect, improper main-
system warranty on your year 2001--2004 small tenance, unapproved modifications, or the use
off--road engine. POULAN/WEED EATER of parts not made or approved by the original
must warrant the emission control system on equipment manufacturer. You are responsible
your small off--road engine for the periods of for presenting your small off--road engine to a
time listed below provided there has been no POULAN/WEED EATER authorized repair
abuse, neglect, or improper maintenance of center as soon as a problem exists. Warranty
your small off--road engine. Your emission con- repairs should be completed in a reasonable
trol system includes parts such as the carbure-
amount of time, not to exceed 30 days. If you
tor and the ignition system. Where a warrant- have any questions regarding your warranty
able condition exists, POULAN/WEED EATER rights and responsibilities, you should contact
will repair your small off--road engine at no cost your nearest authorized service center or call
to you. Expenses covered under warranty in-
clude diagnosis, parts and labor. MANUFAC- WARRANTY COMMENCEMENT DATE: The
TURER’S WARRANTY COVERAGE: If any
warranty period begins on the date the small
POULAN/WEED EATER at 1--800--554--6723.
emissions related part on your engine (as listed off--road engine is purchased. LENGTH OF
under Emissions Control Warranty Parts List) is COVERAGE: This warranty shall be for a peri-
defective or a defect in the materials or work- od of two years from the initial date of purchase.
manship of the engine causes the failure of such WHAT IS COVERED: REPAIR OR RE-
an emission related part, the part will be repaired PLACEMENT OF PARTS. Repair or replace-
or replaced by POULAN/WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
ment of any warranted part will be performed at
no charge to the owner at an approved POU-
TIES: As the small off--road engine owner, you LAN/WEED EATER servicing center. If you
are responsible for the performance of the re- have any questions regarding your warranty
quired maintenance listed in your instruction rights and responsibilities, you should contact
manual. POULAN/WEED EATER recom-
your nearest authorized service center or call
mends that you retain all receipts covering POULAN/WEED EATER at 1--800--554--6723.
maintenance on your small off--road engine, but WARRANTY PERIOD: Any warranted part
POULAN/WEED EATER cannot deny warran-
which is not scheduled for replacement as re-
ty solely for the lack of receipts or for your failure quired maintenance, or which is scheduled only
to ensure the performance of all scheduled for regular inspection to the effect of ”repair or
15
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
for replacement as required maintenance shall should contact your nearest authorized service
be warranted for the period of time up to the first center or call POULAN/WEED EATER at
scheduled replacement point for that part. 1--800--554--6723. WHERE TO GET WAR-
DIAGNOSIS: The owner shall not be charged
RANTY SERVICE: Warranty services or re-
for diagnostic labor which leads to the deter- pairs shall be provided at all POULAN/WEED
mination that a warranted part is defective if the EATER service centers. Call 1--800--554--6723.
diagnostic work is performed at an approved MAINTENANCE, REPLACEMENT AND RE-
POULAN/WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: POULAN/
PAIR OF EMISSION RELATED PARTS: Any
POULAN/WEED EATER approved replace-
WEED EATER may be liable for damages to ment part used in the performance of any war-
other engine components caused by the failure ranty maintenance or repair on emission related
of a warranted part still under warranty. WHAT parts will be provided without charge to the own-
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are CONTROL WARRANTY PARTS LIST: Car-
not covered. ADD--ON OR MODIFIED buretor, Ignition System: Spark Plug (covered
er if the part is under warranty. EMISSION
PARTS: The use of add--on or modified parts up to maintenance schedule), Ignition Module.
can be grounds for disallowing a warranty claim. MAINTENANCE STATEMENT: The owner is
POULAN/WEED EATER is not liable to cover responsible for the performance of all required
failures of warranted parts caused by the use of maintenance as defined in the instruction
add--on or modified parts. HOW TO FILE A manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
16
|