Pelco Blower BK3512 2 User Manual

I N S T A L L A T I O N  
BK3512 Series  
Blower Kit  
C1436M-G (2/06)  
 
Description  
You can install the BK3512 Series blower kit only in enclosures in the EH3512 Series, EH3515 Series,  
and EH3515L Legacy® Series.  
MODELS  
BK3512-1  
BK3512-2  
BK3512-3  
Blower kit, continuous duty, 120 VAC, 4 watts  
Blower kit, continuous duty, 24 VAC, 2 watts  
Blower kit, continuous duty, 230 VAC, 9 watts  
Installation  
The following items are supplied:  
1
2
Blower  
Screws  
BK3512-1, -3  
BK3512-2  
6-32 x 1-1/2-inch Phillips, pan head  
6-32 x 1-3/8-inch Phillips, pan head  
2
Internal star lock washers  
Perform the following steps to install the BK3512 blower kit:  
1. Disconnect all sources of power from the enclosure.  
2. Unlatch and open the lid.  
3. If necessary, remove the camera and camera sled.  
a. Disconnect the power and video from the camera.  
b. Loosen the screws that hold the camera sled in place.  
c.  
Slide the sled forward so it can be lifted out over the screws. Do not lift the sled out yet.  
d. Retighten the screws so the sliding bar under the sled lip will not move. This will assure  
that you reinstall the camera and sled in the same place.  
e. Remove the camera and sled.  
4. Do one of the following:  
If you have an EH3515 Series enclosure with a heater and defroster installed, do the  
following:  
a. Remove the screws attaching the rear heater bracket to the enclosure.  
b. Place the blower against the rear heater bracket, and attach using the screws and  
lock washers provided (refer to Figure 1). Be sure the arrow on the blower housing  
is pointing toward the viewing window.  
Place the blower against the rear of the enclosure, and attach using the screws and lock  
washers provided (refer to Figure 2). Be sure the arrow on the blower housing is  
pointing toward the viewing window.  
C1436M-G (2/06)  
3
 
5. Connect the blower wires directly to power or, if there is a heater and defroster installed, you  
will need to connect the blower wires to the PC board. To remove the PC board cover, insert a  
screwdriver into the slot on top of the cover and lift the cover off.  
Connect the blower wires to the PC board (refer to Figure 3). If required, connect ground to the  
stud on the bottom of the enclosure just in front of the PC board.  
Replace the PC board cover, making sure it snaps securely back into place. Be sure the blower  
wires are not obstructing other accessories in the enclosure. If you are installing the  
BK 3512-2 blower kit (24 VAC), refer to Table A.  
6. If you removed the camera and camera sled, reinstall them.  
7. Close the enclosure lid, and latch.  
8. Reconnect power to the enclosure.  
REAR  
LOCK  
HEATER  
BRACKET  
WASHER  
SCREW  
PC BOARD  
COVER  
SCREW  
FRONT  
HEATER  
BRACKET  
LOCK WASHER  
HEATER  
NYLON  
WASHER  
BLOWER  
PC BOARD  
HEATER  
DEFROSTER  
Figure 1. Blower Kit Installation in Enclosure with Rear Heater  
4
C1436M-G (2/06)  
 
 
BLOWER  
Figure 2. Blower Kit Installation in Enclosure without Rear Heater  
120 VAC MODEL  
24 VAC MODEL  
INPUT, AC HIGH  
INPUT, AC HIGH  
INPUT, AC LOW (NEUTRAL)  
INPUT, AC LOW (NEUTRAL)  
1
2
3
4
5
1
2
3
4
5
RED  
BLK  
RED  
BLOWER  
BLK  
DIODE  
BRIDGE  
BLOWER  
6
7
6
7
CAP  
8
8
9
10  
9
10  
230 VAC MODEL  
NOTE: THE DEFROSTER ALSO  
IS CONNECTED TO  
TERMINALS 4 AND 5.  
INPUT, AC HIGH  
INPUT, AC LOW (NEUTRAL)  
1
2
3
4
5
6
7
120 VAC BLOWER  
RESISTOR  
8
9
10  
Figure 3. Wiring Diagrams for PC Board  
C1436M-G (2/06)  
5
 
   
Table A. 24 VAC Wiring Distances  
The following are the recommended maximum distances for 24 VAC applications and are calculated with  
a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for  
AC-powered devices.  
Wire Gauge  
20  
18  
16  
14  
12  
10  
283 (86)  
451 (137) 716 (218) 1142 (348) 1811 (551) 2880 (877)  
10  
20  
30  
40  
50  
141 (42)  
94 (28)  
70 (21)  
56 (17)  
225 (68)  
150 (45)  
112 (34)  
90 (27)  
358 (109) 571 (174) 905 (275) 1440 (438)  
238 (72)  
179 (54)  
143 (43)  
380 (115) 603 (183) 960 (292)  
285 (86)  
228 (69)  
452 (137) 720 (219)  
362 (110) 576 (175)  
Example: An enclosure that requires 30 VA and is installed 94 feet (28 m) from the transformer  
would require a minimum wire gauge of 20 AWG.  
NOTE: Distances are calculated in feet; values in parentheses are meters.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
6
C1436M-G (2/06)  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models, which have a five-year warranty.  
Three years on PMCL 200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of  
90 days. The air filter is not covered under warranty.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, EnduraSeries distributed network-based video  
products, and TW3000 Series twisted pair transmission products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight  
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this  
warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization  
number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
REVISION HISTORY  
Manual #  
C1436M-G  
Date Comments  
2/06 Revised to new format. Added cover photo. Updated per ECO 04-10624, which added PCB cover and  
ground stud.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2006, Pelco.  
All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
 
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East  
|
|
|
|
|
|
|
|
 

Philips CRT Television 14PT1363 User Manual
Philips CRT Television 14PT2694 User Manual
Philips PDAs Smartphones SBC RU 220 00 User Manual
Philips Projection Television 64P8341 User Manual
Philips TV VCR Combo 14PV360 07 User Manual
Phonetics Network Card SCADA 3000 User Manual
Pinnacle Design TV Video Accessories TV24203 User Manual
Polycom Recording Equipment 2000 User Manual
Poulan Lawn Mower PRGT22H50C User Manual
PYLE Audio Flat Panel Television PLD3MU User Manual