Using remote controller
Overview
The RC-482M/480M remote controller is a useful tool that can not
only operate the TX-SR700/700E/600/600E, but also all the other
components of your home theater as well. To operate any
component, first press the Mode button on the remote controller that
corresponds to the component that you wish to control. Then simply
press the desired operation button and the component will operate
accordingly. For example, if you wish to select the CD input source
at the TX-SR700/700E/600/600E with the remote controller, first
press the RCVR MODE button to select the TX-SR700/700E/600/
600E and then press the CD (INPUT SELECTOR) button.
*
Diagram for RC-482M
Calling up a preset radio station
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
RCVR MODE
CH
2. Press the TUN input selector button.
3. Press the desired operation button.
Operation buttons:
VOL
CH
: Selects the desired preset station number
MUTING
You may also use the following buttons:
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
TUN
Controlling an Onkyo cassette tape deck
The
connector of the Onkyo cassette tape deck must be
connected to the TX-SR700/700E/600/600E (see page 29).
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
2. Press the desired operation button.
RCVR MODE
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Onkyo cassette tape deck.
Operation buttons:
VOL
: Play
: Stop
MUTING
: Rewind
TAPE
operation
buttons
: Fast forward
: Skips to beginning of next track during playback
: Skips to beginning of current track during playback
REC: Record/Pause
: Reverse playback
You may also use the following buttons:
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
Note:
Even for devices with the
and
buttons, signal discrepancies
may cause them not to work properly.
63
Using remote controller
Controlling an Onkyo DVD player
The
connector of the Onkyo DVD player must be connected to
the TX-SR700/700E/600/600E (see page 29).
1. Press the DVD MODE button.
The DVD MODE button lights green.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Onkyo DVD player.
Operation buttons:
ON: Turns DVD player on and off
STANDBY: Turns DVD player off (Some sets may not respond to
this button. In this case, use the ON button to put the DVD player in
the standby state.)
SETUP: Displays OSD Menu of the DVD player
ON
STANDBY
: Moves cursor in the OSD Menu of the DVD player
ENTER: Enter button for the OSD Menu of the DVD player
RETURN: Return button for the OSD Menu of the DVD player
DVD MODE
RETURN
ENTER,
SETUP
VOL
TOP MENU or MENU: Displays menu screens recorded on DVD
media
DISC
DISC
: Selects disc in DVD changer
AUDIO SEL: Selects audio or language track (if recorded on the
DVD)
TOP MENU
AUDIO SEL
MENU
MUTING
ANGLE: Selects camera angle (if recorded on the DVD)
ANGLE
SUBTITLE
SUBTITLE: Selects subtitle language (if recorded on the DVD)
DVD
operation
buttons
SEARCH: Searches for location on disc to start playback
RANDOM: Random playback
: Chapter/Track down
: Chapter/Track up
: Play
Numeric keys
SEARCH
: Stop
: Fast reverse
: Fast forward
: Pause
OPEN/CLOSE : Opens/closes disc tray
0, 1 to 9, +10: Numeric keys
You may also use the following buttons:
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
Note:
When operating an Onkyo DVD player directly with the remote
controller without connecting the
terminals, pre-programming is
necessary (see page 67).
65
Using remote controller
Controlling an Onkyo MD recorder
The
conneÇóctor of the Onkyo MD recorder must be connected
to the TX-SR700/700E/600/600E (see page 29).
1. Press the MD MODE button.
The MD MODE button lights green.
2. Press the desired operation button.
ON
STANDBY
MD MODE
The buttons shaded in the figure to the left are the operation
buttons that can be used to control an Onkyo MD recorder.
Operation buttons:
ON: Turns on and off MD player (same as the STANDBY button on
the remote controller)
VOL
: Track down
: Track up
MUTING
: Play
: Stop
MD
operation
buttons
: Skip backward
: Skip forward
REC: Record
: Pause
: Eject
1 to 9, 0, --/---: Numeric keys
ENTER: Enters settings
Numeric keys
ENTER
You may also use the following buttons:
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
VCR and TV MODE buttons
No preset codes are programmed into the VCR and TV MODE
buttons. Therefore you can use these buttons to program the remote
controller signals of other devices.
There are two methods. One method is selecting the name of a
different brand from the table, entering the setting number listed, and
calling up the pre-programming code (see page 67). The other
method is sending the commands from the other brand’s remote
control directly into this remote controller (see page 70).
TV MODE
TV
VCR MODE
VCR
When in the VCR and TV mode, you may use the following buttons:
VOL
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
MUTING
TV : Turns on and off the television
(and switches to the TV mode)
VCR : Turns on and off the VCR
(and switches to the VCR mode)
66
Entering a pre-programming code
The remote controller has three learning functions. One is entering
Learning a pre-programming code
the pre-programmed code for a remote controller of another
manufacturer. Another is the normal learning function that enables
the remote controller to learn the codes directly from other remote
controllers (see page 70). And the last is a macro learning function
that enables you to program a series of operations into the remote
controller so that the operations can all be performed at once by
pressing one button (see page 73).
By entering a pre-programming code, you can have the RC-482M/
480M remote controller operate a component made by another
manufacturer. The buttons that are used for operation are given on
the next page.
1. Find the 3-digit number listed for the manufacturer
name of the component that you want to operate in the
table on the next page.
2. Turn on the component that you want to operate (i.e.
DVD, satellite tuner, or television).
SEND/LEARN
indicator
3. While holding down the MODE button on the RC-482M/
480M that you want to program, press the DISPLAY
button, and then release both buttons.
Buttons that
can be pre-
programmed
The SEND/LEARN indicator lights when the MODE button is
pressed and turns off when the DISPLAY button is pressed.
When the indicator turns off, release both buttons. The SEND/
LEARN indicator lights again.
VOL
4. Within 30 seconds, enter the 3-digit code number.
The SEND/LEARN indicator slowly flashes twice. If the SEND/
LEARN indicator quickly flashes three times, then either a
mistaken 3-digit code was entered or an incorrect operation was
performed. If this occurs, return to step 3.
5. Press the button that you programmed and check if
the system operates correctly.
• If the component does not operate properly, return to step 3
and repeat the steps above.
• If it still does not operate properly, program the command
directly from the other remote controller normally (see page
70).
Numeric keys
DISPLAY
When entering the code of Onkyo DVD players:
There are three SETTING numbers. Choose the SETTING number
according to how you will be using the DVD player.
No. 601/613: These codes are for operating the Onkyo DVD player
by pointing the remote controller directly at it, either because it does
Caution:
With some brand’s components, some buttons may not work
correctly. In this case, program the command directly from the other
remote controller normally (see page 70).
not have an
terminal, or it does but you are not connecting it with
an
cable. First enter 601 and if it does not operate properly, enter
613.
No. 600: This code is for Onkyo DVD players that have an
terminal that you are connecting to the TX-SR700/700E/600/600E
with an
cable. You will then operate the DVD player by pointing
the remote controller at the remote control sensor on the TX-SR700/
700E/600/600E. You do not need to enter this code because it is
factory preset. However, if the code has been changed to 601 or 613,
then you will need to change it back to 600.
67
Entering a pre-programming code
RCA
SABA
SAMSUNG
382
383
PHILIPS
152, 162, 191
192, 193
194
195
196
Pre-programming codes
PIONEER
PROSCAN
QUASAR
RADIO SHACK
RCA
384, 385, 386, 387,
388, 389, 390
391, 392, 393
394
Note:
If more than one code is given in the table,
try each code one by one until you reach a
code that works (i.e. if the first code does
not work, then try the next).
SANYO
SCOTT
SELECO
SHARP
SHINTOM
SIEMENS
SONY
110, 141, 197, 198,
199, 200
395
396, 397, 398, 399
400
401
402, 403, 404, 405,
406, 407, 408, 409,
410, 411, 412, 413,
423
414
414, 415
416, 417
418, 419, 420
SABA
SAMSUNG
182, 183, 201
202, 203, 204, 205,
206, 207, 208
209, 210, 211, 212
103
213
214, 215
216, 217
218, 219, 220, 221,
222, 223
224, 225
201, 226, 227
228
213, 229
230
DVD
BRAND
SETTING No.
602, 609
603
SANYO
SCHNEIDER
SEARS
SELECO
SHARP
DENON
HITACHI
JVC
604
KENWOOD
MAGNAVOX
MARANTZ
MITSUBISHI
ONKYO
PANASONIC
PIONEER
PROSCAN
RCA
605
606, 613
607
608, 613
600, 601, 613
609
610
611
611
SYMPHONIC
TEKNIKA
TELEFUNKEN
TOSHIBA
WHITE
WESTINGHOUSE
WATSON
SONY
SYMPHONIC
TELEFUNKEN
THOMSON
TOSHIBA
UNIVERSUM
ZENITH
333
421
422
ZENITH
231, 232
SONY
612
TOSHIBA
YAMAHA
ZENITH
613
609, 614
613, 615
TV
BRAND
SETTING No.
100, 101
102, 103, 104
105
106
107
108, 109
110
111, 112, 113
114
115, 116
117, 118, 119, 120,
121
AIWA
AKAI
AUDIOSONIC
BELL & HOWELL
BLAUPUNKT
BRIONVEGA
CENTURION
COLTINA
CORONAD
CROWN
DAEWOO
VCR
BRAND
AIWA
AKAI
SETTING No.
300, 301, 302
303, 304, 305, 306,
307
308
309
310
311, 312, 313
BAIRD
BELL & HOWELL
BLAUPUNKT
CGM
COLTINA
DAEWOO
DIGITAL
314
315, 316
317
DUAL
EMERSON
122
123, 124, 125, 126,
127
EMERSON
318, 319, 320, 321,
FENNER
FERGUSON
FISHER
128, 129
130, 131
132
322
323
FENNER
FISHER
324, 325, 326, 327
FUNAI
133, 134, 135
FUJITSU GENERAL 136, 137, 138
FUJITSU GENERAL 328
GE
139, 140, 141
142, 143
144
145, 146
147, 148, 149, 150
151
FUNAI
GE
329
330, 331
332, 336, 337
333, 334
335
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
HYPER
INNO HIT
IRRADIO
JVC
GO VIDEO
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
338
152
103
331, 339, 340, 341,
382
342, 343, 344, 345,
346, 347, 348, 349,
350
153, 154, 155, 156,
157
158
JVC
KENDO
KTV
LUXOR
MAGNAVOX
MARANTZ
MARK
159, 160
161
162, 163
164
LOEWE
MAGNAVOX
MITSUBISHI
351, 352
353, 354, 355
356, 357, 358, 359,
360, 361, 362, 363,
364
165
MATSUI
MITSUBISHI
MIVAR
NEC
NOKIA
OCEANIC
NORDMENDE
OKANO
ORION
PANASONIC
166, 167, 168, 169
170, 171, 172, 173
174, 175
176, 177
178, 179, 180, 181
181
182, 183
152
184, 185, 186
187, 188, 189, 190
NEC
NOKIA
NORDMENDE
OKANO
ORION
365, 366, 367
313
368, 369, 370
371, 372
319, 373
374, 375, 376, 377,
378
353, 379, 380
311
381
PANASONIC
PHILIPS
PHONOLA
PIONEER
68
Operating your programmed remote controller
After entering a pre-programming by following the procedure
given above, the following modes become enabled for use.
DVD MODE (DVD Player Mode)
Operations are the same as explained on page 65.
VCR MODE (VCR Mode)
1. Press the VCR MODE button.
The VCR button lights green.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your VCR.
VCR MODE
VCR
The buttons given below have operations programmed
into them.
VCR : Turns on and off the VCR (and switches to the VCR mode)
CH
VOL
CH
: Changes selected preset channel
TV/VCR: Switches VCR input setting
TV/VCR
MUTING
: Play
: Stop
Video cassette
recorder
: Rewind
operation
buttons
: Fast Forward
: Pause
0, 1 to 9, +10: Numeric keys
You may also use the following buttons:
Numeric keys
VOL : Adjusts volume at TX-SR700/700E/600/600E
MUTING: Activates muting function at TX-SR700/700E/600/
600E
TV MODE (TV Mode)
1. Press the TV MODE button.
The TV button lights green.
2. Press the desired operation button.
The buttons shaded in the figure to the left are the operation
buttons that can be used to control your television.
TV MODE
TV
The buttons given below have operations programmed
into them.
TV : Turns on and off the television (and switches to the TV mode)
CH
VOL
CH
: Changes television channel
TV/VCR: Switches television input setting
0, 1 to 9, +10: Numeric keys
TV/VCR
MUTING
ENTER: Confirm
VOL : Adjusts volume at television
MUTING: Activates muting function at television
Numeric keys
ENTER
69
Programming the commands of remote controllers for
other devices into the remote controller
Programming procedure
S
E
U M
O
L
When programming the commands of another remote controller to
V
G
T I N
U
the RC-482M/480M remote controller, you must first decide under
E
T
N
O
T
S
E
T
L
E
S
which MODE button you want the commands to be linked. In
general, you will select the MODE button that corresponds to the
component you are programming. For example, if you are
programming the functions from a remote controller for a compact
disc player, you would choose the CD MODE button. Then, by
pressing the CD MODE button, the buttons on the RC-482M/480M
remote controller will change to the commands you program here to
operate the compact disc player.
H
C
T
E
E S
D
R
E
C
D
V
P
R
E
N
U
D
H
T
U
O
P
T
T I - C
N
L
I N
M
O
U
H
U
P
R
O
R
O
E
R
T
G
D
R
C
O
E
N
U
C
M
L E
S U
- 2
I S
E
O
D
T
E
C
D
R
T
S
E
U
M
V I D
P
I M
I N P
A
D
- 1
T
O
E
P
I D
V
E E
L
D
S
V
D
R
E
W
O
P
After programming which MODE button to use, you will then
transfer the separate commands from the other remote controller
over to the RC-482M/480M remote controller one at a time. Each
command is then programmed to a different button on the RC-
482M/480M remote controller. Any button is programmable for this
step except for the six MODE buttons (RCVR, CD, DVD, MD, TV,
and VCR), the two MACRO buttons (MACRO 1 and 2), and the
LIGHT button (RC-482M only).
2 to 6 inches
(5 to 15 cm )
Even after the commands have been memorized, keep your old
remote controller in a safe place. If for some reason the commands
are lost (e.g., when the batteries run down), it will be necessary to
memorize them once again.
1. Place the remote controller and the remote controller
for the other device facing each other at a distance of 2
to 6 inches (5 to 15 cm) apart.
2. While pressing and holding down the desired MODE
button on the remote controller, press the ENTER
button and then release both buttons.
The SEND/LEARN indicator lights when the MODE button is
pressed and turns off when the ENTER button is pressed. When
the indicator turns off, release both buttons. The SEND/LEARN
indicator lights again.
SEND/LEARN
indicator
3. Press and release the button on the remote controller
to which you want to transfer the next command.
You may select any button excluding the eleven ones indicated
in the figure below. When you press the button, the SEND/
LEARN indicator turns off. When you release the button, the
indicator lights again.
MODE
buttons
If you press the wrong button by mistake, press that same button
again. The SEND/LEARN indicator flashes twice, and the
remote controller exits the programming mode.
LIGHT
(RC-482M only)
MACRO 1
MACRO 2
MODE buttons
ENTER
:
Buttons that cannot be programmed.
70
Programming the commands of remote controllers for other devices into the remote
controller
4. Press and hold down the button (that corresponds to
the command you are programming) on the remote
controller of the other device until the SEND/LEARN
lamp on the remote controller flashes twice.
After flashing twice, the SEND/LEARN indicator will light
again.
5. Repeat Steps 3 and 4 to transfer all the commands you
desire from the other remote controller and program
them to buttons on the remote controller under the
same MODE.
Repeat Steps 2 through 4 to program commands to a different
MODE (e.g., when programming from a different remote
controller).
6. Press the MODE button that you pressed in step 2 to
complete the programming.
7. Operate the newly programmed buttons to make sure
the learning function was performed properly.
Notes:
• The remote controller codes for Onkyo compact disc players,
cassette tape decks, DVD players, and mini disc recorder have
already been programmed into buttons on the remote controller.
You may, however, use these buttons to program the codes for
other remote controllers. If you wish to restore the Onkyo preset
codes after you program new codes, you must first erase the new
codes (see page 72).
• The remote controller has 318 memory slots (6 modes × 53
buttons). Some remote controllers may have more commands
that can be remembered by the remote controller. In such cases,
it will be necessary for you to determine which commands are
more important than others.
• If the SEND/LEARN indicator quickly flashes three times and
turns off, then the remote controller has exited the programming
mode because either you have made a mistake during
programming or a time-out has occurred because no button has
been pressed. Resume from Step 2.
• If you try to program beyond the learning capacity of the remote
controller, the SEND/LEARN indicator flashes six times
quickly, and the remote controller exits the programming mode.
Try programming under a different MODE button.
• When you want to program a command to a button to which you
have already programmed a command, simply follow the same
procedure given and the previous programming for that button
will be overwritten.
• The remote controller uses infrared rays to send its commands,
as do most other remote controllers. Though most remote
controller codes can be memorized by the remote controller, be
aware that some remote controllers use systems that are quite
different from the remote controller and therefore may not be
able to be programmed.
• Some remote controllers have a single button that performs
multiple functions (for example, the function may change each
time the button is pressed). If this is the case, each function must
be programmed to a separate button on the remote controller.
• Once you have transferred the commands from the other remote
controller, refer to the instruction manual that came with that
product for instructions on how to operate that product.
• Make sure both the remote controller and the other remote
controller have new batteries. If either of them has batteries that
are low, you may not be able to program the commands of the
other remote controller properly into the remote controller.
See page 72 for how to erase the memorized commands from all
buttons.
71
Programming the commands of remote controllers for other devices into the remote
controller
Erasing the programmed command from one
button
SEND/LEARN
indicator
You can only erase memorized commands and not preset ones.
1. Press and hold down the MODE button for the command,
press the ENTER button, and then release both
buttons.
When you press the MODE button, the SEND/LEARN indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp lights again.
MODE
buttons
2. Press and release the button for the command you
wish to erase.
When you press the button, the SEND/LEARN indicator turns
off. When you release the button, the lamp lights again.
3. Press and release the same button again.
The SEND/LEARN lamp slowly flashes twice. The memorized
command is erased.
Note:
If the SEND/LEARN indicator quickly flashes three times and turns
off, then the remote controller has exited the erasing mode because
either you have made a mistake during erasing or a time-out has
occurred because no button has been pressed. Resume from Step 1.
ENTER
Erasing all the commands programmed under a
MODE button
SEND/LEARN
indicator
1. Press and hold down the desired MODE button, press
the ENTER button twice, and then release both
buttons.
When you press the MODE button, the SEND/LEARN indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp slowly flashes twice and
then lights again.
MODE
buttons
2. Press and release the same MODE button again.
When you release the button, the SEND/LEARN indicator
slowly flashes twice. This erases all the commands memorized
to the MODE button.
Notes:
• If the SEND/LEARN indicator quickly flashes three times and
turns off, then the remote controller has exited the erasing mode
because either you have made a mistake during erasing or a time-
out has occurred because no button has been pressed. Resume
from Step 1.
• If many commands have been programmed to the MODE
button, then the SEND/LEARN indicator may remain lit for up
to 20 seconds during Step 2. This is not a malfunction.
ENTER
72
Using the macro function
Programming the macro
What is the macro function?
A macro function enables you to program a series of button
operations (up to 16) on the remote controller into a single button.
The series of operations are then called a macro. For example, to
play a compact disc player connected to the TX-SR700/700E/600/
600E normally, you must perform the following steps:
With the macro function, you can program a series of button
operations as a macro into the MACRO button so the macro can be
executed with just one touch. Note that for the macro function, only
one macro can be programmed. For example, to program the macro
described above on this page for the MACRO button, perform the
steps given below.
1. Press the RCVR MODE button.
2. Press the ON button.
1. Press and hold down any one of the six MODE
buttons, press the MACRO 1 (or 2) button, and then
release both buttons.
3. Press the CD (INPUT SELECTOR) button.
4. Press the CD MODE button.
5. Press the playback ( ) button.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the MACRO 1
(or 2) button, the indicator turns off. When you release the
buttons, the indicator flashes briefly and then lights again.
2. Press the operation buttons you wish to program in
By using the macro function, you can perform the above five
operations by only pressing one button.
order (in this case, press RCVR MODE → ON → CD
(INPUT SELECTOR) → CD MODE → playback (
)
button).
When you press each button, the SEND/LEARN indicator turns
off. When you release the button, the indicator lights.
SEND/LEARN
indicator
3. Press the MACRO 1 (or 2) button to complete the
procedure.
ON
The SEND/LEARN indicator slowly flashes twice.
MACRO 1
RCVR MODE
MACRO 2
4. Check to see if the macro has been properly programmed.
MODE buttons
Notes:
CD MODE
• You may program up to 16 button operations into the macro
function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
• If the SEND/LEARN indicator quickly flashes three times and
turns off, then the remote controller has exited the programming
mode because either you have made a mistake during
programming or a time-out has occurred because no button has
been pressed. Resume from Step 1.
(CD playback)
CD
(INPUT
SELECTOR)
Executing the macro
Perform the procedure below to execute the macro that you have
programmed into the remote controller. After programming the
macro, you should always run it at least once to make sure that it has
been programmed properly.
Point the remote controller at the TX-SR700/700E/600/
600E and press the MACRO 1 (or 2) button.
It may take a while for the macro to finish transmitting, so be sure to
continue pointing the remote controller at the device until the SEND/
LEARN indicator turns off.
Tips:
• If you erase or change the command of a button programmed in
the macro, that operation of that button will no longer work in
the macro. In this case, it will be necessary for you to reprogram
the macro in order to avoid incorrect operation.
• The codes programmed into the macro will be transmitted at an
interval of 0.5 seconds. However, some devices may not be able
to complete one operation in 0.5 seconds and may miss the next
code. In this case, after pressing one operation button, you can
press the same MODE button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
73
Using the macro function
Erasing a macro from the MACRO 1 (or 2) button
SEND/LEARN
indicator
1. Press and hold down any one of the six MODE
buttons, press the MACRO 1 (or 2) button, and then
release both buttons.
When you press the MODE button, it lights green and the
SEND/LEARN indicator lights. When you press the MACRO 1
(or 2) button, the indicator turns off. When you release the
buttons, the indicator flashes once.
MACRO 1
MACRO 2
MODE buttons
2. Press the MACRO 1 (or 2) button again.
The SEND/LEARN indicator slowly flashes twice. The macro
programmed to the MACRO button is erased.
Notes:
• If the SEND/LEARN indicator quickly flashes three times and
turns off, then the remote controller has exited the erasing mode
because either you have made a mistake during erasing or a time-
out has occurred because no button has been pressed. Resume
from Step 1.
• If you press a button other than MACRO 1 (or 2) button in Step
2, then you will in effect be overwriting the previous macro with
a new macro.
ENTER
Erasing all commands and macros that have
been programmed
SEND/LEARN
indicator
This procedure will erase all the commands and macros that you
have programmed into the remote controller and return it to its
default settings. This operation will not affect the preset settings of
the remote controller.
ON
STANDBY
1. Open the battery cover and remove the batteries from
the remote controller.
2. While pressing and holding down the ON and
STANDBY buttons, re-insert the batteries in their
correct orientation, and then release both buttons.
The SEND/LEARN indicator flashes slowly.
3. Press the ENTER button.
The SEND/LEARN indicator lights up for about ten seconds and
then turns off.
All programmed commands and macros are erased and the remote
controller returns to its factory presets.
Notes:
• Proceed to Step 3 immediately after Step 2; otherwise, the
batteries will be consumed quickly.
• If you press any button other than the ENTER button in Step 3,
nothing will be erased. In this case, resume from Step 1.
ENTER
74
|