PYLE Audio Car Video System PLCD19XMR User Manual

PLCD19XMR  
OWNER’S MANUAL  
Mobile Audio System  
PLL Synthesizer Stereo Radio  
Digital Compact Disc Player  
XM Ready Function  
Automatic Memory Storing  
Slide Down Detachable Panel  
Direct Track Access  
Program CD Tracks  
CD Changer Control  
Auxiliary Input Function  
Wired Commander Control  
 
INSTALLATION  
Notes:  
TAKE OUT SCREWS BEFORE  
INSTALLATION  
• The unit can be installed on the vehicle  
or the ships.  
Before install the unit, please remove the  
two screws.  
• Choose the mounting location where  
the unit will not interfere with the normal  
driving function of the driver.  
Take out screws before installation  
• Before finally installing the unit, connect  
the wiring temporarily and make sure  
it is all connected up properly and the  
unit and the system work properly.  
• Use only the parts included with the  
unit to ensure proper installation. The  
use of unauthorized parts can cause  
malfunctions.  
NOTE: If this unit is installed on the ship,  
you should use two pieces of plastic film  
(30mmX20mm) supplied with the unit to  
seal the two holes after remove the  
screws. And this will be waterproof.  
• Consult with your nearest dealer if  
installation requires the drilling of holes  
or other modifications of the vehicle or  
the ship.  
• Install the unit where it does not get in  
the driver’s way and cannot injure the  
passenger if there is a sudden stop,  
like an emergency stop.  
DIN FRONT-MOUNT  
Installing the unit  
• If installation angel exceeds 30¢Xfrom  
horizontal, the unit might not give its  
optimum performance.  
1
2
53  
30˚  
3
• Avoid installing the unit where it would  
be subject to high temperature, such  
as from direct sunlight, or from hot air,  
from the heater, or where it would be  
subject to dust, dirt or excessive  
vibration.  
(Fig. 1)  
1. Dashboard  
2. Holder  
After inserting the holder into the  
dashboard, select the appropriate tab  
according to the thickness of the  
dashboard material and bend them  
inwards to secure the holder in place.  
3. Screw  
3
 
INSTALLATION  
Removing the unit  
1
6
1
2
5
3
7
4
Front Panel  
OPEN button  
(Fig. 2)  
2
1. Dashboard  
2. Nut (5mm)  
3. Spring washer  
4. Screw (5x25mm)  
5. Screw  
6. Strap  
Be sure to use the strap to secure the  
back of the unit in place. The strap can  
be bent by hand to the desired angle.  
7. Plain washer  
1. Before removing the unit, press the  
OPEN button to slide down the front  
panel.  
2. Lever  
Insert the levers supplied with the unit  
into the grooves in the housing as  
shown in figure until they click. Pulling  
the levers makes it possible to remove  
the unit from the dashboard.  
4
 
USING THE DETACHABLE FRONT PANEL  
To Detach the Front Panel  
To Reinstall the Front Panel  
1. Press the OPEN button, the front panel  
1. When the panel bracket is in slide down  
position, insert the front panel into the  
panel bracket and push the front panel  
from the middle to slide it up.  
will slide down.  
Open  
Bottom  
Button  
2. When the front panel slides down,  
press the bottom button of the front  
panel upward and pull it out from the  
panel bracket.  
Bottom  
Button  
3. For safekeeping, store the front panel  
in the supplied protective case  
immediately after being removed.  
Protective Case  
Front Panel  
5
 
WIRING CONNECTION  
XM AUDIO CABLE(BLACK)  
(BLACK)  
AUDIO R IN (RED)  
AUDIO L IN (WHITE)  
XM RECEIVER CONNECTOR SOCKET (BLACK)  
WIRING REMOTE  
CONNECTOR SOCKET  
(BLACK)  
CD CHANGER  
CONNECTOR SOCKET  
FUSE  
RED RCH  
WHITE RCH  
AUX IN CABLE (YELLOW)  
ANTENNA CONNECTOR  
6
OPERATION  
CONTROL & FUNCTIONS KEYS  
1
8
6
5
2
3
4
7
This unit is a marine rated wired remote control made using a modified controller or  
similar layout. It is capable of operation specified functions on the marine AM/FM/CD  
receiver. The body, buttons, controls and display need to be UV and water-resistant.  
It includes and LCD and an illumination circuit. The flat body should be watertight and  
the circuit board clear coated.  
1 Power button  
Press the button (1) shortly to turn on/off the head unit.  
Press button (1) for more than 3 seconds, the button is operated to initial volume  
control button. When system power turns on, the volume is set to initial volume  
level.  
2 MUTE button  
In RADIO/AUX IN mode, press MUTE  
/
button (2) to activate mute function and  
“MUTE” will appear on the display. Press the button once again to release mute  
function and return the volume to the last position before it was muted.  
In CD/CDC mode, press  
again to resume play.  
/
MUTE button (2) to pause CD/CDC player. Press it  
3 VOLUME +/- buttons  
Press VOL  
/
buttons (3) to increase/decrease volume level.  
7
 
OPERATION  
4 MODE SELECTION button  
Press the MODE button (4) to step sequentially through the following sources:  
e.g. radio mode to CD mode to CDC mode to AUX in mode.  
5 BAND SELECTION button  
Press the BAND button (5) to step sequentially through the following bands: FM1,  
FM2, FM3, AM1, AM2.  
6 TRACK/SEARCH/TUNE buttons  
• STATION SELECTION (FOR RADIO OPERATION)  
Press  
/
buttons (6) shortly to activate automatic seek function. Press for  
more than 3 seconds until “MAN” appears on the display, the manual tuning  
mode is selected. If both buttons have not pressed for several seconds, they  
will return to seek tuning mode and “AUTO” appears on the display.  
• SELECT TRACKS (FOR CD OR CDC OPERATION)  
Press the  
track.  
/
buttons (6) shortly to move to the following track or the previous  
Press the  
/
buttons (6) for more than 3 seconds to activate fast forward or  
rewind of the disc. Disc play starts from when you release the button.  
7 SHIFT/SCAN button  
• SCAN (FOR RADIO OPERATION)  
Press SHIFT/SCAN button (7) to scan through strong stations in the current  
band. Radio pauses for five seconds at each strong station. At each time the  
frequency is flashing on the display. Press SHIFT/SCAN button (7) again to  
listen to current station.  
• SELECT DISC (FOR CDC OPERATION)  
During CDC operation, press SHIFT/SCAN button (7) to shift mode. And then  
“SHIFT” will appear on the display. At shift mode, press  
/
buttons (6) to  
select next disc or previous disc. If there is not any operation for several seconds,  
it will exit shift mode automatically.  
8 Liquid Crystal Display  
Exhibit the number, the current disc and the current track, and other activated  
functions on the display (8).  
8
 
INSTALLATION  
INSTALLATION HARDWARE  
HOLDER  
BASE  
REMOTE  
MOUNTING BRACKET  
X1  
X1  
X1  
SCREW (ø4X50)  
NUT  
X2  
X2  
INSTALLATION DIAGRAM  
1. First insert the hooks on the base into  
the slots of the holder to install the base  
to the holder.  
2. Select the proper object, then place the  
remote mounting bracket on the base  
and let the object go through the base  
and the mounting bracket.  
3. Align the screw holes on the holder with  
the screw holes on the base and the  
screw holes on the bracket, then use the  
two screws (ø4X50) and nuts to fix the  
bracket, the base and holder to the proper  
location.  
4. Last install the remote control to the  
holder. See below, align the four hooks  
on the holder with the four slots on the  
remote control.  
9
OPERATION  
LOCATION OF KEYS  
16  
9
11 10 17  
8
1
18  
4
15  
6
12 13 19  
20  
21 14 22  
5
23  
24  
2
3
7
25  
1. DISP  
2. AS/PS/ELAPSE  
14. M1~M6 Preset buttons  
15. LOUD/DIM  
16. CH  
/
3.  
4.  
/MUTE  
EJ  
17. CH  
18. BAND/ENTER  
19. M1 MEM (CAT )  
20. M2 PGM (CAT )  
21. M3 RPT  
22. M4 SHF  
23. M5 SCN  
5. DISC SLOT  
6. MODE  
7. OPEN  
8. LIQUIID CRYSTAL DISPLAY  
9. PWR  
10. SEL/MENU  
11. VOL  
24. M6  
25. Reset Button  
12. VOL  
13. SHIFT/SCAN/XM-MOD  
10  
 
OPERATION  
select different set mode and separately  
to press VOL button (11) or VOL  
button (12) to select your requisite as  
following order.  
GENERAL OPERATION  
SWITHCHING ON/OFF THE UNIT  
Pressing PWR button (9) to switch on or  
turn off the unit. When system power turns  
on, the system is returned to previous  
mode.  
BEEP ON/OFF  
CLOCK ON/OFF WHILE POWER OFF  
FREQ/CLOCK/NO PRI PRIORITY  
PROGRAM POWER ON VOLUME LEVEL  
USA/EUR  
12 HOURS/24 HOURS  
FACEPLATE RELEASE  
For detailed operations, please see below:  
BEEP ON/OFF  
Press OPEN button (7) to slide down the  
removable faceplate.  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/OFF  
appears, press VOL button (11) or VOL  
button (12). to select BEEP on or BEEP  
OFF. When beep on, the beep in generated  
when every button is pressed. When beep  
off, the beep is disabled when press any  
button.  
SOUND ADJUSTMENT  
Press SEL/MENU button (10) shortly to  
change audio mode through volume, bass,  
treble, balance, and fader mdoes, Press  
VOL button (11) or VOL button (12)  
to adjust the selected mode. When the  
currently displayed function has not been  
adjusted for several seconds, the mode  
shall return to volume position and display  
will return to normal radio, CD or CDC  
display.  
Program power on volume level  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/OFF  
appears, press SEL/MENU button (10)  
shortly one time to select “program power  
on volume level” mode. And then you can  
press VOL button (11) or VOL button  
(12) to select the level when the unit turns  
on.  
Volume  
Bass  
Treble  
Balance  
Fader  
Volume  
Press SEL/MENU button (10) one time.  
Adjust volume level by VOL button (11)  
or VOL button (12).  
USA/EUR  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/BEEP  
OFF appears, press SEL/MENU button  
(10) shortly two times to select “USA/EUR”  
mode. And then you can press VOL  
button (11) or VOL button (12) to select  
USA or European radio frequency spacing.  
- USA radio spacing is 200k for FM and  
10k for AM. This is the default frequency  
spacing.  
Notes:  
The unit is initially set to volume mode.  
Bass  
Press SEL/MENU button (10) two times.  
Adjust bass level by VOL button (11) or  
VOL button (12).  
Treble  
Press SEL/MENU button (10) three times.  
Adjust treble level by VOL button VOL  
button (11) or VOL button (12).  
Balance  
- European radio spacing is 50k for FM  
and 9k for AM.  
Press SEL/MENU button (10) four times.  
Adjust sound balance between left and  
right speakers by VOL button (11) or  
VOL button (12).  
CLOCK ON/OFF while power off  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/OFF  
appears, press SEL/MENU button (10)  
shortly three times to select “clock on/off  
while power off” mode. And then you can  
press VOL button (11) or VOL button  
(12) to select if the clock is to be displayed  
while power off.  
Fader  
Press SEL/MENU button (10) five times.  
Adjust sound balance between front and  
rear speakers by VOL button (11) or  
VOL button (12).  
FREQ/CLOCK/NO PRI priority  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/OFF  
appears, press SEL/MENU button (10)  
shortly four times to select  
MENU SELECTION FUNCTION  
Hold press SEL/MENU (10) for several  
seconds to enter menu select function,  
then step short press SEL/MENU (10) to  
11  
 
OPERATION  
“FREQ/CLOCK/NO PRI priority” mode.  
And then you can press VOL button (11)  
or VOL button (12) to select frequency  
priority or clock priority or no priority.  
- When select Frequency Priority:  
The frequency will appear on the unit  
all the while. Pressing DISP button (1)  
while in Frequency Priority will temporarily  
display clock and then returns to  
frequency display.  
SET THE CLOCK  
Press the DISP button (1) shortly until the  
clock is shown on the LCD display. Then  
hold down DISP button (1) until the clock  
flashes. Then press the CH button (17)  
clockwise to change hours or rotate the  
CH button (16) to change minutes.  
MUTE  
In radio/XM/AUX IN mode, press  
/MUTE button (3) to mute audio level.  
Press the button again to release mute  
function.  
- When select Clock Priority:  
The clock will appear on the unit all the  
while. Pressing DISP button (1) while in  
Clock Priority will temporarily display  
selected station frequency (in RADIO  
mode) or track number (in CD/CDC  
mode) and then returns to clock display.  
- When select No Priority:  
When the frequency appears on the unit,  
pressing DISP button (1) will display  
clock and it will not return to frequency  
display until DISP button (1) pressed  
again. When the clock appears on the  
unit, pressing DISP button (1) will display  
frequency information.  
LOUDNESS  
Press LOUD (DIM) button (15) shortly to  
reinforce the bass output and display will  
show “LOUD”. Press it again to release  
this function.  
MODE SELECTION  
Press MODE button (6) to sequence through  
primary operating modes in the following  
order: radio >XM > CD> CDC> AUX.  
If playback media (CD) is not loaded into  
mechanism, CD mode will be skipped. If  
CDC is not connected to head unit, CDC  
mode will be skipped.  
12hours/24hours  
Hold press SEL/MENU button (10) for  
several seconds, when BEEP ON/OFF  
appears, press SEL/MENU button (10)  
shortly five times to select  
If XM receiver connector is disconnected  
to XM head unit, XM mode will be skipped.  
LIQUID CRYSTAL DISPLAY  
Exhibit current frequency and activated  
functions on the display (8).  
“12hours/24hours” mode. And then you  
can press VOL button (11) or VOL  
button (12) to set 24 hours mode or 12  
hours mode.  
- When the currently displayed function  
has not been adjusted for several  
seconds, it will exit menu set mode.  
- When you have set CLOCK ON during  
power off state, LCD backlight will be  
turn on together.  
ILLUMINATION  
Press LOUD (DIM) button (15) for more  
than 2 seconds to adjust the brightness  
of the LCD display backlight.  
RESET FUNCTION  
Reset button (25) must be activated with  
either a ballpoint pen or thin metal object.  
The reset button is to be activated for the  
following reasons:  
DISPLAY INFORMATION  
When pressed quickly, the DISP button  
(1) changes the display as follows.  
- In AM/FM mode:  
- Initial installation of the unit when all  
wiring is completed.  
- All the function buttons do not operate.  
- Error symbol on the display.  
Note: If press reset button (25), the unit  
can’t work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the  
socket on the front panel.  
-> Frequency ->CLOCK ->  
- In XM mode:  
-> Channel Name -> Artist Name ->  
Song Title -> Category Name -> CLOCK  
->  
- In CD mode:  
-> CD ->CLOCK ->  
RECOVERING INITIAL VALUE  
- In CDC (or AUX) mode:  
->CDC (or AUX)->CLOCK ->  
Each display time is 5 seconds, the display  
will return to the first position after 5  
seconds.  
In radio (AM/FM) mode, press MODE  
button (6) for more than three seconds,  
the display will appear “EEP INIT”, and all  
settings recover factory value.  
12  
 
OPERATION  
until the corresponding preset button  
number appears. Repeat steps 1 and  
2 to program additional stations.  
RADIO OPERATION  
SWITCHING TO RADIO MODE  
Press MODE button (6) shortly to select  
radio mode, the radio mode appears in  
the display together with the memory  
band and frequency.  
- Quick tuning  
Select the desired band, then press one  
of the ten preset buttons (14).  
SCAN  
Press SHIFT/SCAN button (13) to set  
function to scan mode, which scanning  
to higher frequency station with receivable  
signal and keep on each station for several  
seconds.  
SELECTING THE FREQUENCY BAND  
At radio mode, press BAND/ENTER  
button (18) shortly to select the desired  
band.  
The reception band will change in the  
following order:  
FM1  
FM2  
FM3  
AM1  
AM2  
XM OPERATION  
SWITCHING TO XM MODE  
Shortly press MODE button to select XM  
mode.  
SELECTING USER-PRESET CHANNEL  
In XM mode, the XM user-preset channel  
group is toggled cyclically through the  
group by quickly pressing the BAND  
button.  
SELECTING STATION  
Press CH button (16) or CH button  
(17) shortly to activate automatic seek  
function. Press for more than 3 seconds  
until “MANUAL” appears on the display,  
the manual tuning mode is selected.  
If both buttons have not been pressed for  
several seconds, they will return to seek  
tuning mode and “AUTO” appears on the  
display.  
The channel will change in the following  
order:  
XM1  
XM2  
XM3  
AUTOMATIC MEMORY STORING &  
PRSET SCAN  
SELECTING CHANNEL UP/DOWN  
buttons to select the  
channel up or down.  
- Automatic memory storing  
Press AS/PS button (2) for serveral  
seconds, the radio searches from the  
current frequency and checks the signal  
strength until one cycle search is  
finished. And then 10 strongest stations  
are stored into the corresponding preset  
number button  
Press the CH  
/
SEARCHING SCHANNEL  
When the AS/PS button is shortly pressed,  
the unit searches for each user preset  
channel from XM1 , XM2 to XM3. When  
an available channel is detected, the  
channel will be held at that preset number  
and played about 5 seconds. After that,  
it will search for another available channel.  
- Preset Scan  
Press AS/PS button (2) shortly to scan  
all station presets saved in memory.  
DIAGNOSTIC MODE  
STATION STORING  
Press and hold AS/PS button for over 5  
seconds will enter diagnostic mode and  
display “STATE1”, then press channel  
UP/DOWN key to select each state as  
below:  
->STATE1->STATE2->STATE3->STATE4  
->STATE5->STATE6->STATE7-> STATE8  
->STATE9  
Short press AS/PS button will exit  
diagnostic mode.  
The preset buttons (14) can be used to  
store 10 stations in each band (FM 1, FM  
2, FM 3 and AM1, AM2) for convenient  
access to your favorite stations.  
- Programming stations  
1. Select the desired band, then tune  
in the station you want to store in  
memory.  
2. Press and hold one of the preset  
buttons (14) for more than 2 seconds  
13  
 
OPERATION  
STORING PRESET CHANNELS  
The preset buttons can be used to store  
channels for convenient access to your  
favorite channels.  
6.Use CH button, CH button or directly  
press numeric buttons(0-9) to select  
1s digit.  
7.Press BAND button to confirm direct  
tune. If selected a nonexistent channel,  
after the channel number was entered,  
each digit will be converted to dashes  
for 2s, then the display will return to the  
previous channel and settings.  
- Programming channels  
1.Select the desired channel you want to  
store in memory.  
2. Press and hold one of the preset buttons  
for more than 2 seconds until the  
corresponding preset button number  
appears. Repeat steps 1 and 2 to  
program additional channels.  
- Quick tuning  
CD OPERATION  
Shortly press one of the preset buttons  
to select a preset channel directly.  
SWITCHING TO CD MODE  
If there is no CD inserted in the driver:  
Gently insert the CD with the printed side  
uppermost into the CD compartment  
until you feel some resistance. The CD  
is drawn into the driver automatically.  
CD playback begins.  
MODE SELECTION  
Press XM-MOD button to switch  
CATEGORY mode, DIRECT mode, or  
NORMAL mode. Its sequence is as follows:  
Normal  
Category mode  
Direct Tune  
If a CD is already inserted in the driver:  
Keep pressing MODE button (6) shortly  
until the CD mode display appears.  
When category mode is selected, the  
CATEGORY appears on the display and  
the function is activated.  
When Category mode is released, the  
CATEGORY disappears. When Direct  
mode is engaged, “DIRECT” of  
alphanumeric display is turned on.  
Select category and tune UP/DOWN  
within selected category  
EJECTING A DISC  
Press (EJECT) button (4) to stop CD  
playing and eject the disc from the disc  
slot (5).  
PAUSING PLAYING  
Press / /MUTE button (3) to pause CD  
player. Press it again to resume play.  
Use M1 button or M2 button to select  
desired category and press BND/ENT  
button to confirm.  
SELECTING TRACKS  
Press CH button (16) or CH button  
(17) to move to the previous track or the  
following track. Track number shows on  
display.  
Hold press CH button (16) or CH  
button (17) to fast reverse or fast forward.  
Disc play starts from when you release  
the button.  
In CATEGORY mode, channels can be  
tuned by press CH button (16) or CH  
button (17) within the same category.  
How to direct tune  
Press XM-MOD to select DIRECT MODE.  
1.In direct mode, display shows “CH000”  
channel number. (Hundred Digit flashing  
on/off)  
2.Use CH button, CH button or directly  
press numeric buttons(0-9) to select  
hundred digit.  
3.Press XM-MOD button to confirm entry  
of the hundred digit and the 10s digit is  
flashing on/off.  
4.Use CH button, CH button or directly  
press numeric buttons (0-9) to select  
10s digit.  
5.Press XM-MOD button to confirm entry  
of the 10s digit and the 1s digit is flashing  
on/off.  
DIRECT TRACK ACCESS  
Pressing number buttons 0~9(14) (i.e.  
19~28) can activate DIRECT TRACK  
ACCESS according to your need. For  
example, press button (19), and “T-01”  
will be flashing on the display. Then press  
button (20), “T-12” will appear and track  
12 will be selected to play. If you don’t  
press any button when “T-01” is flashing.  
After several seconds, “T-01” doesn’t  
flash and track 1 is selected to play. If  
14  
 
OPERATION  
you select a track number that doesn’t  
belong to the current disc, “NO TR” will  
appear on the display.  
tracks to be programmed. “FULL” will  
appear on the display.  
- When the CD is played in  
programmed order by hold pressing  
PGM button (20) for several  
seconds, hold pressing it again for  
several seconds will exit PGM  
mode.  
REPEATING THE SAME TRACK  
Hold press RPT button (21) for several  
seconds to continuously repeat the same  
track. Hold press it again to stop repeat.  
- When the disc is playing in  
programmed order, hold pressing  
MEM button (19) for several  
seconds will cancel the all  
programmed content and “CLEAR”  
appears on the display.  
- If you don’t press MEM button (19)  
to carry out program setting, then  
hold press PGM button (20) for  
several seconds, “NO-PGM” will  
appear.  
PLAYING ALL TRACKS IN RANDOM  
Hold press SHF button (22) for several  
seconds to play all tracks on CD in  
random order. Hold press again to cancel  
the function.  
PREVIEWING ALL TRACKS  
Hold press SCN button (23) for several  
seconds to play first several seconds of  
each track on the current disc. Hold  
press again to stop intro and listen to  
track.  
TRACK/TIME DISPLAY  
Press AS/PS button (2) to show running  
time/remain time of track.  
PROGRAM CD TRACKS  
Use Program function to select up to 32  
tracks to play in any order. Program  
works by allowing you to select a track  
number for each spot in the playing  
sequence. A CD must be inserted and in  
CD playing mode to use Program.  
CDC OPERATION  
You can connect a CD changer to the  
unit with CDC operation version only.  
Information on handing CDs, inserting  
CDs and operating the CD changer can  
be found in the operating instructions  
supplied with your CD changer.  
- How to program CD tracks.  
1. Hold press MEM button (19) for  
several seconds to enter Program  
mode, then “PGM” stars flashing and  
“P-01” icon appear on the display.  
2. Press CH button (16) or CH button  
(17) to choose track number. For  
example, select track 6, then press  
MEM button (19) shortly to memorize  
it and “P-02” will appear on the  
SWITCHING TO CDC MODE  
Keep pressing MODE button (6) shortly  
until the CDC mode display appears.  
Playback begins with the first CD that  
the CD changer detects.  
PAUSING PLAYING  
display. So track 6 will be played first.  
Press  
/MUTE button (3) to pause  
Thus, you can also press CH  
/
CDC player. Press it again to resume  
play.  
buttons (17) and (16) to choose track  
number 10 and press MEM button  
shortly, then “P-03” will appear. So  
track 10 will be secondly played.  
Repeat these operations, and you can  
program CD tracks to your need. If  
you completed program setting, hold  
press PGM button (20) for several  
seconds to play CD in programmed  
order.  
SELECTING TRACKS  
Press CH button (16) or CH button  
(17) to move to the previous track or the  
following track. Track number shows on  
display.  
Hold press CH button (16) or CH  
button (17) to fast reverse or fast forward.  
Disc play starts from when you release  
the button.  
Note: Using Program function can  
only select up to 32 tracks to play in  
any order. When you have selected 32  
15  
 
OPERATION  
DIRECT TRACK ACCESS  
DISC NOTE  
Pressing number buttons 0~9(14) (i.e.  
19~28) can activate DIRECT TRACK  
ACCESS according to your need. For  
example, press button (19), and “T-01”  
will be flashing on the display. Then press  
button (20), “T-12” will appear and track  
12 will be selected to play. If you don’t  
press any button when “T-01” is flashing.  
After several seconds, “T-01” doesn’t flash  
and track 1 is selected to play. If you  
select a track number that doesn’t belong  
to the current disc, “NO TR” will appear  
on the display.  
A. Notes on discs:  
1.Attempting to use non-standard shape  
discs (e.g. square, start, heart) may  
damage the unit. Be sure to use round  
shape CD discs only for this unit.  
2.Do not stick paper or tape etc., onto  
the label side or the recording side of  
any discs, as it may cause a  
malfunction.  
3.Dirt, dust, scratches and warping discs  
will cause misoperation.  
B. Notes on CD-Rs (recordable  
CDs)/CD-RWs (rewritable CDs):  
1.Be sure to use discs with following  
marks only for the unit to play:  
REPEATING THE SAME TRACK  
Hold press RPT button (21) for several  
seconds to continuously repeat the same  
track. Hold press it for several seconds  
again to stop repeat.  
Recordable  
Rewritable  
PLAYING ALL TRACKS IN RANDOM  
Hold press SHF button (22) for several  
seconds to play all tracks on the current  
disc in random. Hold press it for several  
seconds again to cancel the function.  
2.The unit cannot play a CD-R and  
CD-RW that is not finalized.  
(Please refer to the manual of your  
CD-R/CD-RW recorder or CD-R/  
CD-RW software for more information  
on finalization process).  
3.Depending on the recording status,  
conditions of the disc and the  
equipment used for the recording,  
some CD-Rs/CD-RWs may not be  
played on this unit. (See *1)  
PREVIEWING ALL TRACKS  
Hold press SCN button (23) for several  
seconds to play first several seconds of  
each track on current disc. Hold press it  
again for several seconds to stop intro  
scan and listen to track.  
*1: To have more reliable play back,  
please see following  
TRACK/TIME DISPLAY  
Press AS/PS (ELAPSE) button (2) to show  
running time of track.  
recommendations:  
a.Use CD-RWs with speed 1x to 4x  
and write with speed 1x to 2x.  
b.Use CD-Rs with speed 1x to 8x and  
write with speed 1x to 2x.  
c.Do not play a CD-RW which has  
been written for more than 5 times.  
SELECTING DISC  
Press SHIFT/SCAN button (13) to shift  
mode and then “SHIFT” will appear on  
the display. At shift mode, press CH  
button (16) or CH button (17) to select  
previous disc or next disc. If there isn’t  
any operation for several seconds, it will  
exit shift mode automatically. At shift  
mode, you can also press number button  
0~9 (14) (i.e. 19~28) to select the disc  
directly. If you select 3# disc (press button  
(21), and there isn’t a disc in the 3# slot,  
“NO CD” will appear.  
16  
 
SPECIFICATION  
GENERAL  
Power Supply Requirements  
Chassis Dimensions  
Tone Controls  
: DC 12 Volts, Negative Ground  
: 178 (W) x 178 (D) x 50 (H) mm  
- Bass (at 100 Hz)  
- Treble (at 10 KHz)  
Maximum Output Power  
Current Drain  
:
:
10 dB  
10 dB  
: 4 x 50 Watts  
: 15 Ampere (max.)  
CD PLAYER  
Signal to Noise Ratio  
Channel Separation  
Frequency Response  
: More than 60 dB  
: More than 50 dB  
: 40 Hz - 18 KHz  
RADIO  
FM  
Frequency Coverage  
IF  
Sensitivity (S/N = 30 dB)  
Stereo Separation  
: 87.5 to 107.9 MHz  
: 10.7 MHz  
: 3 µV  
: > 30 dB  
AM  
Frequency Coverage  
IF  
Sensitivity (S/N = 20 dB)  
: 530 to 1720 KHz  
: 450 KHz  
: 32 dBu  
17  
 
TROUBLE SHOOTING  
Before going through the check list, check wiring connection. If any of the problems  
persist after check list has been made, consult your nearest service dealer.  
Symptom  
No power.  
Cause  
Solution  
The car ignition switch is  
not on.  
If the power supply is  
connected to the car accessory  
circuits, but the engine is not  
moving, switch the ignition key  
to “ACC”.  
The fuse is blown.  
Replace the fuse.  
Disc cannot be  
loaded or ejected. the player.  
Presence of CD disc inside Remove the disc in the player,  
then put a new one.  
Inserting the disc in reverse Insert the compact disc with  
direction. the label facing upward.  
Compact disc is extremely Clean the disc or try to play a  
dirty or defective disc. new one.  
Temperature inside the car Cool off or until the ambient  
is too high.  
temperature return to normal.  
Condensation.  
Leave the player off for an hour  
or so, then try again.  
No sound.  
Volume is in minimum.  
Adjust volume to a desired level.  
Check wiring connection.  
Wiring is not properly  
connected.  
Sound skips.  
The installation angle is  
more than 30 degrees.  
Adjust the installation angle less  
than 30 degrees.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
The operation keys The built-in microcomputer Press the RESET button.  
do not work.  
is not operating properly  
due to noise.  
Front panel is not properly fixed  
into its place.  
The radio does not The antenna cable is not  
Insert the antenna cable firmly.  
work. The radio  
station automatic  
selection does not The signals are too weak.  
work.  
connected.  
Select a station manually.  
88-C1802-17  
18  
 

Philips Computer Drive 9305 125 24775 User Manual
Philips Iron GC4444 User Manual
Philips Portable CD Player AX3217 17B User Manual
Pioneer Car Satellite Radio System GEX P910XM User Manual
Pioneer Stereo Amplifier PRS D1100M User Manual
Poulan Brush Cutter 530164264 User Manual
Poulan Chainsaw 952802143 User Manual
Pride Mobility Mobility Aid Jazzy 1103 User Manual
ProForm Home Gym 831288070 User Manual
Proxima ASA Projector 4100 4200 User Manual