I N S T A L L A T I O N
EH2500 Series
Dust-Tight Enclosure
C1473M-E (9/08)
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Enclosure Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Camera and Lens Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power and Camera Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Reassemble the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
List of Illustrations
Typical Fixed Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Typical Fixed Ceiling Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Pan/Tilt Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Pan/Tilt Ceiling Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Enclosure Input Voltage 24 VAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Enclosure Input Voltage 120/230 VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
List of Tables
Total Wattage Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
24 VAC Wiring Distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Video Coaxial Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C1473M-E (9/08)
3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
7. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Installation should be done only by qualified personnel and conform to all local codes.
9. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.
10. Use only installation methods and materials capable of supporting four times the maximum
specified load.
11. Use stainless steel hardware to fasten the mount to outdoor surfaces.
12. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be
incorporated in the electrical installation of the building.
13. Use UL Listed cameras not to exceed 5 watts.
14. Only use replacement parts recommended by Pelco.
15. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock do not perform any servicing other that contained in the operating
instructions unless you are qualified to do so.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
CAUTION:
this unit.
RISK OF ELECTRIC SHOCK.
This symbol indicates that there are important
DO NOT OPEN.
operating and maintenance instructions in the
literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
4
C1473M-D (9/08)
Description
The EH2500 Series enclosures are sealed, dust-tight, and waterproof camera enclosures designed to
protect a camera and lens from adverse environmental conditions.
The EH2500 Series feature a sled for camera mounting and a “T” handle on the rear plate to assist in
removing the rear plate during installation and servicing.
All models will accept CCD cameras with fixed focal length or motorized zoom lenses.
MODELS
EH2508
Indoor/outdoor enclosure, 8-inch (20.32 cm) length
Same as EH2508 except has 120/24/230 VAC heater
Indoor/outdoor enclosure, 12-inch (30.48 cm) length
Same as EH2512 except has 120/24/230 VAC heater
Indoor/outdoor enclosure, 15-inch (38.10 cm) length
Same as EH2515 except has 120/24/230 VAC heater
EH2508-1/-2/-3
EH2512
EH2512-1/-2/-3
EH2515
EH2515-1/-2/-3
C1473M-D (9/08)
5
Installation
The following items are supplied:
Qty Description
1
1
1
1
1
2
EH2500 Series enclosure
Hex wrench, 3/32-inch (Pelco # ZT-ALLEN3/32)
Hex wrench, 5/64-inch (Pelco # ZT-ALLEN5/64)
1/4 x 1-inch O.D. fender washer
Desiccant bag
1/4-20 x 0.375-inch Phillips pan head screws and flat washers (for camera mounting; only one
screw and washer are required)
1
Installation manual (C1473M)
ENCLOSURE MOUNTING
The enclosure can be mounted to a wall, ceiling, or pedestal mount. It can also be mounted to a pan/tilt.
For proper installation, refer to the instructions supplied with the mount or pan/tilt. The enclosure should
be attached to the mount or pan/tilt with a minimum of two 1/4-20 fasteners (not supplied).
WARNING: If you are installing the enclosure outdoors, avoid mounting it at a downward angle to
ENCLOSURE
WALL MOUNT
WALL
Figure 1. Typical Fixed Wall Mounting
6
C1473M-D (9/08)
CAMERA AND LENS INSTALLATION
To install the camera and lens, perform the following steps:
1. Use the supplied 5/64-inch hex wrench and loosen the screws located on the back of the enclosure.
2. Pull on the “T” handle and slide the camera sled out of the enclosure.
WARNING: If you have a model with a heater, disconnect the heater wiring connectors
before removing the camera sled from the enclosure. Damage to the heater wires may occur
if the sled is pulled out too far before the wiring connectors are separated.
3. Mount the camera and lens onto the camera sled:
a.
b.
c.
Extend the lens to the maximum length before positioning the camera and lens.
Position the camera and lens so that they do not extend beyond the track.
Attach the camera and lens to the camera sled with the supplied fender washer, and one 1/
4-20 x 0.375-inch Phillips pan head screw and washer.
POWER AND CAMERA CONNECTIONS
NOTE: To prevent the entrance of dust or water, proper cabling must be used when wiring the enclosure.
Use of a flat cable or multiple cables will prevent the proper seal of the liquidtight gland connectors.
Outdoor-rated sheathing should cover multiple cables. It is especially important that you seal an unused
gland connector.
To make all power and camera connections, follow the steps below:
1. If the enclosure has a heater, refer to Table A on page 9 for total wattage, which includes camera
wattage. Maximum camera input voltage must not exceed 240 VAC, and maximum camera power
consumption must not exceed 5 W.
3. Pull the power wires for the heater and camera into the enclosure.
4. Connect the enclosure input power, camera input power, and video cable (refer to , , and Table C on
NOTES:
•
voltage for the enclosure and camera are different. For example, the enclosure input voltage
is 120 VAC and the camera input voltage is 24 VAC.
•
•
Be sure to route the wiring to maintain separation between 120/230 VAC, 24 VAC, and video
wiring.
However, you may have an application where the input voltage for the enclosure and camera
are the same. For example, the enclosure input voltage is 120 VAC and the camera input
voltage is 120 VAC. In applications where the input voltage for the enclosure and camera are
the same, wire the terminal block as follows:
–
–
Connect the input power for the enclosure to terminal 3 (AC LINE) and terminal 4 (AC
NEUTRAL).
Connect a jumper wire from terminals 1 to 3 and a jumper wire from terminals 2 to 4.
5. Connect the ground wire for the enclosure power to the ground stud on the back of the enclosure.
6. Attach the wires from the camera to the 2-pin camera power connector (supplied). Connect the two
camera power connectors together.
7. If the camera input voltage is 120 VAC/230 VAC, ground the camera to the ground stud located on
the camera sled.
8
C1473M-D (9/08)
Table A. Total Wattage Values
Maximum Power
Model
Voltage
120
24
Consumption*
EH2508-1
EH2508-2
EH2508-3
EH2512-1
EH2512-2
EH2512-3
EH2515-1
EH2515-2
EH2515-3
41
38
43
41
38
43
41
38
43
230
120
24
230
120
24
230
*Maximum power consumption includes 5 W for the camera.
Tables B and C show the recommended maximum distances for 24 VAC applications; the values are
calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop
for AC-powered devices.)
Table B. 24 VAC Wiring Distances
Wire Gauge
Total
VA
20
18
16
14
12
10
(0.5 mm2)
(1.0 mm2)
(1.5 mm2) (2.5 mm2)
(4.0 mm2)
(6.0 mm2)
10
20
30
40
50
283
(86)
451
716
1142
(348)
1811
(551)
2880
(877)
(137)
(218)
141
(42)
225
(68)
358
(109)
571
(174)
905
(275)
1440
(438)
94
(28)
150
(45)
238
(72)
380
(115)
603
(183)
960
(292)
70
(21)
112
(34)
179
(54)
285
(86)
452
(137)
720
(219)
56
(17)
90
(27)
143
(43)
228
(69)
362
(110)
576
(175)
C1473M-D (9/08)
9
Table C. Video Coaxial Cable Requirements
Cable Type*
RG59/U
Maximum Distance
750 ft (229 m)
RG6/U
1,000 ft (305 m)
1,500 ft (457 m)
RG11/U
*Cable requirements:
75-ohm impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
WHITE
BLACK
INPUT
POWER
ENCLOSURE
TERMINAL 4 (AC NEUTRAL)
TERMINAL 3 (AC LINE)
INPUT
TERMINAL 2
POWER
TERMINAL 1
ENCLOSURE
WHITE
PIN 2
PIN 1
PIN 2
PIN 3
RED
PIN 1
BLACK
WHITE
BLACK
PIN 2
PIN 1
CAMERA POWER
HEATING ELEMENT POWER
PIN 1 RED
PIN 2 BLACK
PIN 3 WHITE
Figure 5. Enclosure Input Voltage 24 VAC
10
C1473M-D (9/08)
WHITE
BLACK
INPUT
POWER
ENCLOSURE
TERMINAL 4 (AC NEUTRAL)
TERMINAL 3 (AC LINE)
INPUT
TERMINAL 2
POWER
TERMINAL 1
ENCLOSURE
WHITE
BLACK
PIN 1
PIN 2
PIN 3
PIN 2
PIN 1
RED
WHITE
BLACK
BLACK
FUSE
PIN 2
PIN 1
CAMERA POWER
HEATING ELEMENT POWER
PIN 1 RED
PIN 2 BLACK
PIN 3 WHITE
Figure 6. Enclosure Input Voltage 120/230 VAC
C1473M-D (9/08)
11
REASSEMBLE THE ENCLOSURE
1. Place the desiccant bag in the enclosure.
2. Slide the camera sled back into the enclosure.
3. Reinstall the screws in the rear plate.
MAINTENANCE
Regularly scheduled maintenance is not required. Clean the outer surface of the enclosure with a
nonabrasive cleaning cloth and antistatic cleaner. Clean the viewing window with a mild nonabrasive soap
and water to maintain picture clarity.
WARNING: Do not use kerosene or similar substances that may damage the surface.
12
C1473M-D (9/08)
Specifications
MECHANICAL
Camera Mounting
Latching
Multiple mounting holes on removable camera sled
2 captivated screws
Maximum Camera/Lens Size
Accepts camera and lens combinations (including BNC connector) up to
the following dimensions:
6.25" L x 2.75" W x 2.75" H
(15.88 x 6.99 x 6.99 cm)
EH2508
EH2508-1/-2/-3
EH2512
5.25" L x 2.75" W x 2.75" H
(13.34 x 6.99 x 6.99 cm)
10.25" L x 2.75" W x 2.75" H
(26.04 x 6.99 x 6.99 cm)
EH2512-1/-2/-3
EH2515
9.25" L x 2.75" W x 2.75" H
(23.50 x 6.99 x 6.99 cm)
13.25" L x 2.75" W x 2.75" H
(33.66 x 6.99 x 6.99 cm)
12.25" L x 2.75" W x 2.75" H
(31.12 x 6.99 x 6.99 cm)
EH2515-1/-2/-3
Viewing Window
Cable Entry
2.50" (6.35 cm) diameter, 0.375" (0.95 cm) thick Lexan®
2 liquid-tight gland connectors
ELECTRICAL
Input Voltage
Connector
Heater
120 VAC, 24 VAC, 230 VAC for heater
Terminal block, 4-position
120/24/230 VAC, dual elements, thermostatically controlled
Heater operates as a defogger;
activates ON at 70°F (21°C), OFF at 85°F (29°C)
Heater operates as a defroster;
activates ON at 40°F (4°C), OFF at 67°F (19°C)
GENERAL
Construction
Finish
Environment
Operating Range
Aluminum
Gray polyester powder coat
Indoor/outdoor
-50° to 122°F (-46° to 50°C)
Unit Weight
EH2508
EH2508-1/-2/-3
EH2512
EH2512-1/-2/-3
EH2515
EH2515-1/-2/-3
2.95 lb (1.34 kg)
3.10 lb (1.41 kg)
3.75 lb (1.70 kg)
3.90 lb (1.77 kg)
4.63 lb (2.10 kg)
4.83 lb (2.19 kg)
(Design and specifications are subject to change without notice.)
C1473M-D (9/08)
13
B
A
1.00
(2.54)
WINDOW
Ø 4.05
4.25
5.31
(10.80)
(10.29)
(13.49)
4.00
(10.16)
2.00 (5.08)
1.00 (2.54)
3X 1/4-20 X 0.625
1.00 (2.54)
2.00 (5.08)
A
B
EH2508
EH2512
EH2515
8.00 (20.32)
12.00 (30.48)
15.00 (38.10)
9.00 (22.86)
13.00 (33.02)
16.00 (40.64)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.
REVISION HISTORY
Manual #
C1473M
C1473M-A
Date
1/98
9/98
Comments
Original version.
Rev. A. Completely revised. Removed Section 2.2, Options. Revised wiring instructions to
clarify wiring with the same power input and wiring with different power input per ECO
98-3780. Revised Figure 5, EH2500 Series Wiring Diagram, per ECO 98-3879 to show more
descriptive labeling of individual functions. Removed
Section 3.4, Sun Shroud Installation and Section 7.0, Exploded Assembly Diagram. Created
Sun Shroud manual (C1474M) and Service/Maintenance manual (C1473SM).
Revised Figure 5 for new heater elements per ECO 00-6032. Removed Table A and
Troubleshooting section. Changed to new format.
7/00
C1473M-B
10/04
Revised camera and lens installation per ECO 04-9848. Product redesigned to fit CC3610/
CC3710/CC3770/MC3610/MC3710 Series cameras. Updated layout to new format.
Revised wiring connections and diagram per ECO 04-10623.
Added item 13 to Important Safety Instructions. Added Table A. Added warning about
mounting angle to Installation.
C1473M-C
C1473M-D
4/05
12/05
C1473M-E
9/08
Revised wiring diagrams to show rotated terminal block per CN21614.
14
C1473M-D (9/08)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
•
•
Five years on fiber optic products and TW3000 Series unshielded twisted pair (UTP) transmission products.
Three years on Spectra® IV products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry® Series hardware products, DVX Series
digital video recorders, NVR300 Series network video recorders, and Endura® Series distributed network-based video products.
Three years on Camclosure® and Pelco-branded fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
•
•
•
•
•
•
•
•
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit Ti and TI2500 Series thermal imaging products.
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
•
•
•
Two years on Intelli-M® eIDC controllers.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the
Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.
The materials used in the manufacture of this document and its components are compliant to the requirements
of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive
2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE).
Contact your local dealer for procedures for recycling this equipment.
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc.
© Copyright 2008, Pelco, Inc. All rights reserved.
DLP is a registered trademark of Texas Instruments Incorporated.
Lexan is a registered trademark of the General Electric Company.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: (800) 289-9100
Fax: (800) 289-9150
International
Tel: +1 (559) 292-1981
Fax: +1 (559) 348-1120
ISO9001
Australia Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
|