Register your product and get support at
SE 7450
EN Telephone Answering Machine
Warning
Use only rechargeable batteries.
Charge the handset for 24 hours before use.
Table of contents
1
Safety information
3
4
Your phone
11
11
12
1.1
Equipment Approval
Information
4.1
4.2
What’s in the box
Overview of your phone
3
4
1.2
1.3
Interference Information
5
Getting started
15
Hearing Aid Compatibility
(HAC)
5
5
5.1
Install your phone
15
1.4
FCC RF Radiation Exposure
Statement
6
Use more of your phone 16
2
Important
6
6
7
6.1
Using the Intercom
16
2.1
2.2
2.3
Power requirements
Conformity
7
Personal settings
Handset Tones
18
18
19
19
19
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
Electric, Magnetic and
Electromagnetic Fields ("EMF") 7
Set Wallpaper
Set Contrast Level
Change the Handset Name
2.4
2.5
Recycle your batteries
Service Centers
8
8
Change the Display Language 19
3
Configure your SE7450
Install battery
9
9
9
9
Babysit mode
20
20
20
3.1
3.2
3.3
Set Backlight time
Set Theme Colour
Change the Display Language
Registration
Table of contents
1
8
Advanced settings
Registration
21
21
21
8.1
8.2
Unregister a handset
9
Games
22
22
22
9.1
9.2
Play Snake game
Play Tetris game
10
11
Technical data
23
Frequently asked
questions
24
27
12
Index
2
Table of contents
requirements adopted by the ACTA. A
compliant telephone cord and modular
plug is provided with this product. It is
designed to be connected to a compatible
modular jack that is also compliant. See
installation instructions for details.
1
Safety information
1.1
Equipment Approval
Information
Notes
Your telephone equipment is approved
for connection to the Public Switched
Telephone Network and is in compliance
with parts 15 and 68, FCC Rules and
Regulations and the Technical
•
This equipment may not be used on
coin service provided by the telephone
company.
•
Party lines are subject to state tariffs,
and therefore, you may not be able to
use your own telephone equipment if
you are on a party line. Check with
your local telephone company.
Notice must be given to the telephone
company upon permanent
disconnection of your telephone from
your line.
If your home has specially wired alarm
equipment connected to the
Requirements for Telephone Terminal
Equipment published by ACTA.
•
•
1.1.1 Notification to the Local
Telephone Company
On the bottom of this equipment is a
label indicating, among other information,
the US number and Ringer Equivalence
Number (REN) for the equipment. You
must, upon request, provide this
information to your telephone company.
The REN is useful in determining the
number of devices you may connect to
your telephone line and still have all of
these devices ring when your telephone
number is called. In most (but not all)
areas, the sum of the RENs of all devices
connected to one line should not exceed
5. To be certain of the number of devices
you may connect to your line as
telephone line, ensure the installation
of this product does not disable your
alarm equipment. If you have questions
about what will disable alarm
equipment, consult your telephone
company or a qualified installer.
US Number is located on the cabinet
bottom.
REN Number is located on the cabinet
bottom.
determined by the REN, you should
contact your local telephone company.
A plug and jack used to connect this
equipment to the premises wiring and
telephone network must comply with the
applicable FCC Part 68 rules and
1.1.2 Rights of the Telephone
Company
Should your equipment cause trouble on
your line which may harm the telephone
network, the telephone company shall,
Safety information
3
where practicable, notify you that
temporary discontinuance of service may
be required. Where prior notice is not
practicable and the circumstances
warrant such action, the telephone
company may temporarily discontinue
service immediately. In case of such
temporary discontinuance, the telephone
company must: (1) promptly notify you of
such temporarydiscontinuance; (2) afford
you the opportunity to correct the
situation; and (3) inform you of your right
to bring a complaint to the Commission
pursuant to procedures set forth in
Subpart E of Part 68, FCC Rules and
Regulations.
The telephone company may make
changes in its communications facilities,
equipment, operations or procedures
where such action is required in the
operation of its business and not
inconsistent with FCC Rules and
Regulations. If these changes are
expected to affect the use or
ensured, although there is no guarantee
this will not occur in a given installation. If
interference is suspected and verified by
switching this equipment on and off, the
user is encouraged to try to correct the
interference by one or more of the
following measures: Reorient the radio/
television receiver’s antenna, relocate
the equipment with respect to the
receiver, plug the equipment and receiver
into separate circuit outlets. The user
may also wish to consult a qualified radio/
television technician for additional
suggestions. This equipment has been
fully tested and complies with all limits for
Class B computing devices pursuant to
part 15 FCC Rules and Regulations. This
device complies with RSS-210 of Industry
Canada. Operation is subject to the
following two conditions: (1) This device
may not cause interference, and (2) This
device must accept any interference,
including interference that may cause
undesired operation of the device.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
performance of your telephone
equipment, the telephone company must
give you adequate notice, in writing, to
allow you to maintain uninterrupted
service.
(1) This device may not cause harmful
interference; and (2) This device must
accept any interference received,
including interference that may cause
undesired operation.
1.2
Interference Information
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are
designed to provide reasonable
This equipment generates and uses radio
frequency energy which may interfere
with residential radio and television
reception if not properly installed and
used in accordance with instructions
contained in this manual. Reasonable
protection against such interference is
protection against harmful interference in
a residential installation.
4
Safety information
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
004-000-00345-4 when ordering copies.
Notice: The changes or modifications not
expressly approved by the party
responsible for compliance could void the
user's authority to operate the
equipment.
Privacy of Communications may not be
ensured when using this product.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment offand on, theuser isencouraged
to try to correct the interference by one or
more of the following measures:
1.3
Hearing Aid Compatibility
(HAC)
This telephone system meets FCC/
Industry Canada standards for Hearing
Aid Compatibility.
1.4
FCC RF Radiation Exposure
Statement
•
•
•
Reorient or relocate the receiving
antenna (that is, the antenna for radio
or television that is “receiving” the
interference).
Reorient or relocate and increase the
separation between the
telecommunications equipment and
receiving antenna.
Connect the telecommunications
equipment into an outlet on a circuit
different from that to which the
receiving antenna is connected.
This equipment complies with FCC RF
radiation exposure limits set forth for an
uncontrolled environment. This
equipment should be installed and
operated with a minimum distance of 20
centimeters between the radiator and
your body. This transmitter must not be
co-located or operated in conjunction
with any other antenna or transmitter.
For body worn operation, this phone has
been tested and meets the FCC RF
exposure guidelines when used with the
belt clip supplied with this product. Use of
other accessories may not ensure
compliance with FCC RF exposure
guidelines.
If these measures do not eliminate the
interference, please consult your dealer
or an experienced radio/television
technician for additional suggestions.
Also, the Federal Communications
Commission has prepared a helpful
booklet, “How To Identify and Resolve
Radio/TV Interference Problems.” This
booklet is available from the U.S.
GovernmentPrinting Office, Washington,
D.C. 20402. Please specify stock number
Safety information
5
NOTES: This equipment may not be used
on coin service provided by the
telephone company.
2
Important
Take time to read this user manual before
you use your phone. It contains important
information and notes regarding your
phone.
2.1
Power requirements
•
This product requires an electrical
supply of 220-240 volts AC. In case of
power failure, the communication can
be lost.
NOTICE: This product meets the
applicable Industry Canada technical
specifications.
The equipment must be installed using an
acceptable method of connection. The
customer should be aware that
compliance with the above conditions
may not prevent degradation of service in
some situations.
•
The Electrical network is classified as
hazardous. The only way to power
down the charger is to unplug the
power supply from the electrical
outlet. Ensure that the electrical outlet
is always easily accessible.
•
The voltage on the network is
classified as TNV-3
Repairs to certified equipment should be
made by an authorized Canadian
maintenance facility designated by the
supplier. Any repairs or alterations made
by the user to this equipment, or
equipment malfunctions, may give the
telecommunications company cause to
request the user to disconnect the
equipment.
Users should ensure for their own
protection that the electrical ground
connections of the power utility,
telephone lines and internal metallic
water pipe systems, if present, are
connected together. This precaution may
be particularly important in rural areas.
CAUTION: Users should not attempt to
make such connections themselves, but
should contact the appropriate electric
inspection authority, or electrician, as
appropriate.
(Telecommunication Network
Voltages), as defined in the standard
UL 60950.
Warning
To avoid damage or malfunction:
•
Do not allow the charging contacts or
the battery to come into contact with
metal objects.
Do not open it as you could be
exposed to high voltages.
Do not allow the charger to come into
contact with liquids.
Never use any other battery than the
one delivered with the product or
recommended by Philips: risk of
explosion.
Always use the cables provided with
the product.
Handsfree activation could suddenly
increase the volume in the earpiece to
a very high level: make sure the
handset is not too close to your ear.
•
•
•
•
•
6
Important
•
•
This equipment is not designed to
make emergency calls when the power
fails. An alternative has to be made
available to allow emergency calls.
Do not expose the phone to excessive
heat caused by heating equipment or
direct sunlight.
Do not drop your phone or allow
objects to fall on your phone.
Do not use any cleaning agents
containing alcohol, ammonia, benzene,
or abrasives as these may harm the
set.
Do not use the product in places
where there are explosive hazards.
Do not let small metal objects come
into contact with the product. This can
deteriorate audio quality and damage
the product.
networks of the countries mentioned on
the packaging.
You can find the Declaration of
2.3
Electric, Magnetic and
Electromagnetic Fields
("EMF")
•
•
1. Philips Royal Electronics manufactures
and sells many consumer oriented
products which usually, as with any
electronic apparatus, have the ability
to emit and receive electro magnetic
signals.
•
•
2. One of Philips' leading Business
Principles is to take all necessary
health and safety precautions for our
products, to comply with all applicable
legal requirements and to stay well
within the EMF standards applicable at
the time of producing the products.
3. Philips is committed to develop,
produce and market products that
cause no adverse health effects.
4. Philips confirms that if its products are
handled properly for their intended
use, they are safe to use according to
scientific evidence available today.
5. Philips plays an active role in the
development of international EMF and
safety standards, enabling Philips to
anticipate further developments in
standardisation for early integration in
its products.
•
Active mobile phones in the vicinity
may cause interference.
About operating and storage
temperatures:
•
•
•
Operate in a place where temperature
is always between 0 and 35º C (32 to
95º F).
Store in a place where temperature is
always between -20 and 45º C (-4 to
113º F).
Battery life may be shortened in low
temperature conditions.
2.2
Conformity
We, Philips declare that the product is in
compliancewiththeessentialrequirements
and other relevant provisions of Directive
1999/5/EC. This product can only be
connected to the analogue telephone
Important
7
2.4
Recycle your batteries
2.5
Service Centers
Do not dispose your rechargeable
batteries. Call the toll fee number 1-800-
822-8837 to get instructions on how to
recycle your batteries.
Call Center (USA and Canada):
800-233-8413
E-mail support:
®
The RBRC Seal on
the nickel metal
hydride battery
indicates that Philips
Royal Electronics is
voluntarily
participating in an industry program to
collect and recycle these batteries at the
end of their useful lives, when taken out
of service within the United States and
Canada.
®
The RBRC program provides a
convenient alternative to placing used
nickel metal hydride batteries into the
trash or municipal waste, which may be
illegal in your area.
®
Philips’s participation in RBRC makes it
easy for you to drop off the spent battery
at local retailers participating in the
®
RBRC program or at authorized Philips
product service centers.
Please call 1-800-8-BATTERY for
information on Ni-MH battery recycling
and disposal bans/restrictions in your
area. Philips’s involvement in this program
is part of its commitment to protecting
our environment and conserving natural
resources.
®
RBRC is a registered trademark of
Rechargeable Battery Recycling
Corporation.
8
Important
Scroll : to your desired language
2
and press mSELECT to confirm.
3
Configure your
SE7450
•
A validation tone is emitted and the
screen returns to previous menu.
Tip
Once the display language is set, the
option menus on the handset will switch
to display in the selected language
3.1
Install battery
Warning
immediately. However, it will not change
the language of the predefined outgoing
message of your answering machine.
Always use AAA rechargeable batteries
supplied with your unit. There could be
risk of battery leakage if you use alkaline
batteries or other battery types.
Slide out the battery cover.
1
3.3
Registration
The procedures described below are the
procedures that you will find in your
handset. The procedures may vary
according to the handset you want to
register. In this case, please refer to the
manufacturer of the additional handset.
Additional handsets must be registered to
the base unit before you can use them. Up
to 6 handsets can be registered to one
base station.
Place the batteries in the correct
polarity as indicated and replace the
cover.
2
The Master PIN is required before you
can register or unregister handsets.
Note
By default, the Master PIN is 0000.
3.3.1 Register your SE7450
After charging it for a few minutes, the
word WELCOME appears on a blue
screen. Next, the idle screen appears.
Follow these steps to register your
handset:
3.2
Change the Display Language
Your handset can support different display
languages, depending on your country
selection during the WELCOME mode.
Press mMENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to
1
In idle mode, the message “Press
1
Base page key for 3 secs. Press and
Language and press mSELECT
.
Configure your SE7450
9
hold
m
”
will be prompted on the
screen. Follow the screen
instructions to start registration.
Enter PIN will be displayed on your
screen. Enter the default Master PIN
number - 0000.
2
3
Press mOK to confirm your
registration.
Note
All the handset keys (except the m
key) are deactivated until the above
registration process is completed.
10
Configure your SE7450
Note
If you have not subscribed to Caller Line
Identification service, there will not be
any alerts for new events except for new
messages recorded on the answering
machine. Hence, the event LED will not
blink when there is a new call, or
voicemail.
4.2
Overview of your phone
C
D
Display
Left Softkey
m
In idle mode: Go to the main menu.
In other modes: Select the function
displayed on the handset screen directly
above it.
During a call: Mute/unmute the handset
microphone.
Switch on the backlight.
E
Right Softkey
>
In idle mode: Access the Redial list.
In other modes: Select the function
displayed on the handset screen directly
above it.
During a call: Initiate a second call, consult
phonebook, transfer a call or activate/
deactivate XHD Sound mode.
Switch on the backlight.
F
Navigation keys
:
In idle mode: Scroll up to access the Call
log and scroll down to access the
Phonebook.
During a call: Scroll up/down to increase
or decrease earpiece and speaker
volume.
In editing mode: Scroll up/down to go to
the previous character or next character.
In other modes: Scroll up/down a menu
list or go to the previous or next record
in the Phonebook, Redial list or Call log.
A
B
Earpiece
Event LED
Blinks when there is a new missed call or
Voicemail or answering machine message.
Turns off when there are no new events
or when all new events have been read.
12
Your phone
r
G
Talk key
In idle mode: Answer an incoming
external or internal call.
During a call: Activate the recall function.
In other modes: Dial the selected number
in the Phonebook, Redial list or Call log.
H
Hang-up key
e
In idle mode: Long press to switch off the
handset, Short press to switch on the
handset.
During a call: Hang up a call.
In other modes: Return to idle mode.
I
Keypad lock/Format key
*
In idle mode: Insert *. Long press to lock/
unlock the keypad.
During a call: Insert *.
In call log reviewing mode: Press
repeatedly
to view the alternate dialing sequences.
J
Ringer on/off key & Pause key
#
In idle mode: Insert #. Long press to turn
the ringer on/off.
During a call: Insert #.
When predialling: Long press to insert a
pause marked “P”.
In editing mode: Long press to switch
between upper and lower case.
K
Loudspeaker key
v
In idle mode: Turn on the loudspeaker
and dial the number. Answer an incoming
call using handsfree mode.
During a call: Toggle the loudspeaker on/
off.
L
Call transfer key & Intercom
key
ic
In idle mode: Initiate an internal call.
During a call: Hold the line and page
another handset.
M
Microphone
Your phone
13
5
Getting started
5.1
Install your phone
Before using the handset, the batteries
have to be installed and fully charged.
5.1.1 Install battery
See page 9.
5.1.2 Charge battery
Warning
The handset must be charged for at least
24 hours before using it for the first time.
When the battery level becomes low, an
empty battery icon is displayed on the
screen.
If the battery level becomes exceedingly
low, the phone automatically switches off
and any function in progress will not be
saved.
Placethehandsetonthechargingcradle
of the base station. A melody is emitted
if the handset is placed correctly.
1
The battery icon
blinks during charge.
The battery icon
steady when the handset is fully
charged.
on the display
2
3
becomes
Note
Optimal battery life is reached after 3
cycles of complete charging (over 15
hours) and discharging, allowing
approximately 12 hours of talk-time and
150 hours of stand-by time.
Getting started
15
6.1.2 Transfer an external call to
another handset
6
Use more of your
phone
During the call, press and hold
ckey to put the external call on
hold (the caller can no longer hear
you).
1
6.1
Using the Intercom
Warning
•
Intercom is established immediately
if there are only 2 registered
handsets.
Intercom and call transfer is only possible
with handsets registered to the same base
station.
If there are more than 2 registered
handsets, the handset numbers
which are available for intercom will
be displayed. Scroll : to All
2
This feature is only available when there
are at least 2 registered handsets. It
allows you to make free internal calls,
transfer external calls from one handset
to another and use the conference
option.
Handsets and press mSELECT to
call all the handsets or scroll : to
the specific handset you want to call
and press mSELECT
.
•
The called handset rings.
Press rkey on the called handset
to answer the internal call, where
both internal callers can talk.
3
4
6.1.1 Intercom another handset
Note
If the handset does not belong to SE740/
745 range, this function may not be
available.
•
Intercom is established.
Press e key on the first handset
to transfer the external call to the
called handset.
Press c key in idle mode.
1
•
Intercom is established immediately
if there are only 2 registered
handsets.
•
The external call is transferred.
Note
If there is no answer from the called
handset, press c key to resume the
external call.
If there are more than 2 registered
handsets, the handset numbers
2
which are available for intercom will
be displayed. Scroll : to All
Handsets and press mSELECT to
call all the handsets or scroll : to
the specific handset you want to call
6.1.3 Answer an external call
during intercom
When there is an incoming external
call during an intercom, a new call
tone is emitted.
1
and press mSELECT
.
16
Use more of your phone
To answer the external call and end
Press rkey on the called handset
to answer the internal call, where
both internal callers can talk.
2
3
4
the intercom, press r.
•
Connection with the external call is
established.
•
Intercom is established.
Press and hold c key for 2
seconds on the first handset to start
the three-party conference.
Tip
To put the internal call on hold and
answer the incoming external call, press
ckey.
•
CONFERENCE will be displayed on
the screen once the conference call
is established.
Tip
6.1.4 Switch between an internal
and external call
To switch between an internal or
external call, press c key.
If CONFERENCE mode is activated, a
three-party conference call is
automatically established if the second
handset takes the line when there is
already an external call in progress.
6.1.5 Establish a three-party
conference call
The conference call feature allows one
external call to be shared with two
handsets (in intercom). The three parties
can share the conversation and no
network subscription is required.
During the call, long press ckey
to put the external call on hold (the
caller can no longer hear you).
1
•
Intercom is established immediately
if there are only 2 registered
handsets.
If there are more than 2 registered
handsets, the handset numbers
2
which are available for intercom will
be displayed. Scroll : to All
Handsets and press mSELECT to
call all the handsets or scroll : to
the specific handset you want to call
and press mSELECT
.
•
The called handset rings.
Use more of your phone
17
7.1.2 Set the Ring Melody
There are 10 polyphonic ring melodies
available on your handset.
7
Personal settings
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, press mSELECT to
enter Handset Tones, scroll : to
Ring Melody and press mSELECT
1
7.1
Handset Tones
7.1.1 Set the Ring Volume
.
Danger
Scroll :to your desired melody to
play the melody.
2
3
When setting the ring volume of your
phone or when the handset rings during
an incoming call, please do not hold the
handset too close to your ear as the
volume of the ringing tone may damage
your hearing.
Press mSELECT to set the ring
melody.
•
A validation tone is emitted and the
screen returns to previous menu.
There are 6 ringer volume options
(
Silence
,
Low, Medium, High, Boost and
7.1.3 Set the Group Melody
To benefit from this feature, you must
subscribe to the Caller Line ldentification
service.
Progressive). The default level is Medium
1
.
Press m MENU in idle mode,
scroll : to Personal Set and press
m
SELECT press mSELECT to
This feature enables you to select and set
the melodies to be played when there is an
external incoming call from a contact
whose name is stored in your phonebook
and belongs to a phonebook group. You
can associate 1 ring melody to each group.
There are three phonebook groups
(Group A, B and C) available for you to
organise your contacts. Each group can
be assigned a unique melody.
enter Handset Tones and press
mSELECT again to enter Ring
Volume
.
Scroll : to your desired volume
level and press mSELECT to
confirm.
2
•
A validation tone is emitted and the
screen returns to previous menu.
Note
Press m MENU in idle mode,
1
When Silence is activated, the icon
be displayed on the screen.
will
scroll : to Personal Set and press
m
SELECT, press m SELECT
to enter Handset Tones, scroll :
to Group Melody and press m
SELECT
.
18
Personal settings
Scroll : to the group for which
2
you wish to set melody and press
7.3
There are 3 contrast level options (Level
Level 2 or Level 3). The default contrast
level is Level 2
Set Contrast Level
m
SELECT.
Scroll : to the desired melody to
play the melody.
3
4
1,
.
Press mSELECT to set the group
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to Contrast
1
melody.
•
A validation tone is emitted and the
screen returns to previous menu.
and press mSELECT
.
Scroll : to your desired contrast
2
level (Level 1 Level 2 or Level 3) and
,
7.1.4 Activate/Deactivate Key Beep
A single beep is emitted when a key is
pressed. You can enable or disable the
press mSELECT to confirm.
•
A validation tone is emitted and the
screen returns to previous menu.
key beep. By default, the key beep is On
.
Press m MENU in idle mode,
1
scroll : to Personal Set and press
7.4
Change the Handset Name
m
SELECT, press m SELECT
You can name the handset and display the
handset name in idle mode. The default
to enter Handset Tones, scroll :
to Key Beep and press mSELECT
Scroll : to On or Off and press
mSELECT to confirm.
.
handset name of your handset is PHILIPS
.
2
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to Handset
1
•
A validation tone is emitted and the
screen returns to previous menu.
Name and press mSELECT
.
Edit the handset name (maximum 14
characters) and press mOK to
confirm.
2
7.2
Set Wallpaper
This feature allows you to select the
wallpaper to be displayed in idle mode.
There are 5 wallpapers pre-installed on
•
A validation tone is emitted and the
screen returns to previous menu.
your handset. The 5th wallpaper is a blank
wallpaper.
7.5
See page 9.
Change the Display Language
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to
1
Wallpaper and press mSELECT
.
Scroll :to your desired wallpaper
2
and press mSELECT to confirm.
•
A validation tone is emitted and the
screen returns to previous menu.
Personal settings
19
7.6
Babysit mode
7.6.2 Deactivate Babysit Mode
You must have at least 2 handsets
registered to your base station to be able
to use this feature (see page 9
Press m MENU in idle mode,
1
select Off and press mSELECT
.
"Registration"). This feature allows you to
monitor, e.g. the baby’s room.
7.7
Set Backlight time
To use the Babysit feature you need to
activate it (e.g. on handset 1) and enter the
number of the handset to be called (e.g.
handset 2) in the event that there are
noises in the monitored room. Place the
handset which is in Babysit mode (e.g.
handset 1) in the room to be monitored. If
this handset detects a sound level greater
than a certain threshold, it will
Press m MENU in idle mode,
1
scroll : to Personal Set and press
mSELECT, scroll :to Backlight
Time and press mSELECT
.
Scroll : to 20s
press mSELECT to confirm.
A validation tone is emitted.
Note
,
40s or 60s and
2
•
By default, the backlight remains on for 20
seconds after each activation such as an
incoming call, key presses, lifting the
handset off the base station, etc.
automatically initiate an internal call to the
selected handset (e.g. handset 2).
7.6.1 Activate Babysit Mode
Note
7.8
Set Theme Colour
In Babysit mode, all keys are deactivated
except for mMENU key. The handset
cannot perform any normal operation
(making an outgoing call, receiving an
incoming call, intercom another handset,
paging, etc.) once this function is
activated.
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to Theme
1
Colour and press mSELECT
.
Scroll : to Theme Colour 1
,
2
Theme Colour 2 or Theme Colour 3
and press mSELECT to confirm.
•
A validation tone is emitted.
Press m MENU in idle mode,
scroll : to Personal Set and press
mSELECT, scroll : to Babysit
1
mode and press mSELECT
.
•
Babysit mode is displayed on the
screen.
Scroll : through the list of
handsets available and press
mSELECT to select the handset
to be called.
2
20
Personal settings
8
Advanced settings
8.1
Registration
See page 9.
8.2
Unregister a handset
Press mMENU in idle mode,
scroll :to Advanced Set and press
mSELECT, scroll : to
Unregistration and press
1
mSELECT
.
Enter the Master PIN when
prompted and press mOK to
confirm.
2
Note
By default, the Master PIN is 0000.
Scroll : to select the handset
3
number to unregister and press
mSELECT
.
•
A validation tone is emitted to
indicate successful unregistration
and the screen shows
UNREGISTERED
.
Note
If no action is taken on the handset within
15 seconds, the unregistration procedure
will be aborted and the handset returns
to idle mode.
To unregister a handset that does not
belong to the SE740/745 range, you can
only use the SE740/745 handset to
unregister it.
Advanced settings
21
Note
Press 2 / 4 / 6 / 8 keys to
rotate / move left / move right / move
down respectively.
9
Games
To start the game, press
2
9.1
Play Snake game
mSELECT
.
The objective of this game is to move the
snake and eat as many "food blocks” as
possible. When the food is eaten, the
snake grows in length and the score
increases. Once you hit the body of the
snake itself, the game is over. .
To exit from the game, press >.
3
PressmMENU in idle mode, scroll
1
: to Games and press
mSELECT, scroll : to Snake
and press mSELECT
.
•
An instruction screen is displayed.
Note
Press 2 / 4 / 6 / 8 keys to
move up / move left / move right / move
down respectively.
Press 5 to pause/continue with the
game. Press : to select the difficulty
level.
To start the game, press
2
mSELECT or 5 key.
To exit from the game, press >.
3
9.2
Play Tetris game
You can rotate each shaped block as they
fall such that they fit neatly into horizontal
blocks. The more blocks you can gather
within the same level, the more you will
score.
PressmMENU in idle mode, scroll
1
: to Games and press
mSELECT, scroll : to Tetris
and press mSELECT
.
•
An instruction screen is displayed.
22
Games
10 Technical data
Display
•
Progressive LCD backlight
General telephone features
•
•
Dual mode caller name & number
identification
10 polyphonic ringer melodies
Battery
•
2 x HR AAA NiMh 600 mAh batteries
Power Consumption
•
Power consumption at idle mode:
around 800mW
Temperature range
•
Operation: Between 0 and 35º C (32
to 95º F).
•
Storage: Between -20 and 45º C (-4 to
113º F).
Relative humidity
•
Operation: Up to 95% at 40°C
•
Storage: Up to 95% at 40°C
Technical data
23
11 Frequently asked
questions
In this chapter, you will find the most
frequently asked questions and answers
about your phone.
Warning batt. is displayed on
handset!
Connection
•
Use only AAA rechargeable batteries
supplied with your unit. There could
be risk of battery leakage if you use
alkaline batteries or other battery
types.
The handset does not switch on!
•
Charge the batteries: Put the handset on
the base station to charge. After a few
moments, the phone will switch on.
The handset does not charge!
•
Check charger connections.
Set-up
icon is not blinking during
charge!
•
•
•
•
Battery is full: There is no need to
charge the battery.
Bad battery contact: Adjust the
handset slightly.
Dirty contact: Clean the batteries
contact with a dry cloth.
Wrong batteries installed: Use only
AAA rechargeable batteries supplied
with your unit There could be risk of
battery leakage if you use alkaline
batteries or other battery types.
Communication is lost during a call!
•
Charge the battery
Silence, and make sure
icon is not
•
Move closer to the base station.
displayed on the screen (see “Set the Ring
Volume” on page 18).
The phone is "Out of range"!
•
Move closer to the base station.
24
Frequently asked questions
Caller cannot hear me at all!
Microphone may be muted: During a call,
handset, unregister an existing
handset.
press mUNMUTE
.
•
•
Remove and replace the handset
batteries.
Try again by disconnecting and
connecting the base station power
supply and follow the procedure to
register a handset.
There’s no dialling tone!
•
•
No power: Check the connections.
Batteries are empty: Charge the
batteries.
•
•
Move closer to the base station.
Wrong line cable used: Use the line
cable provided.
•
Make sure that you have entered the
correct PIN code. If you have not
changed it, by default it is 0000.
•
Line adaptor is required: Connect the
line adaptor to the line cord.
Caller’s number is not displayed!
•
Service is not activated: Check your
subscription with your network
operator.
Caller cannot hear me clearly!
•
•
Move closer to the base station.
Move the base station at least one
metre away from any electronic
appliances.
Poor audio quality and the antenna
icon is blinking!
•
The indoor and outdoor range of the
phone is up to 50 metres and 300
metres respectively. When the
Frequent noise interference on my
radio or television!
handset moves beyond the operation
•
Move the base station as far away as
range, the antenna icon
will blink.
possible from the electrical appliances.
My handset keeps going into idle
mode!
Product behaviour
•
If there are no key presses for 30
seconds, the handset will automatically
return to idle mode. It will also return
to idle mode automatically when you
place the handset back on the base
station.
Keypad does not work!
•
Unlock your keypad: Long press *
in idle mode.
The handset warms up when
making a long call!
Phonebook entry cannot be stored
and MEMORY FULL is displayed!
•
This is a normal behavior. The handset
consumes energy while calling.
•
Delete an entry to free memory
before saving your contact again.
The handset cannot be registered to
the base station!
•
Maximum number of handsets has
been reached. To register a new
Frequently asked questions
25
The copy from my mobile phone
SIM card to SE7450 is not complete!
•
Only phonebook entries from your
mobile phone SIM card will be
transferred. If you have phonebook
entries on your mobile phone
memory, transfer them to your mobile
phone SIM card before transferring to
your SE7450.
The Master PIN code is wrong!
•
•
The default master PIN is 0000.
If it has been changed before, and you
cannot remember the new one, reset
the handset to revert to the default
master PIN code.
26
Frequently asked questions
12 Index
S
A
Switch handset on/off 16
Accessories 11
Answer an external call 16
U
B
Unregister 21
Backlight time 20
C
Charge battery 15
Conference call 17
Connect base station 15
D
Display icons 14
H
Handset Name 19
Handset Tones 18
I
Install battery 9
Install phone 15
Intercom 16
K
Key Tone 19
L
Language 9
O
Overview of your phone 12
R
Recycle your batteries 8
Registration 9
Ring Melody 18
Ring Volume 18
Index
27
Copyright © 2007 Koninklijke Philips Electronics N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
Specifications are subject to change without notice.
Document order number: 3111 285 37421 (EN/ES/FR)
Printed in China.
|