Polaroid Flat Panel Television FCM 0700A User Manual

7” Under-the-Counter LCD  
FCM-0700A  
Operating Manual  
 
Important Safety Instruction  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT  
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lightning flash with arrowhead symbol, within an equilateral triangle,  
is intended to alert the user to the presence of uninsulated “dangerous  
voltage” within the product’s enclosure that may be of sufficient  
magnitude to constitute a risk of electric to persons.  
The exclamation point within an equilateral triangle is intended to alert the  
user to the presence of important operating and maintenance (servicing)  
instructions in the literature accompanying the appliance.  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.  
POWER SUPPLY:  
Connect the supplied adapter to the side of the DVD player in the slot marked “Power  
In”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you have  
difficulty inserting the plug, turn it over and reinsert it, if the unit will not be used for a  
long time, disconnect the plug from the outlet.  
NOTE:  
Before plugging the power cord into an AC outlet, make sure that all the connections  
have been made.  
CAUTION: These servicing instructions are for use by qualified service personnel only.  
To reduce the risk of electric shock, do not perform any servicing other than that  
contained in the operating instructions unless you are qualified to do so.  
Refer to service manual for servicing instructions.  
 
-3-  
Important Safety Instruction  
Notes:  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Maintain well ventilated conditions around  
the product. Do not put product on bed, sofa or anything that blocks ventilation.  
Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A  
polarized plug has two blades with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide blade or the third prong is  
provided for your safety. If the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table specified  
by the manufacturer, or sold with the apparatus. When a cart is  
used, use caution when moving the cart/apparatus combination  
to avoid injury from tip-over.  
13. Unplug this apparatus during lightning storms or when unused for long periods of  
time.  
14. Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or has  
been dropped.  
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with  
liquids, such as vases, shall be placed on the apparatus.  
Copyright Protection  
Unauthorized copying, broadcasting, public performance, and lending of disks are  
prohibited. This product incorporates copyright protection technology that is protected  
by method claims of certain U.S. patents and other intellectual property rights owned  
by Macrovision Corporation and other rights owners. Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and is intended for home  
and other limited viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is prohibited.  
 
-4-  
FCC Notice  
Note: This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following  
measures:  
-- Reorient or relocate the receiving antenna.  
-- Increase the separation between the equipment and receiver.  
-- Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
-- Consult the dealer or an experienced radio/TV technician for help.  
 
-5-  
Characteristic Features  
This product has incorporated LCD  
display, TV receiver and radio function  
in one system. It is designed for  
convenient use in the kitchen; please  
refer to page 21 for the installation  
instructions.  
TV Functions  
Receive TV signal clearly.  
Search for TV channels automatically.  
Memorize the channels automatically.  
Radio Functions  
Receive AM/FM signal clearly.  
Search for radio stations automatically.  
Store radio stations easily.  
Search for radio stations in high or low  
frequency range.  
Multiple Mode  
TV mode  
Radio function  
External Audio/Video Input mode  
High Quality Properties  
Screen  
Support the picture of normal screen (4:3)  
and wide screen (16:9).  
AV Input  
External Audio/Video input can be  
connected to most external AV sources.  
LCD (Liquid Crystal Display)  
Color LCD screen clearly shows data.  
Amplifier Function  
Built-in 2x2.5w stereo amplifier and left  
and right speakers.  
Switching Power Adapter  
Automatically adapts to voltage required.  
 
-6-  
Front Panel  
Front Panel Drawing  
1. POWER button  
Press to access to or exit the STANDBY  
mode.  
10. SEEK + button  
Under radio mode, press once to fine  
tune frequency forward. Press for about  
1.5 seconds to search radio stations  
forward automatically.  
2. TV button  
Press to enter TV mode. Or under TV  
mode, press to display the current  
channel number on the display panel.  
3. FM button  
Press to enter FM radio mode.  
4. AM button  
Press to enter AM radio mode.  
5. AV button  
Press to enter external AV input mode.  
6. 16:9/4:3 button  
Press to shift the aspect radio between  
16:9 and 4:3.  
7. Remote Sensor  
Receives remote control signal for  
operation.  
11. MUTE button  
Press to turn on or off the speaker  
output. The corresponding information  
will be displayed on the display panel.  
12. TIME button  
Press it once to display the time on the  
display panel. In standby status, the time  
is still displayed on the panel.  
Press it again to set the time on the  
display panel. Use the ꢀꢁbuttons to  
select the editing position of hour or  
minute, and then use the ꢂꢃ buttons to  
adjust the value of the hour or minute  
upward and downward.  
13. SET button  
Press to enter and exit from the timer  
setup menu. Or Press to memorize the  
station under AM/FM status.  
14. ▲  
Press to select items in the setup menu.  
Press to select channels or radio  
stations forward under TV or radio mode.  
Press to adjust the value upward when  
setting the time on the display panel.  
15. OK button  
8. Display panel  
Display the time, status, radio frequency  
and radio station number.  
When adjusting volume, the VOL and  
volume level will be displayed on the  
display panel for several seconds.  
9. SEEK – button  
Under radio mode, press once to fine  
tune frequency backward. Press for  
about 1.5 seconds to search radio  
stations backward automatically.  
Press to confirm selections in setup  
menu.  
 
- 7 -  
Rear Panel and display panel  
16.  
Press to adjust the value downward  
Press to select items in the setup menu.  
Or press to increase the volume. Or  
press to increase the value in the picture  
setup menu.  
17. MENU button  
Press to enter the system setup menu.  
18. ▼  
when setting the time on the display  
panel.  
19.  
Press to select items in the setup menu.  
Or press to decrease the volume. Or  
press to decrease the value in the  
picture setup menu.  
Press to select items in the setup menu.  
Press to select the channels or radio  
stations backward under TV or radio  
mode.  
20. LCD screen  
Present high resolution picture.  
Rear Panel Drawing  
1. ANT INPUT jack  
4. Left/Right AUDIO input jack  
Connection for audio input.  
5. VIDEO input jack  
Connection for video input.  
6. Direct current 12V input jack  
Connected to external antenna to  
receive the TV program in TV mode.  
2. FM 75Ωcoaxial antenna jack  
3. AM antenna jack  
Display Panel Drawing  
1. FM radio status indicator  
2. AM radio status indicator  
AM time indicator  
5. Minute or character indicators  
6. Character indicators  
7. FM frequency unit of MHz indicator  
3. PM time indicator  
4. Hour or character indicators  
8. AM frequency unit of KHz indicator  
 
- 8 -  
Remote Control  
Preparation  
Use Of Remote Control  
Refer to the drawing, and remove the  
empty battery receptacle.  
Please directly point the r/c towards the  
main unit when operating. The r/c works  
properly in a distance below 7m and at  
an angle of up to 60°to the front of the  
unit. No obstacles may stand in the way  
between r/c and infrared sensor.  
Insert the battery into the receptacle,  
please make sure the polarity matches  
the marks inside the component.  
The batteries normally last for about six  
months, although this depends on how  
often, and for what operations the  
remote control is used.  
Insert the receptacle into the remote  
control.  
If the remote control unit fails to work  
even when it is operated near the player,  
replace the batteries.  
If the r/c is not used for a long period of  
time, please remove the batteries from  
the compartment, to prevent damages  
by leakage.  
 
- 9 -  
Remote Control  
Remote Control Drawing  
1. POWER button  
4. AM button  
Press to access to or exit from the  
STANDBY mode.  
Press to shift to AM signal input mode.  
5. AV button  
2. TV button  
Press to shift to external AV input mode.  
Press to enter TV mode.  
6. MENU button  
3. FM button  
Press to enter the system setup menu.  
Press to shift to FM signal input mode.  
 
- 10 -  
Remote Control  
7. OK button  
13. 0-9 number buttons  
Select numbers by pressing these  
buttons.  
Press to confirm selections.  
8. ꢀꢁꢂꢃ  
14. SEEK +/- button  
Press to select menu items or settings.  
Press ꢀꢁ buttons to adjust volume. Or  
press to adjust value in the picture setup  
menu.  
Under radio mode, press once to fine  
tune frequency forward or backward.  
Press for about 1.5 seconds to search  
radio stations forward or backward  
automatically.  
Press ꢂꢃ buttons to select channels or  
radio stations forward and backward in  
TV or radio mode. Or press to adjust the  
value of time when setting time on the  
display panel.  
15. SET button  
Press to enter and exit from the timer  
setup menu. Or Press to memorize the  
station under AM/FM status.  
9. TIME button  
Press it once to display the time on the  
display panel. In standby status, the time  
is still displayed on the display panel.  
Press it twice to set the time on the  
display panel. Use the ꢀꢁbuttons to  
select the editing position of hour or  
minute, use the ꢂꢃ buttons to adjust  
the value of the hour or minute upward  
and downward.  
16. 16:9/4:3 button  
Press to shift the aspect radio between  
16:9 and 4:3.  
17. LCD ON/OFF button  
Press to turn on or off the LCD screen  
display under TV and AV mode.  
18. CHANNEL +/-  
10. CONTRAST +/-  
Press to adjust the contrast level.  
Press to select channels forward and  
backward under TV mode.  
Press to select stations forward and  
backward under AM/FM mode.  
11. VOL +/-  
Press to increase or decrease the  
speaker volume level.  
19. BRIGHT +/-  
Press to adjust brightness level.  
12. MUTE button  
Press to turn on/off the speaker output.  
The corresponding information will be  
displayed on the display panel.  
20. COLOR +/-  
Press to adjust color of the picture.  
 
- 11 -  
System Connections  
Do not connect the power cord until all other connections have been made.  
Each time you restart the unit, it remembers the last function used.  
Connecting To External AV Signal Source  
Connections should be made as follows:  
Connecting To TV Signal Input Source  
 
- 12 -  
System Connections  
Connecting To Antenna  
Connect the supplied AM/FM antennas to listen to the radio.  
In order to improve the signal, move AM loop antenna away from system and other  
equipment.  
Extend FM antenna fully.  
Keep the FM antenna as horizontal as possible after connection.  
When connecting the supplied AM loop antenna, connect two black cords to AM and  
ground jacks as shown below.  
If the FM reception is poor, please use a 75Ωcoaxial cable (not supplied) to connect  
system to an outdoor FM antenna as above.  
If you connect the system with outdoor FM antenna, you should earth the system in  
order to avoid lightning strike.  
Do not connect the earth wire to gas pipe to prevent gas explosion.  
 
- 13 -  
System Connections  
Connecting To the Power Adapter  
This unit is powered via the switching power adapter (supplied). See the below figure for  
details:  
1. Connect the AC adapter to jack marked with “DC 12V IN” on the rear panel of the unit.  
2. Plug the two-prong end of the power cord to the grounded electrical socket.  
3. When not using the unit, turn off the power of the unit first, and then unplug the power  
supply to prevent malfunctions.  
 
- 14 -  
Radio Function  
Radio Function Operation  
Press the AM or FM button on the remote control or front panel to enter AM or FM radio  
mode. Then press the SEEK+/- button for about 1.5 seconds on the remote control or  
front panel to start searching forward/backward from the current frequency. Press the  
SEEK+/- button again to stop searching. Radio frequency will be displayed on the  
display panel. The frequency range of FM is from 87.5MHz to 107.9MHz, frequency  
range of AM is from 520KHz to 1710KHz.  
Fine Tuning  
Press the SEEK+/- button on the remote control or front panel once to fine tune the  
frequency forward/backward under radio mode.  
Semi-memorizing radio stations  
If you like a radio station and want to store it for later listening, press the SET button to  
memorize it. “SAVE X X” will be displayed on the display panel; “X X” represents the  
default station number.  
There are two methods to organize the memorized stations:  
Use the ꢂꢃ buttons to adjust the channel number for your preference, and then  
press the SET button again, the station will be memorized with the coded station  
number.  
Press the SET button again, the station will be automatically memorized with the  
default station number in sequence.  
You can store radio stations from 0 to 19, total 20FM or 20AM radio stations. If no  
buttons are pressed within 3 seconds of pressing the SET button first time, the  
frequency will appear on the display panel again, and the station will not be stored.  
Accessing memorized radio stations  
Press the number buttons on the remote control to access a radio station by its  
memory location code.  
Press the CHANNEL+/- button on the remote control to select stations forward and  
backward.  
Press the ꢂꢃbuttons on the remote control or front panel to select the radio stations  
forward and backward.  
When selecting the stations, the “CH XX” will appear on the display panel, where the  
“XX” is the channel number of the stored radio station. After a few seconds, the “CH XX”  
disappears and the radio frequency will be displayed once again.  
 
- 15 -  
TV Function  
Basic Operation  
Connect the antenna to the antenna jack on the rear panel. After connecting the  
antenna, connect the power supply cord. If the player is in standby mode, press the  
POWER button on the front panel to turn on the power.  
Press the TV button on the remote control to shift to TV mode.  
Press the CHANNEL+/- buttons or ꢂꢃ buttons on the remote control, or use the  
number buttons directly, to select the desired channel.  
Some preferences can be preset:  
Picture Parameter Setup  
Press the MENU button once on the remote control to enter PICTURE setup menu, and  
screen display as shown:  
PICTURE  
Brightness  
Contrast  
Color  
11  
13  
14  
Language  
Reset  
English  
EXIT  
TV SETUP  
Use the , buttons to select the item you want to set (Brightness, Contrast, Color).  
Use the , buttons to adjust menu items between 0 and 20.  
Use the , buttons to select the Language, press the , buttons to select English,  
French or Spanish.  
To restore a setting to the original value, use the , buttons to select Reset, then  
press the OK button to confirm the change.  
Press the button on the remote control to exit from the setup menu.  
Press the button on the remote control to enter TV Setup menu.  
TV System Setup  
When the button is pressed, the TV system setup menu will appear:  
TV SETUP  
Signal  
CATV  
Channel  
Skip  
002  
ON  
Fine Tuning  
Auto Memory  
PICRURE ◄  
EXIT  
 
- 16 -  
TV Function  
Use the , buttons to select the item you want to set.  
Use the , buttons to enter the item and to select.  
Press the button on the remote control to exit from the setup menu.  
Press the button on the remote control to return to the picture setup menu.  
Signal  
Use the direction button to select CATV TV signal input mode.  
Use the direction button to select AIR TV signal input mode.  
Channel  
Use the , buttons to change the channel. In CATV input mode, you can select  
channels from 2 to 125; in AIR input mode, you can select channels from 2 to 69.  
Skip  
When the button is pressed to turn the function ON, it will skip the current channel  
when using CHANNEL +/-or , to select channels.  
When the button is used to turn the function OFF, it will play the channels in  
sequence when selecting under normal playback status.  
Fine Tuning  
Use the , buttons to select Fine Tuning, and then press the , buttons to tune  
forward or backward from the current channel  
Auto Memory  
Use the , buttons to select Auto Memory, press the OK button to enter auto  
memory mode:  
SEARCHING  
CH009  
EXIT◄  
--------------------------------------  
 
- 17 -  
TV Function  
The auto memory will take a few minutes. The unit will search channels from the lowest  
channel to the highest channel in the standard channel list. When tuning operations are  
complete the unit will exit and store the channels by sequence in the memory.  
During tuning, press the button to exit the auto memory.  
Use the CHANNEL +/- or , direction buttons to select the desired channel from  
those in memory.  
Timer Setup  
Press the SET button on the remote control to enter Timer setup menu, the screen will  
display as below:  
TIMER SET  
Timer  
OFF  
_ _: _ _ am  
_ _: _ _ am  
CATV  
Power on  
Power off  
Signal  
Channel  
002  
Exit : SET  
Use the , buttons to select the item you want to set.  
Use the , buttons to enter the item and to select.  
Press the SET button again on the remote control to exit from the setup menu.  
Timer  
Use the , direction buttons to select ON or OFF. This function allows you to set the  
start time and end time of the desired signal source. Whether the player is under TV,  
radio or standby mode, If set this function on, the player will automatically start the  
playback of the desired signal source.  
Select ON to activate the function; select OFF to disable the function.  
Power on  
To set the playback start time of the signal source. Use number buttons to input the  
desired start time in sequence of hour, minute. Press the , direction buttons to shift  
between am and pm.  
 
- 18 -  
TV Function  
Power off  
To set the playback end time of the signal source use number buttons to input the  
desired time in sequence of hour, minute. Press the , direction buttons to shift  
between am and pm. When the playback of the signal source is over, the player will  
enter standby mode.  
Signal  
Use the , direction buttons to select CATV, AIR, FM or AM.  
Channel  
Use number buttons to input the desired TV channels. In CATV signal input mode, there  
are 124 channels to choose from (2-125); in AIR signal input mode, there are 68  
channels to choose from (2-69).  
Press the CHANNEL+/- buttons or ꢂꢃ buttons on the remote control to select the  
desired channel, or use the number buttons to input and then press the OK button to  
confirm.  
Note:  
The function is active as long as the unit is continuously supplied with power. The unit  
will automatically play the selected input signal at the set start time and enter standby  
mode at the set end time each day.  
 
- 19 -  
AV Function  
AV Function  
The player has an additional AV input so it can function as a monitor for a DVD player,  
video cassette player, satellite receiver, video game, etc. When an AV source is  
connected, press the AV button on the remote control to enter external input AV mode.  
Picture Parameter Setup  
Press the MENU button once on remote control to enter PICTURE setup menu, and  
screen will display as shown:  
PICTURE  
Brightness  
Contrast  
Color  
11  
13  
14  
Language  
Reset  
English  
Exit  
Use the , buttons to select the item you want to set (Brightness, Contrast, Color).  
Use the , buttons to adjust menu items between 0 and 20.  
Use the , buttons to select the Language, press the , buttons to select English,  
French or Spanish.  
Select Reset to resume the original status.  
Press the button on the remote control to exit from the setup menu.  
Note:  
Under AV mode, if there is no signal, the LCD screen will be turned off automatically.  
When connected to an AV signal source, make sure the video type of the selected AV  
signal source is NTSC.  
 
- 20 -  
Installing the Unit in Kitchen  
Installing the unit under a cabinet  
The player unit may be installed in the kitchen with or without the spacers. The  
suggested mounting position of the unit is under a wall cabinet. See drawings below:  
NOTE: The dimensions of the player: 355mm X 75mm x285 mm (W/H/D)  
There should be at least 35mm distance between the unit and the wall.  
Installing steps  
1. Mark the position of the 4 holes by using the supplied template. Drill four 6.5 mm  
diameter holes. See below:  
 
- 21 -  
Installing the Unit in Kitchen  
2. If the cabinet door overhangs the shelf and obstructs the unit, adjust the unit or the  
shelf height for clearance.  
3. Install the unit with the supplied mounting screws.  
4. There should be at least 35mm distance between the unit and the wall.  
Quick hints  
Since the unit is rather heavy, be careful while doing the installation work.  
To reduce risk of fire, do not place any heating or cooking appliance beneath the  
unit, especially while the LCD screen is open for viewing.  
Mount the unit so that its AC power cord can be plugged directly to a wall outlet.  
Do not use a converter or extension cord.  
Be sure that the AC power cord has no slack when the player is working, because  
the cord acts as an FM wire antenna. If the AC power cord has some slack, wind it  
up to the cord hook until the cord has no slack.  
The unit has a built-in ferrite bar antenna for AM radio reception. Check the  
condition of AM reception before fixing in position.  
Install the unit as far as possible from a source of noise, for example, refrigerator,  
microwave oven, fluorescent lamp, etc.  
 
- 22 -  
Troubleshooting  
SYMPTOM  
CHECK ITEM  
Make sure system connection is correct.  
Make sure the player is not under muting mode.  
Press the MUTE button to turn on the speaker.  
Make sure the volume is adjusted to the lowest.  
Adjust the volume upward.  
There is no sound.  
There is no picture  
or the position of  
the picture is  
Make sure the video type of the AV signal source TV is  
NTSC.  
Make sure system connection is correct.  
incorrect.  
Make sure there are no obstructions between the remote  
control and the player.  
Make sure the remote control is pointing at the player.  
Make sure batteries are inserted correctly (check polarity).  
Replace weak batteries.  
The remote control  
does not work.  
Other Notes:  
Static or other external interfere may cause the player to behave abnormally. If this  
occurs, unplug the power-supply cord from the outlet and plug it in again to reset the  
player. If the problems persist, then please disconnect the power and consult a qualified  
technician.  
 
- 23 -  
Specifications  
LCD screen size  
System  
7 inches  
PLL  
AM  
FM  
520~1710kHz  
Radio  
Frequency  
Range  
87.5~107.9MHz  
Power  
AC100V~ 240V, 50/60Hz  
<16W  
Power Consumption  
Dimension  
Weight  
355mm X 75mm x285 mm (W/H/D)  
About 3.4kgs  
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE  
For service, support and warranty information, visit www.polaroidelectronics.com or in  
the US call 1-866-289-5168, in Canada call 1-866-301-7922 and in Mexico call 01-800-  
400-2443.  
“Polaroid” is a registered trademark of Polaroid Corporation of Waltham, MA USA and  
licensed for use on the FCM-0700A to Petters Consumer Brands, LLC.  
 
- 24 -  

Peerless Industries Projector Accessories PRS KIT0811 User Manual
Philips Bottle Warmer SCF643 07 User Manual
Philips Work Light P 5561 D User Manual
Planet Technology Digital Camera ICA 120 User Manual
Plantronics Headphones W440 M User Manual
Polycom Network Card KIRK ISDN User Manual
Porter Cable Automobile Parts N030679 User Manual
Poulan Pole Saw 545117550 User Manual
Poulan Snow Blower PR1030ES User Manual
Poulan Tiller 417134 User Manual