Perlick Beverage Dispenser US10KP User Manual

INSTALLATION AND OPERATION INSTRUCTIONS  
UTILITy COOLERS  
MODEL NOS.  
US4KP  
US10KP  
IMPORTANT INFORMATION  
Table of Contents  
Cabinet Specifications......................................... 2  
Preparing for Assembly  
This manual has been prepared to assist you  
in the installation of your Utility Cooler and to  
acquaint you with its operation and maintenance.  
Tools Required .................................................... 3  
Pre-Assembly....................................................... 3  
Placing the Utility Cooler ..................................... 3  
Cam Lock Fastening Method ............................. 3  
Assembling the Cooler  
Preparing the Floor .............................................. 4  
Assembly.............................................................. 4  
Assembly Order-Four Keg Cooler........................ 5  
Assembly Order-Ten Keg Cooler ......................... 6  
General Information  
Electrical Requirements....................................... 7  
Starting the Cooler............................................... 7  
Temperature Control ............................................ 7  
Ventilation Requirements ..................................... 7  
Cleaning the Condensing Unit............................. 7  
Warranty Information ........................................... 7  
Replacement Parts ............................................. 8  
Wiring Diagrams  
We dedicate considerable time to ensure that our  
products provide the highest level of customer  
satisfaction. If service is required, your dealer  
can provide you with a list of qualified service  
agents. For your own protection, never return  
merchandise for credit without our approval.  
We thank you for selecting a Perlick product and  
assure you of our continuing interest in your  
satisfaction  
IMPORTANT WARRANTy INFORMATION  
To register your product, visit our web site at  
“Service”. You will see the link to “Warranty  
Registration Form”. You must complete and submit  
this form or the installation date will revert back to  
the ship Date.  
Four Keg Self-contained...................................... 9  
Ten Keg Self-contained...................................... 10  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Form No. Z2026  
Rev 01.28.09  
 
Preparing the Cabinet for Use  
Tools Required  
The Cam Lock Fastening Method  
Tape Measure.  
Chalk Line.  
This utility cooler utilizes the cam-lock fastening  
method. (See illustration on below.)  
Caulking Gun.  
Caulk (provided).  
Clam Lock Wrench (provided).  
Level.  
Screw Driver.  
Shims.  
Insert the cam lock wrench into the lock before the  
panels are pushed together. Turn the handle Cam  
Hole counterclockwise as far as it will go to fully  
cock the  
cam. Note: The cam must be fully cocked to  
assure proper locking. The panels should then be  
pushed together tightly and locked by turning the  
wrench clockwise.  
Pre-Assembly  
Some panels have been protected with a strip-  
pable film to prevent surface damage. Remove this  
film before assembly. It is very difficult to remove it  
from the panel edges after panels have been joined  
together. Note: Do not store panels with protective  
film in sunlight or high temperature areas for an  
extended period of time.  
Plugs are provided to insert in cam-lock holes after  
final assembly.  
CAM  
CAM  
HOLE  
Placing the Utility Cooler  
This utility cooler should not be installed tight  
against any building or adjacent cooler wall. A  
minimum of two inches must be provided for air  
circulation. Shims for leveling the floor must  
also be incorporated into overall height and  
clearance requirements.  
Remote Units: A minimum four inch clearance is  
required between the top of the utility cooler  
and the ceiling of the building in which it is being  
installed.  
Self-contained Units: Sufficient clearance above the  
cooler must be allowed for ceiling panel  
and condensing unit installation. For ventilation  
requirements, see page 7.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
3
 
General Information  
Preparing the Floor  
Assembly  
Snap a chalk line on the building floor to establish  
cooler location. Place floor panel(s) on the floor and  
check for level. A level floor is essential to ensure  
that vertical panels will be plumb. If shimming  
is required to level the sections, the shims must  
extend under the entire section, not just the edges.  
Shims should be used at each end, at all wall  
seams, and at each floor seam. They should not be  
spaced further than 24 inches apart.  
1. Place (do not slide) all sections into position.  
2. Each panel is numbered on the edge. For a four  
keg cooler, follow the assembly order on page  
5. For a ten keg cooler, the assembly order  
appears on page 6.  
Note: If ceiling height in building is restricted,  
panel(s) can be carried through the door open-  
ing and placed into position from inside the  
cooler.  
3. Install cap plugs in all cam-lock holes.  
4. Seal cooler to the floor.  
CEILING  
KEEP GASKETS  
OUT OF GROOVE  
SEAL COOLER TO FLOOR  
AFTER UNIT IS LEVEL AND  
ASSEMBLED  
FLOOR PANEL  
FLOOR  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
4
 
Four Keg Cooler  
Four Keg Cooler Assembly  
Assemble panels as follows:  
Section 1:.............. Floor  
Section 6:.............. Front with Door  
Section 5:.............. Right Wall  
Section 7:.............. Ceiling  
Section 2:.............. Left Wall  
Section 3:.............. Left back Wall  
Section 4:.............. Right back Wall  
3
4
UNIT  
COOLER  
1
5
2
FLOOR  
6
PANEL NO.#’S  
7
FRONT VIEW  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
5
 
Ten Keg Cooler  
Ten Keg Cooler Assembly  
Assemble panels as follows:  
Section 1 & 2:........ Floor-Section  
Section 3: .............. Left Wall  
Section 7: .............. Door Section  
Section 8: .............. Left Front Panel  
Section 4: .............. Left back Wall  
Section 5: .............. Right back Wall  
Section 3A:............ Right Wall  
Section 6: .............. Right Front Wall  
Section 9: .............. Celing Panel with  
Evaporator Housiing  
Section 10: ............ Celing Panel  
4
5
PANEL NO.#’S  
3A  
1
3
2
9
10  
COOLER  
6
8
7
9
10  
FRONT VIEW  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
6
 
General Information  
There should be nothing on or around the machin-  
ery compartment area which will restrict the flow of  
room temperature air to the condenser or over the  
compressor.  
Electrical Requirements  
The package unit must be installed so that the wir-  
ing conforms to, and is in accordance with National  
and Local Electrical Codes. (See Condensing Unit  
Data Plate for Electrical Specifications.  
Natural  
Forced Air  
Circulation Cu.  
Circulation C.F.M.  
CAUTION: Do not attempt to operate the condens-  
ing unit on any other power source than that listed  
on the unit data plate. See appropriate wiring dia-  
gram on pages 9, 10 or 11.  
Compressor H.P.  
Ft. Room Volume Fresh Air Entering  
Needed  
Room  
1/3 to 1/2  
600  
220  
Cleaning the Condensing Unit  
Starting The Cooler  
Inspect the machinery compartment every 60 days.  
A heavy accumulation of dirt and/or grease on  
the front of the condensing unit (radiator) must be  
cleaned off with a stiff brush or vacuum cleaner. be  
careful not to bend the aluminum fins on the con-  
densing unit.  
Allow the empty utility cooler to operate 24 hours  
for a settling-out period before use.  
Temperature Control  
The temperature control is located on the evapo-  
rator housing. It is factory adjusted to maintain a  
temperature of approximately 34° F. cut out and  
40° F. cut in. Cut out temperatures lower than 34°F.  
are not advisable as excessive frost may accumu-  
late on the evaporator.  
Warranty  
This Utility Cooler is fully warranted against defects  
in both material and workmanship for a period  
of one (1) year from date of sale. Defective parts  
must be returned to Perlick freight prepaid. All  
parts found to be defective upon inspection will be  
replaced on a no-charge basis, F.O.b. our factory.  
Perlick is not responsible for parts damaged by  
alteration, unauthorized service, accident or abuse.  
All costs incident to replacement, including labor,  
refrigerant, and/or loss of sales are incidental to  
this warranty and must be borne by the user.  
If excessive frost does accumulate, the unit is  
operating at too cold a temperature. To defrost the  
evaporator, turn off the electrical power to the con-  
densing unit or turn the control to a warmer posi-  
tion to allow the fan motor to defrost it. The control  
should then be reset to a temperature that will not  
ice up the evaporator. A plastic drain hose should  
be attached to the drain pan of the evaporator and  
routed through the wall panel. A receptacle should  
be provided for accumulated condensing water or  
connect to a building drain facility.  
Ventilation Requirements  
Air-cooled units must be furnished with sufficent  
ventilation to maintain their efficiency. The table  
at right indicates the minimum room size/cubic  
footage, only the space above the condensing  
unit can be used. When the room size is below  
minimum, some type of forced ventilation must  
be provided.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
7
 
Replacement Parts  
be prepared to provide the model and serial num-  
ber of the cooler. The serial number is  
printed on a label which is attached to the inside  
wall, adjacent to the evaporator housing.  
How to Order Replacement Parts  
Contact your local Perlick dealer to order  
replacement parts.  
SELF-CONTAINED UTILITy COOLERS  
FOUR KEG  
TEN KEG  
Description  
Compressor Only  
Part Number  
57499  
Description  
Compressor Only  
Part Number  
57860  
Condensing Unit Fan Motor  
Condensing Unit Fan blade  
Evaporator Coil Assembly  
E xpansion Valve  
57513  
Condensing Unit Fan Motor  
Condensing Unit Fan blade  
Evaporator Coil Assembly  
E xpansion Valve  
C15250A2  
C15250A3  
57872  
C3150-3  
57861  
57877  
57877  
Temp. Control (two-wired)  
57891  
Temp. Control (two-wired)  
57891  
ALL MODEL UTILITy COOLERS  
Description  
Part Number  
57878  
Description  
Evaporator Fan Guard  
Plug button  
Part Number  
57875  
Switch  
Light bulb  
C31358  
C25969-1  
57879  
57882  
bulb Guard  
Door Sill  
57883  
Thermometer  
Door Closure  
Light Indicator  
Hinge  
57884  
Hinged Door Assy.  
Gasket-Door Assy.  
Evaporator Fan Motor  
Evaporator Fan blade  
57880  
57858  
57881  
57885  
57873  
Handle  
57886  
57874  
Door Wiper Gasket  
57908  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
8
 
Wiring Diagram — Four Keg Self-Contained Cooler  
CAPACITOR  
COMPRESSOR  
TERMINALS  
GREEN  
C
2
1
BROWN  
WHITE  
L1  
L2  
S
R
RELAY  
OVERLOAD  
FAN  
GREEN  
BLACK  
WHITE  
SWITCH  
LIGHT  
WHITE  
BLACK  
WHITE  
BLACK  
BROWN  
WHITE  
(ELECTRONIC)  
THERMOSTAT  
(4 MIN. “ON” DELAY)  
EVAPORATOR  
FAN MOTORS  
BLACK  
(ALTERNATE)  
THERMOSTAT  
(STANDARD)  
BROWN  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
9
 
Wiring Diagram — Ten Keg Self-Contained Cooler  
1
5
2
L
CAPACITOR  
M
FAN  
CONDENSER  
RELAY  
OVERLOAD  
BLUE  
S
3
1
C
COMPRESSOR  
TERMINALS  
R
GREEN  
BLACK  
WHITE  
SWITCH  
LIGHT  
WHITE  
BLACK  
WHITE  
BROWN  
BLACK  
WHITE  
(ELECTRONIC)  
THERMOSTAT  
(4 MIN. “ON” DELAY)  
EVAPORATOR  
FAN MOTORS  
BLACK  
(ALTERNATE)  
THERMOSTAT  
(STANDARD)  
BROWN  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
10  
 
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2026  
Rev 01.28.09  
11  
 
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Form No. Z2026  
Rev 01.28.09  
 

Pentair Swimming Pool Filter FNS Plus User Manual
Peugeot Automobile 405EXECUTIVE User Manual
Philips Cell Phone VOIP433IB User Manual
Philips DVD Player DVD622 051 User Manual
Philips Electric Shaver T388 User Manual
Pioneer Car Stereo System DEH P3950MP User Manual
Pioneer Car Video System AVH P6000DVD User Manual
Polaroid Digital Camera PDC 700 User Manual
Poulan Snow Blower PP291E30 User Manual
Powermate Portable Generator PC049650317 User Manual