Peerless Industries TV Mount DS VW660 User Manual

Installation and Assembly:  
Video Wall Mount  
Model: DS-VW660  
Maximum Load Capacity: 200 Ib ( 90 kg)  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
1 of 10  
 
Vertical Spacing Location  
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing.  
To determine lower mounting slot position of second mount, add display height to (Y1) or (Y2)  
1
DISPLAY  
HEIGHT  
10.25  
1.688  
X
Y2  
Y1  
.938  
Vertical Location  
X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2)  
Horizontal Spacing Location  
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing.  
To determine edge of second mount, add (Z) to edge of first mount.  
DISPLAY WIDTH  
16.00"  
20.00"  
24.00"  
Z
17.50"  
Horizontal Location  
DISPLAY WIDTH - (35) = Z (SPACING BETWEEN MOUNTS)  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
3 of 10  
 
PARTS LIST  
Description  
Qty.  
1
1
2
1
4
4
4
2
4
4
3
1
Part #  
145-1160  
145-1145  
145-1158  
145-1154  
5S1-015-C03  
590-0320  
590-2233  
510-1126  
520-1128  
520-9257  
520-1023  
560-9646  
A carriage assembly  
B wall plate  
C adapter bracket  
D lock bracket  
E #14 x 2.5 hex head wood screw  
F concrete anchor  
G .38 OD x .06 LG nylon shoulder washer  
H M5 x 10 mm socket pin serrated washer head screw  
I
M6 x 12 mm phillips screw  
J M8 x 16 mm phillips screw  
K M5 x 6 mm phillips screw  
L 4 mm allen wrench  
A
B
C
D
I
E
F
G
H
J
K
L
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
4 of 10  
 
Installation to Wall Stud  
WARNING  
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all  
attached hardware and components.  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder  
is highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.  
Installers are responsible to provide hardware for other types of mounting situations.  
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.  
Based on their edges, draw a vertical line down the stud center. Place wall plate (B) on wall as a template. Level  
plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud center  
line. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate (B) is level, secure it  
using four #14 x 2.5" wood screws (E) as shown below.  
1
STUD  
B
E
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
5 of 10  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual  
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount  
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM  
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a  
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware  
and components.  
solid concrete  
Make sure that video wall plate (B) is level, use it  
1
as a template to mark four mounting holes. Drill four  
F
cinder block  
5/16” (8 mm) dia. holes to a minimum depth of 2.5”  
(64 mm). Insert anchors (F) in holes flush with wall  
as shown (right). Place video wall mount assembly  
over anchors and secure with four #14 x 2.5” screws  
(E). Level, then tighten all fasteners.  
WARNING  
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
B
E
• Never tighten in excess of 80 in. • lb (9 N.M.).  
concrete  
surface  
• Always attach concrete expansion anchors directly  
to load-bearing concrete.  
1
• Never attach concrete expansion anchors to  
concrete covered with plaster, drywall, or other  
finishing material. If mounting to concrete surfaces  
covered with a finishing surface is unavoidable,  
the finishing surface must be counterbored as  
shown below. Be sure concrete anchors do not  
pull away from concrete when tightening screws. If  
plaster/drywall is thicker than 5/8" (16 mm), custom  
fasteners must be supplied by installer  
F
Drill holes and insert anchors (F).  
B
2
E
F
Place wall plate (B) over anchors (F) and secure with screws (E).  
INCORRECT  
CORRECT  
3
concrete  
concrete  
wall  
plate  
wall  
plate  
plaster/  
drywall  
plaster/  
drywall  
Tighten all fasteners.  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
6 of 10  
 
Attaching Adapter Brackets to Display  
Attach adapter brackets (C) to back of display using four M6 x 12 mm phillips screws (I) with nylon shoulder washer (G), or four  
M8 x 15 mm phillips screws (J) as shown below.  
NOTE: Hardware to attach dedicated plates to the mount are included with the dedicated plates.  
2
DISPLAY  
I or J  
G
MAX VESA-600 mm  
MIN VESA-200 mm  
C
400 mm  
300 mm  
200 mm  
PLP  
Attach adapter brackets (C) and display onto channels on carriage assembly (A) as shown in figure 3.1.  
Secure adapter brackets (C) using lock bracket (D) with three M5 x 6 mm phillips screws (K) as shown in figure 3.2.  
3
CHANNEL  
DISPLAY  
A
D
C
K
A
DISPLAY  
BACK VIEW  
FIGURE 3.1  
FIGURE 3.2  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
7 of 10  
 
Horizontal Display Position  
Screen and adapter brackets can slide along rail to position  
.
screen horizontally  
OF  
OUTSIDE EDGE  
OPTIONAL GUIDE: When positioning adapter brackets (C) make sure outside  
edge of adapter bracket is in notch on display carriage as shown in detail 1.  
ADAPTER BRACKET  
600 mm  
400 mm  
NOTCH  
300 mm  
200 mm  
C
PLP  
FRONT  
DETAIL 1  
Installing Carriage Assembly to Wall Plate  
Hook Carriage Assembly (A) slot onto pins on wall plate (B). Make sure that pins fully engage slot of carriage assembly (A) as  
4
shown in detail 2.  
SLOT  
PIN  
A
B
DISPLAY  
SLOT  
DETAIL 2  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
8 of 10  
 
Secure Carriage Assembly (A) to wall plate (B) with two M5 x 10 mm socket pin serrated washer head screws (H) using  
4 mm allen wrench (L) as shown below.  
5
B
H
A
Horizontal Display Adjustment  
Adapter Brackets (C) and display can be adjusted horizontally.  
6
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
9 of 10  
 
Carriage Assembly Adjustment  
Use legend below to determine position of display.  
NOTE: Each knob can be adjusted independently for fine tuning adjustments.  
7
Turn knob CLOCKWISE to tighten  
Turn knob COUNTER-CLOCKWISE to loosen  
UP  
DOWN  
ROLL RIGHT  
ROLL LEFT  
ISSUED: 01-05-10 SHEET #: 125-9128-1 06-28-10  
10 of 10  
© 2010, Peerless Industries, Inc. All rights reserved.  
All other brand and product names are trademarks or  
registered trademarks of their respective owners.  
 

Philips Cassette Player AQ6485 00Z User Manual
Philips Cell Phone SE171 User Manual
Philips Scanner 42PFL6805H User Manual
Philips Telephone SJA9190 17 User Manual
Pinnacle Design TV Video Accessories TV66607 User Manual
Pioneer Stereo Receiver VSX AX10Ai G User Manual
Planet Technology Network Card PL 103E User Manual
Polycom Webcam 75 User Manual
Poulan Lawn Mower PR185H42STG User Manual
Proctor Silex Microwave Oven Microwave Oven 87025 User Manual