®
NET101RK
19-Inch PelcoNet™
Rack Mount Kit
Installation/
Operation Manual
C1978M (11/01)
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
DESCRIPTION
The NET101RK lets you mount several PelcoNet™ systems in one location. The 19-inch
rack mount kit has the following features:
•
•
•
•
Installation of up to eight PelcoNet systems
Simple integration of PelcoNet systems into existing 19-inch racks
Central plug-in power supply for all PelcoNet systems
Installation of PelcoNet transmitters and receivers in one rack mount kit
APPLICATIONS
RECEIVER
LAN
OR
MONITOR
WAN
WEB BROWSER OR A VIDEO
CONFERENCING SYSTEM
Figure 1. PelcoNet Applications
INSTALLATION
The NET101RK contains the following parts:
•
•
Mounting kit for 19-inch rack
Power cord
Figure 2. Connecting Electrical Power and Securing PelcoNet
1. Remove the feet from the PelcoNet unit.
2. Remove the nut and lock washer from the BNC connector on the PelcoNet unit.
3. Slide the PelcoNet unit through a bay at the back of the NET101RK. The PelcoNet’s
BNC connector should rest in the rounded cutout on the front of the NET101RK.
4. Refer to Figure 2. Plug the small electrical connector on the NET101RK into the top
receptacle marked “Power” on the back of the PelcoNet unit.
5. Refer to Figure 2. Slip the lock washer removed in step 2 onto the BNC connector. In-
stall the nut on the BNC connector and tighten.
6. Repeat steps 1-5 for each PelcoNet unit to be installed.
Pelco Manual C1978M (11/01)
3
7. Install the NET101RK in the rack and attach using appropriate hardware (not in-
cluded).
8. Make all other hookups to the PelcoNet units. (Refer to the PelcoNet Installation/
Operation manual for hookup instructions.)
9. Insert the included power cord into the back of the NET101RK. Plug the power cord
into an electrical outlet to apply power.
SPECIFICATIONS
Power Supply
USA:
Europe:
90-132 VAC, 57-63 Hz
180-264 VAC, 47-53 Hz
60W
Power Consumption:
Operating Temperature: 41-104°F (5-40°C) ambient temperature
Operating Humidity:
Housing Dimensions:
Weight:
20-80% atmospheric humidity (non-condensing)
18.8 (L) x 4.9 (D) x 5.2 (H) inches (47.8 x 12.5 x 13.3 cm)
Approximately 6.6 pounds (3 kg)
Standards:
EN 55022, EN 55024, EN 60950
(Design and product specifications subject to change without notice.)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date
C1978M 11/01
Comments
Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
©Copyright 2001, Pelco
All rights reserved.
4
Pelco Manual C1978M (11/01)
|