Philips DVD VCR Combo DVD757VR User Manual
DVD757VR  
Digital Video Disc Player &  
Video Cassette Recorder  
R
 
General Information  
Introduction  
The region code for this set is 2.  
Thank you for purchasing this Philips DVD/VCR.This  
wner’s Manual explains the basic operation of this DVD/VCR.  
Since it is usual for DVD movies to be released  
at different times in different regions of the  
world, all players have region codes and discs can  
have an optional region code. If you load a disc  
of a different region code to your player, you will  
see the region code notice on the screen.The  
disc will not playback, and should be unloaded.  
Environmental Information  
All unnecessary packaging has been omitted.  
Packaging has been made easy to separate into three materials:  
cardboard (box), polystyrene foam (buffer) and polyethylene  
(bags, protective foam sheet).  
2
Your DVD/VCR consists of materials which can be recycled  
and reused if disassembled by a specialised company. Please  
observe the local regulations regarding the disposal of packag-  
ing materials, exhausted batteries and old equipment.  
Manufactured under license from Dolby Laboratories.“Dolby”  
and the double-D symbol are trademarks of Dolby  
Laboratories.  
This product incorporates copyright protectiontechnology that  
is protected by method claims of certain U.S. patents and other  
intellectual property rights owned by Macrovision Corporation  
and other rights owners. Use of this copyright protection tech-  
nology must be authorised by Macrovision Corporation, and is  
intended for home and other limited viewing uses only unless  
otherwise authorised by Macrovision Corporation. Reverse  
engineering or disassembly is prohibited.  
Supplied Accessories  
• Remote control  
•
Batteries (two AA size) for remote control  
• SCART cable (not available for all versions) • Audio Cable  
• RF Coaxial cable • Owner’s Manual  
Safety Information  
•To reduce the risk of fire or electric shock, do not expose  
this device to rain or moisture.  
The DVD/VCR is in conformity with the  
EMC directive and low-voltage  
directive.  
• Before operating the DVD/VCR, check that the operating  
voltage indicated on the typeplate (or the voltage indication  
beside the voltage selector) is identical with the voltage of  
your local power supply. If not, please consult your dealer.  
• Place the DVD/VCR on a flat, hard and stable surface.  
• There must be sufficient room in front of the player for the  
disc tray to be opened.  
• In cabinet, allow about 2.5cm (1 inch) of free space all around  
the player for adequate ventilation.  
• Do not expose your player to extreme of temperature or  
humidity.  
• If the DVD/VCR is brought directly from a cold to a warm  
location, or is placed in a very damp room, moisture may  
condense on the lens of the disc unit inside the DVD/VCR  
player. Should this occur, the DVD/VCR would not operate  
normally. Leave the player on for about one hour with no disc  
in the DVD/VCR until normal playback is possible.  
•The mechanical parts of the set contain self-lubricating bear-  
ings and must not be oiled or lubricated.  
For Customer Use:  
Read carefully the information located at the bottom of  
your DVD/VCR and enter below the Serial No.Retain this  
information for future reference.  
Model No. DVD/VCR  
Serial No. ________________________________________  
Laser safety  
This unit employs a laser. Due to possible eye injury, only a  
qualified service person should remove the cover or attempt  
to service this device.  
USE OF CONTROLS OR  
ADJUSTMENTS OR PERFORMANCE OF PROCE-  
DURES OTHERTHANTHOSE SPECIFIED HEREIN  
MAY RESULT IN HAZARDOUS RADIATION EXPO-  
SURE.  
• Never spill liquid of any kind on this unit. If liquid is spilled  
into the unit, consult qualified service engineer.  
• When the DVD/VCR is switched to Standby mode, it  
is still consuming some power. To disconnect the sys-  
tem from the power supply completely, remove the  
AC power plug from the wall socket.  
LASER  
Type  
Wave length  
Semiconductor laser GaAlAs  
655 nm (DVD)  
790 nm (VCD/CD)  
0.8 mW (DVD)  
Output Power  
Symbols Used in this Manual  
0.5 mW (VCD/CD)  
The below symbols appear in some headings and notes with  
the following meanings:  
CLASS 1 LASER PRODUCT  
(WARNING LOCA-  
TION: ONTHE  
BACKPLATE OF  
SET)  
DVD-V  
KLASSE 1 LASER PRODUKT  
KLASS 1 LASER APPARAT  
CLASSE 1 PRODUIT LASER  
– Description refers to playback of DVD-video discs  
CD  
– Description refers to playback of Audio CDs  
MP3  
About the PBC Function ofVIDEO CD  
– Description refers to playback of MP3 files  
This unit conforms to ver.1.1 and ver.2.0 ofVIDEO CD standard,  
with PBC function.  
Ver.1.1 (without PBC function):You can enjoy playback picture as  
well as music CD.  
VCD  
– Description refers to playback of video CDs.  
Ver.2.0 (with PBC function):When using aVIDEO CD with PBC  
function,“PBC” appears on the display.  
Helpful Hints!  
• Some DVD video discs require specific functions or allow  
only limited functions during playback.  
What is PBC? “PBC” stands for the  
PlayBack Control.  
You can play interactive software using a menu screens. Refer to  
instructions ofVIDEO CD.  
•
“
” may appears on theTV screen which means that  
the function is not available on that specific DVD video  
disc.  
2
 
Contents  
Introduction  
Programming a Recording (TIMER)  
Environmental Information. . . . . . . . . . . . . . . . . . . . . 2  
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . 2  
General information . . . . . . . . . . . . . . . . . . . . . . . . 12  
Programming a recording  
(with the 'SHOWVIEW® system') . . . . . . . . . . . . . . . 12  
Programming a recording  
(without the SHOWVIEW system) . . . . . . . . . . . . . . 12  
OTR (OneTouch Recording). . . . . . . . . . . . . . . . . . 12  
How to check, or delete  
Functional Overview  
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
a programmed recording (TIMER). . . . . . . . . . . . . 13  
How to change  
a programmed recording (TIMER). . . . . . . . . . . . . 13  
Hints forTimer Recording . . . . . . . . . . . . . . . . . . . 13  
Setting Up your DVD/VCR  
Other Functions  
Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Connecting to aTV . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Simplest connection using only supplied  
black RF coaxial cable . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Connecting to an Audio System(for DVD features) . . 6  
Connecting to Optional Equipment  
Switching the status display off or on . . . . . . . . . . . . 13  
Blue Background on or off . . . . . . . . . . . . . . . . . . . . 13  
Clock Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Selecting the sound channel . . . . . . . . . . . . . . . . . . . 13  
(for DVD features). . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
External Input Mode (forVCR features). . . . . . . . . . . 7  
Inserting batteries into the Remote Control . . . . . . . 7  
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . 7  
PlayableVideo CassetteTapes. . . . . . . . . . . . . . . . . . . 7  
Turning on your DVD/VCR . . . . . . . . . . . . . . . . . . . . . 7  
Video Channel Setting . . . . . . . . . . . . . . . . . . . . . . . . 7  
Automatic Channel Setup. . . . . . . . . . . . . . . . . . . . . . 8  
Manual Channel Preset . . . . . . . . . . . . . . . . . . . . . . . . 8  
FollowTV (AutomaticTV channels sorting). . . . . . . . 8  
Sorting and clearingTV channels manually . . . . . . . . 8  
Setting the language . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Setting the RF out channel . . . . . . . . . . . . . . . . . . . . . 9  
Decoder allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Playing a Disc  
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Disc Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Calling Up a Menu During Playback . . . . . . . . . . . . . 14  
Step by Step Playback . . . . . . . . . . . . . . . . . . . . . . . . 14  
Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . 14  
Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . 14  
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Title / Chapter Search. . . . . . . . . . . . . . . . . . . . . . . . 15  
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
MP3/JPEG Playback . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
On-Screen Information . . . . . . . . . . . . . . . . . . . . . . . 16  
Track Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Audio Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Changing the On-Screen Display . . . . . . . . . . . . . . . 17  
Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . 17  
VCR Playback  
Playing cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Playing back NTSC cassettes . . . . . . . . . . . . . . . . . 10  
Displaying current tape position. . . . . . . . . . . . . . . 10  
Searching for a tape position with picture  
(scanning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Still picture / slow motion. . . . . . . . . . . . . . . . . . . . 10  
Searching for tape position without picture  
(forward wind and rewind) . . . . . . . . . . . . . . . . . . . 10  
Index search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
ManualTracking . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
VCR Manual Recording  
General information . . . . . . . . . . . . . . . . . . . . . . . . 10  
Recording without automatic switch-off . . . . . . . . 10  
Lining up recordings (assemble cut). . . . . . . . . . . . 11  
Selecting the recording speed (SP or LP) . . . . . . . 11  
Automatic controlled recording from a satellite  
receiver (RECORD LINK) . . . . . . . . . . . . . . . . . . . 11  
'Direct Record' . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Switching 'Direct Record' on or off . . . . . . . . . . . . 11  
Direct dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Recording (From DVDToVCR) . . . . . . . . . . . . . . . 11  
DVD Setup  
Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Language Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Information  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
R
SHOWVIEW is a registered trademark of Gemstar Development  
Corporation.  
The SHOWVIEW system is manufactured under licence from  
Gemstar Development Corporation.  
3
 
Functional Overview  
15. VCR light (VCR)  
light appears when DVD/VCR inVCR mode  
16. SOURCE button (DVD,VCR)  
Front Panel  
1
2
3
4
to select between DVD andVCR mode  
OPEN/CLOSE  
17. ySTANDBY-ON button (DVD,VCR)  
to switch the player to ON or OFF  
STANDBY-ON light (DVD,VCR)  
STANDBY-ON  
SOURCE  
DIRECT DUBBING  
STOP  
PLAY  
RECORD  
TIMER  
RECORD  
PLAY  
AUDIO  
VIDEO  
DVD  
VCR  
RECORD  
IR  
light appears when DVD/VCR turns on.  
18. TRK (DVD)  
16 14 12  
13 11  
8
10  
6
5
9
7
17  
15  
Stays on when repeat track function is on.  
19. CHP. (DVD)  
Stays on when repeat chapter function is on.  
20. TITLE (DVD)  
TITLE  
CHP. TRK.  
VCD  
PBC  
REPEAT  
–
A
B
Stays on when repeat title function is on.  
21. REPEAT (DVD)  
Stays on when the repeat function is on.  
22. A-B REPEAT (DVD)  
Stays on when the A-B repeat function is on.  
23. B (DVD,VCR)  
Stays on when the inserted disc or cassette is being played back.  
24. k (DVD,VCR)  
26 27  
18 19 20 21 22 23 24  
25  
1. DiscTray (DVD)  
insert a disc here  
2. A OPEN/CLOSE button (DVD)  
to open/close the disc tray  
3. Cassette Compartment (VCR)  
insert a tape here  
4. A STOP/EJECT button (VCR)  
Lights up when the inserted disc comes to a pause.(DVD)  
Lights up when the playback is in a still or in a slow  
mode.(VCR)  
when playback is stopped, press to eject the tape  
25. Digital Display (DVD,VCR)  
5. AUDIO andVIDEO in jacks  
Displays how long a current title or track has been played  
back.When a chapter or track has switched, the number of a  
new title, chapter or track is displayed.(DVD)  
Works as a clock, or a tape counter. Also displays a channel  
number, and remaining time for OTR.(VCR)  
connect to AUDIO andVIDEO OUT of an audio source  
6. B PLAY button (VCR)  
to play a tape  
7. RECORD button (VCR)  
Press once to start recording, repeatedly to start an One-  
Touch Recording  
26. CD  
Lights up when a CD is inserted on the tray.  
8. RECORD light (VCR)  
VCD  
light appears during recording, it flashes when a recording is  
paused  
Lights up when aVCD is inserted on the tray.  
PBC  
Lights up when aVCD(with PBC function) is inserted on the  
tray.  
27. DVD  
9. RECORDTIMER light (VCR)  
light appears when DVD/VCR is in standby mode for a timer  
recording(also light appears during timer recording)  
Lights up when a DVD is inserted on the tray.  
10. IR (Infrared) Remote Sensor (DVD,VCR)  
receive signals from remote control  
11. B PLAY button (DVD)  
to start, pause or resume disc playback  
12. C STOP button (DVD)  
Display Message  
to stop playback  
Appears after the disc tray closes if the tray is empty, if  
there is an error reading the disc, or if an unacceptable  
disc is installed.  
13. DIRECT DUBBING button (VCR)  
to play DVD disc and record its’ content to video cassette  
tape at the same time  
Tray is opening or is open.  
14. DVD light (DVD)  
light appears when DVD/VCR in DVD mode  
Tray is closing. This also may appear as the Player tries  
to load a Disc.  
Rear Panel  
Disc is loading.  
DVD OUTPUT ONLY  
AV2 (DECODER)  
4. AV1 (TV) jack  
S-VIDEO  
OUT  
ANALOG  
DIGITAL  
VCR  
AUDIO OUT  
AUDIO OUT  
AERIAL  
RF OUT  
connect SCART cable to a TV  
5. S-Video Out jack (DVD only)  
DVD/VCR  
AV1 (TV)  
L
COAXIAL OPTICAL  
R
connect to a TV with S-Video inputs  
6. AUDIO OUT (Left/Right) jacks (DVD only)  
connect to AUDIO inputs of an amplifier, receiver or stereo  
system  
7. COAXIAL (Digital audio out) jack (DVD only)  
connect to AUDIO inputs of a digital (coaxial) audio equip-  
ment  
1
2
3
4
5 6 7 8  
9
1. RF OUT jack  
use supplied RF coaxial cable to connect to the ANTENNA  
IN on your TV, cable box or Direct Broadcast System  
2. AERIAL jack  
8. OPTICAL (Digital audio out) jack (DVD only)  
connect to an antenna or cable  
connect to digital (optical) audio equipment  
3. AV2 (DECODER) jack (VCR only)  
connect SCART cable from another DVD/VCR, camcoder or  
an audio/video source  
9. MAINS (AC Power Cord)  
connect to a standard AC outlet  
4
 
Functional Overview  
8.  
h
to view DVD picture in fast reverse motion (DVD)  
to rewind the tape (VCR)  
Remote Control  
9. STOP ( C )  
STANDBY-ON  
to stop a DVD disc playback (DVD)  
to stop playback, recording(VCR)  
10. PLAY ( B )  
1
OPEN/CLOSE  
to start a DVD disc playback (DVD)  
to start a tape playback(VCR)  
11. SV/V+  
to programme timer recording with the SHOWVIEW system  
(VCR)  
12. TITLE  
to display title menu of a disc (DVD)  
13. ANGLE  
select DVD camera angle (DVD)  
14. MODE  
1
2
5
8
0
3
6
33  
32  
EJECT  
4
+
SKIP / P  
2
7
9
DISPLAY  
CLEAR  
+10  
31  
30  
STATUS/EXIT  
3
4
SYSTEM  
VCR  
DVD  
29  
to set up programmed or random playback (Audio CD)  
15. REPEAT  
SYSTEM  
DISC/VCR  
MENU  
MENU  
28  
5
6
7
repeat chapter, track, title, disc (DVD)  
16. TIMER SET  
to put the DVD/VCR into standby mode for a timer recording  
17. INDEX SEARCH  
OK  
to fast forward or rewind the tape at index number (VCR)  
18. SUBTITLE  
subtitle language DVD selector (DVD)  
19. SEARCH MODE  
to access or remove search display (DVD)  
20. REPEAT (A-B)  
repeat a specific segment (DVD)  
21. ZOOM  
enlarge DVD video image (DVD)  
22. RETURN  
to return previous or remove setup menu (DVD)  
23. AUDIO  
to choose audio languages or sound modes (DVD)  
to choose sound modes (VCR)  
24. SLOW  
8
27  
26  
STOP  
PLAY  
PAUSE  
9
10  
SV / V+  
SLOW  
RECORD  
11  
25  
24  
23  
22  
21  
20  
19  
TITLE  
MODE  
TIMER  
SET  
ANGLE  
RETURN  
AUDIO  
ZOOM  
12  
13  
REPEAT REPEAT  
A-B  
14  
15  
INDEX SUBTITLE SEARCH  
16  
17  
MODE  
18  
to view tape playback in slow motion (VCR)  
25. RECORD  
to record the TV channel selected at this moment or press  
repeatedly to start a One-Touch Recording (VCR)  
26. PAUSE ( k )  
pause playback temporarily / frame-by-frame playback (DVD)  
pause playback and during recording temporarily (VCR)  
g
27.  
to view DVD picture in fast forward motion (DVD)  
to fast forward the tape (VCR)  
28. DISC/VCR MENU  
to display the menu of the DVD disc or to accessVCR menu  
1. ySTANDBY-ON  
switch DVD/VCR ON or OFF  
29. VCR  
press to put the DVD/VCR inVCR mode and before using  
the remote control forVCR features  
2. 0-9 numerical key pad/+10  
select numbered items in a menu  
use +10 button to enter number 10 and above (DVD)  
to select TV channels inVCR mode  
3. SYSTEM  
doesn’t work on this model  
4. DVD  
30. DISPLAY STATUS/EXIT  
to access or remove the display screen during DVD or Audio  
CD playback(DVD)  
to access or removeVCR’s on-screen status display(VCR)  
to removeVCR’s menu(VCR)  
31. CLEAR  
press to put the DVD/VCR in DVD mode and before using  
the remote control for DVD features  
to reset the setting (DVD)  
to reset the counter (VCR)  
to delete last entry/Clear programmed recording (TIMER)  
(VCR)  
5. SYSTEM MENU  
to access or remove the DVD setup menu (DVD)  
6. OK  
32. SKIP/P (j/ – /i/ + )  
to skip chapter/tracks (DVD)  
to change TV channels (VCR)  
acknowledge menu selection (DVD)  
7.  
{
B
K
L
(left/right/up/down) select an item in the menu  
33. OPEN/CLOSE EJECT  
to insert discs into or remove them from the tray (DVD)  
to remove the tape from theVCR (VCR)  
5
 
Setting Up your DVD/VCR  
Simplest connection using only supplied  
black RF coaxial cable  
Disconnect the antenna or cable from your TV.  
Connect the antenna or cable to the AERIAL of your DVD/VCR.  
Connect black RF coaxial cable to the RF OUT on the rear  
panel of the DVD/VCR and to the ANTENNA IN on the TV.  
Plug in the power cords of the TV and DVD/VCR.  
Basic Connections  
• Please refer to the instruction books of your TV,VCR, Stereo  
System or other devices as necessary to make the best con-  
nections.  
• Make one of the following connections, depending on the  
capabilities of your existing equipment.  
The following guidelines are options for the best picture and  
sound quality available on your DVD/VCR.  
1
2
3
4
Antenna In  
Back of DVD/VCR  
(on back ofTV)  
example only  
Antenna  
Indoor/Outdoor  
(300 ohm)  
Picture  
DVD OUTPUT ONLY  
1
2
3
4
Use SCART RGB Output (DVD/VCR(AV1 TV)) for best pic-  
ture quality (for DVD features).  
AV2 (DECODER)  
VCR  
S-VIDEO  
OUT  
ANALOG  
DIGITAL  
AERIAL  
RF OUT  
AUDIO OUT  
AUDIO OUT  
DVD/VCR  
AV1 (TV)  
L
COAXIAL OPTICAL  
R
Use S-VIDEO Output for the better picture quality (for DVD  
features only).  
Use SCART Composite Output for good picture quality (for  
DVD andVCR features).  
If your TV only has a RF-style (Antenna IN or 75 ohm) input,  
use the RF OUT for connection and set your TV to channel  
22 ~ 69 with the same channel for DVD/VCR is set (for DVD  
andVCR features).  
1
L/MONO  
AUDIO  
R
AERIAL  
RF OUT  
VIDEO  
in  
OR  
75  
ANT  
CABLE  
Cable  
(75 ohm)  
Black RF  
coaxial cable  
(Supplied)  
Sound  
Connecting to an Audio System(for DVD  
features)  
You can also listen to the sound of audio CDs and DVD video  
discs by connecting to an optional stereo system.  
Connect DVD/VCR ANALOG AUDIO OUT (Left and Right)  
to the audio in on the stereo system.  
1
2
Digital audio connections provide the clearest sound. Connect  
the DVD/VCR DIGITAL AUDIO OUT (either COAXIAL or  
OPTICAL) to your amplifier or receiver (for DVD features only).  
Use SCART Output (DVD/VCR(AV1 TV)) for better sound  
quality (for DVD andVCR features).  
If digital connections are not possible, connect the DVD/VCR  
ANALOG AUDIO OUT(Left and Right) to your amplifier,  
receiver, stereo or TV (for DVD features only).  
1
2
STEREO  
Warning!  
– Never make or change connections with the power  
switched on.  
– Connect the DVD/VCR directly to yourTV, instead of eg.  
a VCR, to avoid distortion because DVD video discs are  
copy protected.  
AUDIO (LEFT) IN  
AUDIO (RIGHT) IN  
– Do not connect the ANALOG AUDIO OUT of DVD/VCR  
to PHONO IN of your amplifier or receiver.  
– If you use the Euro audio/video cable, it is not necessary  
to connect the analog audio cable.  
DVD OUTPUT ONLY  
AV2 (DECODER)  
S-VIDEO  
OUT  
ANALOG  
DIGITAL  
VCR  
AUDIO OUT  
AUDIO OUT  
AERIAL  
RF OUT  
DVD/VCR  
AV1 (TV)  
L
COAXIAL OPTICAL  
R
Connecting to aTV  
1
2
Connect the antenna or cable to the AERIAL of your DVD/VCR.  
Connect the DVD/VCR (AV1 TV) on the DVD/VCR to the  
corresponding connector on the TV.  
Connecting to Optional Equipment (for  
DVD features)  
• A digital component with a built-in MPEG 2 or Dolby  
Digital decoder allows you to enjoy the surround sound  
while producing the effect of being in a movie theater or a  
concert hall.  
•The player outputs the surround sound signals from the DIG-  
ITAL OUT COAXIAL or OPTICAL connector.  
Note:  
TM  
– Ensure that the “TV” indication on SCART cable is con-  
nected to theTV set and “DVD” indication on SCART  
cable is connected to the DVD/VCR.  
If your TV is not equipped with a SCART input, you can select  
the following connection:  
If yourTV has a S-Video input connector,  
Connect the antenna or cable to the AERIAL of your DVD/VCR.  
Connect the S-Video out on the DVD/VCR to the S-Video in  
on the TV.  
Connect the ANALOG AUDIO OUT on the DVD/VCR to the  
Left and Right audio in on the TV.  
If your receiver has a MPEG 2 or Dolby Digital™ decoder,  
Connect the COAXIAL or OPTICAL DIGITAL AUDIO OUT  
of the DVD/VCR to the COAXIAL or OPTICAL DIGITAL  
AUDIO IN on your receiver.  
1
2
1
3
Note:  
– If the audio format of the digital output does not match  
the capabilities of your receiver, the receiver will pro-  
duce a strong, distorted sound or no sound at all.  
– MP3 Audio is not available on the Digital Output.  
– You will still need the video cable or RF coaxial cable for  
VCR features.  
ANTENNA IN  
OR  
AUDIO RECEIVER  
OPTICAL DIGITAL  
AUDIO IN  
DVD OUTPUT ONLY  
AV2 (DECODER)  
S-VIDEO  
OUT  
ANALOG  
DIGITAL  
VCR  
AUDIO OUT  
AUDIO OUT  
AERIAL  
RF OUT  
COAXIAL DIGITAL  
AUDIO IN  
DVD/VCR  
AV1 (TV)  
L
COAXIAL OPTICAL  
R
Note:  
DVD OUTPUT ONLY  
AV2 (DECODER)  
S-VIDEO  
OUT  
ANALOG  
DIGITAL  
VCR  
AUDIO OUT  
AUDIO OUT  
AERIAL  
RF OUT  
– You will still need the SCART cable or RF coaxial cable  
for VCR features.  
DVD/VCR  
AV1 (TV)  
L
COAXIAL OPTICAL  
R
6
 
Setting Up your DVD/VCR  
External Input Mode (forVCR features)  
Turning on your DVD/VCR  
To receive the signal from an external input (decoder, satellite  
receiver, video camera, anotherVCR etc.), connect to the AV2  
(DECODER) socket, and enter “002” with numerical key pads  
button to appear “AV2” on the TV screen.  
If you use the AV1 (TV) socket, enter “001” with numerical key  
pads to appear “AV1” on the TV screen.  
The following steps only be performed when you insert the AC  
PLUG at the first time.  
SELECT  
K
L
1
Turn on the TV and select the  
video channel on the TV.  
Plug in the DVD/VCR.  
Press K/L repeatedly to select  
your desired language.  
Press DISC/VCR MENU.  
Confirm with P+.  
¡ ENGLISH  
FRANÇAIS  
2
3
ESPAÑOL  
DEUTSCH  
ITALIANO  
If you use the front AUDIO/VIDEO input jacks, enter “003” with  
numerical key pads to appear “AV3” on the TV screen.  
SVENSKA  
NEDERLANDS  
PUSH MENU TO CONTINUE  
4
5
The automatic TV channel search  
starts.  
'TIME' and 'DATE' will appear on  
the TV screen.  
Check 'TIME'. If required, please  
change the time with numerical key  
pads.  
Check if the displayed settings for  
'DAY', 'MONTH' and 'YEAR' are  
correct.  
When all information is correct,  
save by pressing STATUS/EXIT.The  
preparation for use is now com-  
plete.  
Inserting batteries into the Remote Control  
1
2
Open the battery cover.  
Insert batteries (AA size) with the  
correct polarity as indicated by the  
+ and - symbols inside the battery  
compartment.  
PLEASE WAIT  
6
7
START  
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚  
FINISH  
3
Close the cover.  
8
9
CAUTION!  
– Remove batteries if they are exhausted or not to be used  
for a long time.  
– Do not use old and new or different types of batteries in  
combination.  
– Batteries contain chemical substances, so they should be  
disposed off properly and kept away from children.  
TIME --:--  
DATE --/--/--  
SMART CLOCK [ON]  
END=EXIT  
Notes:  
Using the Remote Control  
– If the DVD/VCR has been completed AUTOTUNING at  
this procedure, this initial menu has never shown even if  
power failure is occured or inserted AC plug again.)  
• Direct the remote control at the remote sensor of the  
DVD/VCR.  
• Do not drop the remote control.  
• Do not leave the remote control near extremely hot or  
humid place.  
• Do not spill water or put anything wet on the remote con-  
trol.  
Video Channel Setting  
Video channel setting will be necessary, if your DVD/VCR is  
connected to the TV via the coaxial cable.  
Insert a pre-recorded tape into the DVD/VCR.The DVD/VCR  
will turn on and start playback automatically.  
If playback does not start, press PLAY B .  
Select and adjust your TV to channel 36.  
• If the playback picture appears on the TV screen, continue  
with step 8.  
• If channel 36 is employed for broadcasting, or interference  
lines appear on the picture, the RF converter must be set to  
a different channel between CH22 and CH69. Continue with  
step 3.  
PlayableVideo CassetteTapes  
Philips Consume Electronics recommends that only video cas-  
sette tapes that have theVHS mark and High Quality (HQ) sys-  
tem is compatible with this DVD/VCR.This  
1
2
DVD/VCR has an Automatic Head Cleaner.  
Recording Prevention  
Video cassette tapes have record tabs to  
ensure recordings are not erased accidentally.  
To prevent recording, break off the tab with a  
screw-driver.  
To allow recording, cover the hole with cello-  
phane tape.  
1
1
2
3
4
Press DISC/VCR MENU.  
2
Press K/L to select INITIAL SET  
UP.Then, press B.  
SELECT  
K
L
CHOOSE  
B
Notes:  
– Use only tapes with VHS mark.  
¡ RF OUT CH 36  
5
6
Press K/L to select RF OUT.Then,  
press B twice.  
– Remove any adhesive stick-on notes from the tape  
before inserting into the DVD/VCR.  
– Periodic maintenance is required to maintain your  
DVD/VCR performance.  
– Video heads will require replacement after a period of  
time. Only an authorised service center should perform  
this service.  
Press K/L to select a channel  
which is not used for broadcasted  
between channel 22 and channel 69  
in your area, then press B.  
SET=0-9  
END=EXIT  
•You can also see the selecting RF channel in the display  
Press STATUS/EXIT to exit.  
7
8
Set the TV channel to the RF OUT CHANNEL which was  
selected on the DVD/VCR.A picture from theVCR will appear  
on the TV screen. If a picture does not appear, repeat steps 3  
to 7 using a different channel which is not used for broadcast-  
ed.  
Press STOP C to stop the tape.  
Note:  
– You may also access the RF OUT CH menu by pressing  
and holding DISC/VCR MENU for 3 seconds during power  
off until the RF OUT CH menu appears.  
7
 
Setting Up your DVD/VCR  
I cannot switch myTV set to programme number '1'  
* If you have connected additional devices to socket  
AV2(DECODER), please disconnect these devices. Because of  
other connected devices, the TV set could switch to the pro-  
gramme number of the scart socket.  
Automatic Channel Setup  
You can programme the tuner to scan only the channels that  
you can receive in your area.  
Turn on the TV and select the video out channel on your TV.  
PressVCR, then DISC/VCR MENU.  
Press K/L to select TUNER SET UP, then press B.  
Press K/L to select AUTO TUN-  
1
2
3
4
'NOTV SIGNAL' will appear in theTV screen.The  
DVD/VCR is not receiving a video signal from theTV.  
Check the plug on the scart cable.  
Check your TV's operating instructions to see which scart socket  
is used for video signals.  
If this does not help, it's not possible to use this function. Please  
read the section 'Sorting TV channels manually'.  
ING, then press B.  
•The tuner scans and memorizes  
PLEASE WAIT  
all the active channels in your  
START FINISH  
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚  
area.After scanning, the tuner  
stops on the lowest memorized  
channel.  
5
6
Select programme number '1' on the TV.  
Confirm with B on the DVD/VCR remote control.The  
DVD/VCR compares the TV channels on the TV and the  
DVD/VCR.  
5
Press P +/– or numerical key pads  
to scan through channels you have received.  
If the DVD/VCR finds the same TV channel as on the TV, then  
it stores it at 'P01'.  
Wait until the next number, e.g. 'P:02' appears in the display.  
Select the next programme number on the TV, e.g. '2'.  
Confirm with B.  
Manual Channel Preset  
PressVCR, then DISC/VCR MENU.  
Press K/L to select TUNER SET UP, then press B.  
Press K/L to select MANUAL  
TUNING, then press B.  
Press K/L to select PROG., then  
press B.  
Press K/L or numerical key pads  
7
8
9
1
2
3
10 Repeat steps 7 to 9 until you have assigned a programme num-  
ber to all TV channels.  
11 To end, press STATUS/EXIT.  
MANUAL TUNING  
¡PROG.  
CHANNEL  
DECODER  
SKIP  
P55  
4
5
055  
[OFF]  
[OFF]  
to select your desired programme SET=K  
number, then press B.  
L
OR 0 – 9  
Sorting and clearingTV channels manually  
END=EXIT  
After you have performed the automatic channel search you  
may not agree with the sequence in which the individual TV  
channels have been allocated to the programme positions (pro-  
gramme numbers) of the DVD/VCR.You can use this function  
to individually sort the TV channels already saved or to delete  
unwanted TV channels or those with poor reception.  
•You can select programme number 01-99.  
6
7
Press K/L to select CHANNEL, then press  
B.  
Press K/L.The DVD/VCR tuner will begin to search up or  
down automatically.When a channel is found, the DVD/VCR  
will stop searching and the picture will appear on the TV  
Screen.  
•You can select desired channel number by using numerical  
key pads.You must refer to the channel plan and press three  
digits to select the channel number. (To select channel 24,  
first press “0” button then press “2” and “4”).  
• If this is the channel you want, press B.  
The clock resets automatically  
If you save a TV channel that transmits TXT/PDC on programme  
number ‘P01’, date and time will constantly be updated.As a result,  
time changes, i.e. daylight savings time, will be set automatically.  
1
2
3
4
PressVCR, then DISC/VCR MENU.  
MOVE  
¡P01: 02  
P02: 03  
P03: 05  
P04: 10  
P05: 74  
P06: 90  
P07: 99  
P08: 121  
P09: 124  
P10: 130  
• If you want to remove scrambled signals, press K/L to select  
DECODER.Then, press B to select [ON].  
Press STATUS/EXIT to exit.  
Press K/L to select 'TUNER SET  
UP' , then press B.  
Press K/L to select 'MOVE' , then  
press B.  
Press K/L to select the saved TV  
channel that you want to change.  
Confirm with B.  
8
Note:  
SELECT  
K
L
CHOOSE  
B
–To confirm that a channel has been added, press the P  
+/– buttons.  
– You should select the satellite channels to be received by  
the satellite receiver directly on the receiver itself.  
END=EXIT  
5
6
Move the selected channel with K/L to the programme num-  
ber you want to assign.  
7
8
Confirm with B.  
To assign other TV channels to a programme number, repeat  
steps 4 to 7.  
FollowTV (AutomaticTV channels sorting)  
When the automatic channel search function is activated, the  
TV channels are saved in a specific order.This may vary from  
the order of TV channels on the TV.  
9
Confirm the assignment of the TV channel with MOVE menu.  
10 To exit the MOVE menu, press STATUS/EXIT.  
This function changes the order of TV channels saved in the  
DVD/VCR to match that of the TV.  
Make sure that the DVD/VCR and the TV are connected by a  
scart cable.  
Setting the language  
You have the option of setting one of the displayed languages  
for the on-screen menu (OSD). However, the DVD/VCR dis-  
play will only display English text regardless of this setting.  
1
2
3
4
PressVCR, then DISC/VCR MENU.  
1
2
3
4
5
PressVCR, then DISC/VCR MENU.  
SELECT  
K
L
CHOOSE  
B
SELECT  
K
L
AUTO TUNING  
MANUAL TUNING  
¡FOLLOW TV  
MOVE  
¡ ENGLISH  
FRANÇAIS  
ESPAÑOL  
DEUTSCH  
ITALIANO  
SVENSKA  
Press K/L to select TUNER SET  
UP, then press B.  
Press K/L to select 'FOLLOW TV'  
, then press B.  
'P:01' will appear in the DVD/VCR  
display.  
Press K/L to select 'INITIAL SET  
UP' , then press B.  
Press K/L to select 'LANGUAGE'  
, then press B.  
Select the desired language with  
K/L.  
To end, press STATUS/EXIT.  
END=EXIT  
NEDERLANDS  
END=EXIT  
8
 
Setting Up your DVD/VCR  
Setting the clock  
Decoder allocation  
If the display shows an incorrect time or ' --:-- ', the time and  
date must be reset manually.  
If a TV channel that transmits TXT/PDC (teletext/PDC) is  
stored under programme number 'P01', time/date will automat-  
ically be taken from the TXT/PDC information. (SMART  
CLOCK)  
Some TV channels transmit encoded TV signals which can only  
be viewed with a purchased or rented decoder.You can con-  
nect such a decoder to this DVD/VCR.The following function  
will automatically activate the connected decoder for the  
desired TV channel.  
Switch the TV on. If applicable, select the programme number  
for the DVD/VCR operation.  
Press K/L or numerical key pads to select the TV channel  
which you would like to allocate the decoder to.  
Press DISC/VCR MENU.The main menu will appear.  
Press K/L to select 'TUNER SET UP'.Then press B.  
1
2
1
PressVCR, then DISC/VCR MENU.  
2
3
4
Press K/L to select 'INITIAL SET UP' , then press B.  
Press K/L to select 'CLOCK' , then press B.  
Check the time in 'TIME'. If  
3
4
required, please change the time  
with numerical key pads.  
Check 'DAY', 'MONTH' and 'YEAR'  
TIME --:--  
MANUAL TUNING  
5
Press K/L to select 'MANUAL  
DATE --/--/--  
5
6
7
TUNING'.Then press B.  
PROG.  
CHANNEL  
¡DECODER  
SKIP  
P55  
in the same way.  
Choose ‘SMART CLOCK’ ON or  
6
7
Press K/L to select 'DECODER'.  
Press B to select 'ON' (Decoder  
switched on).  
SMART CLOCK [ON]  
055  
[OFF]  
[OFF]  
OFF with B.  
To end, press STATUS/EXIT.  
END=EXIT  
SELECT  
K
L
CHOOSE  
B
END=EXIT  
How can I switch off the decoder?  
Use B to select 'OFF' (Decoder switched off).  
Setting the RF out channel  
In some reception locations it is possible that a TV channel will  
be sent on the same or similar frequency as the DVD/VCR.  
Result:As soon as the DVD/VCR is switched on, the reception  
quality for this or several other TV channels will decrease.  
The following steps will show you how to change the pre-set  
'transmission' (RF out channel) frequency on the DVD/VCR.  
PressVCR, then DISC/VCR MENU.  
8
To end, press STATUS/EXIT.  
The decoder has now been allocated to this TV channel.  
1
2
Press K/L to select 'INITIAL SET UP' , then press B.  
What is RF out channel?  
This electronic component in the DVD/VCR allows the device to  
transmit audio and video signals via the aerial cable.These signals  
can be received on a TV set just like TV channels.  
What is RF out channel frequency?  
This frequency or channel indicates the channel on which the  
audio or video signal is transmitted.  
3
Press K/L to select 'RF OUT' ,  
then press B.  
Press B.  
Press K/L or numerical key pads  
to select a free (not allocated)  
channel between channel 22 and 69  
in your area.  
SELECT  
K
L
CHOOSE  
36  
B
4
5
¡RF OUT CH  
END=EXIT  
6
7
Press B.  
To end, press STATUS/EXIT.  
If you cannot get an interference-free picture and sound, switch  
the built-in modulator off.  
Press L repeatedly until "--" appears next to "RF OUT CH" on  
the TV screen.  
Then confirm with B. In that case, please connect yourVCR to  
your TV with a Scart cable.  
9
 
VCR Playback  
Playing cassettes  
Searching for a tape position with picture  
(scanning)  
You can use this DVD/VCR to play back recordedVHS video-  
cassettes.You can operate the DVD/VCR using the remote  
control or the buttons on the front of the DVD/VCR.  
If you press PLAY, STOP, FWD or REW while the set is in  
Stand-by, the power will be automatically turned on.  
Additionally, if a cassette was already inserted, the correspond-  
ing operation will be performed.  
1
2
While a cassette is playing, press  
ward) one or more times.  
(rewind) or  
(for-  
h
g
Press PLAY B to resume playback.  
Your DVD/VCR can only record and play standardVHS cas-  
settes.  
Put a cassette into the cassette slot.The cassette is inserted  
automatically.  
Press PLAY to view the tape.  
To stop the playback, press STOP or STOP/EJECT on the DVD/  
VCR.  
Still picture / slow motion  
1
During playback, press PAUSE  
still picture.  
to stop the tape and display a  
k
1
2
3
During playback, press SLOW to play the tape in slow motion.  
Press PLAY B to resume playback.  
Scanning and still/slow motion interferes with the picture quali-  
ty.The sound is switched off.This is not a fault in your  
DVD/VCR.  
2
3
4
To eject the cassette, press EJECT or STOP/EJECT on the  
DVD/VCR when the DVD/VCR stops the playback.  
DIGITAL STUDIO PICTURE CONTROL  
Philips has developed a system which produces the best possible  
playback quality. For old and often-used video cassettes, this sys-  
tem reduces interference. For new or high quality cassettes, it  
emphasises the details.  
Searching for tape position without picture  
(forward wind and rewind)  
1
2
3
Stop the tape with STOP  
.
C
g
Press  
(rewind) or  
(forward).  
h
Picture/ sound quality is poor  
To stop the tape, press STOP C.  
When playing rental videos or older, poorer quality cassettes, it  
may not be possible to completely filter out picture and sound  
interference.This is not a fault in your machine. Read the section  
'VCR Manual tracking'.  
Index search  
Every time a tape is recorded an index marking is written on  
Do I need to change the playback speed when playing  
back LP recordings?  
During playback, the correct speed will automatically be selected.  
For more information, please read the section 'Selecting the  
recording speed (SP or LP)' in the chapter 'VCR Manual record-  
ing'.  
the tape.  
These marked positions can be found again quickly and easily  
later.  
To search for the previous marking, press INDEX 3 and then  
1
.
h
2
3
For the next marking, press INDEX 3 and then  
As soon as the DVD/VCR finds this marking, it automatically  
switches to playback.  
.
g
Playing back NTSC cassettes  
This DVD/VCR can also play back cassettes that have been  
recorded in SP [Standard Play] or SLP [Super Long Play] mode  
in the NTSC standard (for example,American cassettes).  
However, this only works on PAL-television sets that are suit-  
able for a picture frequency of 60Hz.  
ManualTracking  
To manually adjust the tracking during playback and slow  
motion playback, press P+ or P-.  
Tracking will return to Automatic Tracking Adjustment when  
you press STOP C, insert a tape, or press PLAY B.  
To remove vertical jitter in a Still picture, press P+ or P-.  
Displaying current tape position  
The following information is displayed on the screen: e.g.:  
0:02:45 shows the counter in hours, minutes and seconds.  
SP/LP: will show the recorded speed of your cassette  
'REM 0:06': will show the actual amount of playing/recording  
time left on the tape in hours and minutes.  
When you play an NTSC cassette, the DVD/VCR will show  
'REM -:--'.  
General information  
Use 'Manual Recording' to make a spontaneous recording  
(for example, a programme currently being shown).  
If you want to start and stop a recording manually, read the  
section 'Recording without automatic switch-off'.  
If you want to start a recording manually but have it stopped  
automatically, read the section  
Read the section 'Direct record' if you want to record a pro-  
gramme currently being shown.  
Read the section 'Automatic controlled recording from a  
satellite receiver (RECORD LINK)', if you want a record-  
ing to be controlled automatically by a satellite receiver.  
How can I set the counter to '0:00:00'?  
You can set the counter to '0:00:00' with CLEAR.  
When you put a cassette in the DVD/VCR, the counter will auto-  
matically reset to '0:00:00'.  
The counter does not move  
This occurs when there are no recordings on a portion of a tape.  
This is not a fault in your DVD/VCR.  
The screen shows '-0:01:20'  
If you rewind a cassette from the tape position '0:00:00', the  
counter will show for instance, '-0:01:20' (the cassette was  
rewound to 1 minute and 20 seconds before '0:00:00').  
('-'(minus) is not shown in the display.)  
Recording without automatic switch-off  
Insert a cassette.  
Use P+/P- to select the programme number you want to  
record, for example, 'P01'.  
To start recording, press RECORD I.  
Stop recording with STOP C.  
1
2
'-:--' is displayed in the 'REM' counter  
This counter will automatically recognise the length of the tape. In  
addition, when you put in a cassette the DVD/VCR must first cal-  
culate the time played.Therefore, '-:--' appears first and only after  
the tape has been running for a few seconds, the correct playing  
time will be shown.  
3
4
10  
 
VCR Manual Recording  
Linking up recordings (assemble cut)  
'Direct Record'  
When you add a further recording to a cassette, which already  
has a recording on it, a short blank (flicker) can appear between  
the old and the new recording or the picture itself can flicker.  
To help reduce these from occurring, proceed as follows:  
Find the tape position of the old recording where you want to  
insert the new recording.  
With Direct Record, you can record the right TV channel in  
seconds even if your DVD/VCR is switched off. If the recording  
is started manually, the DVD/VCR uses the current TV channel  
set on the TV.You will find more information on how to switch  
'Direct Record' on or off in the next section. Make sure that  
your DVD/VCR socket (AV1/TV) and the TV are connected by  
a scart cable.  
On the TV, select the programme number you want make the  
recording from.  
Press RECORD I with the DVD/VCR switched off.  
Stop recording with STOP C.  
1
2
3
Look at the last minute of the old recording (playback).  
Press PAUSE  
at the tape position where the new recording  
1
k
is to go and press RECORD I.  
Now start recording as usual by pressing RECORD I on the  
remote control.  
4
5
2
3
Stop recording with STOP C.  
How does Direct Record work?  
The DVD/VCR compares the TV channel selected on the TV set  
with its stored TV channels via the scart cable. If the same TV  
channel is found, it switches the DVD/VCR to the corresponding  
programme number and starts recording. Please do not change  
the TV channel on the TV set during the search so as not to  
affect the process.  
Selecting the recording speed (SP or LP)  
LP allows to double the recording duration on tape (for exam-  
ple six hours instead of three hours on an E180 cassette).  
Switch on the TV set. If required, select the programme num-  
ber for the DVD/VCR.  
1
2
3
SELECT  
K
L
CHOOSE  
B
Press DISC/VCR MENU.The main  
menu will appear.  
Select 'RECORD SETUP' using  
K/L and confirm with B.  
Select 'RECORD SPEED' using K/L.  
Select the required recording  
speed with B.  
¡RECORD SPEED [SP]  
Switching 'Direct Record' on or off  
DIRECT RECORD [OFF]  
1
Switch on the TV. If required, select the programme number for  
the DVD/VCR.  
RECORD LINK  
[OFF]  
4
5
2
3
Press DISC/VCR MENU.The main menu will appear.  
Select 'RECORD SET UP' with  
SELECT  
K
L
CHOOSE  
B
END=EXIT  
K/L and confirm with B.  
In 'DIRECT RECORD', select 'OFF'  
(Direct Record off) or 'ON'  
(Direct Record on) with B.  
To end, press STATUS/EXIT.  
Press STANDBY-ON.  
RECORD SPEED [SP]  
4
¡DIRECT RECORD [OFF]  
'SP'/'LP' /'AUTO'  
'SP': StandardPlay (normal recording speed) offers the usual first-  
class picture quality.  
'LP': LongPlay (half recording speed, double recording time). 6  
hours can be recorded on a 3-hour cassette (E180) with a some-  
what reduced picture quality.  
RECORD LINK  
[OFF]  
5
6
END=EXIT  
'AUTO':AUTOmatic Long Play. If there is not enough space on  
the tape to record a programmed recording in standard speed,  
the recording is automatically done in 'LP'  
Direct dubbing  
Follow the steps below to copy a DVD or video disc to a  
videotape.This will be possible only if the DVD is not copy  
protected.  
Put a videotape in the cassette compartment. Make sure the  
tape’s record tab is intact and the tape is long enough to  
record the disc.  
(Longplay). Otherwise, the recording speed will be 'SP'  
(Standardplay).  
6
To end, press STATUS/EXIT.  
1
Automatic controlled recording from a  
satellite receiver (RECORD LINK)  
This function automatically starts recording on the switched-off  
DVD/VCR when a video signal is recognised through the con-  
nected scart cable. If your satellite receiver has a programming  
function, the recording will start automatically (as long as the  
satellite receiver is switched on).  
Use a scart cable to connect scart socket AV2(DECODER) on  
the DVD/VCR to the corresponding scart socket on the satel-  
lite receiver.  
Switch on the TV. If required, select the programme number for  
the DVD/VCR.  
2
3
PressVCR.  
Select the recording speed.  
Details are at “Selecting the recording speed (SP or LP)”.  
Put the DVD you want to copy in the disc tray.  
Press DVD.  
Press PLAY B.While disc is playing, press PAUSE k at the  
point you wish to start recording.  
Press DIRECT DUBBING to record.  
To pause the recording.  
Press PAUSE k.  
To resume recording.  
Press PAUSE k again.  
To stop the recording.  
4
5
6
7
1
2
3
4
5
6
7
8
9
Press DISC/VCR MENU.The main menu will appear.  
Select 'RECORD SET UP' with K/L and confirm with B.  
Select 'RECORD LINK' with K/L.  
Press STOP C.  
SELECT  
K
L
CHOOSE  
B
Select function 'ON' with B.  
To end, press STATUS/EXIT.  
Insert a cassette.  
Programme the satellite receiver  
with the required information (pro-  
gramme number of the TV channel,  
start time, end time).  
RECORD SPEED [SP]  
DIRECT RECORD [OFF]  
Recording(From DVDToVCR)  
Insert a DVD without copyright protection in the tray.  
Insert a video cassette tape with its erase prevention tab in  
place.  
1
2
¡RECORD LINK  
[OFF]  
3
4
Select the recording speed.  
END=EXIT  
Details are at “Selecting the recording speed (SP or LP)”.  
Enter “004” with numerical key pads to appear “DISC” on the  
TV screen.  
Press RECORD I.  
Change to DVD operation mode.  
Press DVD, then PLAY B to begin the playback of a DVD.  
PressVCR, then STOP C to stop recording.  
If necessary, please see the operating instructions for your  
satellite receiver.  
5
6
7
8
10 Press TIMER SET.  
The DVD/VCR is now ready to record.The beginning and end  
of the recording is controlled via scart socket  
AV2(DECODER).  
11  
 
Programming a Recording (TIMER)  
5
6
The decoded data appears after confirmation.You can go back  
to change the data. Select the corresponding input field using  
B or CLEAR. Change the data with numerical key pad.  
When all inputs are correct, press STATUS/EXIT.The program-  
ming information is stored in a Timer block.  
General information  
Use a TIMER programming to automatically start and stop a  
recording at a later time or date.The DVD/VCR will switch to  
the right programme number and begin recording at the cor-  
rect time.With this DVD/VCR, you can pre-programme up to  
eight recordings within a period of one year.To make a pro-  
grammed recording, your DVD/VCR needs to know:  
* the date you want to make the recording  
Switching on 'VPS/PDC' in the 'START' input field  
Select 'VPS/PDC' using B or CLEAR. Press '1' to switch off  
'VPS/PDC' or press '2' to switch on 'VPS/PDC'.  
* the programme number of the TV channel  
* the start and stop time of the recording  
*VPS or PDC on or off  
This information is saved in a TIMER block.  
7
8
Insert a cassette with an intact security tab (unprotected).  
Press TIMER SET.  
'RECORD TIMER' will light up on the DVD/VCR display.  
What is 'VPS/PDC'?  
'VPS' (Video Programming System)/ 'PDC' (Programme Delivery  
Control) are used to control the start and duration of TV channel  
recordings. If a TV programme starts earlier or ends later than  
scheduled, the DVD/VCR will turn on and off at the correct time.  
What do I need to know about 'VPS/PDC'?  
Usually theVPS or PDC time is the same than the start time. But  
if your TV guide shows aVPS or PDC time which is different from  
the programme’s scheduled start time, e.g. 20.10 (VPS/PDC  
20.14), you must enter theVPS/PDC time exact to the minute. If  
you want a start time different from theVPS/PDC time, you must  
switchVPS/PDC off.  
Programming a recording (without the  
SHOWVIEW® system)  
1
2
3
PressVCR, then DISC/VCR MENU.  
SELECT  
K
L
CHOOSE  
B
Select 'TIMER' with K/L.Then  
press B.  
Select ONCE, DAILY, or WEEKLY  
recording with K/L.Then press B.  
If all Timer blocks are in use,‘FULL’  
will appear on the OSD.  
¡ONCE  
DAILY  
WEEKLY  
TIMER LIST  
END=EXIT  
4
Select the desired Timer block with  
numerical key pads. (The flashing  
Programming a recording (with the  
'SHOWVIEW® system')  
number indicates an empty TIMER block.)  
R
Selecting once/daily/weekly recordings  
Using K/L, select from the following options:  
'ONCE': Recording once  
You no longer need to tediously enter the date, programme  
number, start and end time.All the information needed for pro-  
gramming is contained in the SHOWVIEW-programming number.  
You can find this SHOWVIEW number in most TV listing maga-  
zines written next to the concerned programme.  
'DAILY': Repeated daily recordings (Monday to Friday)  
'WEEKLY.': Repeated weekly recordings (every week on the same  
day)  
5
Enter the Start time (START) End time (STOP), Programme  
number (PROG.),VPS/PDC information and the Date with  
numerical key pads.  
1
2
Press SV/V+.  
ShowView system  
Enter the entire SHOWVIEW num-  
ber.This number is up to 9 digits  
long and can be found next to the  
start time of the TV programme in  
your TV listing magazine. [e.g: 1-  
234-5 or 1 234 5]  
If you make a mistake, you can  
clear your input with CLEAR.  
Press SV/V+.  
ShowView No.  
Programme numbers of the ' AV1 ' , ' AV2 ' and ' AV3'  
scart socket  
You can also programme recordings from external sources via  
scart socket AV1(TV),AV2 (DECODER) or AV3(FRONT).  
12345 – – – –  
SET=SV/V+  
CORRECT=CLEAR  
END=EXIT  
6
When all inputs are correct, press STATUS/EXIT.The program-  
ming information is stored in a TIMER block.  
Insert a cassette with an intact security tab (unprotected).  
Press TIMER SET.  
ShowView system  
7
8
3
4
¡ONCE  
DAILY  
WEEKLY  
Select ONCE, DAILY, or WEEKLY  
recording with K/L.Then press B.  
SELECT  
K
L
CHOOSE  
B
OTR (OneTouch Recording)  
END=EXIT  
This function enables you to set a recording length simply by  
pressing RECORD on the DVD/VCR.  
Follow steps 1 to 2 in “Recording without automatic switch-  
off” section.  
Press RECORD on the DVD/VCR repeatedly until the desired  
recording length appears.  
Selecting once/daily/weekly recordings  
Using K/L, select from the following options:  
'ONCE': Recording once  
1
2
'DAILY': Repeated daily recordings (Monday to Friday)  
'WEEKLY.': Repeated weekly recordings (every week on the same  
day)  
'- -' appears at PROG. .  
* The programme number of the TV channel has not yet been  
assigned to the SHOWVIEW number. Using the numerical key  
pads, select the corresponding programme number (name) of  
the TV channel.  
The following message appears on the screen:'ERROR'  
* The entered SHOWVIEW number is incorrect. Correct your input  
or end with STATUS/EXIT.  
* Check the time/date (see chapter 'Installing your video', section  
'Setting the time and date').  
* A daily recording was entered for the wrong day. Daily pro-  
gramming can only be used for recordings to be made from  
Monday to Friday.  
0:00  
0:30  
1:00....  
7:30  
8:00  
REC (Normal recording)  
• Recording stops when 0:00 is reached.  
To check time remaining during an OTR  
Press DISPLAY.  
To change the recording length during an OTR  
Press RECORD until the desired length appears.  
To stop an OTR before recording is finished  
Press STOP.  
To cancel the OTR but continue recording  
Press RECORD repeatedly until “REC” appears in the upper  
left corner of the TV screen.  
The following message appears on the screen:'TIMER  
NOT COMPLETED'  
* The channel is wrong.  
12  
 
Other Functions  
How to check, or delete a programmed  
recording (TIMER)  
Blue Background on or off  
If you want the TV screen to be solid blue when a weak signal  
is received, set BLUE BACKGROUND to ‘ON’.The screen will  
be blue and the sound will be muted. Or, if you want to receive  
the weak signal, set BLUE BACKGROUND to ‘OFF’.  
PressVCR, then DISC/VCR MENU.  
1
2
3
PressVCR, then DISC/VCR MENU.  
SELECT  
K
L
CHOOSE  
B
ONCE  
DAILY  
WEEKLY  
Press K/L to select 'TIMER'.Then  
press B.  
Press K/L to select 'TIMER LIST' ,  
then press B.  
1
¡TIMER LIST  
2
3
Press K/L to select 'VCR SET UP' , then press B.  
Press K/L to select 'BLUE BACK-  
4
5
Select timer block with B.  
To cancel the recording, press  
CLEAR.  
SELECT  
K
L
CHOOSE  
B
END=EXIT  
GROUND' , then press B.  
Select 'OFF' (no blue background)  
or 'ON' (blue background on) with  
B.  
STATUS DISPLAY [ON]  
BLUE BACKGROUND [ON]  
CLOCK DISPLAY  
4
¡
[ON]  
6
7
To end, press STATUS/EXIT.  
Press TIMER SET.  
5
To end, press STATUS/EXIT.  
END=EXIT  
How to change a programmed recording  
(TIMER)  
1
2
3
PressVCR, then DISC/VCR MENU.  
Press K/L to select 'TIMER' ,then press B.  
Press K/L to select ONCE, DAILY,  
Clock Display  
This function allows you to switch theVCR display off. It is  
useful in case you feel disturbed by the display-brightness while  
watching TV in a dark room. It also reduces the power con-  
sumption.  
ONCE  
or WEEKLY recording with K/L ,  
then press B.  
TIMER - 1 2 3 4 5 6 7 8 -  
4
5
Select a TIMER block with numeri-  
cal key pads. (The flashing number  
indicates an empty TIMER block.)  
1
2
3
4
5
PressVCR, then DISC/VCR MENU.  
SELECT  
K
L
CHOOSE  
B
Press K/L to select 'VCR SET UP'  
, then press B.  
Press K/L to select 'CLOCK DIS-  
PLAY' , then press B.  
Select 'OFF' (no clock display) or  
'ON' (clock display on) with B.  
To end, press STATUS/EXIT.  
Press CLEAR to delete information  
SELECT TIMER NUMBER  
STATUS DISPLAY [ON]  
BLUE BACKGROUND [ON]  
¡CLOCK DISPLAY  
and input correct information with END=EXIT  
numerical key pads.  
To end, press STATUS/EXIT.  
Press TIMER SET.  
[ON]  
6
7
END=EXIT  
Hint forTimer Recording  
• If there is a power failure or the DVD/VCR is unplugged for more than  
1 minute, the clock setting and all timer settings will be lost.  
• If a tape ends during TIMER RECORDING, the DVD/VCR will stop,  
eject the tape, and switch to the DVD mode automatically as the  
TIMER light blinks. (If the DVD power is off, the DVD/VCR will become  
the STANDBY status).  
• If a tape is not in the DVD/VCR or does not have a record tab, the  
TIMER light flashes and timer recording will not operate. Please insert a  
recordable tape.  
• When timer recordings are set, the TIMER light will come on.To use  
the DVD/VCR as usual until the time for the recording, press TIMER  
SET so that the TIMER light disappears. Press DVD/VCR to choose  
VCR or DVD modes, then continue with the other features as  
described in this manual.  
Selecting the sound channel  
You can select the desired sound channel during playback or  
while receiving TV channels via the DVD/VCR.This allows you  
to select a desired lan-  
•
During reception of bilingual broadcasts:  
guage for multi-language  
transmissions.  
Press AUDIO.This will  
show the current sound  
setting.  
Press AUDIO until the  
desired setting appears in  
the display.  
Display on  
the TV screen  
Mode  
MAIN  
SUB  
AUDIO OUTPUT  
1
2
L
Main Audio  
Main Audio  
Sub Audio  
Sub Audio  
Main Audio  
Sub Audio  
MAIN  
R
L
SUB  
R
L
'PRESS TIMER SET BUTTON FOR TIMER RECORDING' appears on  
the screen  
* Press TIMER SET on several minutes before the start of a pro-  
grammed recording.  
Error message: 'FULL'  
• If this error message appears after you select 'ONCE', 'DAILY', or 'WEEK-  
LY' on TIMER menu and press B, then all TIMER blocks are already pro-  
grammed. No more recordings can be programmed. If you want to clear or  
check a programmed recording (TIMER block),select the programme num-  
ber on TIMER LIST menu and press CLEAR.  
MAIN  
SUB  
MAIN  
SUB  
R
•
Reception of stereo broadcasts:  
Display on  
the TV screen  
Mode  
Stereo  
L
AUDIO OUTPUT  
L
L Audio  
STEREO  
LEFT  
R
L
R Audio  
L Audio  
R
L
R
L
L Audio  
R Audio  
R Audio  
L+R Audio  
L+R Audio  
R
RIGHT  
NONE  
Switching the status display off or on  
Monaural  
R
Along with the on screen menu, the status display also displays  
information on the current operating status (counter, playback,  
recording,TV channel, etc.) on the TV screen.You can switch  
off the information about the operating status so that the sta-  
tus display is not recorded when copying videocassettes.  
• During playback of the recorded tape in Hi-Fi mode:  
Display on  
the TV screen  
Mode  
Stereo  
L
AUDIO OUTPUT  
L
Hi Fi L Audio  
Hi Fi R Audio  
Hi Fi L Audio  
Hi Fi L Audio  
Hi Fi R Audio  
Hi Fi R Audio  
Normal Audio  
Normal Audio  
STEREO  
R
L
1
2
PressVCR, then DISC/VCR MENU.  
Press K/L to select 'VCR SET UP'  
, then press B.  
Press K/L to select 'STATUS DIS-  
PLAY' , then press B.  
LEFT  
RIGHT  
MONO  
SELECT  
K
L
CHOOSE  
B
R
L
R
L
¡STATUS DISPLAY [ON]  
R
BLUE BACKGROUND [ON]  
3
4
5
CLOCK DISPLAY  
[ON]  
Monaural  
R
Press K/L to select 'ON' or 'OFF'  
, then press B.  
To end, press STATUS/EXIT.  
Hi Fi L Audio  
L
+
Normal Audio  
MIX  
MIXED  
END=EXIT  
Hi Fi R Audio  
R
+
Normal Audio  
Which settings can I choose?  
'ON': Shows the status display for a few seconds only.  
'OFF': Switches off the status display.  
13  
 
Playing a Disc  
DVD-V  
CD  
VCD  
DVD-V  
Basic Playback  
Title Menu  
1
2
3
Press DVD, then TITLE.  
•The title menu will appear.  
If the feature is not available,  
TV screen.  
Press Arrow ( L / K / B / s ) to select an item, and OK to  
confirm selection.  
Getting Started  
Turn on the power of the TV, amplifier and any other compo-  
nents which are connected to the DVD/VCR.  
Make sure the TV and audio receiver (commercially available)  
are set to the correct channel.  
symbol may appear on the  
1
2
3
Press STANDBY-ON.  
• Playback will begin at the selected Title.  
Press DVD, then OPEN/CLOSE to open disc loading tray.  
Place the chosen disc in the tray, with the  
label facing up.  
Press PLAY B.  
•The tray will close automatically, and  
playback will then start from the first  
chapter or track of the disc. If the play-  
back does not start automatically, press  
PLAY B.  
•When you playback the DVD which a title menu is recorded,  
it may appear on the screen. In this case, refer to “TITLE  
MENU”.  
VCD  
1
2
The title menu will appear.  
Press numerical key pads to select the menu.  
• Playback will start.  
4
DVD-V  
Calling Up a Menu During Playback  
• Press DISC/VCR MENU to call up the DVD main menu.  
• Press TITLE to call up the title menu.  
5
Press STOP C to stop playback.  
Note:  
Notes:  
- Contents of menus and corresponding menu operations  
may vary between discs. Refer to the manual accompa-  
nying the disc for details.  
- A “prohibited icon” may appear at the top-right on the  
TV screen during operation, warning that  
a prohibited operation has been encoun-  
tered by the DVD/VCR or the disc.  
- With DVDs that use some titles for play-  
back program signals, playback may start  
from the second title, or it may skip these titles.  
- During the playback of two layered disc, pictures may  
stop for a moment.This happens when the 1st layer  
switches to the 2nd layer.This is not a malfunction.  
VCD  
DVD-V  
Step by Step Playback  
During playback, press PAUSE k.  
1
2
3
• Playback will pause and sound will be muted.  
The disc goes forward by one frame each time PAUSE is  
pressed.  
To exit step by step playback, press PLAY B.  
General Features  
CD  
VCD  
DVD-V  
Resume  
DVD or video CDs may contain menus to navigate the disc  
and access special features. Press the appropriate numerical key  
pads or use Arrow ( L / K / B / s ) to highlight your selection  
in the DVD main menu and press OK to confirm.  
1
2
During playback, press STOP C.  
• Resume message will appear on the TV screen.  
Press PLAY B, playback will resume from the point at which  
playback was stopped.  
Note:  
•To cancel resume, press STOP C twice.  
- Unless stated, all operations described are based on  
remote control use. Some operations can be carried out  
using the menu bar on theTV screen.  
Note:  
- If you turn the DVD/VCR off, Resume function will be  
cancelled.  
- Some Video CDs with PBC function resume playback  
from the beginning of the track.  
CD  
VCD  
DVD-V  
Pause  
1
2
During playback, press PAUSE k.  
• Playback will pause and sound will be muted.  
To continue playback, press PLAY B.  
Fast Forward / Reverse Search  
CD  
MP3  
VCD  
DVD-V  
1
2
During playback, press FWDg or REVh repeatedly to select  
the required forward or reverse speed: x2, x8, x50, x100.  
• For video CDs, the speed is fixed at x2, x8, x30.  
• For audio CDs, the speed is fixed at x16.  
• For MP3, the speed is fixed at x8.  
To return to normal playback, press PLAY B.  
DVD-V  
Disc Menus  
1
2
3
Press DVD, then DISC/VCR MENU.  
•The DVD main menu will appear.  
If the feature is not available,  
TV screen.  
If disc menu is available on the disc, audio language, subtitle  
options, chapters for the title and other options will appear for  
selection.  
symbol may appear on the  
4
Press Arrow ( L / K / B / s ) to select an item, and OK to  
confirm selection.  
VCD  
DVD-V  
Slow Forward / Slow Reverse  
During playback, press PAUSE k.  
Press g or h .  
1
2
•
Slow motion playback will begin and sound will be muted.  
3
4
Press g or h repeatedly to select the required speed:  
1/16, 1/8, 1/2 of the normal playback.  
To return to normal playback, press PLAY B.  
Note:  
- Slow Reverse is not available on video CDs.  
14  
 
Playing a Disc  
VCD  
DVD-V  
Zoom  
Repeat  
e Zoom function allows you to enlarge the video image and to  
pan through the enlarged image.  
• REPEAT are available only during playback.  
1
2
3
4
Press ZOOM during playback.  
• Playback will continue.  
Press ZOOM repeatedly to select the required zoom factor:  
x2, x4 or OFF.  
Use Arrow ( L / K / B / s )to move the zoomed picture  
across the screen.  
DVD-V  
RepeatTitle / Chapter  
To activate the repeat function, press REPEAT during playback.  
•The repeat mode changes as described below every time you  
press the button.  
OFF  
(repeat off)  
CHAPTER  
(current chapter repeat)  
TITLE  
(current title repeat)  
To exit zoom mode, press ZOOM to OFF.  
Notes:  
- Zooming function does not work while disc menu is  
shown.  
- x4 zoom is not available on some discs.  
- only x2 zoom is available on video CDs.  
Notes:  
- RepeatTitle/Chapter is not available with some scenes.  
-The REPEAT setting will be cleared when moving to  
other title or chapter.  
CD  
VCD  
RepeatTrack  
(without PBC function)  
VCD  
CD  
(without PBC function)  
Track  
To activate the repeat function, press REPEAT during playback.  
•The repeat mode changes as described below every time you  
press the button.  
re are three ways to begin playback on an Audio CD at a spe-  
Track.  
Using the Numerical key pads  
OFF  
(repeat off)  
TRACK  
(current track repeat)  
ALL  
(entire disc repeat)  
1
Press numerical key pads to enter the desired Track number.  
• Playback will start at the selected track.  
• For single digit tracks (1-9), press a single number (eg. track 3,  
press 3).  
MP3  
•
To play track 26, press +10, 2, 6 on the numerical button.  
GROUP  
(entire group  
repeat)  
OFF  
(repeat off)  
TRACK  
(current track  
repeat)  
ALL  
(entire disc  
repeat)  
Using the SEARCH MODE  
Press SEARCH MODE.  
• The track search display appears.  
Within 30 seconds, select a desired track number using  
numerical key pads. For single digits press “0” first.  
• Playback will start at the selected track.  
1
2
Notes:  
-The REPEAT setting will be cleared when moving to  
other track.  
- Repeat playback does not function during repeat A-B  
playback.  
- Repeat playback is not available when you play the  
Video CD with PBC function.  
Using the SKIP  
ring playback, press  
H
G
G
to move to the next track. Press it  
to go back to  
SKIP  
repeatedly to skip subsequent tracks. Press  
H
SKIP  
the beginning of the current track. Press it repeatedly to go to the  
previous tracks  
Track number will appear briefly on the DVD display panel.  
.
•
• If SKIP is pressed while the playback is paused, the playback  
will be paused again after skipping to the next track.  
Note:  
CD  
VCD  
Repeat at A-B  
Press REPEAT A-B at your chosen starting point.  
A- appears briefly on the TV screen.  
Press REPEAT A-B again at your chosen end point.  
1
2
• SKIP  
H
G are not available when playback is  
•
stopped.  
•
A-B appears briefly on the TV screen, and the repeat  
sequence begins.  
DVD-V  
Title / Chapter Search  
3
To exit the sequence, press REPEAT A-B.  
Notes:  
1
2
Press SEARCH MODE once for  
the Chapter search, twice for the  
Title search during playback.  
Enter the desired chapter/title  
number using numerical key pads.  
-The repeat A-B section can only be set within the cur-  
rent title (for DVDs), or current track (for audio CDs).  
- Repeat A-B is not available with some scenes in DVD.  
-To cancel the A point which was set, press CLEAR.  
- Repeat A-B playback does not function during title,  
chapter, track or all repeat playback.  
/2  
VCD  
DVD-V  
CD  
(without PBC function)  
Time Search  
1
2
During playback, press SEARCH MODE three times  
(CD/VCD: twice) to display the Time Search on the TV screen.  
Within 30 seconds, enter a desired disc time using numerical  
key pads.  
• Playback will start at the specified time.  
Press CLEAR to erase the incorrect input.  
3
15  
 
Playing a Disc  
CD  
MP3  
Program  
On-Screen Information  
You may determine the order in which tracks will play.  
You can check the MP3 files during playback.  
Press DISPLAY.  
•The name of the file currently in play will be displayed.  
Press DISPLAY again to show the track number, the elapsed  
time, the repeat status, and the playback status at the top of  
the screen.  
1
2
In stop mode press MODE.  
•The PROGRAM screen will appear.  
Press L or M to select a track,  
then press OK.  
• Press CLEAR to erase the The  
most recently entered pro-  
gram.  
1
2
TOTAL  
T
T
•
will be displayed when the repeat play has been selected.  
T - indicates Track repeat  
T
T
T
T
T
T
3
Press PLAY B to play the pro-  
grammed tracks.  
G- indicates Group (folder) repeat  
A - indicates Disc repeat  
OK  
T
Notes:  
3
Press DISPLAY again to exit.  
- While the program is being  
played back, the STOP C works as follows.  
- Press STOP C once and then PLAY again, playback will  
restart from the point where STOP C was pressed.  
MP3  
Track Selection  
B
1
2
Press SEARCH MODE during playback.  
•The FILE LIST will appear.  
Select a desired track using Arrow (L/K/B/s)  
• Press B when you want to go to the next hierarchy.  
• Press s when you want to go back to the previous hierarchy.  
Press PLAY B to start playing  
(Program continued)  
- Press STOP C twice and then PLAY  
B
again, playback will  
.
restart from the track in the usual way. (Program cleared)  
- Up to 99 programs can be entered.  
- If you like to repeat the current track in the program, press  
3
REPEAT repeatedly until  
TRACK appears during play-  
Notes:  
back. If you like to repeat the entire program press  
- Press SEARCH MODE to EXIT.  
- Some selections may take a while to be recognized.  
REPEAT repeatedly until  
ALL appears during playback.  
CD  
Random Playback  
MP3  
Random Playback  
This shuffles the playing order  
of tracks instead of playback in  
the sequence.  
In stop mode, press MODE  
twice.  
1
2
Press MODE twice while playback is stopped.  
Press PLAY B to play the tracks in random order.  
RANDOM  
CD [AUDIO]  
TOTAL 0:45:55  
1
2
RANDOM PROGRAM  
-- no indication --  
MP3  
•
RANDOM screen appears  
.
Program  
Press PLAY B to start ran-  
dom playback.  
PLAY  
This feature allows you to program a mp3 disc to play in a  
desired sequence.  
Press MODE during playback is stopped.  
•The PROGRAM screen will appear.  
Press K or L to select a track, then press OK, to save it in a  
program.  
Notes:  
1
2
- If you like to repeat the current track in the random  
selection, press REPEAT repeatedly until TRACK  
appears during playback. If you like to repeat the entire  
random selection press REPEAT repeatedly until  
appears during playback.  
ALL  
• Press CLEAR to erase the incorrect input.  
Press PLAY B to start programmed playback.  
3
MP3  
MP3/JPEG Playback  
VCD  
DVD-V  
Audio Language  
When a CD with MP3 or JPEG files is inserted in the  
DVD/VCR, the MP3 or JPEG menu will appear on the TV  
screen, and number of tracks is displayed on the front panel.  
In stop mode, press K or L to  
The DVD/VCR allows you to select a language during DVD  
disc (if multi language available) playback.  
Press AUDIO during playback.  
Press AUDIO repeatedly to select your desired language.  
Notes:  
- Pressing AUDIO may not work on some DVDs with multiple  
audio languages (e.g. DVDs which allow audio language  
setting on the disc menu).  
- Some discs allow audio language setting on the disc menu.  
(Operation varies between discs, so refer to the manual  
accompanying the disc.)  
1
2
1
select the desired group, MP3  
track or JPEG file.  
• If a group is selected, press  
PLAY B or OK to go on to  
the track selection screen.  
Press K or L to choose a  
track, then press PLAY B or  
OK.  
FOLDER  
MP3  
JPEG  
OK  
PLAY  
• If a track is selected, press PLAY B or OK to start playing  
tracks. Starting from the one you’ve just chosen the subse-  
quent tracks will be played.  
• Choose FIRST PLAY to start playback from the beginning of  
the listed tracks.  
• Press TITLE to return to the first item.  
Press STOP C to stop playback.  
Notes:  
CD  
VCD  
Stereo Sound Mode  
1
Press AUDIO repeatedly during playback to select between  
STEREO, L-CH or R-CH.  
STEREO - both right and left channels are active (stereo)  
L-CH - only left channel is active  
2
R-CH - only right channel is active  
- Folders are known as Groups; files are known asTracks.  
Note:  
3
- MP3 files are accompanied by  
- JPEG files are accompanied by  
icon.  
icon.  
- If the Virtual Surround setting is ON, the sound mode  
will be fixed to STEREO, and can not be changed.  
- Maximum of 255 folders can be recognized.  
- Maximum of 256 files can be recognized.  
- Up to 8 hierarchies can be created.  
This player recommends the use of files recorded at the below  
specifications:  
• Sampling frequency: 44.1kHz or 48kHz  
• Constant bit rate: 112kbps ~ 320kbps.  
16  
 
Playing a Disc  
DVD-V  
DVD-V  
Subtitle Language  
Parental Control  
The DVD/VCR allows you to select a language for subtitle dur-  
ing DVD disc (if available) playback.  
Press DVD, then SUBTITLE during playback.  
Press SUBTITLE repeatedly to select your desired subtitle lan-  
guage.  
•The selected language will be displayed on the display bar at  
the top of the screen.  
To turn off subtitles, press SUBTITLE repeatedly until OFF  
appears.  
Parental Control limits the disc viewing that exceed your set-  
tings. (with a password or playback will stop.)  
This feature allows you to prevent discs with alternative scenes  
from being played by your children.  
1
2
Parental Level  
Parental Level allows you to set the rating level of your DVD  
discs. Playback will stop if the disc’s ratings exceed the level  
you set.  
Press SYSTEM MENU in STOP mode.  
Press B to select CUSTOM, then press OK.  
Press s or B to select PARENTAL, then press OK.  
Enter your four-digit password then press OK.  
Press K or L to select PARENTAL  
LEVEL, then press OK.  
3
1
2
3
4
5
Notes:  
- Some discs allow subtitle language setting on the disc  
menu. (Operation varies between discs, so refer to the  
manual accompanying the disc.)  
- If the desired language is not shown after pressing SUBTI-  
TLE several times, the disc does not have subtitles in that  
language.  
- If you choose a Language that has a 3 letter language  
code, the code will be displayed every time you change the  
Subtitle language setting. If you choose any other lan-  
guages,‘---’ will be displayed instead. (Refer to back inside-  
cover.)  
6
7
Press K or L to select the desired  
level, then press OK.  
PARENTAL  
PARENTAL LEVEL ALL  
Press SYSTEM MENU to exit.  
Notes:  
- When doing this for the first time, enter any 4 digits.  
(except for 4737)That number will be used as the pass-  
word from the second time onward.  
-To change the password, press K or L to select CHANGE,  
then press OK. Enter the four-digit pass-word, then press  
OK.  
- With some DVDs, it may be difficult to find if they are com-  
patible with parental lock. Be sure to check if the parental  
lock function operates in the way that you have set.  
- Record the password in case you forget it.  
DVD-V  
Camera Angle  
Some DVD discs contain scenes which have been shot simulta-  
neously from various angles.You can change the camera angle  
when the (  
) icon appears on the screen.  
IfYou Forget the Password  
Press 4, 7, 3, 7 at step 4.  
• Password will be cleared and parental level will be set to ALL.  
Proceed the above steps 4-5 again.  
1
2
Press DVD, then ANGLE during playback.  
•The selected angle will be displayed on the display bar at the  
top of the screen.  
1
2
Press ANGLE repeatedly to select your desired angle.  
Control Levels  
ALL  
All parental lock is cancelled.  
Level 8  
DVD software of any grade (adult/general/children) can be  
Changing the On-Screen Display  
DVD-V  
played back.  
Levels 7 to 2  
You can check information about the current  
disc by pressing DISPLAY on the remote  
control.  
Press DISPLAY during playback to show current Chapter.  
a The elapsed and remaining playing time of the current chap-  
ter will be displayed.  
Only DVD software intended for general use and children can  
be played back.  
Level 1  
Only DVD software intended for children can be played back,  
with those intended for adult and general use prohibited.  
1
2
3
Press DISPLAY again to show current Title.  
a The elapsed and remaining playing time of the current title  
will be displayed.  
Press DISPLAY the third time.  
a The BIT RATE, layer number (if available) and the current  
repeat setting will be displayed.  
VCD  
CD  
Marker Setup Screen  
DVD-V  
(without PBC function)  
e markers to memorise your favourite places on a disc.  
1
Press SEARCH MODE four times (CD: three times) during play-  
back.  
The display screen and Markers will appear on the TV screen.  
Press s or B to select 1, 2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that  
“-- -- : --” appears in the display.  
When reaches the desired point, press OK.  
•The Title or Track and elapsed playing time will appear in the  
TV screen.  
•
4
1
Press DISPLAY the fourth time to remove the display.  
2
3
VCD  
CD  
(without PBC function)  
Press DISPLAY during playback, the current Track will be dis-  
played on the TV screen.  
4
To return to the Marker later, press SEARCH MODE four times  
(CD/VCD: three times) during playback and s or B to choose  
the desired marker, then press OK.  
a The elapsed and remaining playing time of the current total  
track will be displayed.  
Press DISPLAY again to show current Total Track.  
a The elapsed and remaining playing time of the current total  
track will be displayed.  
2
3
es:  
-
-
-
Opening the disc tray or turning off the power or select  
AC at step 2 and press OK will erase all Markers.  
To clear a marker, using s or B, position the cursor on  
to the marker number to be cleared and press CLEAR.  
You can mark up to 10 points.  
Press DISPLAY the third time to remove the display.  
5
Press SEARCH MODE or RETURN to exit.  
17  
 
DVD Setup  
5
6
Press K or L to select a setting, then press OK.  
• If OTHER is selected in the AUDIO, SUBTITLE or DISC  
MENU screen, press four-digit number to enter the code for  
the desired language. (Refer to the language code list on back  
inside cover).  
• Only the languages supported by the disc can be selected.  
Press SYSTEM MENU to exit.  
Audio Setting  
Choose the appropriate Audio settings for your equipment as it  
only affect during the playback of DVD discs of the DVD/VCR.  
Press SYSTEM MENU in STOP mode.  
Press B to select CUSTOM, then press OK.  
CUSTOM mode will appear.  
Press s or B to select AUDIO, then OK to confirm.  
Press K or L to select the below items, then press OK.  
DRC (Dynamic Range Control) :  
To compress the range of sound volume.  
The default setting is OFF.  
1
2
3
4
Note:  
- Language Setting for Audio and Subtitle is not available  
with some discs.Then use AUDIO and SUBTITLE. Details  
are on pages 16-17.  
Dolby Digital :  
Set to ON when the player is connect-  
ed to Dolby Digital Decoder.  
(ON : Output by Dolby Digital)  
(OFF : Convert the Dolby Digital to PCM)  
The default setting is ON.  
DOWN SAMPLING :  
Set to ON when outputting in 48kHz.  
The default setting is ON.  
QUICK  
DVD-V  
AUDIO  
Display Setting  
DRC  
OFF  
ON  
DOLBY DIGITAL  
DOWN SAMPLING ON  
MPEG  
OFF  
markers to memorise your favourite places on a disc.  
2
Press SYSTEM MENU in STOP mode.  
Press B to select CUSTOM, then press OK.  
• CUSTOM mode will appear.  
Press s or B to select DISPLAY, then OK to confirm.  
Press K or L to select the below items, then press OK.  
3
4
TV Aspect :  
QUICK  
When playing disc with copyright Protection  
Press K or L for an item selection,  
• If you select OFF, copyright protection will be activated and  
sound will be down sampled at 48kHz.  
MPEG :  
Set to ON when the player is connected MPEG Decoder.  
(ON: Output by MPEG)  
then press OK.  
DISPLAY  
TV ASPECT  
4:3 LETTER BOX  
ON  
Select 4:3 LETTER BOX for a black  
bars appears on top and bottom of  
the screen.  
ANGLE ICON  
AUTO POWER OFF ON  
Select 4:3 PAN & SCAN for a full height picture with both sides  
trimmed.  
Select 16:9 WIDE if a wide-screen TV is connected to the  
DVD/VCR.  
(OFF: Convert the MPEG to PCM)  
• The default setting is OFF.  
Press SYSTEM MENU to exit.  
5
The default setting is 4:3 LETTER BOX.  
Angle Icon :  
Press OK repeatedly to turn Angle icon ON or OFF.  
The default setting is ON.  
VCD  
CD  
MP3  
Virtual Surround  
DVD-V  
You can enjoy stereophonic visual space on your existing stereo  
system.  
1
2
Press MODE during playback.  
Auto Power Off :  
Press OK to set it 1(Natural effect),  
Press OK repeatedly to turn Auto Power off ON or OFF.  
The default setting is ON and it will turn the DVD/VCR to off  
automatically after 35 minutes of no use.  
Press SYSTEM MENU to exit.  
2(Emphasized effect) or OFF.  
Press MODE or RETURN to exit.  
Note (for CD play only):  
OFF  
3
5
Notes:  
-
Virtual Surround will not be effective if the sound mode  
is set to something other than STEREO.  
- Be sure to press SYSTEM MENU, or the setting will not  
work.  
- You can also choose the item by pressing the numbers.  
DVD-V  
Language Setting  
uage options are not available with some discs.  
2
Press SYSTEM MENU in STOP mode.  
Press B to select CUSTOM, then press OK.  
• CUSTOM mode will appear.  
3
4
Press s or B to select LANGUAGE, then OK to confirm.  
Press K or L to select the below items, then press OK.  
AUDIO :  
Sets the audio language.  
SUBTITLE :  
Sets the subtitle language.  
DISC MENU :  
Sets the language for DVD Menu.  
PLAYER MENU :  
Sets the language for the On-Screen display.  
QUICK  
Maintenance  
Cleaning the Cabinet  
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abra-  
sives.  
Cleaning Discs  
• When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the centre out. Do not wipe in a circular motion.  
• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue records.  
Cleaning the disc lens  
• After prolonged use, dirt or dust may accumulate at the disc lens.To ensure good playback quality, clean the disc lens with Philips CD  
Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner.  
18  
 
Specificatis  
PLAYBACK SYSTEM  
DVD  
fs 96 kHz  
fs 48 kHz  
fs 44.1 kHz  
20 Hz - 44 kHz  
20 Hz - 22 kHz  
20 Hz - 20 kHz  
70 dB  
DVDVideo,Audio CD, DVD+RW, DVD-R/RW,  
DVD+R, CD-R/RW,VIDEO CD  
CD  
Signal-Noise (1kHz)  
Dynamic Range (1kHz)  
Distortion and Noise (1kHz)  
TV STANDARD (PAL/50Hz) (NTSC/60Hz)  
70 dB  
0.1%  
Number of lines  
Playback  
625  
Multistandard  
525  
(PAL/NTSC)  
CONNECTIONS  
VIDEO PERFORMANCE  
SCART  
2x Euroconnector  
S-Video OutputMini DIN, 4 pins  
Audio L+R output  
Digital Output 1 coaxial, 1 optical  
Video output  
RGB (SCART) output  
Video Shift  
1Vpp into 75 ohm  
0.7Vpp into 75 ohm  
Left/Right  
2x Cinch (white/red)  
IEC958 for CDDA / LPCM  
IEC1937 for MPEG1/2, Dolby  
Digital  
VIDEO CASSETTE RECORDER  
Video heads  
Antenna  
VHF output  
Four heads Hi-Fi  
VHF/UHF - 75 ohm  
75 ohm unbalanced  
CABINET  
Dimensions (w x h x d)  
Weight  
435 x 99 x 218 mm  
Approximately 3.8 Kg  
AUDIO FORMAT  
Digital  
MPEG  
Compressed  
Digital  
16, 20, 24 bits  
fs, 44.1, 48, 96 kHz  
POWER SUPPLY (UNIVERSAL)  
Power inlet  
Power usage  
Power usage standby  
220 ~ 240V , 50 Hz  
Approx. 30 W  
9.2 W  
(standby : 5.0 W)  
(When CLOCK DISPLAY set to OFF.)  
Dolby Digital  
PCM  
Analogue Stereo Sound  
Dolby Surround-compatible downmix from Dolby Digital multi-channel  
sound  
Specifications subject to change without prior notice  
3D Sound for virtual 5.1 channel sound on 2 speakers  
AUDIO PERFORMANCE  
DA Converter 24 bits  
Troubleshootg  
Problem  
Solution  
No power  
No picture  
–
–
–
–
–
–
Check if the AC power cord is properly connected.  
Check if the TV is switched on.  
Check the video connection.  
Sometimes a small amount of picture distortion may appear.This is not a malfunction.  
Connect DVD/VCR directly to the TV.  
Make sure the disc is compatible with the DVD/VCR.  
Distorted picture  
Completely distorted picture or  
black/white picture with DVD  
No sound or distorted sound  
– Adjust the volume.  
– Check that the speakers are connected correctly.  
– Check the digital connections.  
No audio at digital output  
– Check if the audio format of the selected audio  
language matches your receiver capabilities.  
No DTS audio at analog output  
No sound and picture  
– Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.  
– Check that the SCART cable is connected to the correct device (See Connecting to a TV)  
Picture freezes momentarily during  
playback  
– Check the disc for fingerprints/scratches and clean with a soft cloth wiping from centre  
edge.  
– This may happen when you use the disc recorded in the non-seamless manner.This is not a  
malfunction.  
Disc can’t be played  
– Ensure the disc label is facing up.  
– Check if the disc is defective by trying another disc.  
– Reset the unit by switching the DVD/VCR off, then on again.  
No return to start-up screen when disc is  
removed  
The DVD/VCR does not respond to the  
remote control  
– Aim the remote control directly at the sensor on the front of the DVD/VCR.  
– Reduce the distance to the DVD/VCR.  
– Replace the batteries in the remote control.  
– Re-insert the batteries with their polarities (+/– signs) as indicated.  
Buttons do not work or DVD/VCR stops  
responding  
– To completely reset the DVD/VCR, unplug the AC cord from the AC outlet for 5-10 sec-  
onds.  
DVD/VCR does not respond to some operating  
commands during playback.  
– Operations may not be permitted by the disc.  
Refer to the instructions of the disc.  
DVD/VCR cannot read CDs/DVDs  
– Use a commonly available cleaning CD/DVD to clean the lens before sending the DVD/VCR  
for repair.  
The DVD/VCR switches from DVD mode to  
VCR mode after 35 minutes  
–
Playback will stop for more than 35 minutes and no button is pressed.  
TheVCR do not record aTV program  
–
–
–
–
–
–
–
Make sure the tape has a record tab.  
Make sure the DVD/VCR is inVCR position.  
Check the TV and the DVD/VCR channel are similar.  
Make sure the recording start and stop times are set correctly.  
Make sure the tape has a record tab.  
Make sure the clock is set.  
The DVD/VCR may not perform or continue a timer recording if the power fails for more  
than 1 minute.  
The DVD/VCR do not perform a timer  
The motor (cylinder) rotates even when tape  
playback is stopped  
–
To enable quick play mechanism, the cylinder will rotate for about five minutes.This is nor-  
mal.  
You cannot insert a tape  
–
–
–
–
Insert a tape, window side up with the record tab facing you.  
Gently push on the center of the tape when putting into the DVD/VCR.  
Make sure the power plug is completely connected to a power outlet.  
Make sure the tape has a record tab.  
You cannot remove a tape  
DVD/VCR ejects the tape when you press  
RECORD orTIMER SET for a timer recording.  
If you are unable to remedy a problem by following these hints, consult your dealer or service centre (HOTLINE).  
19  
 
Language  
Code Language  
Code Language  
Code Language  
Code  
A-B  
French [FRE]  
Frisian  
Galician  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
Gujarati  
Hausa  
5264  
5271  
5358  
5747  
5051  
5158  
5758  
5360  
5367  
5447  
5569  
5455  
5467  
Macedonian  
Malagasy  
Malay  
Malayalam  
Maltese  
Maori  
Marathi  
Moldavian  
Mongolian  
Nauru  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
Siswat  
Slovak  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
4748  
4747  
4752  
6563  
4759  
4764  
5471  
4765  
4771  
4772  
4847  
5167  
4860  
5072  
4854  
4855  
4864  
4853  
5971  
4851  
Slovenian  
Somali  
Spanish [SPA]  
Sundanese  
Swahili  
Swedish [SWE]  
T
Tagalog  
Tajik  
Tamil  
Tatar  
Telugu  
Thai  
Tibetan  
Tigrinya  
Tonga  
Tsonga  
Turkish [TUR]  
Turkmen  
Twi  
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
Hebrew  
Hindi  
Nepali  
Norwegian [NOR] 6061  
Basque  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
O-R  
Bengali;Bangla  
Bhutani  
Occitan  
Oriya  
Oromo(Afan)  
Panjabi  
Pashto;Pushto  
Persian  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
5565  
5560  
5547  
5551  
5557  
5347  
5566  
5647  
5669  
5760  
5765  
5757  
6469  
5771  
6460  
5761  
5767  
Bihari  
Bislama  
Breton  
Bulgarian  
Burmese  
Byelorussian  
Polish  
Portuguese [POR] 6266  
C-E  
Quechua  
Rhaeto-Romance  
Romanian [RUM]  
Russian [RUS]  
S
Samoan  
Sangho  
Sanskrit  
Scots Gaelic  
Serbian  
Serbo-Croatian  
Sesotho  
Setswana  
Shona  
6367  
6459  
6461  
6467  
Cambodian  
Catalan  
5759  
4947  
7254  
4961  
5464  
4965  
5047  
6058  
5160  
5161  
5166  
U-Z  
Ukrainian  
Urdu  
Uzbek  
Vietnamese  
Volapuk  
Welsh  
Wolof  
Xhosa  
Yiddish  
Yoruba  
Zulu  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
Chinese [CHI]  
Corsican  
Croatian  
Czech  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
Korean [KOR]  
Kurdish  
L-N  
Laothian  
5861  
5847  
5868  
5860  
5866  
F-H  
Latin  
Latvian;Lettish  
Lingala  
Faroese  
Fiji  
5261  
5256  
5255  
Sindhi  
Singhalese  
Finnish [FIN]  
Lithuanian  
 
PHILIPS NORGE AS  
Sandstuveien 70,  
PO Box 1, Manglerud  
N-0612 Oslo  
PHILIPS  
Österreichische Philips Industrie  
GmbH  
Triesterstrasse 64  
1101 Wien  
PHILIPS PORTUGUESA, S.A.  
Consumer Information Center  
Rua Dr.António Loureiro Borge, nr.5  
Arquiparque, Miraflores  
P-2795 L-A-VEHLA  
NORWAY  
Phone: 2274 8250  
AUSTRIA  
PORTUGAL  
Tel: 0810 001 203  
Phone: 021-4163063  
OY PHILIPS AB  
Sinikalliontie 3,  
02630 Espo  
PHILIPS INFO CENTER  
Alexanderstrasse 1  
20099 Hamburg  
PHILIPS CE,The Philips Centre,  
420 - 430 London Road,  
Croydon, Surrey  
Helsinki  
FINLAND  
GERMANY  
CR9 3QR  
puh. 09 615 80 250  
Tel: 0180-53 56 767  
UNITED KINGDOM  
Phone: 0208-665-6350  
PHILIPS KUNDTJÄNST  
Kollbygatan 7,  
Akalla,  
16485 Stockholm  
SWEDEN  
SERVICE CONSOMMATEURS  
PHILIPS  
BP 0101  
75622 Paris Cédex 13  
FRANCE  
CONSUMER SERVICES  
Prags Boulevard 80. PO Box 1919,  
DK-2300 Copenhagen S  
DANMARK  
Phone: 08-598 52 250  
Phone: 0825-889 789  
TIf: 32 88 32 00  
PHILIPS POLSKA  
AL. Jerozolimskie 195B  
02-222 Warszawa  
POLSKA  
PHILIPS ELECTRONICS  
IRELAND LIMITED  
Consumer Information Center  
Newstead, Clonskeagh  
DUBLIN 14  
PHILIPS REPRESENTATION  
OFFICE  
Ul. Usacheva 35a  
119048 MOSCOW  
RUSSIA  
Tel.: (022)-571-0-571  
Phone: 01-7640292  
Phone: 095-937 9300  
PHILIPS SERVICE  
V Mezihori 2  
180 00 Prage  
CZECH REPUBLIC  
Phone: (02)-3309 9240  
PHILIPS CONSUMER  
ELECTRONICS  
Servizio Consumatori  
Via Casati 23  
PHILIPS INFO CENTER  
Fegistrasse 5  
8957 Spreitenbach  
SUISSE  
20052 Monza - Milano  
ITALY  
Phone: 800 820026  
Tel.: 0844-800 544  
PHILIPS Iberia, S.A.  
C/MartinezVillergas, 49  
28027 MADRID  
PHILIPS CUSTOMER CARE  
CENTER  
SPAIN  
Phone: 902-11 33 84  
PHILIPS MÁRKASZERVIZ  
Kinizsi U 30 - 36  
Budapest 1092  
HUNGARY  
Phone: (01)-2164428  
Twee Stationsstraat 80/  
80 Rue des Deux Gares  
1070 BURSSEL/BRUXELLES  
BELGIUM (for BENELUX)  
Tel: 070-222303  
Meet Philips at the Internet  
http://www.philips.com  
The products and services described herein are not necessarily  
available in all countries  
Due to continuous product improvements this document is  
subject to change without notice.  
Printed in China  
0VMN03761 / H9520ED*****  
 

Pelco Security Camera SD4N B0 X User Manual
Philco DVD Player PVD2000 User Manual
Philips Gas Grill 4000AZ User Manual
Philips Marine Instruments 19PFL5404 60 User Manual
Philips TV Antenna 37PF9731 69 User Manual
Philips TV Mount SYE5600 00 User Manual
Philips TV VCR Combo CCZ256AT User Manual
Pioneer Speaker XPRS12 User Manual
ProForm Home Gym PFMC77754 User Manual
ProForm Treadmill 831296230 User Manual