INSTALLATION INSTRUCTIONS FOR PART 95-3528
APPLICATIONS
PONTIAC GTO
2004-2006
95-3528
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Brackets • B) Double DIN Trim plate
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• 86-3528 Radio Removal Keys
1-800-221-0932
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION
95-3528 DASH DISASSEMBLY
PONTIAC GTO 2004-2006
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Using the radio removal keys, pull the
factory radio from the dash and dis-
connect the wiring. (Figure A)
3
4
5
Unsnap and remove the trim panel at
the top center of the dash above the
A/C vents and remove (4) Phillips
screws. (Figure B)
B
Remove (1) Phillips screw from inside
lower open storage area where
center console and dash meet.
(Figure C)
Unsnap and remove center console
(open center armrest/ storage com-
partment and work forward). (Figure D)
Continue on page 2.
C
D
1
95-3528 DASH DISASSEMBLY
PONTIAC GTO 2004-2006
E
6
Remove (2) Phillips screws exposed
at the bottom of the center panel sur-
rounding radio and remove panel.
(Figure E)
7
8
Unclip and remove trim panel sur-
rounding radio and A/C controls.
Remove (3) Phillips screws holding
"cage" in radio opening. (Figure F)
9
Pull down on the "cage" from the
opening inside on the top and
remove. (Figure G)
F
Continue to final assembly.
G
2
95-3528 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the Double DIN brackets to the
Double DIN radio unit using the screws
supplied with the radio. (Figure A)
1
Continue to final assembly.
3
95-3528 KIT ASSEMBLY
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the Double DIN brackets to the
stacked ISO mount units using the
screws supplied with the units.
(Figure A)
1
Continue to final assembly.
4
95-3528 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
C
D
D) Tape
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Insert and secure the radio/bracket assembly into the radio opening using the
screws removed in step 8 of disassembly.
Snap the Double DIN trim plate onto the bracket/radio assembly.
Reassemble in reverse order of disassembly.
4
5
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
95-3528 INSTRUCTIONS
1-800-221-0932
REV. 05/07/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST95-3528
|