ESPAÑOL: PÁGINA 14
FRANÇAISE : PAGE 30
Instruction
manual
Belt Sanders
MODEL 360
3" x 24"
MODEL 362
4" x 24"
MODEL 360VS
3" x 24"
MODEL 362VS
4" x 24"
MODEL 361
3" x 24"
MODEL 363
4" x 24"
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2004 Porter-Cable Corporation
Part No. 899713 - 10-27-04
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,could result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in
property damage.
CALIFORNIA PROPOSITION 65
Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known (to the
State of California) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
●
●
●
lead from lead-based paints
crystalline silica from bricks and cement and other masonry products
arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
3
GENERAL SAFETY RULES*
Read all instructions Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury. The term "power tool" in all of the warnings listed
below refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock
b) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
4
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
continued
GENERAL SAFETY RULES*
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance
with these instructions and in the manner intended for the
particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the
power tool is maintained.
5
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
SPECIFIC SAFETY RULES AND SYMBOLS
1.
Hold tool by the insulated gripping surfaces when
performing an operation where the cutting tool may contact hidden
wiring or its own cord. Contact with a “live” wire will make exposed metal
parts of the tool “live” and shock the operator.
2. Use proper safety equipment. Wear safety goggles for eye protection,
wear hearing protection, and wear a protective mask to minimize breathing
in the fine dust created while sanding.
3. Sanding of lead-based paint is not recommended. Lead-based paint
should only be removed by a professional.
4. Always maintain a firm grip on the belt sander handles with both hands to
prevent loss of control.
5. Do not operate belt sander without all guards and covers securely in
place.
6. Wear eye and hearing protection. Always use safety glasses. Everyday
eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.
Eye protection equipment should comply with ANSI Z87.1 standards.
Hearing equipment should comply with ANSI S3.19 standards.
7. Take precautions against dust inhalation. The dust generated by certain
woods and wood products can be injurious to your health. Always operate
machinery in well-ventilated areas, and provide for proper dust removal.
Use wood dust collection systems whenever possible. Also, use face or
dust mask if cutting operation is dusty. Dust mask protection should
comply with MSHA/NIOSH certified respirator standards. Splinters, air-
borne debris, and dust can cause irritation, injury, and/or illness.
8. Some wood contains preservatives which can be toxic. Take extra care
to prevent inhalation and skin contact when working with these materials.
Request and follow any safety information available from your material
supplier.
6
SYMBOL
DEFINITION
........................ volts
V
A
........................ amperes
........................ hertz
........................ watts
........................ kilowatts
........................ farads
........................ microfarads
........................ litres
Hz
W
kW
F
µF
l
g
........................ grams
........................ kilograms
........................ bars
........................ pascals
........................ hours
........................ minutes
........................ seconds
........................ no-load speed
kg
bar
Pa
h
min
s
n0
…/min or …min 1 ......... Revolutions or reciprocations per minute
-
or d.c. ................ direct current
or a.c. ................ alternating current
2
........................ two-phase alternating current
2N
3
........................ two-phase alternating current with neutral
........................ three-phase alternating current
3N
........................ three-phase alternating current with neutral
........................ rated current of the appropriate fuse-link in amperes
........................ time-lag miniature fuse-link where X is the symbol
for the time/current characteristic, as given in IEC 60127
........................ protective earth
........................ class II tool
........................ IP symbol
IPXX
7
ADDITIONAL SAFETY RULES FOR PAINT REMOVAL
Extreme care should be taken when removing paint. The
peelings, residue, and vapors of paint may contain lead, which
is poisonous. Exposure to even low levels of lead can cause
irreversible brain and nervous system damage. Young and
unborn children are particularly vulnerable.
Before beginning any paint removal process you should determine whether the
paint you are removing contains lead. This can be done by your local health
department or by a professional who uses a paint analyzer to check for lead.
Lead-based paint should only be removed by a professional.
Persons removing paint should follow these guidelines:
1. Keep the work area well ventilated. Open the windows and put an
exhaust fan in one of them. Be sure the fan is moving air from inside to outside.
2. Remove or cover any carpets, rugs, furniture, clothing, cooking
utensils, and air ducts. Such preventive safety measures reduce the risk of
exposure.
3. Place drop cloths in the work area to catch any paint chips or peelings.
Wear protective clothing such as extra work shirts, overalls and hats. Such
preventive safety measures reduce the risk of exposure.
4. Work in one room at a time. Furnishings should be removed or placed in
the center of the room and covered. Work areas should be sealed off from the
rest of the dwelling by sealing doorways with drop cloths.
5. Children, pregnant, or potentially pregnant women and nursing mothers
should not be present in the work area until the work is done and all
cleanup is complete. Such preventive safety measures reduce the risk of
injury.
6. Wear a dust respirator or a dual filter (dust and fume) respirator mask
which has been approved by the Occupational Safety and Health
Administration (OSHA), the National Institute of Safety and Health (NIOSH),
or the United States Bureau of Mines. These masks and replaceable filters are
readily available at major hardware stores. Be sure the mask fits. Beards and
facial hair may keep the masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.
7. Keep food and drink out of the work area. Wash hands, arms, and face
and rinse mouth before eating or drinking. Do not smoke or chew gum or
tobacco in the work area.
8. Clean up all removed paint and dust by wet mopping the floors. Use a
wet cloth to clean all walls, sills and any other surfaces where paint or dust is
clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate
detergent or trisodium (TSP) to wash and mop areas.
9. At the end of each work session, put the paint chips and debris in a
double plastic bag, close it with tape or twist ties and dispose properly. Such
preventive safety measures reduce the risk of exposure.
10. Remove protective clothing and work shoes in the work area to avoid
carrying dust into the rest of the dwelling. Wash work clothes separately. Wipe
shoes off with a wet rag, then wash that rag with the work clothes. Wash hair and
body thoroughly with soap and water.
SAVE THESE INSTRUCTIONS!
8
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown on
the specification plate on the tool. Several models, however, are designed for
A.C. current only. Refer to the specification plate on your tool for proper voltage
and current rating.
Do not operate your tool on a current on which the voltage is not
within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors, it must be marked with the suffix W-
A or W following the cord type designation. For example – SJTW-A to indicate it
is acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft.
250 Ft. 300 Ft.
500 Ft. 600 Ft.
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Belt Sanders are designed for smoothing rough boards, removing
old paint and varnish, fine-surfacing wood, metal, plastics and other materials.
9
ASSEMBLY
NOTE: This tool is shipped completely assembled. No assembly time or
tools are required.
INSTALLING AND REMOVING THE ABRASIVE BELT
DISCONNECT TOOL FROM POWER SOURCE.
1. Place the sander on its left side.
2. Pull the lever (A) out toward the
rear of the tool to retract the idler
pulley and release tension on the
abrasive belt.
B
A
3. Remove the old belt.
4. Install the new belt with the arrow
(printed on the inside of the belt)
on the top and pointing TOWARD
the idler pulley (B).
Fig. 1
NOTE: Some sanding belts are bi-directional and will not have arrows printed on
them. You can install them to run in either direction.
5. Engage the front pulley by pushing the lever (A) back to its original position.
OPERATION
TO START AND STOP BELT SANDERS
1. Make sure that the switch is “OFF” and the power circuit voltage is the same
as the voltage shown on the specification plate. Connect the tool to the
power circuit.
2. Squeeze the trigger (A) Fig. 2 to
C
start the motor. Release the
trigger to stop the motor.
B
3. To allow the motor to run without
constantly holding the trigger,
press the trigger switch (A), push
the lock button (B) Fig. 2, and
release the trigger switch.
A
4. To release the lock button,
squeeze the trigger and release.
Fig. 2
VARIABLE SPEED CONTROL (Models 360VS and 362VS Only)
Models 360VS and 362VS have Variable Speed Control. The operating speed is
adjustable between 1000 SFM (surface feet per minute) and 1500 SFM.
Adjust the speed by turning the thumbwheel (C) Fig. 2. Thumbwheel position #1
provides the slowest operating speed (1000 SFM) while position #6 provides the
fastest operating speed (1500 SFM). The speed can be changed with the motor
running or not running.
10
TRACKING THE ABRASIVE BELT
To prevent excessive wear on both the sander and belt, NEVER allow the
abrasive belt to rub on the sander frame. To make sure that the belt is tracking
correctly, do the following:
Make sure that the trigger is in the “OFF” position before
connecting the tool to the power circuit.
1. Turn the tool over, rest the tool on
its front handle, and grasp the
rear handle with your left hand .
A
Rest your ring finger and little
finger on the trigger (Fig. 3).
2. Start the motor by squeezing the
trigger.
3. Turn the belt aligning screw (A)
Fig. 3 in either direction until the
edge of the belt is even with the
outer edge of the rear rubber-
Fig. 3
covered pulley. The edge of the belt will extend beyond the edge of the
front pulley.
4. Turn the motor “OFF” and allow the sander to come to a COMPLETE STOP
before turning it right side up.
ATTACHING AND CARE OF DUST BAG
Models 360, 360VS, 362 and 362VS
Depress the dust bag spring clips
(A) Fig. 4, and place the dust bag
spring (A) between the ridges on
the spout (B).
A
For most efficient operation, empty
the dust bag when it is half full. To
remove, squeeze the dust bag
spring clips (A) and pull the bag
straight up. Unzip the rear of the
bag and shake out the dust. Every
so often, turn the bag inside out and
brush the accumulated dust from
the inside.
B
Fig. 4
Do not operate the sander without a dust bag or a dust collection
hose.
11
SELECTING AN ABRASIVE BELT
The principle abrasive materials used on belts for machine sanding are aluminum
oxide and silicon carbide. Aluminum oxide is the softer of the two, but is tougher
and more suited for woods and soft (non-ferrous) metals. Silicon carbide is
extremely hard and is best suited for surfacing stone, marble, and glass.
Abrasives are classed as open-coated (with grits spaced apart), or closed-
coated (with grits close together). Closed coatings provide hard, fast cutting
action for hardwoods and dense metals, while open coatings are more suited to
soft materials and painted surfaces.
To obtain the best finish, start with a “COARSE” grade of abrasive and change
to “MEDIUM” and then to“FINE” as work progresses.
GENERAL SANDING
SECURE THE WORKPIECE and maintain a FIRM GRIP on the
sander. Movement of the sanding belt against the workpiece
will try to move the work backward and/or the sander forward.
Verify that the switch is “OFF” before connecting the sander to
the power circuit.
1. Hold the sander off the work before starting the motor.
2. Lower the sander to the work, touching the rear part of the belt first. Level
the machine when moving it forward.
3. Guide the machine over the work in overlapping strokes. Allow the sander
to do the work.
4. Avoid applying excessive pressure. The weight of the machine is usually
sufficient for a fast smooth finish. A slight increase in pressure may speed
removal of material, but too much pressure will slow the motor and
decrease removal.
5. Work back and forth over a fairly wide area to obtain an even surface.
6. Do not let the tool tilt. The edge of the belt can make a deep cuts into the
surface.
7. Do not pause in any one spot during the sanding operation. The belt will eat
into the work and make the surface uneven.
8. Lift the tool from the work before turning the motor off.
9. Always be sure that the motor has completely stopped before putting the tool
down.
FAST SANDING ON ROUGH WORK
To smooth a rough surface quickly, use a coarse grit abrasive belt. With the belt
positioned diagonally across the grain, move the tool in the direction of the grain
(Fig. 5).
Overlap the strokes and cover the
entire surface, working from both
sides of the board (angle left and then
angle right.) Smooth the surface by
guiding the sander back and forth
with the grain. Change the belt to a
medium grit and follow the same
procedure.
Finish by thoroughly working the grain
lengthwise. Change again to a fine
Fig. 5
grit and repeat. Always finish sanding
with the grain.
12
REMOVING OLD PAINT AND VARNISH
Read and follow “ADDITIONAL SAFETY RULES FOR PAINT
REMOVAL” section of this manual.
Your sander is an excellent tool for removing old paint and varnish from flat
surfaces. However, two problems are common: 1) sanding material that loads
the abrasive and, 2) friction heat caused by working too long in one place. To
overcome the loading problem, use a coarse grit open coat abrasive belt and a
single stroke action. Overheating can be avoided by using a fairly quick stroke
and moving to another area quickly. A piece of felt about 1/4" thick can be
inserted under the shoe for fast spot sanding and for working on stubborn areas
of paint and varnish
SPECIAL SANDING PROCEDURES
Generally, the operator should sand with a back and forth motion. Some
materials and some types of operations, however, require a different technique.
In rough sanding, use the tool at an angle. In spot sanding, use the tool with only
the front pulley touching the surface (especially useful in smoothing excess glue
from wood joints). On metals, slate, marble, or plastic materials, sanding can be
done in all different directions because of a lack of grain.
DOORS AND MILL WORK
When sanding doors, cabinet frames, sash, storm windows and screens, take
care to avoid working into the cross grain where one member meets another.
Notice that the right edge of the belt is visible on the sander. Work carefully
along the edge where the rail meets the stile. If the joint is slightly uneven, use a
fine abrasive and very light sanding pressure to smooth it before making
finishing runs.
For lengthy work on walls or other vertical surfaces, balance the tool with a
length of sash cord, two small pulleys, a light wood frame, and a weight that is
the same as, or slightly less than, the weight of the sander. The frame consists of
two pieces leaning against a wall with a third piece nailed to their top ends. The
two pulleys are located so that the weight on one end of the cord will be out of
the way, but will balance the sander fastened to the other end. When starting
vertical work, angle the sander so you can see that the belt makes contact with
the material. As the belt touches, level the machine and make the stroke away
and to the left. This movement will offset the tendency to cut heavily into the
work at the start of the stroke.
GOOD SANDING TECHNIQUE
Getting to know the sander is most important in obtaining smooth results with a
minimum of labor. Operators will quickly learn how to start a stroke with a
sweeping motion to produce the best results. Use a long even stroke without
additional pressure on the tool. Overlap each stroke and vary the length of
movement so the results will be even. Always lift the tool from the work before
starting and stopping the motor.
13
BE CAREFUL when sanding at the end of a board. Keep the tool level and flat on
the work surface. Don’t let the front of the tool drop. (Fig. 6). If this happens, it will
round the edge.
Fig. 6
Your sander will work very fast and can do a thorough job in a fraction of the time
required by hand sanding. Do not rush the job. Give every surface a thorough
sanding with each grade of abrasive before changing to finer grits. Always use the
abrasive material and grit size recommended for the particular job.
SANDING METAL
Use the Belt Sander to obtain a grained satin finish on metal. A special graphite
pad is available to replace the steel shoe on the bottom of the sander. The
softness of this pad aids in blending the graining. The pad is the proper length
for sanders using a 3" x 24" belt. For sanders using shorter belt lengths, cut the
pad so that it is the same length as the steel shoe. Replace the steel shoe with
the graphite pad.
TROUBLESHOOTING GUIDE
list of service centers or call the Porter-Cable help line at 1-800-487-8665.
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic
parts. They could possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are
making good contact in the outlet. Also, check for blown fuses or open circuit
breakers in the line.
14
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No further lubrication is
necessary.
FRAME PROTECTOR
The frame protector bar is made of hardened steel. It is located to the left and
the rear of the idler pulley and is fastened to the frame. This bar protects the
frame of the tool when tracking the abrasive belt. Adjust the belt so that it moves
evenly across (without rubbing) the protective bar. When this bar becomes worn
and uneven, replace it with a new one (available from your Porter-Cable Service
Center).
DRIVE PULLEY
The rubber-covered drive pulley at the rear of the tool is crowned or tapered
from the center to either side to make the abrasive belt run true and in line with
the idler pulley at the front of the tool. After considerable use, the crown will wear
away and the belt will begin to run off the side of the pulley and cut into the
guide block or frame. When the crown is worn to this extent, have the drive
pulley replaced by your Authorized Porter-Cable Service Station. This action can
be checked each time the abrasive belt is replaced and tracked. After the belt is
tracked to the front pulley, watch it for a few seconds to see that it runs true and
stays in place on the back pulley. Avoid getting oil and grease on the rubber
cover. It will cause it to fail.
BRUSH INSPECTION
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY
SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes
installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your tool
to the service station for immediate service.
Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
15
SERVICE
REPLACEMENT PARTS
When servicing use only identical replacement parts. For a service parts list or to
learn more about Porter-Cable visit our website at www.porter-cable.com
SERVICE AND REPAIRS
All quality tools will eventually require servicing, or replacement of parts due to
wear from normal use. For assistance with your tool, visit our website at
www.porter-cable.com for a list of service centers or call the Customer Care
Department at 1-800-487-8665. All repairs made by our service centers are fully
guaranteed against defective material and workmanship. We cannot guarantee
repairs made or attempted by others.
Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta
Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-Cable
Authorized Service Stations. Please visit our Web Site www.porter-cable.com
for a catalog or for the name of your nearest supplier.
Since accessories other than those offered by Porter-
Cable•Delta have not been tested with this product, use of
such accessories could be hazardous. For safest operation,
only Porter-Cable•Delta recommended accessories should
be used with this product.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
16
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
GEORGIA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
OREGON
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
ILLINOIS
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
PENNSYLVANIA
St. Louis 63119
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Diego 92111
7638 Clairemont Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
NEW YORK
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MARYLAND
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
COLORADO
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
FLORIDA
WASHINGTON
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
•
•
•
•
•
•
•
•
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
7.2-PTG-F-1
|