Philips CD Player AZ1032MP3 CD User Manual

MP3-CD Soundmachine  
AZ1032  
Meet Philips at the Internet  
User manual  
Manuel d’utilisation  
Manual del usuario  
Benutzerhandücher  
W
CLASS 1  
LASER PRODUCT  
Printed in China  
JH-0530  
 
3
4
5
7
8
9
X
C
B
A
A
6
0
 
The making of unauthorized copies of  
copy-protected material, including com-  
puter programmes, files, broadcasts and  
sound recordings, may be an infringe-  
ment of copyrights and constitute a crim-  
inal offence.This equipment should not  
be used for such purposes.  
Important notes for users in the U.K.  
Mains plug  
This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of  
plug proceed as follows:  
1. Remove fuse cover and fuse.  
2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.  
3. Refit the fuse cover.  
If the fitted plug is not suitable for your socket outlets, it should be cut off and an  
appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a  
value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board  
should not be greater than 3 Amp.  
Note:The severed plug must be disposed of to avoid a possible shock hazard should  
it be inserted into a 13 Amp socket elsewhere.  
How to connect a plug  
The wires in the mains lead are coloured with the following code: blue = neutral (N),  
brown = live (L). As these colours may not correspond with the colour markings  
identifying the terminals in your plug, proceed as follows:  
Environmental information  
All unnecessary packaging material has been omitted.The packaging can be easily separat-  
ed into three materials: cardboard, polystyrene and plastic.  
Connect the blue wire to the terminal marked N or coloured black.  
Connect the brown wire to the terminal marked L or coloured red.  
Do not connect either wire to the earth terminal in the plug, marked E (or e) or  
Your set consists of materials which can be recycled if disassembled by a  
specialized company. Please observe the local regulations regarding the  
disposal of packaging, dead batteries and old equipment.  
coloured green (or green and yellow).  
Before replacing the plug cover, make certain that the cord grip is clamped over the  
sheath of the lead - not simply over the two wires.  
Disposal of your old product  
Copyright in the U.K.  
Recording and playback of material may require consent. See Copyright Act 1956 and  
The Performer’s Protection Acts 1958 to 1972.  
Your product is designed and manufactured with high quality  
materials and components, which can be recycled and reused.  
When this crossed-out wheeled bin symbol is attached to  
a product it means the product is covered by the  
European Directive 2002/96/EC.  
Please inform yourself about the local separate collection system for electrical  
and electronic products.  
Please act according to your local rules and do not dispose of your old prod-  
ucts with your normal household waste.The correct disposal of your old prod-  
uct will help prevent potential negative consequences for the environment and  
human health.  
 
English  
Controls  
Power Supply  
Power supply  
@
#
$
STOP  
9
stops CD/MP3 playback;;  
erases a program  
Supplied Accessories  
– AC power cord  
– Remote control  
Using AC Mains  
Whenever convenient, use the mains lead if  
you want to conserve battery life. Make sure  
you remove the plug from the set and wall  
outlet before inserting batteries.  
1
2
Check if the mains voltage, as shown on  
the type plate located on the  
bottom of the set, corresponds to your  
local mains supply. If it does not, consult your  
dealer or service center.  
PLAY/PAUSE  
2/  
;
starts or pauses  
CD/MP3 playback.  
ALBUM+ /-  
Top and front panels  
(See 1)  
MP3 only: selects albums (up, down)  
% Display - shows disc functions  
Batteries (not included)  
1
2
Source selector: CD/MP3,TAPE/OFF,  
TUNER  
Connect the mains lead to the AC ~ inlet  
and the wall socket.The mains lead is now  
connected and ready for use.  
Main set (See 2)  
selects CD/MP3, tape or radio source of  
sound  
Back panel (See 2)  
^ Battery door - open to insert 6 x 1.5V  
Insert 6 batteries, type R-14, UM2 or  
C-cells (preferably alkaline) with the correct  
polarity.  
3
4
To switch the set off completely, withdraw  
the mains lead from the wall socket.  
power off switch  
R-14/ UM2/ C-cells.  
BASS BOOST  
turns the bass enhance-  
ment on/off.  
Install the unit near the AC outlet and where  
the AC power plug can be easily reached.  
& AC ~ - inlet for power cord.  
Remote control (See 2)  
* p – 3.5 mm stereo headphone socket  
Insert 2 batteries, type AA, R06 or UM3  
(preferably alkaline).  
3
4
VOLUME  
Cassette recorder keys:  
PAUSE ; pauses playback or recording  
STOPEJECT 9  
adjusts volume level.  
Helpful hints: The speakers will be muted  
when headphones are connected to the set.  
Disconnect the mains lead from the wall  
socket to protect your set during heavy  
thunderstorms.  
Incorrect use of batteries can cause  
electrolyte leakage and will corrode the  
compartment or cause the batteries to  
burst:  
( Telescopic antenna - improves FM  
/
reception  
stops playback or recording.  
The type plate is located on the bot-  
opens the cassette holder.  
tom of the set.  
F.FWD/REW 5 or 6  
fast winds/rewinds  
the tape  
Remote control (for disc oper-  
Do not mix battery types: e.g. alkaline with  
carbon zinc. Only use batteries of the same  
type for the set.  
Helpful hints :  
ations only) (See 2)  
To avoid unnecessary energy consumption,  
always adjust the Source selector to  
TAPE/OFF after using the set. Also check  
that the tape deck keys are released.  
PLAY 1  
REC 0  
starts playback  
1 MODE – selects different play modes:  
e.g. REPEAT or RANDOM  
(random order)  
2 PROG – programs tracks and reviews the  
program  
3 ALBUM +  
MP3 only: selects albums (up);  
4 ALBUM -  
starts recording  
When inserting new batteries, do not try to  
mix old batteries with the new ones.  
5 LIFTTO OPEN – lift here to open the  
CD door.  
Remove the batteries if the set is not to be  
used for a long time.  
6
TUNING – tunes to radio stations  
For users in the U.K., please follow the  
boxed instructions ‘Important notes...’ .  
7 BAND selects wavebands  
Batteries contain chemical substances,  
so they should be disposed of properly.  
8
9
iR infrared sensor for remote control  
CAUTION  
MP3 only: selects albums (down)  
MODE selects different play modes:  
for example:. REPEAT or RAN-  
DOM (random order)  
Use of controls or adjustments or per-  
formance of procedures other than  
herein may result in unsafe operation.  
5 PLAY/PAUSE – starts/ pauses CD/MP3  
playback  
6 STOP stops CD/MP3 playback;  
erases a program.  
7 ∞ §  
0
NEXT, PREVIOUS §, ∞  
CD/MP3: searches back and forward  
This set complies with the radio inter-  
ference requirements of the European  
Union.  
within a track;  
CD/MP3: searches back and forward  
skips to the beginning of a  
current track/ previous/ later  
track  
within a track;  
skips to the beginning of a  
current track/ previous/ later  
track  
!
PROG – programs tracks and reviews the  
program  
 
Basic Operation/Tuner  
Basic operation  
CD/MP3 player  
CD/MP3 Player  
Playing a disc  
Selecting a different track  
Press NEXT, PREVIOUS §, once or  
repeatedly until the desired track number  
appears in the display.  
About MP3  
This player plays Audio Discs including CD-  
R/ CD-RW, and MP3 CD. Do not try to play  
a CD-ROM, CD-I, CDV,VCD, DVD or  
computer CD.  
The music compression technology MP3  
(MPEG1 Audio Layer 3) significantly reduce  
the digital data of an audio CD while main-  
taining CD quality sound.  
Switching on and off and selecting  
functions  
1
2
To switch on, push the Source selector  
slider to CD, TUNER, or TAPE/OFF as  
desired.  
For MP3: first press ALBUM+ /- once or  
more to find your album.  
The display shows ALBUM and current  
album number briefly (See 5)  
Getting MP3 files: you can either down-  
load legal music files from the internet to  
your computer hard disc, or create such files  
by converting audio CD files in your com-  
puter through appropriate encoder software.  
(128kbps bit rate or higher is recommended  
for MP3 files.)  
IMPORTANT!  
To switch off, push the Source selector  
slider to TAPE/OFF and check the cassette  
keys are released.  
For a disc with CD Audio tracks and  
MP3 files, only the CD Audio tracks will  
be played.  
In the pause/stop position, press  
PLAY/PAUSE 2/; to start playback..  
Helpful hints:  
This player does not support UDF for-  
mat CD.  
To change from TAPE to TUNER or CD  
function, or when you are switching off the set:  
first, make sure you press the tape  
STOPEJECT 9/ key to end playback and  
all the cassette keys are released.  
Finding a passage within a  
track  
During playback, press and hold § or .  
Creating a MP3 CD: burn the music files  
from your computer hard disc on a CDR or  
CDRW using your CD burner.  
1
Lift the CD door at LIFTTO OPEN.  
Insert a CD with the printed facing up and  
press the CD door gently.  
1
2
The CD is played at high speed and low  
volume.  
2
3
Push the Source selector slider to  
CD/MP3.  
Display shows --- and later, the total num-  
ber of tracks.  
Helpful hints:  
Make sure that the file names of the MP3  
files end with .mp3.  
Adjusting volume and sound  
Adjust the sound with the VOLUME and  
BASS BOOST controls.  
When you recognize the passage you want,  
release § or to resume normal playback.  
Total number of music files and albums:  
around 350 (with a typical file name length of  
20 characters)  
Press PLAY/PAUSE 2/; to start playback.  
Audio CD: current track number appears  
MP3:The display shows current track  
number in the album (See 3)  
Different play modes:  
REPEAT and RANDOM  
(See 6 - 8)  
The length of file names affects the number of  
tracks for playback.With shorter file names,  
more files can be burned on a disc.  
Radio reception  
4
5
To pause playback, press PLAY/PAUSE  
2/; (See 4). Press PLAY/PAUSE 2/;  
again to resume play.  
1
2
Adjust the Source selector to TUNER.  
REP. plays the current track  
continuously  
REP.ALL repeats the entire disc/  
program  
RAND tracks of the entire disc are  
played in random order  
For MP3 only:  
REP.ALBUM all tracks of current album  
play repeatedly.  
To select play mode, press MODE once or  
more.  
The display shows the selected mode.  
Press PLAY/PAUSE 2/; to start playback.  
if in the stop position.  
To select normal playback, press MODE  
repeatedly until the various modes are no  
longer displayed.  
Adjust BAND to select your desired  
waveband, MW or FM ST. (stereo)  
To stop playback, press STOP 9.  
3
Turn TUNING to tune to a station.  
Helpful hints:  
To improve radio reception:  
CD play will also stop when:  
the CD door is opened  
the CD has reached the end  
you select tuner or tape source.  
For FM, extend and turn the telescopic  
antenna for best reception. Reduce its length  
if the signal is too strong.  
1
To tune to a weak FM station, adjust  
BAND to FM (mono).  
2
3
For MW, the set uses a built-in antenna.  
Direct this antenna for best reception by  
turning the whole set.  
You can also press STOP 9 to cancel your  
play modes..  
 
CD/MP3 Player  
Cassette Recorder  
Recording from the CD Player  
5 Repeat steps 2 to 4 to select and store all  
desired tracks in this way.  
Display shows PROG---after 10 tracks  
are stored.  
Cassette playback  
Push the Source selector slider to TAPE  
Programming track num-  
bers  
1
2
Select CD/MP3 source.  
1
2
You may store up to 20 tracks  
Insert a CD and if desired, program track  
numbers.  
Press STOPEJECT 9// to open the  
cassette holder and insert a cassette and  
close the deck.  
(for MP3: 10 tracks) in the desired sequence.  
If you like, store any track more than once.  
6
To play your programme, press  
PLAY/PAUSE 2/;  
3
Press 9// to open the cassette holder.  
Insert a blank tape and close the deck.  
.
For Audio CD:  
3
4
Press PLAY 1 to start playback.  
1
2
3
In the stop position, press PROG to acti-  
vate programming.  
Display: PROG and P01 flash, indicating  
the start of the program. (See 9)  
4
5
Press REC 0 to start recording.  
Helpful hints:  
When the PROG or RAND mode is active,  
To pause playback press PAUSE ;  
To resume, press the key again.  
.
Press PLAY/PAUSE2; to start CD play-  
back.  
use of the ALBUM+ /- keys are void  
.
5
To stop the tape, press 9//.  
6
7
For brief interruptions press  
recording, press again.  
;.To resume  
Press  
§
or  
to select your desired track  
Fast forwarding/rewinding  
;
Reviewing the program  
number.  
1
2
Press F.FWD/REW 5 or 6 unti you  
reach your desired passage.  
In the stop position, press PROG repeatedly  
until you enter the empty program location  
The display shows the occupied program  
locations  
To stop recording, press 9//.  
Display: PROG and your desired track  
number flash.  
Press 9// to stop fastforwarding/rewinding.  
Recording from the Radio  
Press PROG to store the desired track  
number.  
1
2
Select TUNER source.  
Helpful hints:  
After the empty program location is  
displayed, all the stored tracks appear in  
sequence.  
Tune to the desired radio station (see  
Radio reception).  
Display: PROG and P02 flash, indicating  
the next program location available.  
During playback, the keys are automatically  
released at the end of a tape and the set is  
switched off (unless PAUSE ; mode has been  
activated.)  
3
Follows steps 3, 4, 6,7 under Recording  
from the CD Player..  
4
Repeat steps 2 to 3 to select and store all  
desired tracks in this way.  
Display shows PROG---after 20 tracks  
are stored  
MP3 only: ALBUM and an album number  
appear, then a stored track number in the  
album is displayed.  
During fast forwarding/rewinding, the keys will  
not be released at the end of a tape.To switch  
off the set, make sure the cassette keys are  
also released..  
5
1
To play your programme, press  
Helpful hints:  
PLAY/PAUSE 2/;  
.
Display shows P01 if no track isprogrammed.  
For MP3:  
Erasing the program  
You can erase the contents of the memory  
by:  
In the stop position, press PROG to acti-  
vate programming.  
Display: PROG and P01 flash, indicating  
the start of the program.  
General information on recording  
Recording is permissible insofar as copyright  
or. other rights of third parties are not  
infringed.  
– pressing STOP  
9
(twice during playback  
or once in the stop position);  
2
3
4
If necessary, press ALBUM+ /- to select  
another album  
Display: ALBUM and selected album  
number (See 0)  
For recording, use only NORMAL type cas-  
settes (IEC type I) on which the tabs have  
not yet been broken.This deck is not suited  
for recording on CHROME (IEC II) or  
METAL (IEC IV) type cassettes.  
– selecting TUNER or TAPE sound  
source;  
– opening the disc door;  
Display: PROG disappears.  
Press  
§
or  
to select your desired track  
number.  
The best recording level is set automatically.  
Altering the VOLUME or BASS BOOST  
will not affect the recording.  
Display: the selected track number  
in current album  
Press PROG to store the desired track  
number.  
To protect a tape from accidental erasure,  
break out the tabs. If you wish to record  
again, cover the tabs with a piece of adhesive  
tape.  
Display: PROG and P02 flash, indicating  
the next program location available.  
 
Troubleshooting  
Maintenance & safety (see !)  
If a fault occurs, first check the points listed below before taking the set for repair.  
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.  
Safety information  
CD player and CD handling  
Place the set on a flat, hard and stable sur-  
face so that the system does not tilt.  
If the CD player cannot read CDs correctly,  
use a cleaning CD to clean the lens before  
taking the set to repair.  
WARNING:  
Do not open the set as there is a risk of electric shock. Under no  
circumstances should you try to repair the set yourself, as this will  
invalidate the guarantee.  
Do not expose the set, batteries, CDs to  
humidity, rain, sand or excessive heat caused  
by heating equipment or direct sunlight.  
The lens of the CD player should never be  
touched!  
The apparatus shall not be exposed to drip-  
ping or splashing.  
No sound /power  
CD-R/CD-RW is blank or not finalized  
Sudden changes in the surrounding  
Volume not adjusted  
Use a finalized CD-R or CD-RW only  
temperature can cause condensation on the  
lens of your CD player. Playing a CD is then  
not possible. Do not attempt to clean the  
lens but leave the set in a warm environ-  
ment until the moisture evaporates.  
• Adjust theVOLUME  
Adequate ventilation with a minimum gap of  
15cm (6 inches) between the ventilation  
holes and surrounding surfaces is necessary  
to prevent heat build-up.  
Note:  
Power cord not securely connected  
• Connect the AC power cord properly  
Batteries dead/ incorrectly inserted  
• Insert (fresh) batteries correctly  
Headphones connected to the set  
Make sure the CD is not encoded with  
Copyright protection technologies, as some  
do not conform to the Compact Disc stan-  
dard.  
Do not cover the ventilation openings with  
items such as newspapers, table-cloths, cur-  
tains, etc.  
Always close the CD-tape door to avoid  
dust on the lens.  
Disconnect headphones.  
The CD skips tracks  
CD damaged or dirty  
• Replace or clean CD  
PROG/ RAND is active  
• Quit PROG/ RAND mode  
To clean the CD, wipe in a straight line from  
the center towards the edge using a soft,  
lint-free cloth. Do not use cleaning agents as  
they may damage the disc.  
No objects filled with liquids, such as vases,  
shall be placed on the apparatus.  
Display does not function properly/ No  
reaction to operation of any of the con-  
trols  
No naked flame sources, such as lighted can-  
dles, should be placed on the apparatus.  
Electrostatic discharge  
Never write on a CD or attach any stickers  
to it.  
• Switch off and unplug the set. Reconnect after a  
few seconds  
The mechanical parts of the set contain  
self-lubricating bearings and must not be  
oiled or lubricated.  
Note:  
For a disc with CD Audio tracks and MP3  
files, only the CD Audio tracks will be  
played.  
Tape deck maintenance  
Remote control does not function  
properly  
To clean the set, use a dry cloth. Do not use  
any cleaning agents containing alcohol,  
ammonia, benzene or abrasives as these may  
harm the housing.  
To ensure quality recording and playback of  
the tape deck, clean parts A, B and C as  
shown, once a month. Use a cotton bud  
slightly moistened with alcohol or a special  
head cleaning fluid to clean the deck.  
Batteries exhausted/ incorrectly inserted  
Insert (fresh) batteries correctly  
Distance/ angle between the set too large  
Reduce the distance/ angle  
The MP3-CD skips albums  
CD contains non-MP3 file folders  
• Check your disc contains suitable file folders.  
1
2
3
Open the cassette holder by pressing  
9/.  
Severe radio hum or noise  
Poor cassette sound quality  
Press 1 and clean the roller C.  
Electrical interference: set too close to TV,VCR or  
computer  
Increase the distance  
Dust and dirt on the heads, etc.  
• Clean deck parts, see Maintenance  
Use of incompatible cassette types (METAL or  
CHROME)  
Press  
;
and clean the heads A, and the  
capstan B.  
4
After cleaning, press  
9/.  
Cleaning of the heads can also be done  
by playing a cleaning cassette through once.  
Poor radio reception  
• Only use NORMAL (IEC I) for recording  
Weak radio signal  
FM:Adjust the FM telescopic aerial  
Recording does not work  
Cassette tab(s) may be broken  
• Apply adhesive tape over the missing tab space  
noindication  
No disc inserted  
Insert asuitable disc  
CD badly scratched or dirty  
Replace/ clean CD, see Maintenance & Safety  
Laser lens steamed up  
• Wait until lens has cleared  
 

Peavey Microphone AAM 535 User Manual
Pelco TV Mount c971M c User Manual
Pentax Camcorder 735 User Manual
Philips Baby Monitor M2922A User Manual
Philips Refrigerator AZ9217 User Manual
Pioneer Portable CD Player PD F19PD F17 User Manual
Planet Technology Network Card WNL U553 User Manual
Playskool Games 08662 User Manual
Polaroid TV DVD Combo FDX 0700T User Manual
Power Acoustik Home Theater System RW1 10 User Manual