Panasonic Network Card MAYS0750Z User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Zener Diodes  
M
A
Y
S0750Z  
Silicon planar type  
For surge absorption circuits  
Unit: mm  
+0.05  
–0.03  
0.60  
+0.05  
+0.05  
Features  
0.12  
0.80  
–0.02  
–0.03  
Small terminal capacitance Ct  
High electrostatic discharge ESD  
1
0.01±0.01  
Absolute Maximum Ratings T
a
= 25
°
C  
Parameter  
Symbol  
Rating  
150  
Unit  
mW  
°
C  
2
0.30±0.05  
+0  
1
0
Total power dissipation
*  
PT  
Tj  
–0.05  
5°  
Junction temperature  
Storage temperature  
150  
T
stg  
55 to +150  
±12  
°
C  
2
Electrostatic discharge
*  
ESD  
kV  
Note) 1: P = 150 mW achieved with a printed circuit board.  
*
T
2: Test method: IEC61000-4-2  
*
1: Anode  
(C = 150 pF, R = 330 , Contact discharge: 10 times)  
2: Cathode  
EIAJ: SC-79  
SSMini2-F1 Package  
Marking Symbol: CZ  
Electrical Characteristics T
a
= 25
°
C±3
°
C  
Parameter  
Breakdown voltage
*  
Symbol  
VBR  
IR  
Conditions  
Min  
Typ  
Max  
Unit  
V
I
R
= 1 mA  
6.0  
7.5  
Reverse current  
V
R
= 5 V  
2
µA  
pF  
Terminal capacitance  
Ct  
IR = 0 V, f = 1 MHz  
1.5  
3.0  
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.  
2. : V guaranted 20 ms after current flow.  
*
Z
Publication date: May 2005  
SKE00023AED  
1
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Multiquip Automobile Parts C 30HDNI User Manual
Multiquip Outboard Motor CV1A User Manual
NEC Car Video System x461s User Manual
NEC Server set810 User Manual
Nordyne Furnace G6RC 90+ User Manual
Nortel Networks Fax Machine P0941753 02 User Manual
Panasonic Computer Drive LF 1004AB User Manual
Panasonic Electric Shaver ES3831 User Manual
Panasonic PDAs Smartphones CF P1Series User Manual
Parkside Saw PHKS 1300 A1 User Manual