892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 1
ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 27
Instruction
manual
Double Insulated
7" Disc Sander
7" Polisher
MODEL 7401
7" Polisher
MODEL 7402
7" Disc Sander
IMPORTANT
To learn more about Porter-Cable
visit our website at:
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Part No. 892459-0011
Copyright © 2000 Porter-Cable Corporation
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 3
8. DRESS PROPERLY. Do not wear loose clothing or jewelry. Loose
clothing, draw strings and jewelry can be caught in moving parts. Rubber
gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
9. USE SAFETY GLASSES. Wear safety glasses or goggles while operating
power tools. Also face or dust mask if operation creates dust. All persons in
the area where power tools are being operated should also wear safety
glasses and face or dust mask.
10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect
from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged
or worn power cord and strain reliever replaced immediately. DO NOT
ATTEMPT TO REPAIR POWER CORD.
11. SECURE WORK. Use clamps or a vise to hold work. It’s safer than using
your hand and it frees both hands to operate tool.
12. DON’T OVERREACH. Keep proper footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better
and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool cords periodically and if damaged, have repaired by
authorized service facility. Inspect extension cords periodically and replace if
damaged. Have all worn, broken or lost parts replaced immediately. Keep
handles dry, clean and free from oil and grease.
14. DISCONNECT TOOLS when not in use, before servicing, and when
changing accessories such as blades, bits, cutters, etc.
15. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking
to see that keys and adjusting wrenches are removed from the tool before
turning it on.
16. AVOID UNINTENTIONAL STARTING. Do not carry a plugged-in tool with
finger on switch. Be sure switch is off when plugging in. Keep hands, body and
clothing clear of blades, bits, cutters, etc. when plugging in the tool.
17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use
only extension cords marked “Suitable for use with outdoor appliances – store
indoors when not in use.” If an extension cord is to be used outdoors it must
be marked with the suffix W-A following the cord type designation.
18. STAY ALERT. Watch what you are doing. Use common sense. Do not
operate tool when you are tired or while under the influence of medication,
alcohol or drugs.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine that it
will operate properly and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if
switch does not turn it on and off.
20. WEAR EAR PROTECTION to safeguard against possible hearing loss.
SAVE THESE INSTRUCTIONS
REPLACEMENT PARTS
When servicing use only identical replacement parts.
3
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 4
ADDITIONAL SAFETY RULES FOR DISC SANDERS & POLISHERS
1. ALWAYS disconnect the cord plug from the power circuit before
changing abrasive discs, pile fabric pad or lamb’s wool buff.
2. KEEP machine away from body while it is running.
3. MAKE SURE switch is in the “OFF” position before connecting tool to
power circuit.
4. NEVER use the spindle lock pin to stop the spindle from rotating.
5. MAKE SURE that discs, pads, etc., are in good condition, free of cracks
or chips and that RATED SPEED EXCEEDS THAT INDICATED ON THE TOOL
SPECIFICATION PLATE.
6. DO NOT install a grinding wheel on a sander or polisher. Grinding wheels
are hazardous if used without proper guarding.
7. USE PROPER SAFETY EQUIPMENT. Wear safety goggles to protect
your eyes and wear a protective mask to minimize breathing in the fine dust
created while sanding. NOTE: Some wood contains preservatives which can
be toxic. Take extra care to prevent inhalation and skin contact when working
with these materials.
8. SANDING OF LEAD BASED-PAINT IS NOT RECOMMENDED. Lead-
based paint should only be removed by a professional.
ADDITIONAL SAFETY RULES FOR PAINT REMOVAL
WARNING: Extreme care should be taken when removing paint. The
peelings, residue, and vapors of paint may contain lead, which is
poisonous. Exposure to even low levels of lead can cause irreversible
brain and nervous system damage; young and unborn children are
particularly vulnerable.
Before beginning any paint removal process you should determine whether
the paint you are removing contains lead. This can be done by your local
health department or by a professional who uses a paint analyzer to check for
lead.
LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL.
Persons removing paint should follow these guidelines:
1. KEEP THE WORK AREA WELL VENTILATED. Open the windows and put
an exhaust fan in one of them. Be sure the fan is moving air from inside to
outside.
2. REMOVE OR COVER any carpets, rugs, furniture, clothing, cooking
utensils and air ducts.
3. PLACE DROP CLOTHS in the work area to catch any paint chips or
peelings. Wear protective clothing such as extra work shirts, overalls and hats.
4. WORK IN ONE ROOM AT A TIME. Furnishings should be removed or
placed in the center of the room and covered. Work areas should be sealed
off from the rest of the dwelling by sealing doorways with drop cloths.
5. CHILDREN, PREGNANT OR POTENTIALLY PREGNANT women and
nursing mothers should not be present in the work area until the work is done
and all cleanup is complete.
6. WEAR A DUST RESPIRATOR or a dual filter (dust and fume) respirator
mask which has been approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of Safety and Health (NIOSH), or
4
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 5
the United States Bureau of Mines. These masks and replaceable filters are
readily available at major hardware stores. Be sure the mask fits. Beards and
facial hair may keep the masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.
7. KEEP FOOD AND DRINK out of the work area. Wash hands, arms, and
face and rinse mouth before eating or drinking. Do not smoke or chew gum or
tobacco in the work area.
8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors.
Use a wet cloth to clean all walls, sills and any other surfaces where paint or
dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high
phosphate detergent or trisodium (TSP) to wash and mop areas.
9. AT THE END OF EACH WORK SESSION put the paint chips and debris
in a double plastic bag, close it with tape or twist ties and dispose of properly.
10. REMOVE PROTECTIVE CLOTHING and work shoes in the work area to
avoid carrying dust into the rest of the dwelling. Wash work clothes separately.
Wipe shoes off with a wet rag that is then washed with the work clothes. Wash
hair and body thoroughly with soap and water.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.
CAUTION: Do not operate your tool on a current on which the
voltage is not within correct limits. Do not operate tools rated A.C.
only on D.C. current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix
W-A following the cord type designation. For example – SJTW-A to indicate
it is acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
NOTE: Wire sizes shown are AWG (American Wire Gage)
5
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 6
THE BASIC MACHINES
AUXILIARY HANDLE
An Auxiliary Handle is supplied with this tool and can be mounted on either
side of the gear housing. This handle should be used to give complete control
of the machine. Assemble handle to machine as follows:
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. Slide one of the washers (F) and then the hex spacer (B) onto the bolt (See
Fig. 1).
3. Place collar (C) over the hex spacer and position the bolt assembly to
either the left or right handle boss.
A Bolt
E
A
D
B Hex Spacer
C Collar
D Left Handle Boss
E Right Handle Boss
F Washer – 2
G Hex Nut
F
B
G
C
Fig. 1
4. Align and seat hex spacer into the hex socket of the handle boss.
5. Place the other washer onto bolt and secure with hex nut (G). Tighten
securely. (See Fig. 2).
A
F
A Bolt
C
C Collar
D Left Handle Boss
F Washer
D
G Hex Nut
F
G
Fig. 2
6. Thread auxiliary handle into collar. The handle and collar may be tightened
in any one of four positions (See Fig. 3). Move handle and collar to approximate
desired position and tighten securely.
6
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 7
1
2
3
4
Fig. 3
SWITCH
A trigger switch (A) Fig. 4, with lock button (B) Fig. 4, is conveniently located
in the machine handle. To start machine, depress switch trigger. To stop
machine, release trigger. If it is desired to keep machine running without
holding finger on trigger, depress trigger, push in on switch locking button in
left side of handle, and while holding button in, release trigger. To release
locking button, depress trigger and release.
CAUTION: ALWAYS MAKE SURE
SWITCH IS IN THE “OFF” POSITION
BEFORE CONNECTING MACHINE
TO THE POWER CIRCUIT.
VARIABLE SPEED
B
A
C
Speed is adjusted by turning the
thumbwheel, (C) Fig. 4. Thumbwheel
position #1 provides the slowest
operating speed (see chart) and
position #6 the fastest. Speed may be
changed while motor is running or while
it is stopped.
Fig. 4
Model
7401
Low Speed
1500 RPM
3300 RPM
High Speed
2000 RPM
4500 RPM
7402
7
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 8
SPINDLE LOCK
A spindle lock (A) Fig. 5 is
located on the right side of the
gear case. To Operate: Depress
spindle lock pin with thumb
while rotating spindle (B) BY
HAND until pin engages and
stops spindle rotation.
B
CAUTION: Do not depress
spindle lock while tool is
running.
A
Fig. 5
THE DISC SANDER
TO INSTALL SANDING DISC
The Porter-Cable sander has a wrenchless type backup pad and locknut. No
wrenches are required to install or remove sanding disc.
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. Depress spindle lock pin (see Fig. 6) and rotate back-up pad clockwise
onto spindle until it seats. Then rotate the flexible disc onto shaft until it seats.
3. Place retaining nut through hole in sanding disc and rotate clockwise onto
shaft until it seats. Normal operation of the Sander will tighten the sanding
disc.
4. To remove sanding disc, disconnect machine from power source, depress
spindle lock pin and rotate sanding disc together with the flexible disc
counterclockwise and remove.
A
C
E
D
B
F
Fig. 6
A Spindle Lock Pin
B Spindle
C Back-up Pad
D Flexible Disc
E Sanding Disc
F Retaining Nut
8
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 9
USING DISC SANDER
1. CAUTION: Secure work to prevent it from moving during the sanding
operation. Friction between the sanding disc and work will try to spin work
away from sander and may cause bodily injury.
2. CAUTION: Wear safety glasses and dust mask.
3. Hold sander firmly by the rear and auxiliary handles, making sure sanding
disc is clear of work and foreign objects. Start sander and lower at an angle
so that approximately 1" to 11/4" of the sanding disc contacts the work (see
Fig. 7). Too great an angle may result in gouging or snagging the work, while
too small an angle results in extreme difficulties in controlling the sander.
Fig. 7
4. Move sander in long sweeping overlapping strokes as you go back and
forth. Do not move sander in a circular motion or stay in one spot too long as
this will produce swirls and an uneven finish. The weight of the sander applies
sufficient pressure for fast stock removal. Additional pressure will only slow
the sander down and decrease removal of stock.
5. Lift sander from work before turning off motor.
6. Always be sure motor has stopped before setting sander down.
7. For rough sanding and quick stock removal, use a coarse grit sanding
disc. For a fine finish, use a medium grit disc, followed by a fine grit disc. Do
not go directly from a coarse grit to a fine grit, as it is difficult to remove marks
left by the coarse grit disc.
THE POLISHER
TO INSTALL POLISHING PAD
The Porter-Cable Polisher has a “Hook and Loop” style back-up pad and
buffing pad. A “Hook and Loop” compounding pad is available as an
accessory (see list in back of this manual). No wrenches are required for
installation or removal.
1. CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
2. Depress spindle lock pin (see Fig. 8) and rotate back-up pad clockwise
onto spindle until it seats.
3. Align the buffing pad (or the accessory compounding pad) with the back-
up pad and press in place firmly.
9
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 10
C
A
D
B
Fig. 8
A Spindle Lock Pin
B Spindle
C Back-up Pad
D Buffing Pad
4. TO REMOVE: DISCONNECT TOOL FROM POWER SOURCE, grasp
edge of the buffing pad (or compounding pad) and “peel” away from back-
up pad, engage spindle lock pin and rotate back-up pad counterclockwise to
remove.
USING POLISHER
1. If item to be polished is light enough to be moved by the rotating
polishing pad, it should be securely anchored to prevent possible bodily
injury.
2. Hold polisher firmly by the rear and auxiliary handles, making sure
polishing pad is clear of work and foreign objects. Start polisher and lower at
an angle so that approximately 1/2 or slightly less of the polishing pad
contacts the work.
3. Move polisher in long continuous sweeping strokes. DO NOT HOLD
POLISHER IN ONE SPOT as this will create heat and possibly damage
surface being polished.
4. Lift polisher from work before turning off motor.
5. Always be sure motor has stopped before setting polisher down.
POLISHING TIPS
USE ONLY QUALITY POLISH MADE FOR POWER POLISHING
APPLICATION and apply per manufacturer’s instructions.
For best results, thoroughly clean surface to be polished.
When polishing automobiles, wash the car thoroughly to remove dust, dirt
and other abrasives that may scratch the finish.
Buffs or pads may become gummed up after a period of use. They may be
washed out with soap and water. Shake out as much water as possible and
then spin dry on machine. Do this in an area where you will not splatter
articles.
10
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 11
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with compressed air. Remove buildup
of grime resulting from working with green or sappy woods. All plastic parts
should be cleaned with soft cloths. NOTE: Never use solvents to clean plastic
parts. Plastics can be easily damaged by such solvents.
CAUTION: Wear safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug
are making good contact in the outlet. Also, check for blown fuses or open
circuit breakers in the line.
BRUSH INSPECTION AND LUBRICATION
At approximately 100 hours of use, take or send your tool to your nearest
Authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected; worn parts replaced, when necessary; relubricated with fresh
lubricant, if required; reassembled with new brushes; and performance
tested.
Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE
TOOL UNDER THIS CONDITION. If proper operating voltage is present,
return your tool to the Service Station for immediate service.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE
CENTER. All repairs made by these agencies are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or
attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
11
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 12
ACCESSORIES
The testing of this tool has been accomplished with the use of the following
accessories ONLY. For safest operation, it is recommended that ONLY these
accessories be used with this product.
WARNING: Since accessories other than those listed have not been
tested with this product, use of such accessories could be
hazardous.
FOR DISC SANDER ONLY
55741 7" Abrasive Back-Up Kit
55747 Replacement Abrasive Retaining Nut
FOR POLISHER ONLY
54740 “Hook & Loop” Back-Up Pad
54741 “Hook & Loop” Polishing Pad
54742 “Hook & Loop” Compounding Pad
POWER PAINT REMOVER
ACCESSORIES
Tungsten Carbide Discs
All 6" diameter
No. 18024 – #46 grit
No. 18027 – #36 grit
No. 18030 – #24 grit
No. 18018
Sponge Rubber Back-Up Pad
No. 48233
Spanner Wrench for 48235 Nut
PORTER-CABLE LIMITED ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, P.O. Box 2468, Jackson, Tennessee 38302-2468; Attention: Product Service.
THE FOREGOING OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY
IMPLIED WARRANTY AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how
long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
12
892459 - 11-30-00.QXD 2/25/02 8:23 AM Page 40
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Power Tools are Available at These Locations
•Delta)
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
MINNESOTA
OREGON
ARIZONA
GEORGIA
Minneapolis 55429
4315 68th Avenue North
Phone: (612) 561-9080
Fax: (612) 561-0653
Portland 97230
4916 NE 122 nd Ave.
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
Phone: (503) 252-0107
Fax: (503) 252-2123
Phone: (602) 437-1200
Fax: (602) 437-2200
ILLINOIS
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
MISSOURI
PENNSYLVANIA
North Kansas City 64116
1141 Swift Avenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
CALIFORNIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
St. Louis 63119
TENNESSEE
Nashville 37214
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
2262 Lebanon Pike
Phone: (615) 882-0320
Fax: (615) 882-0051
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NEW YORK
COLORADO
Denver 80216
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
TEXAS
Carroliton 75006 (Dallas)
5855 Stapleton Drive North
Suite A-140
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (303) 370-6909
Fax: (303) 370-6969
NORTH CAROLINA
Charlotte 28270
Houston 77055
FLORIDA
Phone: (781) 848-9810
Fax: (781) 848-6759
9129 Monroe Road, Suite 110
Phone: (704) 841-1176
Fax: (704) 708-4625
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
Phone: (954) 321-6635
Fax: (954) 321-6638
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
WASHINGTON
Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: (425) 251-6680
Fax: (425) 251-9337
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Cleveland 44125
8001 Sweet Valley Drive Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 901-541-6042 for assistance locating one. Parts
and accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized
Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will
be directed to the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en
muchas grandes ciudades. Llame al 800-487-8665 ó al 901-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los
accesorios para los productos Porter-Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable
Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas
opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service
agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 901-541-6042 pour obtenir de l’aide pour en
repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable Delta, s’adresser à tout distributeur Porter-Cable
Delta, centre de service agréé ou centre de service d’usine Porter-Cable Delta. Si vous n’avez accès à aucun de ces centres, appeler le
888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable Delta le plus proche.
•
•
•
•
·
•
•
•
•
•
•
•
CANADIAN SERVICE CENTERS
ALBERTA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
MANITOBA
QUÉBEC
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
1515 Ave.
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
505 Southgate Drive
Guelph, Ontario
N1H 6M7
1447, Begin
St-Laurent, (Montréal), Québec
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
Phone: (519) 836-2840
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
·
DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA
S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE
·
DELTA Corporation): BAMMER®, LASERLOC®, OMNIJIG®,
POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®, QUICKSAND®, SANDTRAP®, SAW BOSS®, SPEED-BLOC®,
SPEEDMATIC®, SPEEDTRONIC®, STAIR-EASE®, THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, TIGER CUB®, TIGER SAW®,
TORQ-BUSTER®, VERSA-PLANE®, WHISPER SERIES®, DURATRONIC™, FRAME SAW™, INNOVATION THAT WORKS™, JETSTREAM™,
MICRO-SET™, MORTEN™, NETWORK™, RIPTIDE™, TRU-MATCH™, WOODWORKER’S CHOICE™.
Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países. Marques déposées, indiquées par la lettre ®, sont déposées au Bureau des brevets d’invention et marques
déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A.
|