®
MR3050
Universal Monitor Mount
Installation/Operation Manual
C222M-A (8/95)
Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827 • DataFax (800) 289-9108 or (1-559) 292-0435
International customers call (1-559) 292-1981 or FAX (1-559) 348-1120
INSTALLATION/OPERATION MANUAL
MR3050
UNIVERSAL MONITOR MOUNT
1.0 WARNINGS
2.0 SCOPE
Priortoinstallationanduseofthisproduct,thefollowing
WARNINGS should be observed.
The information contained within this manual covers
the MR3050 Universal Monitor Mount.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
3.0 DESCRIPTION
The MR3050 is a universal monitor mount engineered
to safely mount a monitor from either a ceiling or a
wall. This mount was designed for use in security
systems, educational institutions, churches, hospitals,
and other applications requiring flexibility in monitor
mounting and positioning.
2. Installation shall be done in accordance with all
local and national electrical and mechanical codes
utilizing only approved materials.
3. Use only installation methods and materials ca-
pable of supporting four (4) times the maximum
specified load.
The MR3050 is an adjustable mount designed for use
with 14-19" (35.56-48.26 cm) monitors. Two optional
adapters are available for this mount: the MRWA for
wall mounting and the MRCA for ceiling mounting.
An8"(20.32cm)lengthof1-1/2"NPTpipeisprovided
with the mount.
4. Use stainless steel hardware to fasten the mount to
outdoor surfaces.
5. To prevent damage from water leakage when in-
stalling a mount outdoors on a roof or wall, apply
sealant around the bolt holes between the mount
and mounting surface.
3.1 RECOMMENDED MOUNTS
MRWA
Wall mount, uses six (6), 5/16" diameter
fasteners (not supplied)
Please thoroughly familiarize yourself with the infor-
mation in this manual prior to installation and opera-
tion.
MRCA
Ceiling mount, uses four (4), 5/16" diam-
eter fasteners (not supplied)
PELCO Manual C222M-A (8/95)
1
4.0 SPECIFICATIONS
Maximum Load: 65 lbs (29.45 kg)
Tilt Angle:
Construction:
Finish:
Adjustable ±45°
Dimensions:
Weight:
See Figure 1
Steel
17.08 lbs (7.74 kg)
Poly vinyl powder coat
Shipping Weight: 20 lbs (9.06 kg)
Figure 1. MR3050 Dimension Drawing
2
PELCO Manual C222M-A (8/95)
5.0 INSTALLATION
3. Thread the 8" (20.32 cm) pipe supplied into the
ceiling/wall adapter which has already been in-
stalled.
5.1 MRCA/MRWA ADAPTER MOUNTING
1. Determine the mounting location. Remember to
allow for adequate clearance on all sides of the
monitor.
4. Thread collar with cross bar attached onto the end
of the 8" (20.32 cm) pipe attached to the ceiling/
wall mount (already installed).
NOTE: When determining the mounting lo-
cation, consideration must be given to the total
weight of the monitor and the mount. The
mounting surface must be adequate to support
this weight.
5. Slide the side brackets (item 2, Figure 2) onto cross
bar and thread on the 1/4-20 bolts. Don't tighten
bolts until all pieces are together.
6. Lift monitor with base pieces attached up to mount.
Attach side brackets to base pieces on monitor us-
ing the four (4) 3/8-16 bolts supplied.
2. Use the adapter mount as a template to mark the
required mounting holes.
7. Tighten set screws in upper part of collar to lock
mount and collar in place.
3. Using the necessary fasteners, attach the adapter
mount to the chosen surface.
8. Tilt the monitor to the desired angle and tighten
bolts on each side of adjusting brackets.
5.2 MR3050 INSTALLATION
1. Determine the width the base mounting brackets
(item 1, Figure 2) must be positioned to in order to
accommodate the monitor being used. Next, attach
the two (2) bracket supports (item 13, Figure 2) to
the base mounting brackets as indicated in Figure
2.
9. Make all necessary electrical connections.
2. Attach the monitor to the base mounting brackets.
If the monitor has removable rubber feet, remove
the screws from the monitor feet and remove the
feet. Use the same hardware to attach the monitor
to the base mounting brackets.
PELCO Manual C222M-A (8/95)
3
6.0 EXPLODED ASSEMBLY
An exploded assembly diagram for the MR3050 is shown in Figure 2.
Figure 2. MR3050 Exploded Assembly Diagram
4
PELCO Manual C222M-A (8/95)
7.0 MECHANICAL PARTS LIST
Item No.
Qty
2
Description
Part Number
MR30504001COMP
MR30504003COMP
MR30504000COMP
1
2
3
Base, upright
Adj., side bracket
Cross bar
2
1
4
1
Collar
MR30004103COMP
5
6
1
2
6
6
1
4
4
1
2
1
1/2-13 Bolt, 1.00 long
Set screw 1/4-20
Hex head 1/4-20
ZH1/213X1.00CH
ZH1/420X.250S
7
ZH1/4-20X.500CH
ZH260X562X65C
MR30504104COMP
ZH3/816X.500SH
ZH377X880X78
8
Washer, flat
9
Washer, flat
10
11
12
13
14
Bolt 3/8-16 hex head
Washer, flat
Pipe nipple, 8" L x 1-1/2" NPT (not shown)
Bracket, support
MRU4207COMP
MR30504002COMP
ZH1/213NUTCHN
Nylock nut
NOTE: Items 3, 4, 5, 9 and 14 are shipped factory assembled.
PELCO Manual C222M-A (8/95)
5
8.0 WARRANTY AND RETURN
INFORMATION
If a warranty repair is required, the Dealer must con-
tact Pelco at (800) 289-9100 or (559) 292-1981 to ob-
tain a Repair Authorization number (RA), and provide
the following information:
WARRANTY
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order num-
ber, or Pelco invoice number
Pelco will repair or replace, without charge, any mer-
chandise proved defective in material or workmanship
for a period of one (1) year after the date of shipment.
Exceptions to this warranty are as noted below:
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions stated
above, please include a written explanation with the
product when returned.
•
•
Two (2) years on all standard motorized and fixed
focal length lenses.
Two (2) years on Legacy®, Intercept®, CM8500/
CM9500/CM9750 Matrix, Spectra™, DF5 Series
and DF8 Fixed Dome products.
Ship freight prepaid to: Pelco
300 West Pontiac Way
•
Two (2) years on WW5700 series window wiper
(excluding wiper blades).
Two (2) years on cameras.
Six (6) months on all pan and tilts, scanners or pre-
set lenses used in continuous motion applications
(e.g., preset scan, tour and auto scan modes).
Clovis, CA 93612-5699
•
•
Method of return shipment shall be the same or equal
to the method by which the item was received by Pelco.
RETURNS
Pelco will warranty all replacement parts and repairs
for 90 days from the date of Pelco shipment. All goods
requiring warranty repair shall be sent freight prepaid
to Pelco, Clovis, California. Repairs made necessary
by reason of misuse, alteration, normal wear, or acci-
dent are not covered under this warranty.
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or (559) 292-1981 to obtain an authorization num-
ber (CA number if returned for credit, and RA number
if returned for repair). Goods returned for repair or credit
should be clearly identified with the assigned CA/RA
number and freight should be prepaid. All merchan-
dise returned for credit may be subject to a 20% re-
stocking and refurbishing charge.
Pelco assumes no risk and shall be subject to no liabil-
ity for damages or loss resulting from the specific use
or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, neg-
ligence, infringement of any rights of any party or prod-
uct liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products.
In no event will Pelco be liable for any special, inci-
dental or consequential damages (including loss of use,
loss of profit and claims of third parties) however
caused, whether by the negligence of Pelco or other-
wise.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
The above warranty provides the Dealer with specific
legal rights. The Dealer may also have additional rights,
which are subject to variation from state to state.
6
PELCO Manual C222M-A (8/95)
|