Open Ceiling Speaker
HP590i
Preliminary Technical Information for System Engineers
Key Features
• High-power output (108.5 dB) for longer
throw and higher SPL requirements.
• One 133 mm (5.25 in) polypropylene
woofer and one 25 mm (1.0 in) horn-
loaded convex aluminum dome tweeter
mounted to a proprietary cast-alumi-
num HP5TM baffle & heat sink.
Mounting hardware included
Specifications: HP590i
System Type
5.25” Coax, open-ceiling, ported (33 Watt transformer for
25/70.7/100 Volt or voice coil / 8 Ohm direct)
74 Hz - 22 kHz
64 Hz - 20 kHz
160 Watts
80 Watts
108.5 dB
• 89.5 dB Average sensitivity offers
high output capabilities and reduced
amplification costs.
Frequency Response (- 3 dB)1
Low Frequnecy (-10 dB)1
Max. Program Power
• Weatherized components for indoor/out-
door applications.
Max. Continuous Power2
Max. SPL dB @ 1 M
Sensitivity dB @ 1W/1M3
Impedance (nominal)
Coverage Angle (-6 dB @ 500 Hz)
Coverage Angle (-6 dB @ 4 kHz)
Directivity Factor (Q)
89.5 dB
8 Ohm (nominal value)
360º (average)
96º (average)
6.56 (Averaged 100 Hz - 10 kHz); 9.31 @ 2 kHz
6.01 dB (Averaged 100 Hz - 10 kHz); 9.69 dB @ 2 kHz
6-Position rotary switch with voice coil direct (8 Ohm)
• Includes hanging hardware with
aircraft cables and integrated Speed-
ClampTM self-locking wire grip for fast,
easy & secure installation. Also includes
Euroblock connector & terminal weather
boot.
Directivity Index (DI)
Tap Selector
• Easy access 6-position selectable tap
switch for 25, 70.7 & 100 Volt applica-
tions with voice coil/8 Ohm direct sim-
plifies ordering and inventory tracking.
Transformer Taps
70.7 V Output
33 W 104.5 dB
17 W 102 dB
9 W 99 dB
6 W 97.5 dB
3 W 94.5 dB
100 V Output
33 W 104.5 dB
17 W 102 dB
9 W 99 dB
25 V Output
5 W 96.5 dB
2.5 W 93.5 dB
1.3 W 90.5 dB
0.63 W 87.5 dB
• High quality black or white paint finish.
6 W 97.5 dB
Description
Transducers
The HP590i is a high-powered 5.25”
2-way horn-loaded loudspeaker in a
ported open-ceiling enclosure design.
The HP590i incorporates a low-profile
grille, proprietary HP5TM motor-board
and 6-position tap switch with voice
coil/8 Ohm direct. Hanging hardware
is included and features a fast- action
SpeedClampTM for easy and secure
installation.
Low Frequency Driver
High Frequency Driver
Low Frequency Voice Coil
Crossover Frequency
1 x 133 mm (5.25 in) Polypropylene cone, butyl rubber surround
25 mm (1.0 in) Convex aluminum horn-loaded tweeter
25 mm (1.0 in)
3 kHz
Network Type
Low Pass
High Pass
Enclosure Material
Motor Board
Grille
N/A
12 dB per octave, 2nd order
Drawn aluminum backcan with ABS baffle
Cast aluminum
Iridite-plated steel with powder-coat finish
4 Pin, 5 mm Euroblock for individual or daisy chain connection
Black or white
Inputs
Colors
Applications
Height
Width (including bracket)
Weight
298.3 mm / 11.74 in
245.9 mm / 9.68 in
4.3 kG / 9.5 lbs
10 kG / 22.0 lbs (2 per box)
Engineered for high-SPL and effective
low-end response (64 Hz @ - 10 dB), the
HP590i delivers consistent foreground
music, sound reinforcement and PA for
applications requiring longer throw
or higher volume. For indoor/outdoor
applications, the HP590i incorporates
a powder-coated, iridite-plated steel
grille, polypropylene driver and durable
enclosure design. The HP590i is ideal for
open-ceiling music & paging applications
with high ambient noise levels including
casinos, warehouses, airports, transporta-
tion & shipping centers, schools, gyms,
arenas and stadiums. For additional bass,
SoundTube’s RS801i subwoofer offers bass
response to 40 Hz.
Shipping Weight
Accessories
Included
Hanging hardware, Euroblock connector & terminal
weather boot
N/A
Optional
Packaging
2 Per box, can ship as single
1
2
3
Frequency response is measured in full space and includes a low-frequency peak > + 3 dB.
Continuous power rating, EIA-426-B test.
2.83 Volts at a distance of 1 meter.
SoundTube continually develops new product innovations and improvements. Updates to existing
products without prior notice are an example of SoundTube’s drive for constant improvement.
© 2006 SoundTube Entertainment. All rights reserved. PN TS-HP590 REV 03.03.06
Open Ceiling Speaker
HP590i
Preliminary Technical Information for System Engineers
Center (TMC) are analyzed using a vari-
ety of standard measurement techniques,
including Measured Length Sequence
(MLS) and Time Delay Spectrometry
(TDS). Performance, development and
data acquisition tools include: Gold Line
TEF 20, CLIO, LMS, LEAP, and propri-
etary modeling software. EASE™ data
are acquired through an automated TEF
20/Outline/EASE™ interface.
from 10 – 22 gauge wire. The system shall
be for indoor & outdoor applications and
have a weather-resistant terminal booth
covering all wire connectors.
Volt input, 1 meter) shall be at least 89.5
dB. The speaker shall have a nominal
impedance of 8 Ohms and shall be avail-
able for 25/70.7/100 Volt modes with
voice coil/8 Ohm direct. The frequency-
dividing network shall have a crossover
frequency of 3 kHz with a slope of 12 dB
per octave (second order) for the high-
pass filter. Rated power capacity shall
be at least 80 Watts continuous power
(RMS), and conforms to EIA-426-B test-
ing. Maximum continuous output at 1
meter shall be 108.5 dB.
The enclosure shall be constructed of
injection-molded glass-reinforced ABS.
The grille shall be constructed of iridite-
plated, powder-coated steel for lasting
performance in the elements. Overall
cabinet dimensions shall be no more than
298.3 mm (11.74 in) in height by 245.9 mm
(9.68 in) in diameter. The HP590i shall
include hanging hardware, Euroblock
connector and terminal weather boot.
EASE™ Data – 3-D polar plots.
SoundTubeSPEC™ – Proprietary
SoundTube speaker placement software.
The low-frequency transducer shall
have a polypropylene cone with butyl
rubber surround. The high-frequency
transducer shall be constructed of alu-
minum material and incorporate a high-
SPL 90º horn.
Architectural Specifications
The system shall be the SoundTube
HP590i with hanging hardware for both
low & high impedance applications.
The loudspeaker shall consist of a
133 mm (5.25 in) low-frequency trans-
ducer and a 25 mm (1 in) high-frequency
transducer with a frequency-dividing net-
work installed in a ported enclosure. The
low-frequency voice coil diameter shall be
25 mm (1 in).
SoundTube Entertainment
Installation for the HP590i shall be
by aircraft cable affixed to the speaker
chassis via a hook. For seismic & safety
redundancy, a secondary aircraft cable
shall be included and shall attach to
the speaker chassis via a #10 bolt. The
external wiring input connector shall
be a 4-pin, 5 mm Euroblock for 8 Ohm
or distributed systems and shall accept
6430 North Business Park Loop
Park City, Utah 84098
Phone 435.647.9555
Fax
435.647.9666
Performance specifications of a typi-
cal production unit shall be as follows:
Useable frequency response shall extend
from 64 Hz – 22 kHz (-10 dB, no external
equalization). Measured sensitivity (2.83
Toll Free 800.647.TUBE
Polar Plots
250 Hz
500 Hz
1,000 Hz
125 Hz
4,000 Hz
8,000 Hz
10,000 Hz
2,000 Hz
™
™
Technical data, EASE plots, SoundTubeSPEC software & product downloads available at www.soundtube.com
Open Ceiling Speaker
HP590i
Preliminary Technical Information for System Engineers
Mechanical Drawings
298.3 mm
(11.74 in)
245.9 mm (9.68 in)
Included Accessories
Hanging Hardware: Main & Safety
Cables w/ SpeedClamp™
SoundTube’s hanging cable kit incorpo-
rates hanging & safety cables & Speed-
Clamp™ self-locking cable clamps for
an integrated and easy-to-install system.
Hanging & safety cables are infinitely
adjustable to 2.74 M (9.0 ft).
SoundTube Entertainment manufactures a complete line of speakers for:
Open-Ceiling • In-Ceiling • Surface-Mount • Outdoor • Sound-Focusing
All SoundTube products are designed and engineered in the USA.
|