Peerless Industries TV Mount DS VL H024 User Manual

Installation and Assembly:  
24" Wall Plate Accessory  
Model: DS-VL-H024  
Maximum Load Capacity: 350 lb (158.8 kg)  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 06-04-10 SHEET #: 120-9084-1  
 
Before you begin, make sure all parts shown are included with your product.  
PARTS LIST  
A
Description  
Qty.  
1
8
4
2
Part #  
145-1140  
510-1079  
590-0320  
024-1045  
560-1727  
5S1-015-C03  
A wall plate  
B M4 x 12 mm socket pin serrated washer head screw  
C 8 mm concrete anchor  
D wall plate connector  
E 18" 4 mm allen wrench  
F # 14 x 2.5 hex head wood screw  
1
4
Some parts may appear slightly different than illustrated.  
B
C
D
E
F
Installing Additional Wall Plates (optional)  
When installing additional wall plates (sold separately) , attach two wall plate connectors (D) on either end of wall  
plate (A) and fasten with eight M4 x 12 serrated washer head socket pin screws (B) as shown below.  
1
Skip to step 2 on page 5 for  
installation to solid concrete or  
cinder block walls.  
B
D
A
BACK VIEW  
ISSUED: 06-04-10 SHEET #: 120-9084-1  
3 of 6  
 
Installation to Double Wood Stud Wall  
WARNING  
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all  
attached hardware and components.  
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the  
screws, greatly reducing their holding power.  
• Never tighten in excess of 80 in. • lb (9 N.M.).  
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder  
is highly recommended.  
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-  
ers are responsible to provide hardware for other types of mounting situations.  
Wall plate (A) can be mounted to four studs that are 16" apart. Use a stud finder to locate the edges of the studs.  
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each  
stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the four mounting holes.  
Make sure that the mounting holes are on the stud center lines. Drill four 5/32" (4 mm) dia. holes 2.5" (65 mm)  
deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (F) as shown in figure 2.2.  
2
STUD  
A
fig. 2.1  
A
F
fig. 2.2  
ISSUED: 06-04-10 SHEET #: 120-9084-1  
4 of 6  
 
Installation to Solid Concrete or Cinder Block  
WARNING  
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete  
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid  
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-  
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to  
avoid breaking out the back of the hole when entering a void or cavity.  
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.  
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-  
ware and components.  
Make sure that wall plate (A) is level, use it as a  
2
template to mark four mounting holes. Drill four  
5/16" (8 mm) dia. holes to a minimum depth of 2.5"  
(64 mm). Insert anchors (C) in holes flush with wall  
as shown (right). Place wall plate over anchors and  
secure with #14 x 2.5" screws (F). Level, then tighten  
all fasteners.  
concrete  
surface  
1
C
Drill holes and insert anchors (C).  
A
2
WARNING  
• Tighten screws so that wall plate is firmly attached,  
but do not overtighten. Overtightening can damage  
screws, greatly reducing their holding power.  
F
C
Place plate (A) over anchors (C) and secure with screws (F).  
3
• Never tighten in excess of 80 in. • lb (9 N.M.).  
WARNING  
• Always attach concrete anchors directly to load-  
bearing concrete.  
Tighten all fasteners.  
• Never attach concrete anchors to concrete covered  
with plaster, drywall, or other finishing material.  
If mounting to concrete surfaces covered with  
a finishing surface is unavoidable, the finishing  
surface must be counterbored as shown below.  
Be sure concrete anchors do not pull away from  
concrete when tightening screws. If plaster/drywall  
is thicker than 5/8", custom fasteners must be  
supplied by installer.  
solid concrete  
cinder block  
C
INCORRECT  
CORRECT  
concrete  
concrete  
wall  
plate  
wall  
plate  
plaster/  
drywall  
plaster/  
drywall  
A
F
ISSUED: 06-04-10 SHEET #: 120-9084-1  
5 of 6  
 
Installing Multiple Wall Plates and Screens (Optional)  
Install adapter brackets (sold separately) to screens using adapter bracket instructions.  
Multiple wall plates and adapter brackets (sold separately) can be used to create multiple screen displays.  
3
WALL PLATE MAY APPEAR  
DIFFERENT THAN ILLUSTRATED  
ACC-DSV240  
(SOLD SEPARATELY)  
ISSUED: 06-04-10 SHEET #: 120-9084-1  
6 of 6  
© 2010, Peerless Industries, Inc. All rights reserved.  
All other brand and product names are trademarks or registered trademarks of their respective owners.  
 

Phase Technology Speaker RS4 EZ User Manual
Philips Car Video System 244EI User Manual
Philips Electric Toothbrush HX1510 User Manual
Philips Home Theater System FR970 User Manual
Philips MP3 Docking Station DCM230 User Manual
Philips Portable DVD Player PET742 93 User Manual
Polaroid Digital Camera i639 User Manual
Poulan Tiller 96092001501 User Manual
Powermate Portable Generator PC052530019 User Manual
PYLE Audio Car Stereo System AT 3040 User Manual