Rwegwistewr yo.upr hproildiupctsan.dcgoetmsup/pworteatlcome
CMQ205
EN
ES
User manual
3
13
25
Manual del usuario
PT-BR Manual do Usuário
RU
ZH-CNꢀ Ⴌ
߀ ൱Ҭꢀ Руководство пользователя 37
49
1 Important
Notice
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
Safety
•
Read and understand all instructions
before you use the apparatus. If damage
is caused by failure to follow instructions,
the warranty does not apply.
•
•
•
This unit is designed for negative ground
(earth) 12 V DC operation only.
Use only the supplied mounting hardware
for a safe and secure installation.
Do not connect any active speakers (with
built-in amplifier) to the speaker terminals
of the unit. Doing so may damage the
active speakers.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
•
•
To ensure safe driving, adjust the volume
to a safe and comfortable level.
To avoid short circuit, do not expose the
apparatus, remote control or remote
control batteries to rain or water.
Never expose the apparatus to direct
sunlight, naked flames or heat.
Clean the apparatus with soft, damp
cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the apparatus.
2010 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specifications are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
•
•
4
EN
2 Your car power
amplifier
Overview of the main unit
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
(
)
30A
Introduction
With the amplifier, you can enjoy high quality
sound performance with powerful bass and
beats.
a INPUT L/R
Connect car audio with RCA cable.
•
What’s in the box
Check and identify the contents of your
package:
b OUTPUT L/R
To connect additional amplifier with
RCA cable for additional speakers.
•
c INPUT LEVEL
•
Adjust input level (0.3V to 6V).
d FILTER MODE
•
Set frequency filter at LPF (low-pass-
filter), HPF (high-pass-filter), or OFF
(flat) mode.
e LPF FREQUENCY
Set LPF (low-pass-filter) frequency
from 80Hz to 120Hz.
•
a Amplifier
f BASS BOOST
Boost frequency for around 50Hz,
12dB.
b Screw (25mm) x 4
c Fuse x 1
•
g POWER/PROTECTED
•
Light in green when the amplifier is
switched on.
•
Light in red when the amplifier is
abnormal and protected.
h SPEAKER OUTPUT
Connect to speakers or subwoofers.
•
EN
5
i FUSE: 30AX1
3 Installation
j POWER
•
To connect +12V-DC power wire,
ground wire, and remote control
wire.
Note
• Follow all mounting and wiring instructions.
Mount the amplifier in car
You can mount the amplifier either under a seat
or on the rear tray.
Note
• To avoid interference, do not place the
amplifier too close to the car audio or antenna.
• The supplied mounting screws are 25mm long.
Make sure that the mounting board is thicker
than 25mm.
1 Place the unit on the location for
installation.
2 Mark the positions of the four screw
holes.
3 Drill the holes with driller of
approximately 4mm in diameter.
4 Mount the unit with the supplied screws.
6
EN
Connect speakers
Connect car audio
Option 1: Line input connection
Connect the amplifier to the car audio with an
RCA cable (not supplied).
Note
• Use speakers with an impedance of 2 to 8 ohm
(4 to 8 ohm when used as a bridged amplifier).
• Match the “left”, “right”, “+” and “-” terminals
correctly. Revised polarity may degrade sound
quality.
Car audio unit
LINE OUT
Option 1: Stereo mode: connect 2 speakers
(30A)
Option 2: Line output connection
Connect the amplifier to another amplifier.
4 ohm
4 ohm
speaker
speaker
Option 2: Mono bridged mode: connect
1 speaker
(30A)
Connect power
1 Make the power connection as illustrated
4 ohm
speaker
below:
•
•
•
Connect the ground wire from the
Option 3:Tri-mode: connect 3 speakers
car to the GND socket.
Connect the remote wire from the
car audio to the REM socket.
With this connection, you can turn
on/off the amplifier with the car
audio.
Connect the power wire from the
car battery to the +12V socket.
(30A)
4 ohm 4 ohm
speaker speaker
•
8 ohm speaker
EN
7
(30A)
To a metal point of the car
Less than 450mm (18 in)
Fuse (40A)
Remote output
Car audio unit
+12V car battery
Tip
• If your car audio does not have remote output,
connect the remote input terminal (REM) to
the accessory power supply.
8
EN
4 Use your power
amplifier
Adjust input level
To ensure sound quality, adjust input level to
match it with the car audio’s output voltage.
1 Check the line output voltage of the
connected car audio.
Select filter mode
Select Filter Mode according to the connected
speaker type.
2 Rotate INPUT LEVEL to select a matched
voltage: 0.3V to 6V.
1 Slide FILTER MODE to the selected
Adjust bass boost
To enjoy more bass sound:
position.
•
•
•
HPF (high-pass-filter): Select this
mode when mid-range speakers and
tweeters are connected for high
frequency output.
LPF (low-pass-filter): Select this
mode when woofer and subwoofer
are connected for low frequency
output.
1 Set FILTER MODE at OFF or LPF mode.
2 Slide BASS BOOST to 12dB position.
Tip
• If BASS BOOST is set at 0dB position, no extra
bass will be boosted.
OFF (flat): Select this mode when
both tweeters and woofers are
connected.
Note
• If FILTER MODE is set at HPF mode, the bass
frequency will be filtered.
Select LPF frequency
When FILTER MODE is set at LPF position, you
can select the range of frequency that is to be
filtered.
About the protector
indicator
The amplifier has a built-in protection circuit to
protect the transistors and speakers in following
conditions:
Note
• When FILTER MODE is set at OFF or HPF
position, LPF FREQUENCY does not work.
•
•
The amplifier is overheated.
A DC current is generated in
speakers.
1 Slide LPF FREQUENCY to the selected
position.
•
80Hz: More high frequency signal
is filtered. Select 80Hz if you prefer
stronger bass effect.
180Hz: Less high frequency signal is
filtered.
•
•
The battery voltage is too low or too
high. Or
The speaker terminals are short
circuited.
When the PROTECTED indicator
lights up in red, the amplifier shuts
down automatically. In this case
please:
•
EN
9
1 Take out the disc or tape and turn off the
5 Product
information
car audio.
2 Check the cause of the malfunction.
3 If the amplifier is overheated, let it cool
down.
Note
• Product information is subject to change
without prior notice.
Replace fuse
If there is no power, the fuse might be damaged
and need to be replaced.
Power output
(RMS)
- 4 ohm 75W x 2
1 Pull out the damaged fuse.
2 Replace the fuse with the supplied fuse or
buy a new fuse that matches the rating of
the damaged fuse (30A x 1).
- 2 ohm 110W x 2
- 4 ohm 220W x 1
(bridged)
Total harmonic
distortion
0.09%
Signal to noise
ratio
100dB
Channel separation
Frequency
response
50dB
5-50kHz
Input sensitivity
Input impedance
Fuse rating
Dimensions (D x
W x H)
300mV - 6V
22k ohm
30A x 1
246 x 240 x
54mm
If the fuse gets damaged immediately after it
has been replaced, the amplifier might have
internal malfunction. Consult qualified personal
for repair.
Weight
1.98kg
10 EN
6 Troubleshooting
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site
(www.philips.com/welcome).When you
contact Philips, ensure that the apparatus
is nearby and the model number and serial
number are available.
Power indicator does not light up
•
•
The connected car audio is not turned on.
The fuse is blown. Replace the fuse with
a new one.
The input level is not set correctly (see
“Adjust input level”).
•
The protector indicator lights up in red.
•
The speaker terminals are short circuited.
Check the speaker connections.
The sound is too low.
•
The input level is not set correctly
(see “Adjust input level”).
The sound is interrupted or stopped suddenly.
•
The thermal protector is activated.
Reduce the volume.
The ventilation outlet is blocked. Remove
any obstructions from the outlet.
•
Alternate noise is heard.
•
•
•
The power connecting wires are installed
too close to the RCA pin cords.
The ground wire is not securely
connected to a metal point of the car.
Negative speaker wires touch the car
chassis.
The unit becomes abnormally hot.
•
Place the amplifier in a well ventilated
location.
Use speakers with suitable impedance:
2-8 ohm (stereo), 4-8 ohm (bridged).
•
EN 11
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CMQ205_00_UM_V1.0
|