PLD70BT
OWNER'S MANUAL
Mobile Video System
Motorized Slide Down and Detachable Panel
7 Inch Wide Color Touch Screen TFT
Car DVD/MP4/VCD/CD/MP3 Player
Front panel USB port and AUX input
Built in AM/FM Tuner and RDS
Bluetooth A2DP & AVRCP
SD Card Slot in the panel
Precautions
THANK YOU FOR PURCHASING THIS CAR DVD PLAYER .
Before operating the unit, read this manual thoroughly and keep it handy
for future reference .
To avoid injury or accident , read the following precautions before
installing and operating the unit .
ON INSTALLATION
DO NOT install any receiver in locations where;
- it may obstruct the steering wheel and gearshift lever operations, as this
may result in a traffic accident.
- it may obstruct the operation of safety devices such as air bags, as this
may result in a fatal accident.
- it may obstruct visibility.
DO NOT operate any receiver while manipulating the steering wheel, as
this may result in a traffic accident.
The driver must not watch the monitor while driving.
IF THE DRIVER watches the monitor while driving, it may lead to
carelessness and cause an accident.
IF YOU NEED to operate the receive while driving, be sure to look ahead
carefully or you may be involved in a traffic accident.
IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the
monitor, and no playback picture will be shown.
- This warning appears only when the parking brake wire is connected to
the parking brake system built in the car ( refer to the electric connection)
ABOUT THE LIQUID CRYSTAL DISPLAY (LCD) PANEL
Do not press on the LCD panel on the unit as doing so can distort the
picture or cause a malfunction . The picture may become unclear , or the
LCD panel may be damaged .
NOTES ON CLEANING
-Clean the LCD panel with a slightly damp soft cloth.
-Do not use solvents such as benzine, thinner, commercially available
cleaners or antistatic spray .
-Do not use alcohol to clean the screen .
If your car was parked in a cold or hot place, the picture may not be clear .
The monitor is not damaged . The picture will become clear the temper-
ature in your car becomes normal .
-2-
Safety Information
CAUTION:
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD
PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DVD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
COPYRIGHT PROTECTION
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this
DVD Player, this DVD Player cannot play this disc.
-3-
Disc Notes
Disc formats supported by this
player
unusable) depending on your handle it
and conditions in the usage environment.
Note these scratches are not an
Audio and Video
Disc size 12 cm
DVD
indication of any problem with the player.
Label side
up
Audio and Video
Disc size 12 cm
VCD
Audio
CD
Disc size 12 cm
Do not touch
the
underside
of the disc
Audio
MP3
Disc size 12 cm
Do not
bend
Discs which cannot be played
with this player
DVD-RAM
CDV
Wipe the disc from
center
toward the outside
edge
CDG
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Preparing New Discs with Rough
Spots
A new disc may have rough edges on
its inside and outside edges. If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc. Therefore,
remove the rough edges in advance
by using a ball point pen or pencil as
shown on the right. To remove the
rough edges, press the side of the pen
or pencil against the inside and outside
edges of the disc.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Rough spots
on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Ball point pen
or pencil
Rough spots
on inside
edge
Note:
A disc may become somewhat scratched
(although not enough to make it
-4-
Installation
NOTES:
1. Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
2. Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
3. Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
4. Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
5. Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
6. Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
7. If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
Revoving the unit
1. Press the REL button to release the front panel .
2. Remove the control panel .
-5-
Installation
3. Remove the PLASTIC COVER of the both sides away
PLASTIC COVER
4. Insert the two KEY PLAT into the grooves at both sides
of the unit as shown in figure until they click .
KEY PLATE
5. Pulling the levers makes it possible to remove
the unit from the dashboard .
Installation the unit
DASH BOARD
HEX NUT
METAL MOUNTING
STRAP
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT
-6-
Installation
How To Remove And Install The Front Panel
When detaching or attaching the control panel, be careful not to damage the
connectors on the back of the control panel and on the panel holder.
Detaching The Front Panel
Before detaching the control panel, be sure to turn off the power.
1). Press the “REL” release button and the left hand side of front panel will release.
RELEASE BUTTON
2). Pull-off the front panel and keep the front panel into the case .
PROTECTIVE CASE
Attaching The Front Panel
1). First insert the right hand side of the front panel into the hollow of the unit .
(NOTE : the “bulge” point on the panel must be attached into the hollow of the unit .)
2). Gently push the left hand side of the front panel until you feel a “ Click” .
Hollow
Bulge
PUSH
-7-
Panel Angle Adjustment
CHANGING THE CONTROL PANEL ANGLE
When you want to change the viewing angle of the operating unit to play,
you can touch the
on the front panel) repeatedly to select the desired angle as follows:
section on touch screen (or press the
button
ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGEL 4 - ANGLE 1 .
ANGLE 1
ANGLE 2
ANGLE 4
ANGLE 3
Caution:
Do not insert your finger behind the control panel.
-8-
Electric Connection
WIRING CONNECTION
MAIN UNIT
ISO CONNECTOR
WHITE
(B+)12V
REAR CAMERA SWITCH
BROWN
YELLOW
RADIO ANTENNA JACK
(B-)PARKING BRAKE
REAR CAMERA INPUT
RCA CABLE
GREY SUBWOOFER
VIDEO OUT 2 YELLOW
FUSE
IGNITION RED
SWITCH(B+)
COAXIAL OUT BROWN
RCH RED
REAR RCA OUTPUT
CABLE
LCH WHITE
MEMORY
BACK-UP(B+)
YELLOW
BLACK
FRONT RCA OUTPUT
CABLE
CHOKE
BOX
FRONT RCA RED
VIDEO OUT 1 YELLOW
FRONT RCA WHITE
R
GROUND(B-)
L
(FOR RCA LINE OUT VERSION ONLY)
FUSE
AUTO
ANTENNA
BLUE
GREY
WHITE
FRONT
FRONT
Rch SPK.
Lch SPK.
WHITE/BLACK
GREY/BLACK
VIOLET
REAR
GREEN
REAR
Rch SPK.
Lch SPK.
GREEN/BLACK
VIOLET/BLACK
Note:
the earth connection cable (parking brake B-) must be connected in order for DVD
pictures to be played back to the monitor. If the cable has not been correctly
connected, the message “PARKING BRAKE” appears on the monitor.
-9-
Remote Control
15
16
5
3
17
7
19
2
20
21
1
13
6
23
14
22
18
9
12
25
11
26
24
10
8
4
Function
Button
Ref #
Press it briefly to view the clock time , Press again to return to
normal display mode . Press longer to set the time .
1
2
CLK
Press it to use the Bluetooth function , refer to the page 33 .
PAIR/
Press once to pause playback. Press PLAY/PAUSE to resume
playback. Please note: if you press STOP twice, playback will
start at the beginning of the disc.
3
4
STOP
Press this button to open the SETUP menu.
SETUP
In Radio mode, press this button to change between Mono and
Stereo reception modes (when a station is weak, sometimes
switching to Mono will improve sound quality). In Disc Playback
mode, pressing this button opens the AUDIO setup menu for
making changes to the way the soundtrack is reproduced.
MO/ST
(AUDIO)
5
In DVD Disc Playback mode, pressing this button will allow you to
change the subtitle language on discs which have this as an
option.
In Radio mode, press this button to change the radio reception
sensitivity in stations are near or far.
SUBTITLE
LOCAL/
DISTANT
6
7
Redial/
Press this button to use the Bluetooth function, refer to page 33.
-10-
Remote Control
Function
Button
Ref #
Press it button to begin playback at a moment in the program you
designate. Use number buttons to enter the data that is needed.
In Bluetooth menu, it serves as the asterisk button on your mobile
handset.
8
GOTO
Press these buttons to skip ahead or back one track. (Note: In
DVD mode, press continually the
/
9
twice to skip back one)
Press this button repeatedly to cycle through the various audio
and video adjustments you can make: Volume, Bass, Treble,
Balance, Fader, Color, Brightness, Contrast and Tint.
10
SEL
Use these controls to adjust the volume level.
VOL+/-
11
12
Press to navigate the various menus present in the product.
/
/
/
Menu
SubWoofer
Press this button briefly to display the root level directory of a
DVD disc. Press and hold this button to turn on or off the
SUBWOOFER output.
13
(
)
In Radio mode, press this button repeatedly to switch between
the five radio bands: FM1 > FM2 > FM3 > AM1 > AM2.
In Disc Playback modes, Press this button to see information
about the disc currently in play.
BAND
(OSD)
14
15
Press this button to turn the unit ON , press and hold to turn the
unit OFF. Press it briefly to select the Disc, Radio , AUX In ,
BT Music mode.
/MOD
In Disc Playback mode, press to pause playback. Press again to
start where playback stopped.
PLAY/
PAUSE
16
17
Press this button to turn off the audio. Press again to restore the
sound to its prior volume level.
MUTE
When playing a DVD, pressing this button will open the TITLE
menu which is recorded on the DVD. When playing a VCD disc,
press this button to create a PBC (Playback Control) menu for the
disc to assist in making playback selections. In Radio mode,
press and hold this button to start the Auto-Program mode, during
which the tuner will scan for all strong stations and assign them
to the radio preset buttons.
TITLE/
PBC(A/P)
18
Press this button to adjust the screen viewing angle (see page 8).
19
20
For DVD discs which have alternate viewing angles encoded,
when you see the "angle mark" symbol advising you that these
angles are available, press this button to see them.
ANGLE
Press repeatedly to cycle through the different equalizer curve
presets you may wish to use for enhanced listening.
21
22
EQ/LOUD
/
In Disc Playback mode, press for fast forward/reverse playback.
-11-
Remote Control
Function
Button
Ref #
This button is used to confirm selections and settings within
many of the menus in the OSD system.
23
ENTER
Use to input numerical values during programming, with the GOTO
button, or to directly select a track to play .
24
0-9
In addition, in Radio Mode (when RDS is engaged), 0 serves as
the TA button and 9 serves as the AF button.
This button is used with the other number buttons for use with
two-digit number entries. In Bluetooth menu, it serves as the hash
button on your mobile handset.
25
26
+10/
1-6
Six numbered preset buttons store and recall stations for each band
Preparing the Remote Control
Inserting the Battery
1.First push to inside as the direction indicated by the arrow (See
1
)And then
).
Remove the battery holder as the direction indicated by the arrow (See
2
2.Replace the battery Set a new battery property with (+)side up as illustrated
(See ).
3
4
3.Insert the battery holder. Push in the holder to the original position(See
).
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each the direction of the front of the IR mark.
Note :
The lithium cell in the battery compartment of remote control has been secured for
transport with a foil . Before initial use please remove this foil so that the remote
control is ready for operation .
-12-
Control Panel
Key Functions
Touch Panel
MODE
MUTE ON
REDIAL
DIAL
VOLUME+
PAIR
VOLUME-
SEL
Touch Screen Key :
Changing the viewing angle
of the operating unit
REDIAL
Redialling
MODE
VOLUME-
Decrease the volume level
Operating mode selection
To switch of the sound
Select the menu of the
Picture/Sound
MUTE ON
SEL
Loading and ejecting the
DVD/CD
VOLUME+
Increase the volume level
Next menu
Registering devices with
one another
PAIR
DIAL
Calling up the Bluetooth
menu
-13-
Control Panel
Unit Keys :
11
10
9
8
7
6
5
4
12
13
3
2
1
1
AUX Input JACK
For information about connecting a AUX device, please see page 25 .
2
3
IR SENSOR
VOL+/ VOL- KNOB
In normal mode, this knob is used to increase or decrease the volume. It is also
used as an UP/DOWN knob when audio or video settings are being adjusted
when accessed using the SELECT button.
4
5
(POWER On/Off )/MODE BUTTON
Press this button to switch the device on. WELCOME appears in the display.
Press it again to switch the device off. SEE YOU appears in the display.
In playback mode, you can use the button to select the input mode by pressing
repeatedly until the proper one is found :
DISC > AUX IN > RADIO > BLUETOOTH MP3 .
ANGLE (Screen position)
Press this button repeatedly to cycle through the different positions.
-14-
Control Panel
6
REL BUTTON
Press this button to release the front panel for removal . Refer to see page 7.
7
/CH 1-6 (RADIO PRESET)BUTTON
A) In Disc Playback Mode
Press this button to pause playback, press it again to resume playback.
B) In Radio Mode
Press this button repeatedly to preset station. With this system a total of 30
stations can be stored in the memory . Each band store up to six preset
stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2
(MW2) band.
-Store in Memory
> Select the frequency band
> Press repeatedly the button to select the desired memory key .
> Select the station
> Keep the desired memory key pressed in until the station is heard again
after a brief interruption .
The operation as below:
-Retrieve a preset station
press the button repeatedly to retrieve a station which had been stored in the
memory in advance the chose number is shown on display .
8
9
SELECT BUTTON
To access the available adjustment settings for audio and video, press this
button repeatedly to cycle through and select them:
Buzzer
Volume
Bass
Treble
Balance Fader
Tint
Contrast
Bright
Color
Bluetooth
(EJECT) BUTTON
Press it button to eject the DISC or insert the DISC to start play .
10 USB OPERATION
For information about connecting a USB device, please see page 35.
11 SD/MMC CARD SLOT
12 MIC
Microphone .
13 RESET BUTTON
Press this button to return to factory settings .
-15-
Basic Operation
POWER On/Off
Mute Function
Touch “MUTE ON” range,
Press it to switch the device ON,
press and hold about 2 seconds
to switch the device OFF.
MUTE ON
it will mute the sound
but the disc continues
playing . Touch it again
to resume .
Ejecting The Disc
Use your finger to touch the
range on touch screen ,
the control panel of the unit
Setting The Clock
Touch briefly the “CLK”range
CLK
will swing downwards . Then
you can insert the disc or eject the disc .
to show/hide the clock .
Touch hold for more than 2’s
the hour will flash ,use the
VOL+/- to adjust .Touch it again, the
minute will flash, then use the VOL+/-
to adjust .
Select Sources
Touch repeatedly the MOD
section on the screen, the
MODE
Setting The Buzzer ON/OFF
signals will display in the
screen as follow :
Repeatedly touch “SEL” range
to select the BUZZER item, and
SEL
DISC
AUX IN
the use the VOL+/- to switch the
BUZZER ON/OFF .
RADIO
BLUETOOTH MP3
Setting the Background Color
In radio mode, repeatedly touch
SEL
Volume Adjusting
the “ SEL ”range to select the
“wallpaper” item, and then use
the VOL+/- to select the back-
Volume button
A
ground color among of the “wallpaper
AUTO, wallpaper: 01 ...... wallpaper: 11”,
in the “AUTO” mode, the monitor of unit
will change the background color
automatically .
Revolve : clockwise to increase /
Anticlockwise to decrease .
Touch screen
Touch the screen the
VOLUME- to decrease
the volume level .
VOLUME-
Setting Blue-tooth ON/OFF
Repeatedly touch “SEL” range
SEL
to select the Bluetooth item, and
the use the VOL+/- to switch the
Bluetooth ON/OFF .
VOLUME+
Touch the screen the
VOLUME+ to increase
the volume level .
-16-
Basic Operation
Rear View Camera
TFT Monitor Adjustment
When connecting the rear view camera.
the mirror image of the rear view through
the rear view camera is automatically
displayed on the monitor when you
change the gear to the back position.
(The monitor on the unit only.)
During DISC playback, use your
SEL
finger to touch briefly the SEL
section on the screen (or press
SEL button on front panel)
to access the Picture mode
selection menu, by repeatedly touch the
SEL section, and then touch the VOL+/-
(or rotate the VOL+/-) to adjust the
selected mode .
(The corresponding value will show on
the monitor )
Audio Quality Adjustment
During DISC playback, use your
SEL
finger to touch briefly the SEL
section on the screen (or press
SEL button on the front panel )
Volume
Bluetooth
Buzzer
Tint
Bass
Treble
Balance
to access the Sound mode selection
menu, by repeatedly touch the SEL
section, and then touch the vol+/-
(or rotate the vol+/-) to adjust the
selected mode . (The corresponding
value will show on the monitor )
Fade
Color
Contrast
Bright
Volume
Bluetooth
Buzzer
Tint
Bass
Treble
Balance
BRIGHT 16
Fade
Color
MODE
MUTE ON
Contrast
Bright
VOLUME-
VOLUME+
SEL
FLAT
12: 18
DISC-IN
touch to select
TREBLE +02
MODE
MUTE ON
VOLUME+
touch to adjust
ADJUSTABLE ITEMS:
COLOR: 0 to 32
VOLUME-
SEL
Adjust the color for the picture-lighter or
darker.
BRIGHT: 0 to 32
touch to select
Adjust if the picture is too bright or
too dark.
CONTRAST: 0 to 32
touch to adjust
Adjust the contrast of the bright and dark
portion.
TINT: 0 to 32
Adjust the tint if the human skin color is
unnatural.
ADJUSTABLE ITEMS:
Volume: 0 to 32
Adjust volume level by using VOL + / - .
Bass: -14 to +14
Adjust bass level by using VOL + / - .
Treble: -14 to +14
Adjust treble level by using VOL + / - .
-Adjustable when “NTSC “ is selected for
“NTSC/PAL “ .
-17-
Basic Operation
Balance: R 0-10 to L 0-10 .
ALTERNATE AUDIO/VIDEO SOURCE
Adjust sound balance between left
and right speakers by using VOL + / - .
Fader: F 0-10 to R 0 -10 .
Adjust sound balance between front and
rear speakers by using VOL + / VOL - .
On the front panel of the unit , there is an
AUX IN jack, to connect analogue replay
devices. Use this jack to replay sound of
other replay equipment such as
DVD players, computers, etc.
Setting Audio Modes
Via the loudspeakers.
1). Please following the diagram below,
connect the external device with stereo
jack plug the AUX IN socket .
Touch the screen the DSP range
DSP
(or press the EQ button on the
2). Press the MOD button to select the
AUX IN connection.
remote control ) to select one of
the preset sound modes .
3). Use the buttons on the external
device itself to operate it .
(Rock/Pop/Jazz/Classic/Flat) .
The information will display in the
monitor as follow :
JAZZ
POP
ROCK
AUX IN
FLAT
CLASSIC
FLAT
16: 18
AUX IN
DISC-IN
ROCK
REPEAT
RANDOM
S-WOOFER
OSD
INTRO
TA
AF
CLK
LUD
DSP
GOTO
Headphones
port
touch to select
It`s depend on your habit to select the
Audio mode .
Reset Factory Settings
RESET button is placed on the housing
and must be activated with either a
ballpoint pen or thin metal object.
The RESET button is to be activated for
the following reasons:
A. Initial installation of the unit when
all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
-18-
Radio Operation
select the band , the message will show
in turn :
Listening to the Radio
Switching To Radio Mode
FM1
FM2
FM3
Touch the screen of “MODE”
range (or press the MOD button
on the front panel ) repeatedly to
MODE
AM1(MW1)
AM2(MW2)
select the RADIO mode. the following
information will appears as below:
Start Searching For a Station
Manual Search
FLAT
12:06
TA
NO-DISC
DX
ST
During Radio mode, briefly touch the
screen of
MHZ
FM1
87.60
“
” section to increase
MODE
MUTE ON
frequency by one step of channel
spacing .
1
2
3
4
5
6
Briefly touch the “
decrease frequency by one step of
channel spacing .
” section to
VOLUME-
SEL
VOLUME+
Automatic Search
FLAT
ST
12:06
AF
DX
NO-DISC
MHZ
During Radio mode, touch and hold
(for more than 2’s ) the screen of “
section to start search for a radio
station automatically .
FM1
BND
87.60
S-WOOFER
/
”
APS
REDIAL
PAIR
DIAL
STEREO/MONO
DSP
When an FM stereo broadcast is
hard to receive
FLAT
12:06
AF
NO-DISC
MHZ
DX
ST
Touch the “STEREO/MONO” section on
FM1
87.60
touch screen (or press ST/MO button on
the remote control ) to select the MONO
or STEREO mode .
TA
PTY
AF
CLOCK
LOUDNESS
(When Stereo mode is activated, the ST
symbol will appear . )
LOC
Touch “
Touch “
” to next .
To tune in strong-singnal FM
Station only (LO/DX function)
” to previous .
Touch the “ LOC ” range on the touch
screen (or press LO/DX button on the
remote control ) to select the LOCAL
or DX mode .
Selecting The Frequency Band
BND
( You can choose between the LOCAL
and DX(DISTANCE) mode for local or
long-distance traffic news . )
Touch the screen of “ BND ”
section repeatedly to
-19-
Radio Operation
e.g. FM1, for the stronger signal
level until the search cycle has finished .
The six strongest stations are then
allocated to the corresponding storage
locations . Then the station of the first
storage location is set .
Storing Stations In Memory
With this system, a total of 30 stations
can be stored in the memory of six
buttons. Each band stores up to six
preset stations. The stations might be
FM1, FM2, FM3, AM1(MW1), and
AM2(MW2) band.
Scan Function
The operation is as below :
APS
In Radio mode, briefly touch the
APS section on the touch screen ,
the radio briefly plays all the
Touch the screen of the “ 1-6 ”sections
FLAT
12:06
TA
preset stations of the frequency band .
NO-DISC
DX
ST
MHZ
FM1
87.60
MODE
MUTE ON
1
2
3
4
5
6
RDS FUNCTION
VOLUME-
SEL
VOLUME+
In Radio mode, touch it to select
the desired item, it will display the
following as below :
Touch to preset station
FLAT
12:06
AF
DX
NO-DISC
MHZ
-Store in Memory
ST
FM1
87.60
> Select the frequency band
> Select the station
> Keep the desired memory key pressed
in until the station is heard again after a
brief interruption .
Touch to select
TA
PTY
AF
CLOCK
LOUDNESS
LOC
-Retrieve a preset station
TA Traffic Annonuncement
(priority For Traffic Information)
Touch the 1-6 sections briefly to retrieve
a station which had been stored in the
memory in advance the chose number
is shown on display .
In Radio mode, touch briefly the
screen of “TA” range to activate
the TA function.
TA
Automatic Memory Storing &
Program Scanning
Touch it again to turn off the TA function .
When the TA function is activated, the
TA symbol appears in the display .
During radio operation in one FM
frequency band the search for a traffic
announcement station is started
automatically (TA SEEK) .
Automatic Preset Setup
In Radio Mode, Touch and keep the
APS section on the touch screen
for about 2 seconds to active
APS
If an FM station is being received which
transmits the latest traffic announce-
ments from time to time, the TP display
lights up.
automatic station storage. The radio
searches within the current frequency
band,
-20-
Radio Operation
Note :
the status of the AF function is shown by
an AF symbol in the display.
If the AF symbol appears in the display,
the AF function is switched on and RDS
transmission date is being received .
If the AF symbol flashes in the display,
the AF function is selected but no RDS
signal can be received at the moment .
When the TA function is switched on ,
the FM traffic automatically interrupt CD
operation(the word TRAFFIC appears
in the display).
The volume level is increased to the
minimum value for the transmission of
traffic announcements.
After the traffic announcements has
finished, the program that was previously
running is resumed.
PTY FUNCTION
Interruption of the TA Function:
if you would like to interrupt the current
traffic announcement, touch the TA
section on screen briefly . This does
switch off the TA mode .
In Radio mode, touch the screen
of “PTY” range to select the
Program type .
PTY
PTY Selection of the program type
besides the stations name, some FM
stations also transmit information on the
type of program. This information can
be displayed by your car radio .
AF FUNCTION
(Alternative Frequencies)
In Radio mode, touch briefly the
AF
screen of“AF” range to activate
the AF function. Touch it again
to turn off the AF function .
Examples of such types of program
are :
SPORT NEWS POP WEATHER ......
AF is a function that works with the help
of RDS (Radio Data System) and can
only be used with FM stations . The radio
searches in the background for the best
frequency reception of the station that
has been tuned into .
With PTY function you can specifically
select stations transmitting a particular
type of program. Touch the PTY range
on screen repeatedly to call up the PTY
selection menu . The message
“PTY SEEK” then appears briefly in the
display .
Touch the AF section on touch screen or
swing and keep the SEL knob in the
TA/AF direction for about 2 seconds ,
the AF function is activated. The AF
symbol appears in the display .
When PTY has been selected the radio
starts searching for corresponding PTY
information and stops when the PTY
information has been found, “NO PTY”
appears in the display. If the PTY
information being searched for no longer
exists, the PTY function automatically
switches to normal mode .
When the AF function has been switched
on, the radio continuously tests the
signal strength of the AF frequency .
The test interval for each AF frequency
depends on the signal strength of the
current station and varies from a few
minutes in the case of weak signals.
Whenever the new AF frequency is
stronger than the station that is currently
tuned in , the radio switched to this
frequency for a short time for a short
time and the message
“NEW FREQUENCY “ is displayed for
one or two seconds.
-21-
DISC Operation
Basic Operation
Switching the DVD mode
During DISC playback, you can touch
the screen to display the following:
Touch the screen of “MODE” range (or
press MOD button on the front panel ) to
select the DISC mode, it display like
following :
FLAT
12: 16
DISC-IN
FLAT
12: 16
DVD
1-0:00:16
MUTE ON
DISC-IN
MODE
DVD
1-0:00:16
MUTE ON
MODE
VOLUME-
VOLUME+
SEL
VOLUME-
VOLUME+
SEL
FLAT
12: 16
DISC-IN
Function setup
(different the source the display is different)
DVD
1-0:00:16
DIAL
PAIR
REDIAL
ZOOM
AUDIO
SUBTITLE
TITLE
Stopping Play
SETUP
Touch the screen the range (or
press the button on remote
control .) To stop the unit playback.
Touch the section or press
button on front panel to start play.
FLAT
12: 16
DISC-IN
DVD
1-0:00:16
RANDOM
REPEAT
INTRO
S-WOOFER
OSD
TA
AF
CLK
LUD
Pause (still picture)
DSP
GOTO
Touch the “
” section on touch
screen during playback will stop
play temporary, touch it again to
return the normal playback .
FLAT
12: 16
DISC-IN
DVD
1-0:00:16
Rapid Forward/Rapid Reverse
During DISC playback, touch the
/
OK
screen of “
” range the
speed of rapid forward/reverse
changes according to the disc as
follow:
Touch “
Touch “
” to next .
DVD/VCD/CD/MP3:
Normal Playback 2x
” to previous .
4x
8x
16x
-22-
DISC Operation
Selecting The Play Modes
Skipping Track
During the Disc playback, touch the
touch screen, it will display the following
as below :
During DISC playback, Touch the
/ section on the touch screen
to skip to next/back one track.
FLAT
12: 16
DISC-IN
DVD
1-0:00:16
RANDOM
REPEAT
INTRO
Note :
1. In DVD mode, touch the
continually twice to back one track .
2. For some VCD2.0 disc (PBC-playback
control), above these buttons may be
unavailable .
section
S-WOOFER
OSD
TA
AF
CLK
LUD
DSP
GOTO
Touch to select
Zoom Function
1). Repeat Function
FOR DVD :
Repeatedly touch the section of
the ZOOM, the displaying rate
can be 2x, 3x, 4x, 1/2, 1/3, 1/4 .
ZOOM
Touch the screen the of“REPEAT”range
(or press longer 2/RPT button on the
remote control) to select REPEAT mode
as follow :
Use the direction keys (
remote control or
screen) to move the enlarged picture .
Note: During the JPEG disc playback ,
touch the screen of “ZOOM” range , the
“zoom 100%” word will display, then you
/
/
/ on
on touch
/
/
/
CHAPTER REPEAT ON
TITLE REPEAT ON
REPEAT ALL
can touch shortly the
touch screen (or press the
/
section on
buttons
/
FOR VCD/CD/MP3 :
on remote control ) to zoom in/zoom out
the picture. In zoomed mode, use the
direction keys to move the enlarged
picture .
Touch the screen the of“REPEAT”range
(or press longer 2/RPT button on the
remote control) to select REPEAT mode
as follow :
REPEAT ONE
REPEAT ALL
REPEAT OFF
Loud Function
Touch the screen of“ LUD ” range
to switch the Loudness function
ON or OFF.
1. Continuously repeat at the current
chapter/track, when selected REP-ONE
mode .
LUD
2. Select REP-ALL mode to continuously
repeat all chapter/track on the current
disc .
Subwoofer Function
2). RDM(RANDOM) Function
S-WOOFER
Use your finger touch the
“ S-WOOFER“ section on the
screen to turn on the Subwoofer
function, touch it again to
cancel function .
During DISC playback, touch screen of
“RANDOM” section ( press the 4/RDM
button longer on the remote control to
play in random.
-23-
DISC Operation
Each playing, the order is different .
(Depend on the disc used for VCD).
Touch it again to cancel this function .
DISC Search (GOTO)
FLAT
12: 16
DISC-IN
Note : in random mode, the
not available .
button is
DVD
1-0:00:16
RANDOM
REPEAT
INTRO
S-WOOFER
OSD
TA
AF
CLK
LUD
3). INT Function
FOR CD :
DSP
GOTO
Touch the screen of the “INTRO” section
(or longer press the 3/INT button on the
remote control ) to play the previous 6
seconds part of each track/chapter on
disc. (Touch it again to cancel this mode)
Touch to select
FLAT
12:16
DISC-IN
DVD
1-0:00:16
GOTO
ENTER
FOR VCD :
0
1
6
2
7
3
8
4
9
5
Touch the screen of the “INTRO”section
(or longer press the 3/INT button on the
the remote control ). It display will
following menu as below :
+10
(touch it again to cancel this mode .)
FOR DVD :
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
Touch the screen the of “GOTO” range
(or press the GOTO button on the remote
control ) Twice, the screen will display
the following message :
TRACK INTERVAL
Use the UP, DOWN, LEFT and RIGHT
arrows on the remote to select the item,
and then press ENTER to confirm .
Title 01/01 Time -:--:--
0:10:36
FOR DVD :
Touch the screen of the “INTRO”section
(or longer press the 3/INT button on the
the remote control ). It display will
following menu as below :
You can select the item you want to
watch through TIME setting by using
numberic buttons . (E.x. 0:10:36)
(touch it again to cancel this mode .)
FOR VCD (With PBC OFF):
SELECT DIGEST TYPE:
TITLE DIGEST
Touch the screen the of “GOTO” range
(or press the GOTO button on the remote
control )Once, the screen will display the
following message :
CHAPTER DIGEST
TITLE INTERVAL
CHAPTER INTERVAL
Disc Go To --:--
00:36
Use the UP, DOWN, LEFT and RIGHT
arrows on the remote to select the item,
and then press ENTER to confirm .
Use the numberic buttons to input the
time directly (E.x. : 00:36)
NOTE : For MP3, the 3/INT button is not
available.
-24-
DISC Operation
Note:
Touch and hold the
FLAT
12: 16
/
section on
DISC-IN
the touch screen , you can select the
title or chapter of DVD . (Only for the
DVD with title /chapter.)
AUX IN
TA
LUD
AF
DSP
AUX Operation
S-WOOFER
CLK
On the front panel of this unit, there is an
AUX IN jack, follow the diagram below to
connect analogue replay devices.
Use this jack to replay sound of other
replay equipment such as DVD players,
computers, etc. Via the loudspeakers.
3). You now hear the sound from the
external device played back through
the loudspeakers .
4). Touch the volume+/- sections on
touch screen or use the VOL+/- on
the remote to adjust the volume level.
AUX IN JACK FRONT PANEL
AUX IN
M
VIDEO IN (yellow)
RCH IN (red)
LCH IN (white)
1). Please connect the external device
with stereo jack plug the Aux in socket .
2). Touch the MOD section on screen
or press the MOD button to select the
AUX IN connection. It will display the
following as below :
FLAT
12: 16
DISC-IN
AUX IN
MODE
MUTE ON
REDIAL
PAIR
DIAL
VOLUME+
VOLUME-
SEL
-25-
DISC Operation
ON-SCREEN DISPLAY FUNCTION
2.Example for VCD/SVCD/CD:
A.Touch or Press OSD for first time:
During playback, touch the screen
OSD
the OSD section (or press the OSD
on the remote), it will display the
following as below :
SINGLE ELAPSED
TRACK 01/16
0:00:56
1. DVD:
A.Touch or Press OSD for first time:
B.Touch or Press OSD for second time:
TITLE ELAPSED
SINGLE REMAIN
T 01/01 C 01/38
0:02:06
TRACK 01/16
0:05:10
Title Number, Total Title Number,
Chapter Number, Total Chapter Number
of this Title of the disc currently being
played will be shown on the screen,
along with the elapsed time.
C.Touch or Press OSD for hird time:
TOTAL ELAPSED
TRACK 01/16
0:31:36
B.Touch or Press OSD for second time:
D.Touch or Press OSD for fourth time:
TITLE REMAIN
T 01/01 C 01/38 3:24:36
TOTAL REMAIN
TRACK 01/16
0:36:26
C.Touch or Press OSD for hird time:
E.Touch or Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
CHAPTER ELAPSED
T 01/01 C 01/38 0:02:56
NOTE:
For CD and MP3,the message will
always display on the screen.
D.Touch or Press OSD for fourth time:
CHAPTER REMAIN
3.Example for MP3:
Each time OSD is pressed or touch , the
message displayed on screen changes
as follows:
T 01/01 C 01/38 0:04:32
SINGLE ELAPSED
SINGLE REMAIN
E. Touch or Press OSD for fifth time:
The message on the screen will be
cleared.
-26-
DISC Special Functions
For VCD/CD:
DVD/VCD Special Function
during playback, touch the AUDIO
section of the touch screen or Press
AUDIO on the remote . It is possible to
switch the sound between monaural
and stereo sound.
FLAT
12: 16
DISC-IN
DVD
1-0:00:16
DIAL
PAIR
REDIAL
ZOOM
MONO LEFT
MONO RIGHT
MIX-MONO
STEREO
AUDIO
SUBTITLE
TITLE
SETUP
3. Multi-Angle Function
(for DVD Only)
Touch to select
During DVD playback, press the ANGLE
(
) button on the remote control .
1. Multi-subtitle Language
Function (for DVD Only)
Each time the button is pressed ,
the number of the angle changes in
sequential order.
SUBTITLE
During DVD playback. Touch
the SUBTITLE section on touch
screen(or press the SUBTITLE
on the remote) .
Notes:
- The angle number is different
according to the disc.
- The function only work for disc having
scenes recorded at different angles.
- When no different angle are recorded,
will be displayed at screen left top
corner.
Each time the button is pressed or touch,
number of the subtitle language changes
in sequential order.
Notes:
- The language number is different
according to the disc.
- Some discs only contain one subtitle
language.
- When no different subtitle language
4. Title Menu Function
are recorded, will be displayed
at screen left top corner.
For DVD:
TITLE
If the DVD has multiple titles
recorded on the disc. It can
select preferred title from the
title menu to start playback.
- During DVD playback, touch the TITLE
section or press TITLE button on the
remote .The title menu is display.
- Touch the cursor button shown in TV
screen, select preferred title by the
cursor button and confirmed by touch
ENT button .
2. Multi-Audio Language Function
For DVD:
During DVD playback , touch
AUDIO
the AUDIO section on touch
screen (or press the AUDIO
on the remote .) Each time the button is
pressed or touch , number of the audio
soundtrack language changes on
sequential order.
For VCD:
Press TITLE/PBC button on the remote
control while the disc is playing, you can
switch between "PBC on"and "PBC off"
mode.
Notes:
- The language number is different
according to the disc.
- Some disc only contain one language
soundtrack
- When no different language
soundtrack are recorded
display at screen left top corner.
will be
-27-
SETUP
GENERAL SETUP
--- GENERAL PAGE ---
DOLBY
DOLBY
-----General setup page----
-----General setup page----
TV Display
Normal/PS
Normal/LB
Wide
TV Display
LB
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
Spdif Output
Captions
ENG
SPDIF/RAW
ON
Screen Saver
Last Memory
Screen Saver
Last Memory
ON
ON
Set TV Display Mode
Go To General Setup Page
TV Screen
Video
Material
1. Press SETUP button on the remote
control .
Wide(16:9)
Pan Scan
Normal
Letter-box
4:3
2.The SETUP menu is displayed.
3.Select the preferred item by using the
/
/
/
buttons
4.Press ENTER button.
a.GENERAL SETUP
1.TV DISPLAY SETUP
This setup page includes the item
of TV display & audio output feature.
The detail please refer to
This is to select the appropriate TV
aspect (4:3 or 16:9) according to the
connected TV set.
GENERAL SETUP MENU.
b.SPEAKER SETUP
Normal/PS (For 4:3 TV)
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the
left and right edges are cut off.)
Normal/LB (For 4:3 TV)
This is to activate the audio output
from DOLBY AC3 5.1 DOWNMIX
to 2 channel mode. Please refer to
SPEAKER SETUP MENU.
c.DOLBY DIGITAL SETUP
Please refer to DOLBY DIGITAL
SETUP.
Played back in letterbox style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
d.PREFERENCE SETUP
This setup page includes all the
configuration of support feature.
The detail please refer to
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
PREFERENCES SETUP MENU.
-28-
SETUP
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
Osd Lang
OFF
SPDIF OFF
SPDIF/RAW
SPDIF/PCM
Spdif Output
Captions
Screen Saver
Last Memory
Set Angle Mark
Screen Saver
Last Memory
Setup SPDIF
2.ANGLE MARK DISPLAY SETUP
If it is set to ON, when the multi-angle
4.SPDIF OUTPUT
This is to activate the audio output
from SPDIF OFF mode to SPDIF/RAW
mode to SPDIF/PCM mode.
DVD disc is playing,
(the angle
mark) will appears on the screen; if is
set to OFF, the mark will not appear.
DOLBY
DOLBY
-----General setup page----
-----General setup page----
TV Display
TV Display
Angle Mark
OSD Lang
Spdif Output
Captions
English
French
Angle Mark
OSD Lang
German
Spanish
Italian
ON
Spdif Output
OFF
Captions
Portuguese
Russian
Screen Saver
Last Memory
Screen Saver
Last Memory
Closed Caption
Set OSD Language
5.CAPTIONS SETUP
3.OSD LANG TYPE SETUP
Select the preferred OSD language
Activate the CAPTIONS feature by
selecting ON. And release this feat-
ure by selecting OFF.
by using the
/
buttons.
-29-
SETUP
SPEAKER SETUP
--- SPEAKER SETUP PAGE ---
DOLBY
DOLBY
-----General setup page----
TV Display
-----Speaker Setup Page----
Angle Mark
OSDLang
Spdif Output
Captions
DOWNMIX
LT/RT
STEREO
ON
Screen Saver
Last Memory
Screen Saver
OFF
Set Downmix Mode
This is to activate the audio output from
DOLBYAC3 5.1 DOWNMIX to 2 channel
mode. Select the preferred SPEAKER
connection by using the cursor buttons.
Select the LT/RT to activate the Dolby
surround compatible output.
6.SCR SAVER SETUP
Select the SCR SAVER output
ON/OFF.
Select the STEREO to activate simple
stereo mode.
DOLBY
DOLBY DIGITAL SETUP
DOLBY
-----General setup page----
TV Display
-----Dolby Digital Setup----
Angle Mark
OSD Lang
Spdif Output
Captions
FULL
6/8
DYNAMIC
4/8
2/8
ON
Screen Saver
OFF
OFF
Last Memory
Set Last Memory State
Set DRC OFF
DYNAMIC RANGE CONTROL
Select DRC and adjust the dynamic
range of a Doby Digital encoded
7.LAST MEMORY SETUP
Select the LAST MEMORY output
ON/OFF.
program. There are 8 steps between
full compression and off compression.
-30-
SETUP
PREFERENCES SETUP
--- PREFERENCES PAGE ---
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
English
French
German
Spanish
Italian
TV Type
PAL
Audio
AUTO
NTSC
Audio
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
Disc Menu
Parental
Password
Default
Portuguese
Russian
OFF
Set TV standard
Preferred Subtitle Language
1.TV TYPE SETUP
This player can play discs recorded
in either PAL or NTSC format.Select
NTSC format, when you connected to
NTSC TV.Select PAL format, when
you connected to PAL TV.Select AUTO
format, the player TV output format
will according to the DVD disc format..
3.SUBTITLE LANGUAGE SETUP
Select the preferred SUBTITLE
language by using the cursor buttons.
DOLBY
DOLBY
-----Preference Page----
TV Type
English
-----Preference Page----
Audio
TV Type
English
French
Subtitle
German
Spanish
Italian
Audio
French
Disc Menu
Parental
Password
Default
Subtitle
Disc Menu
Parental
Password
Default
German
Spanish
Italian
Portuguese
Russian
Portuguese
Russian
Preferred Menu Language
Preferred Audio Language
4.DISC MENU LANGUAGE SETUP
Select the preferred DISC MENU
language by using the cursor
buttons.
2.AUDIO LANGUAGE SETUP
Select the preferred AUDIO sound-
track by using the cursor buttons.
-31-
SETUP
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
1KID SAF
2G
TV Type
Audio
Audio
3PG
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
4PG13
5PGR
6R
Disc Menu
Parental
Password
Default
7NC 17
8 ADULT
OFF
RESET
Load Fcatory Setting
Set Parental Control
7.DEFAULTS
Select reset to become factory initial
setting.
5.PARENTAL
Select suitable parental guidance by
the cursor buttons and conformed by
pressing ENTER button.
DEFAULTS TABLE
DOLBY
TV DISPLAY
NORMAL/LB
ON
-----Preference Page----
TV Type
ANGLE MARK
OSD LANGUAGE
ENGLISH
SPDIF/RAM
ON
GENERAL SETUP
Audio
SPDIF OUPUT
CAPTIONS
Subtitle
Disc Menu
Parental
SCR SAVER
ON
LAST MEMORY
ON
DOWNMIX
SPEAKER SETUP
DOLBY DIGITAL
STEREO
OFF
Password
Default
CHANGE
DYNAMIC
TV TYPE
AUDIO
AUTO
ENGLISH
OFF
Change Password
SUBTITLE
6.PASSWORD
DISC MENU
Select the change and press ENTER
button. Type the old password (The
initial factory code is 1379) and key
in 4 characters password now you
want to use, and retype again to
confirm key in correctly.
PREFERENCES
ENGLISH
8 ADULT
1379
PARENTAL
PASSWORD
-32-
Bluetooth Operation
5). Enter passkey “8888”, then press
“OK” to pair the Car Kit and the handset,
the word “PAIR OK” , will display in the
TFT .
Bluetooth Car Kit User Manual
1.“Pair”To Your Bluetooth Phone
Prior to using the Car Kit for the fist time,
you must pair it with a Bluetooth-enabled
mobile handset.
The following steps describes pairing
the instruction for a typical Bluetooth-
enabled mobile handset.
6). Select the “CONNECT” from the list
on the phone, if you connect success-
fully , the
ICON remains solid on
the screen , then you can operate the
function of blue-tooth about the unite .
Touch the touch screen , the touch
operation menu will display.
Important:
Touch the “ ” section to select ,
it will display following as below :
1). If the pairing can not be completed
within approximately 2 minutes , whiles
the pairing mode is activated, and you
will need to reattempt pairing
FLAT
12: 16
DISC-IN
(See steps 2-5 above) .
DVD
1-0:00:16
DIAL
2). After pairing is completed, if the
ICON is stilling flash on the TFT ,
please follow the steps to reattempt
pairing through your handset until the
ICON remains solid on the screen.
PAIR
REDIAL
ZOOM
AUDIO
SUBTITLE
TITLE
SETUP
2. Using The Bluetooth Car Kit.
Once connecting is complete, you may
access the following function. Some of
the below mentioned functions only
accessible for handset supported with
hands-free profile.
Touch to select
1). Place the Car Kit and mobile handset
in 3 meters apart.
2). Put the Car Kit in pairing mode.
a. Press the POWER button to turn ON,
the ICON will flash on the TFT .
Make a call
Touch the screen of “ DIAL ” range,
(or press briefly the “ PAIR/ ” button
on the remote control ) the word
PAIR
b. Touch the screen of “
” range
or press the“PAIR/ ”on the remote
control until the word “BLUETOOTH
PAIRING ” display, it’s now ready
for pairing.
“DIAL NUMBERS” will display on the TFT .
then you can touch the number section
on screen (or dial the number buttons on
the remote control ), and then touch the
“
DIAL ” section or press “ PAIR/
button to confirm .
”
3). Set your bluetooth phone to
“discover”the Car Kit .
Following your phone’s instruction
guide for details, active your mobile
handset’s Bluetooth function, the
handset will search for accessible
Bluetooth devices.
Note: When you dial the wrong number,
you can touch the screen “ CLEAR ” to
delete the wrong number . (You can also
press the “ ” button on the remote
control to do so .)
Please note : “ ” and “ ” serves as
the “ ” and “ ” button on your
mobile handset .
4). Your phone will find this Car Kit .
Select this Car Kit from the list.
-33-
Bluetooth Operation
Adjust the Volume
Touch the screen of “
the message will display as below :
DIAL ” section ,
During conversation in progress,
tune the Volume switch until you reach
the desired volume level.
DIAL NUMBERS
1
6
2
7
3
8
4
9
5
0
Play BT music
touch to dial
In Bluetooth menu, touch the screen of
“MODE” range to select the “BT MUSIC”,
you can play the BT MUSIC from your
mobile handset.
CLEAR
DIAL
CALL CONNECTED
MUTE ON
FLAT
08: 16
DISC-IN
BLUETOOTH
MP3
REJECT
PICKUP
MODE
MUTE ON
VOLUME-
SEL
VOLUME+
S-WOOFER
VOLUME-
SEL
VOLUME+
Answer a call
After you hear the ring tone,
the incoming telephone number will
display on the TFT LCD .
PICKUP
touch to select
Touch the screen of “
” range to
listen or press the “PAIR/ ” button on
the remote control .
Note:
please make sure it support the
Bluetooth A2DP & AVRCP profile.
Call Transfer
During talking mode , user can touch
the screen of the “ PICKUP ” range (or
press the “PAIR/ ” button on the remote
control ) to transfer the audio from the
unit back to the mobile phone for privacy
reason .
Note:
1). Before using the function of the Blue-
tooth about the unit , please check your
phone’s instruction guide or contact
phone manufacture if you are not sure
if your phone supports the hands-free
Bluetooth function .
End/Reject a call
2). When operating the function of blue-
tooth about the unit , you need make
your call-phone and the unit success-
fully for one time. Afterwards, you only
need to take on the power and the
function of blue-tooth will work in three
minutes automatically if you want to
operate the function of blue-tooth .
In Bluetooth menu, touch the screen
REJECT
of “
” range (or press briefly
“REDIAL/ ” button on remote control ) ,
the message display the
“CALL HOOKED/CALL EJECTED” .
Redial last number
REDIAL
In Bluetooth menu, touch the “
(or press longer “ REDIAL/
on the remote control the
”
” button
3). If you want not to use the function of
the Blue-tooth about the unit , you can
select the Bluetooth OFF .
“DIAL LAST CALL/DIAL OUT NOW ” will
display on the TFT LCD.
(The method to see the page 16.)
-34-
Other Main Operation
USB Operation
Changing From DISC to USB Playback
Modes
If the disc present in the player is an
Following the diagram below, connect
your USB device to the front panel
USB port . If it is properly connected,
the device will be mounted and start
playing automatically.
MP3 disc, touch
section on screen
or press the STOP on remote once then
touch or press the GOTO to USB
playback.
If the disc present in the player is an
DVD or VCD or CD disc, touch
on
the screen or press STOP twice on the
remote then touch GOTO section on
the screen or press the GOTO button
on the remote to USB playback.
Important Note:
To prevent damage to the USB device,
do not remove or disconnect it during
playback. it is also a good practice to
remove the USB drive during disc
playback.
In USB Playback mode
Use the UP, DOWN, RIGHT or LEFT
buttons to navigate to and select files
to play, and press ENTER to begin
playback (or viewing, in the case of
JPEG files). To skip to the next or last
track, touch or press the
Press the or buttons for Fast
or
.
Forward or Fast Reverse playback.
REPEAT play modes are also available
by repeatedly pushing REPEAT until
the desired mode is found.
Changing From USB to DISC Playback
modes
If you are in USB Playback mode and
wish to begin playback of a disc already
in the player, touch the
range on the
touch screen or press the STOP on the
remote once. Then touch GOTO range
on the screen or press the GOTO on the
remote and the player will switch to
DVD/VCD/CD/MP3 Playback mode.
-35-
Other Main Operation
SD/MMC card OPERATION
The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are
stored into SD and MMC memory card .
Please read below before you start the operation of memory card .
Inserting and removing a SD or MMC card on the front panel of unit .
Inserting the SD or MMC card .
Label side facing
backward
Insert the memory card into slot
with label side facing backward .
Press in till heard a “CLICK”.
Removing the SD or MMC card .
Remove the memory card .
Press in till heard a “CLICK” .
Mode change to SD/MMC card
After a SD or MMC card was inserted into the main unit card slot . the unit will starts
playing the files contained on the memory card . Once the unit read the memory card
successfully, the first file on the memory card will automatically start playback.
Press the mode button repeatedly is allowing changing to other modes .
Change DISC to SD/MMC card
The operations are same as USB mode, refer to see USB operation .
Change SD/MMC card to DISC
The operations are same as USB mode, refer to see USB operation .
File Playback Operation
All the SD or MMC memory car playback operation function is same as the operation
on CD/MP3/WMA .
Please to “ MP3/WMA” operation for more details .
-36-
Other Main Operation
MP3/WMA/JPEG/MPEG4 DISC PLAY
When you insert a disc which contains MP3, WMA or JPEG files, the different file
types are detected, and a list of the files are produced, as shown in the diagram
below.
1 Current track(file)(highlighted bar)
2 Current track (file) number/total
number of tracks(files) in the current
folder.
4
5
6
Repeat one
00:56
04:07
3
2
003/112
3 Elapsed playing time of the current
track(not available for JPEG disc)
4 total playing time.( not available for
JPEG disc)
Mp3
K
P
Mp3
Mp3
1
1
woman
ton
5 Operation mode icon.
(stop), (pause),
(reverse).
(Play),
(forward)
..........n..e.w.
6 Selected playback mode
Touch the screen, it will display the following as below :
(when the parking brake is applied .)
FLAT
12: 16
FLAT
08: 16
DISC-IN
DISC-IN
MP3
02-0:36:20
MP3
02-0:36:20
MODE
MUTE ON
Touch repeatedly
OK
VOLUME-
SEL
VOLUME+
In stop mode, touch the
/
/
/
sections on touch screen (or Use
/
on the remote control ) to select the item or folder, then touch the “OK” range
/
/
(or press ENTER button on the remote control ) to confirm.
Touch the screen of“REPEAT ”range or press longer “2/RPT” on the remote control
repeatedly can select two kinds of repeat play mode.
REP-ONE:
Play the same song over and over again.
REP ALL:
Play all songs on the disc, then repeats the entire disc over and over again .
Moving To Another Track :
1. Touch the
2. Press the
or
or
range on the touch screen to skip a track ahead or back.
button on the remote control to skip a track ahead or back.
Fast Forward/Fast Backward
1. Touch briefly the “
2. Press briefly the
/
or
” range on touch screen for fast forward / fast backward .
button on the remote control for forward or backward .
-37-
Specification
Generall :
Supply Voltage:
Current Consumption:
Signal System:
Discs Played:
12V DC (11V-15V)
Less than10 A
Compositive video 1.0Vp-p 75
(1)DVD-VIDEO Disc
5"(12 cm) single-sided, single-layer
5"(12 cm) single-sided, double-layer
(2)Compact Disc (CD-DA, VIDEO CD)
5"(12cm) disc
Audio Signal Output:
Characteristics:
2ch&4ch line out
(1)Frequency Response
(2)S/N Ratio
20 Hz - 20 KHz
90 dB (JIS)
(3)Wow and Flutter
Below measurable limits
RADIO Section:
For 3 Bands
(Europe)
FM
For 2 Bands
For 2 Bands
(U.S.A.)
FM
(Europe)
FM
Frequency Coverage:
IF:
87.5 to108 MHz 87.5 to108 MHz 87.5 to107.9 MHz
10.7 MHz
10.7 MHz
15 dBu
MW
10.7 MHz
15dBu
AM
Sensitivity (S/N = 30 dB): 15 dBu
MW
Frequency Coverage:
IF:
522 to1620 KHz 522 to1620 KHz 530 to1710 KHz
450 KHz
450 KHz
40 dBu
450 KHz
40 dBu
Sensitivity (S/N = 20 dB): 40 dBu
TFT Monitor:
Monitor Screen Size:
Number of Pixels:
Color System:
7 Inch Wide
480 X RGB X 234 pixels
NTSC/PAL
BLUETOOTH:
Bluetooth specification:
V1.2 Class 2
Bluetooth profile supported: Headset, Handsfree and A2DP & AVRCP profiles
Range of frequency:
2.4GHz Spectrum
NOTE:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
-38-
Trouble Shooting
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
SYMPTOM
No power
CAUSE
SOLUTION
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
The car ignition switch is
not on
The fuse is blown
Replace the fuse
Presence of disc inside the Remove the disc in the player,
player.
then put a new one
Inserting the disc in reverse Insert the compact disc with
direction
Disc can not be
loaded or ejected
the label facing upward
Clean the disc or try to play a
new one
The disc is extremely dirty
or defective
Cool off or until the ambient
temperature return to normal
Temperature inside the car
is too high
Television/video
imageappears
black-white
Please switch to correct color
system from menu
The color system is
set incorrectly
Make proper connection
The unit is not connected
to the parking brake
detection switch
No television/video
image appears
according to“wire connection”
For safety reasons no television
/video images are displayed
while the vehicle is moving.
Engaging the parking brake will
cause images to be displayed.
The parking brake is not
engaged
The disc format is not
accordingto the TV-set
used (PAL/NTSC)
Please the television mode of
the choice accommodation
No color in picture
No JPEG files are recorded
on the disc.
JPEG disc can
not be played
back
Change the disc
Change the disc Record JPEG
files using a compliant
application
JPEG files are not recorded
in a compliant formant
The built-in microcomputer Press the RESET button.
is not operating properly
due to noise
The operation keys
do not work
Front panel is not properly fixed
into its place
The antenna cable is not
connected
The radio does not
work
Insert the antenna cable firmly
The signals are too weak
Select a station manually
8880-J9000-04S
-39-
|