Pelco Landscape Lighting C2432M A User Manual

®
DF5HD Series  
Heavy-Duty  
Fixed-Mount  
Dome  
Installation Manual  
C2432M-A (12/03)  
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150  
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120  
 
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and  
it must not be installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by Pelco.  
4. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and  
lens combination.  
The product and/or manual may bear the following marks:  
This symbol indicates that dangerous voltage  
CAUTION:  
constituting a risk of electric shock is present  
within this unit.  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.  
DESCRIPTION  
The Heavy-duty DF5HD Series dome is perfect for fixed camera installations where structural integrity and vandalism are a priority.The  
system features barrel key locks, heavy-duty construction and a thick injection-molded plastic lower dome. The in-ceiling model has a  
reinforced bracket mounting system for installation in a fixed ceiling. Pendant models can be mounted to a pole or wall using the IWM  
wall mount.  
MODELS  
DF5HD-1  
DF5HD-PG-1  
DF5HD-PG-E1  
In-ceiling back box with reinforced bracket-mounting system and clear dome  
Indoor, pendant style back box with reinforced sun shroud and clear dome  
Environmental, pendant style back box with heater, fan, reinforced sun shroud and clear dome  
Pelco Installation Manual C2432M-A (12/03)  
3
 
INSTALLATION IN-CEILING MODEL  
PREPARE CEILING  
00530  
00532  
00531  
a. Locate the center point of the mount-  
ing location. Drill a hole in the ceiling  
using a 3/32-inch drill.  
b. Insert the compass tool into the hole.  
c. Use the mounting ring as a template  
and mark the hole pattern onto the  
mounting surface. Prepare the holes.  
Draw a circle on the ceiling using the  
compass tool and a pencil. Cut the  
circle out of the ceiling.  
INSTALL THE MOUNTING PLATES  
Use the eight 10-32 x 3-inch screws (supplied) and install the mounting ring and  
two back mounting plates.  
S
CEILING  
a. Line up the mounting ring with the  
eight fastener holes.  
c. Install fasteners through the mounting  
ring, ceiling, and out the back mount-  
ing plate.  
b. Feed one back mounting plate through  
the hole in the ceiling and line up with  
four fastener holes.  
d. Install second back mounting plate.  
MOUNTING  
RING  
00533  
INSTALL THE BACK BOX  
SPRING CLIP  
ATTACH SAFETY CHAIN HERE  
8-32 X .250-INCH SCREW  
00534  
01237  
a. Attach the conduit fitting, lock nut, and safety chain bracket.  
Install a safety chain/cable (not supplied) that will support up  
to 16 pounds (7.3 kg).  
c. Compress the spring clips on the back box and push it through  
the hole, until the clips spring back. Tighten the screws until  
you hear a clicking noise. Insert the two 8-32 x .250-inch  
screws to secure the back box to the mounting ring.  
b. Turn the thumbscrew and open the hinged door to the back  
box. Pull wiring into the back box through the conduit fitting.  
Refer to Tables A and B for cable requirements and wiring  
distances.  
4
Pelco Installation Manual C2432M-A (12/03)  
 
INSTALLATION PENDANT MODELS  
MOUNT AND INSTALL THE BACK BOX  
NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out.  
00540  
00541  
a. Install the mount for the pendant dome. Refer to the instruc-  
tions supplied with the mount. Bring the wiring for the dome  
through the mount. Refer to Tables A and B for cable require-  
ments and wiring distances.  
c. Screw the back box into the mount. If outdoors, apply thread  
compound (provided) to the threads on the back box.  
b. Pull wiring from the mount into the back box.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
RG11/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
Table B. 24 VAC Wiring Distances  
The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10-percent voltage drop.  
(Ten percent is generally the maximum allowable voltage drop for AC-powered devices.)  
EXAMPLE: An enclosure that requires 80 vA and is installed 35 feet (10 m) from  
the transformer would require a minimum wire gauge of 20 AWG.  
NOTE: Distances are calculated in feet; values in parentheses are meters.  
Wire Gauge  
20  
18  
16  
14  
12  
10  
10  
20  
30  
40  
50  
60  
70  
80  
283 (86)  
141 (42)  
94 (28)  
70 (21)  
56 (17)  
47 (14)  
40 (12)  
35 (10)  
451(137)  
225 (68)  
150 (45)  
112 (34)  
90 (27)  
75 (22)  
64 (19)  
56 (17)  
716 (218) 1142 (348) 1811 (551) 2880 (877)  
358 (109)  
238 (72)  
179 (54)  
143 (43)  
119 (36)  
102 (31)  
89 (27)  
571 (174)  
380 (115)  
285 (86)  
228 (69)  
190 (57)  
163 (49)  
142 (43)  
905 (275) 1440 (438)  
603 (183)  
452 (137)  
362 (110)  
301 (91)  
258 (78)  
226 (68)  
960 (292)  
720 (219)  
576 (175)  
480 (146)  
411 (125)  
360 (109)  
Pelco Installation Manual C2432M-A (12/03)  
5
 
CAMERA AND LENS INSTALLATION  
To install the camera and lens:  
1. Extend the lens to the maximum length before installing in the back box.  
2. Attach the camera to the tilt table with the 1/4-20 screw and washers (supplied).  
3. To ensure that the lens will not hit the lower dome:  
Place the lower dome over the back box with the camera and lens installed (do not attach dome).  
If the lens touches the lower dome, adjust the tilt table assembly.  
4. Refer to the manual supplied with the camera and lens for the following information:  
How to connect power and video wiring  
How to make camera and lens adjustments  
NOTE: The torque applied to the camera mounting bracket nut should not exceed 40 pound-inches.  
LOWER DOME INSTALLATION  
IN-CEILING MODEL  
a. Attach the lower dome trim leash to one of the 8-32 x .250-inch  
screws that secure the back box to the mounting ring.  
BALL STUD  
BALL STUD  
RECEIVER  
b. Insert both keys in the barrel locks. Turn keys clockwise to the un-  
TRIM LEASH  
locked position. Keys can not be removed from lock in the unlocked  
position.  
c. Align pegs (located on the mounting ring) with the peg receptacles  
(located on the inside of the lower dome).  
BARREL  
KEY LOCK  
d. Place lower dome over back box. Hold and turn both keys to the  
00495  
locked position.  
PENDANT MODELS  
HEATER  
CONNECTORS  
BARREL  
LOCK  
TRIM  
LEASH  
O-RING  
CENTER  
PIN  
00543  
00494  
a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in  
the groove on the trim ring of the lower dome.  
b. Align barrel locks in lower dome with the holes located on  
each side of the back box. Push lower dome onto back box.  
Press the pins of the barrel locks IN to secure the  
lower dome.  
Attach the back box trim leash to a retainer screw inside the  
lower dome.  
Environmental Model only: Plug the two-pin heater  
connection in the lower dome into the mating connector in the  
back box.  
6
Pelco Installation Manual C2432M-A (12/03)  
 
SPECIFICATIONS  
ELECTRICAL  
Input Voltage:  
Input Power:  
24 VAC (outdoor models only)  
62 vA (for heater)  
MECHANICAL  
Construction  
Back Box:  
Aluminum  
Mounting Bracket:  
Lower Dome:  
Dimensions:  
Steel  
Clear polycarbonate, 0.090 inch thick  
See dimension drawing  
GENERAL  
Environment  
In-Ceiling:  
Indoor only  
Pendant:  
Indoor/outdoor, NEMA 4X, IP66 Rated  
Operating Range  
In-Ceiling:  
32 to 140°F (0 to 60°C) intermittent operation; 32 to 122°F (0 to 50°C) continuous operation  
Pendant  
Without Heater:  
32 to 140°F (0 to 60°C) absolute maximum operating temperature;  
32 to 122°F (0 to 50°C) sustained maximum operating temperature  
(Assumes no wind chill factor; for detailed test conditions, contact Pelco.)  
With Heater:  
Maximum operating  
temperature:  
140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum  
Minimum operating  
temperature:  
-60°F (-51.11°C) absolute minimum; minimal icing at -50°F (-45.56°C) sustained minimum;  
prevents icing at -40°F (-40°C) sustained minimum; de-ices. 1 inch (2.5 mm) within 3 hours after power-up  
Weight  
Back Box  
Unit  
(without camera)  
In-ceiling:  
Pendant Indoor:  
Outdoor Pendant:  
Lower Dome  
In-ceiling:  
2.17 lb (.98 kg)  
4.45 lb (2.02 kg)  
4.75 lb (2.15 kg)  
1.6 lb (.73 kg)  
1.83 lb (.83 kg)  
Pendant:  
CAMERA  
Maximum Camera and  
Lens Size:  
5.00 (L) x 2.75 (W) x 2.75 (H) (12.70 x 6.99 x 6.99 cm)  
(Design and product specifications subject to change without notice.)  
DUAL WALL  
CONSTRUCTION  
10.1  
(25.65)  
7.5  
(19.05)  
fl 6.13  
fl15.57)  
9.70  
(24.64)  
(
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;  
ALL OTHERS ARE INCHES  
Pelco Installation Manual C2432M-A (12/03)  
7
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
Loctite is a registered trademark of Loctite Corporation.  
©Copyright 2003, Pelco. All rights reserved.  
REVISION HISTORY  
Manual # Date Comments  
C2432M  
7/01  
Original version.  
C2432M-A 12/03 Per ECO #03-9442, changed dome material description from acrylic to clear polycarbonate.  
8
Pelco Installation Manual C2432M-A (12/03)  
 

Peavey Guitar TL Five User Manual
Philips Telephone VOIP1511 User Manual
Philips TV Receiver 29PT5435 User Manual
Philips TV Receiver DCR9000 User Manual
Pioneer Home Theater System CTL7 User Manual
Pioneer Industrial DVD Player DV 470 User Manual
Poulan Chainsaw 2550T User Manual
ProForm Home Gym PFMC77754 User Manual
ProForm Treadmill 831297390 User Manual
PYLE Audio Car Amplifier PQA3100 User Manual