FAQs
Applications
What is the primary application for the Model 1058, 12.5 Mbps VDSL Ethernet Extender?
LAN Extension & Service Integration
Used in pairs, the Model 1058 establishes a high-speed, line sharing, symmetrical 12.5 Mbps voice and data
link. The Model 1058 inter-connects two geographically separated LANs over a voice-grade twisted pair
wire. Operation is simple: packets destined for the remote LAN are sent transparently, at full line rate, to the
peered LAN. The Model 1058DV's built-in POTS/ISDN splitter allows users to simultaneously talk on the
phone while surfing the WWW, downloading files, or receiving emails.
Other Applications include:
•
•
•
•
MTU/MDU Internet Services
Network Backbones
Remote Workstations and Equipment
ISP Last Mile Extension
1
FAQs
Does the Model 1058 operate in pairs?
Yes, the Model 1058 must operate in pairs. For each link, a Central Office (1058DV/CO/E) and Customer
Premise (1058DV/CP/E) unit is required. For concentrated applications, the 1058DVRC/CP and
1058DV/CP/E standalone can be used to operate with the VDSL Concentrator (Model 3324).
Which end of the link should the “CO” Central Office unit and “CP” Customer Premise unit
be located?
The Model 1058DV/CO and 1058DV/CP should be located according to their descriptions. The 1058DV/CO
unit should to be placed at the Central Location and the 1058DV/CP should be placed at the Customer
Premise (Remote) due to special filtering requirements for each application.
Does the Patton Model 1058 support VLAN?
The Model 1058 will support VLAN (802.1Q) by passing the larger sized packets transparently. The Model
1058 does not have configuration commands to add a VLAN tag to a packet.
Does the Patton Model 1058 pass higher layer protocol such as TCP/IP packets?
Yes, the Model 1058 does pass higher layer protocols such as TCP/IP. The Model 1058 does not read the
TCP/IP packets, but will pass the packets on transparently.
Is the Model 1058 capable of bridging?
Yes, the Model 1058 will automatically learn, age, and filter 32 source addresses. Destination addresses of
incoming frames are compared with the Source Address in the address table and discarded if an entry
exists; otherwise, they are forwarded over the VDSL link.
Can voice and data be used simultaneously?
Yes, voice and data can be used simultaneously.
Will the POTS/ISDN port on the Model 1058DV operate without power?
The built-in POTS/ISDN Splitter is a passive element and does not require power to operate. The
POTS/ISDN port is able to provide a “life-line” telephone link provided the physical connection between the
CO and CP VDSL modems is still intact.
3
FAQs
Ethernet (10 or 100Base-T) Interface
What devices typically connect to the Ethernet 10/100Base-TX port?
Devices that typically connect to the Ethernet port are Ethernet Hubs/Switches, Remote PC’s, and any other
network enabled device.
How is the Ethernet port configured to accept 10 or 100Base-TX?
The Ethernet port automatically senses 10 or 100Base-TX Ethernet connections.
Does the Ethernet port require configuration for full or half-duplex connections?
The Model 1058 will automatically sense full or half-duplex Ethernet connections. To fully utilize the
100Base-TX Full-Duplex feature, your network enabled devices must support 802.3x flow control (pause
packets). A switch setting is provided on the Model 1058 to transparently lock out the 100Base-TX full
duplex communication if your network enabled devices do not support 802.3x flow control (pause packets).
This feature will only allow Ethernet connections in 10Base-T full/half duplex or 100Base-TX half duplex and
transparently avoid the 802.3x issue without degrading link performance.
Do I use straight-through or crossover cables?
The 1058 is equipped with an MDI-X switch that enables automatic connections to a hub (DCE) or PC (DTE)
interface, thereby eliminating confusion over whether a straight-through or crossover cable is needed. The
Ethernet port will automatically sense the required connection type.
Power Supply
What are the power supply options for the Model 1058’s?
The Model 1058’s come standard with an external 120VAC or UI (100-240VAC) power supply. –48, -24, or
-12VDC power supplies are optional and ordered separately.
4
|