URC 7200 / 7201
Cinema 7
User Manual
3.
4.
Enter the first four-digit Cassette Player code
listed for your brand in the “Setup Codes For
Audio Cassettes” section. If you perform this
procedure correctly, the red light will blink twice
when you enter the final digit of your code.
Amplifier does not respond, repeat steps 2-4,
trying each code listed for your brand until you
find the one that operates your Amplifier.
Remember, if you want to use your Cinema 7 to operate
Locate the brand name of your CD Player in the “Setup
Codes For CD Players” section. The brands are listed in
alphabetical order with the most popular codes listed
first. You will use one of these codes to program your
Cinema 7 to operate your CD Player.
The PREV CH (Previous Channel) key
operates the same as the Last Channel or
Recall key on your original remote. The PREV
CH key also controls the following functions in
other modes: DVD/LD, RCVR, AUX and CD
mode = Random.
functions in other modes: DVD/LD mode =
PREV CH
your VCR, press the VCR key first.
Angle, CBL/SAT mode = Next.
NOTE: If your TV/VCR is working on one of the above
codes highlighted with an asterisk (*), you may need to
program a separate TV code in order to control the volume.
Check the list of codes below and follow the instructions
detailed in the “Programming the Cinema 7 to Operate
Your TV” section to program the supplied TV code.
TV/VCRs working on VCR code 0032 may require
TV code 0000 for volume control.
The SURROUND key operates the same as the
Surround On/Off key on your original remote.
The SURROUND key also controls the following
functions in other modes: VCR mode = Auto
Tracking, DVD/LD mode = Disc, CBL/SAT mode
= Favorite Channel, CD mode = 10+.
SURROUND
5.
Your Cinema 7 is now programmed to operate
your Amplifier. Write your Amplifier code in the
boxes to the left for future reference.
Aim the Cinema 7 at your Cassette Player and
press PL (Play). Your Cassette Player
should play your tape. If your Cassette Player
does not respond, repeat steps 2-4, trying
each code listed for your brand until you find
the one that operates your Cassette Player.
To program the Cinema 7 to operate your CD Player:
PL
1.
Turn on your CD Player and insert a disc.
FEATURES AND FUNCTIONS
CH
CH
The CH L/L, VOL L/L, MUTE, PREV CH
and Digit (0-9) keys are made of a phospho-
rescent material that glows-in-the-dark.
Expose the keys to bright light to activate the
glow-in-the-dark feature. The length of time the
keys remain illuminated will be determined by
the length of time the remote is exposed to
bright light.
2.
CD
Press CD and release. Press and hold MAGIC
until the Cinema 7’s red light blinks twice, then
release MAGIC.
Remember, if you want to use your Cinema 7 to operate
your Amplifier, press the AUX key first.
Here are the features and functions of the Cinema 7
universal remote control. Use the drawing to locate each
feature of the remote, then refer to the chart for a descrip-
tion of what function each feature performs.
MAGIC
The MACRO and MACRO2 keys can
MACRO
MACRO 2
memorize up to 15 keystrokes per key that can
be accessed in sequence with a single key
press. These keys are not mode specific.
VOL
VOL
TV/VCRs working on VCR code 0035 may require
TV code 0051 for volume control.
3.
4.
Enter the first four-digit CD Player code listed
for your brand in the “Setup Codes For CD
Players” section. If you perform this procedure
correctly, the red light will blink twice when you
enter the final digit of your code.
SEARCHING FOR YOUR CODE
5.
Your Cinema 7 is now programmed to operate
your Cassette Player. Remember, if you want
to use your Cinema 7 to operate your Cassette
Player, press the VCR key first.
TV/VCRs working on VCR code 0048 may require
TV code 0093 for volume control.
If your TV, VCR or Cable Converter does not respond to
the Cinema 7 after trying all of the codes listed for your
brand, or if your brand is not listed at all, try searching for
your code. For example, after trying all of the codes for
your TV, you still cannot get the Cinema 7 to operate your
TV, then:
MUTE
TV/VCRs working on VCR code 0060 may require
TV code 0047 for volume control.
INSTALLING THE BATTERIES
PREV CH
Your Cinema 7 requires four (4) new AAA alkaline
TV/VCRs working on VCR code 0081 may require
TV code 0054 for volume control.
RE-ASSIGNING DEVICE KEYS
0 - 9
Aim the Cinema 7 at your CD Player and press
PL (Play). Your CD Player should play your
disc. If your CD Player does not respond,
repeat steps 2-4, trying each code listed for
your brand until you find the one that operates
your CD Player.
PL
batteries. To install the batteries:
You can use the Cinema 7 to operate a second TV or a
second VCR or any combination of seven home entertain-
ment components. For example, you may want your
Cinema 7 to control 1 TV, 1 Cable Converter, 1 Receiver, 1
CD Player, 1 DVD Player and 2 VCRs. To accomplish this,
you must re-assign one of the device keys to operate the
desired component, in this case, a second VCR. The chart
below shows you how to re-assign a particular device key
and then set up your new component.
1.
On the back of the Cinema 7, pull back on the tab
TV/VCRs working on VCR code 0162 may require
TV code 0250 for volume control.
The SLEEP key accesses the Sleep Timer of
your home entertainment components (TV,
CABLE/SAT, RCVR and AUX modes only).
Even if your component does not have a Sleep
Timer, the Cinema 7 may access its own built-
in sleep timer.
1.
Turn on your TV.
SLEEP
and lift the battery cover off.
TV
TV/VCRs working on VCR code 0278 may require
TV code 0451 for volume control.
2.
Press TV and release. Press and hold MAGIC
until the Cinema 7’s red light blinks twice, then
release MAGIC.
2.
Match the + and - marks on the batteries to the +
and - marks in the battery case, then insert the
batteries.
MAGIC
5.
Your Cinema 7 is now programmed to operate
your CD Player. Write your CD Player code in
the boxes to the left for future reference.
Programming the Cinema 7 to operate your DVD or
Laser Disc Player:
Locate the brand name of your DVD or Laser Disc Player
and then write it in the space below.
3.
4.
Press 9 - 9 - 1.
9 - 9 - 1
3.
4.
Press the battery cover back into place.
The REW (Rewind), PL (PLAY), FF (Fast
Forward) REC (Record), STOP, and PAUSE
keys operate the same as the transport keys
on your original VCR, Laser Disc, DVD and CD
Player remote. As a safety feature of the
Cinema 7, you must press the REC key twice
before recording.
REW
PL
POWER
Slowly alternate between pressing POWER*
and TV until your TV turns OFF. Make sure that
the Cinema 7 is aimed at your TV during the
search. You may have to press this sequence
of buttons (POWER* then TV) up to 100 times
to search the entire library of codes.
TV to VCR
MAGIC* + 992 + VCR + TV + TV +
MAGIC* + VCR code
MAGIC* + 992 + DVD/LD + TV + TV +
MAGIC* + DVD or LD Player code
MAGIC* + 992 + RCVR + TV + TV +
MAGIC* + Audio code
MAGIC* + 992 + AUX + TV + TV +
MAGIC* + Audio code
MAGIC* + 992 + CD + TV + TV +
MAGIC* + CD Player code
MAGIC* + 992 + CBL/SAT + TV + TV
+ MAGIC* + Cable/DBS code
MAGIC* + 992 + TV + VCR + VCR +
MAGIC* + TV code
MAGIC* + 992 + DVD/LD + VCR + VCR
+ MAGIC* + DVD or LD Player code
MAGIC* + 992 + RCVR + VCR + VCR
+ MAGIC* + Audio code
MAGIC* + 992 + AUX + VCR + VCR +
MAGIC* + Audio code
MAGIC* + 992 + CD + VCR + VCR +
MAGIC* + CD Player code
Test the unit by pressing POWER. If the batteries
are inserted correctly, the red light will blink.
DVD/LD Brand:
Remember, if you want to use your Cinema 7 to operate
your CD Player, press the CD key first.
TV to DVD/LD
TV to RCVR
TV to AUX
Locate the brand name of your DVD or Laser Disc Player
in the “Setup Codes For DVD or Laser Disc Players”
section. The brands are listed in alphabetical order with
the most popular codes listed first. You will use one of
these codes to program your Cinema 7 to operate your
DVD or Laser Disc Player.
NOTE: Removing the batteries will not require you to
reprogram your remote control because the Cinema 7 has
unlimited memory backup.
FF
Programming the Cinema 7 to operate your Cable
Converter or Satellite:
Locate the brand name of your Cable Converter or
Satellite and then write it in the space below.
REC
5.
When your TV turns OFF, press and release
MAGIC to lock in the code for your TV. Your
Cinema 7 is now programmed to operate your TV.
SETTING UP YOUR COMPONENTS
STOP
TV to CD
Cable Converter Brand:
To program the Cinema 7 to operate your DVD or Laser
Disc Player:
Programming the Cinema 7 to operate your TV:
Locate the brand name of your TV and then write it in the
space below.
PAUSE
or
TV to CBL/SAT
VCR to TV
Satellite Brand:
1.
Turn on your DVD or Laser Disc Player and
insert a disc.
*If you are searching for your VCR, CD, LD or DVD Player
code, you may want to use the PL (Play) key instead of
the POWER key to search for your code. When your VCR
starts to play, press MAGIC to lock in your code.
NOTE: To search for the codes of your other components,
repeat Steps 1 through 4, only substitute the appropriate
device key (VCR, DVD/LD, RCVR, AUX, CD or CABLE/
SAT) for the component you are searching for.
Locate the brand name of your Cable Converter or
Satellite in the “Setup Codes For Cable Converters or
Satellites” section. The brands are listed in alphabetical
order with the most popular codes listed first. You will use
one of these codes to program your Cinema 7 to operate
your Cable Converter or Satellite.
TV Brand:
TV/VCR
The TV/VCR key operates the same as the TV/
VCR key on your original VCR remote. The TV/
VCR key also controls the following functions in
other modes: TV mode = TV/VIDEO, CBL/SAT
mode = A/B or TV/SAT, DVD/LD mode = TV/LD,
RCVR mode = Input Select, CD mode = A/B.
2.
Press DVD/LD and release. Press and hold
MAGIC until the Cinema 7’s red light blinks
twice, then release MAGIC.
DVD/LD
Locate the brand name of your TV in the “Setup Codes
For TVs” section. The brands are listed in alphabetical
order with the most popular codes listed first. You will use
one of these codes to program your Cinema 7 to operate
your TV.
VCR to DVD/LD
VCR to RCVR
VCR to AUX
VCR to CD
MAGIC
3.
4.
Enter the first four-digit DVD or Laser Disc
Player code listed for your brand in the “Setup
Codes For DVD or Laser Disc Players” section.
If you perform this procedure correctly, the red
light will blink twice when you enter the final
digit of your code.
To program the Cinema 7 to operate your Cable Converter
or Satellite:
To program the Cinema 7 to operate your TV:
The MENU key operates the same as the
MENU or OSD (On Screen Display) key on
your original remote. Use L,LL, , and
(Menu Up, Down, Left and Right) to navigate
your menus. If your original remote control had
a SELECT key to select options in your menus,
use SEL. Use the EXIT key to exit/clear your
On-Screen menus. Please consult your home
entertainment component’s original owner’s
manual for more detailed instructions on
accessing and navigating your On-Screen
menus.
1.
2.
Turn on your TV.
1.
Turn on your Cable Converter or Satellite.
LEARNING THE CODES PROGRAMMED INTO
THE CINEMA 7
FEATURES AND FUNCTIONS
Press TV and release. Press and hold MAGIC
until the Cinema 7’s red light blinks twice, then
release MAGIC.
2.
Press CABLE/SAT and release. Press and
hold MAGIC until the Cinema 7’s red light
blinks twice, then release MAGIC.
VCR to CBL/SAT MAGIC* + 992 + CBL/SAT + VCR +
TV
MENU
The Light (LED) flashes red to show that the
remote is working and is sending a signal.
CABLE/SAT
VCR + MAGIC* + Cable/DBS code
If you have set up the Cinema 7 using the “SEARCHING
FOR YOUR CODE” procedure, you may want to figure out
which three-digit code is operating your equipment. Use
this procedure after you have set up your components to
find out which four-digit code is operating your equipment.
For example, to find out which code is operating your TV
after setting up your TV using the “SEARCHING FOR
YOUR CODE” procedure:
Aim the Cinema 7 at your DVD or Laser Disc
POWER Player and press POWER. Your DVD or Laser
Disc Player should turn off. If your DVD or
Laser Disc Player does not respond, repeat
steps 2-4, trying each code listed for your
brand until you find the one that operates your
DVD or Laser Disc Player.
DVD/LD to TV
MAGIC* + 992 + TV + DVD/LD + DVD/
LD + MAGIC* + TV code
MAGIC
MAGIC
The MAGIC key is used to program your
Cinema 7.
MAGIC
3.
4.
Enter the first four-digit TV code listed for your
brand in the “Setup Codes For TVs” section. If
you perform this procedure correctly, the red
light will blink twice when you enter the final
digit of your code.
3.
4.
Enter the first four-digit Cable Converter or
Satellite code listed for your brand in the “Setup
Codes For Cable Converters or Satellites”
section. If you perform this procedure correctly,
the red light will blink twice when you enter the
final digit of your code.
DVD/LD to VCR
MAGIC* + 992 + VCR + DVD/LD +
DVD/LD + MAGIC* + VCR code
The POWER key controls power ON and OFF
POWER the same as the POWER key on your original
remote. Please note that most CD Players do
not have an ON/OFF function on the original
remote control. If this is the case with your CD
Player, then POWER will have no effect on
your CD Player.
DVD/LD to RCVR MAGIC* + 992 + RCVR + DVD/LD +
DVD/LD + MAGIC* + Audio code
DVD/LD to AUX
DVD/LD to CD
MAGIC* + 992 + AUX + DVD/LD +
DVD/LD + MAGIC* + AUDIO code
MAGIC* + 992 + CD + DVD/LD +
DVD/LD + MAGIC* + CD Player code
SEL
EXIT
TV
1.
Press TV and release. Press and hold MAGIC
until the Cinema 7’s red light blinks twice, then
release MAGIC.
5.
Your Cinema 7 is now programmed to operate
your DVD or Laser Disc Player.
Write your DVD or Laser Disc Player code in
the boxes to the left for future reference.
Aim the Cinema 7 at your TV and press
POWER. Your TV should turn off. If
your TV does not respond, repeat steps 2-4,
trying each code listed for your
brand until you find the one that operates your
TV.
POWER
POWER
Aim the Cinema 7 at your Cable Converter or
Satellite and press POWER.Your Cable
Converter or Satellite should turn off. If your
Cable Converter or Satellite does not respond,
repeat steps 2-4, trying each code listed for
your brand until you find the one that operates
your Cable Converter or Satellite.
MAGIC
DVD/LD to CBL/SAT MAGIC* + 992 + CBL/SAT + DVD/LD +
The
Right) keys are used to navigate your On-Screen
menus. The
,
, LL, and L (Menu Up, Down, Left and
DVD/LD + MAGIC* + Cable/DBS code
The TV, VCR, DVD/LD, RCVR, AUX, CD and
2.
3.
Press 9 - 9 - 0.
9 - 9 - 0
TV
RCVR to TV
MAGIC* + 992 + TV + RCVR + RCVR
+ MAGIC* + TV code
CABLE/SAT keys are used to select the home
,
, L, and L keys also control
Remember, if you want to use your Cinema 7 to operate
your DVD or Laser Disc Player, press the DVD/LD key first.
VCR
entertainment component you want to control.
For the first digit of your four-digit code, press
1 and count the number of times the red light
(LED) blinks on the Cinema 7. If the light does
not blink when you press the number 1, the
digit is zero.
1
the following functions in other modes: RCVR
and AUX mode = Rear Level +/- and Balance
Left/Right, CD mode = Track+/- and Disc +/-.
RCVR to VCR
MAGIC* + 992 + VCR + RCVR +
RCVR + MAGIC* + VCR code
If your component does not respond when you
DVD/LD
5.
Your Cinema 7 is now programmed to operate
your TV. Write your TV code in
the boxes to the left for future reference.
press a key on the remote control, press the
Programming the Cinema 7 to operate your Receiver/
Tuner:
Locate the brand name of your Receiver/Tuner and then
write it in the space below.
RCVR to DVD/LD MAGIC* + 992 + DVD/LD + RCVR +
RCVR + MAGIC* + DVD or LD Player
code
appropriate device key (TV, VCR,
5.
Your Cinema 7 is now programmed to operate
your Cable Converter or Satellite. Write your
Cable Converter or Satellite code in the boxes
to the left for future reference.
RCVR
DVD/LD, RCVR, AUX, CD or CABLE/SAT)
The SEL (Select) key selects options in your
On-Screen menus. The SEL key also controls
the following functions in other modes: RCVR
and AUX mode = Surround Mode, CD mode =
Disc Select, DVD/LD mode = Chapter.
AUX
first to tell the remote control which component
4.
5.
6.
For the second digit, press 2 and count the
number of times the red light (LED) blinks on
the Cinema 7. If the light does not blink when
you press the number 2, the digit is zero.
RCVR to CD
MAGIC* + 992 + CD + RCVR + RCVR
+ MAGIC* + CD Player code
you would like the remote to operate.
2
3
4
CD
SEL
Receiver/Tuner Brand:
Remember, if you want to use your Cinema 7 to operate
your TV, press the TV key first.
RCVR to CBL/SAT MAGIC* + 992 + CBL/SAT + RCVR +
CABLE/SAT
Locate the brand name of your Receiver/Tuner in the
“Setup Codes For Receivers/Tuners” section. The brands
are listed in alphabetical order with the most popular
codes listed first. You will use one of these codes to
program your Cinema 7 to operate your Receiver/Tuner.
To program the Cinema 7 to operate your Receiver/Tuner:
Remember, if you want to use your Cinema 7 to operate
your Cable Converter or Satellite, press the CABLE/SAT
key first.
RCVR + MAGIC* + Cable/DBS code
The EXIT key exits or clears your on-screen
menus. The EXIT key also controls the
following functions in other modes: RCVR,
AUX and CD mode = Open/Close.
AUX to TV
MAGIC* + 992 + TV + AUX + AUX +
MAGIC* + TV code
Programming the Cinema 7 to operate your VCR:
Locate the brand name of your VCR and then write it in
the space below.
For the third digit, press 3 and count the
number of times the red light (LED) blinks on
the Cinema 7. If the light does not blink when
you press the number 3, the digit is zero.
VOL
The VOLL (Volume Up), VOLL (Volume
EXIT
AUX to VCR
AUX to DVD/LD
AUX to CD
MAGIC* + 992 + VCR + AUX + AUX +
MAGIC* + VCR code
Down) and MUTE keys control the volume the
Programming the AUX Key:
VOL
same as the Volume Up and Down and Mute
keys on your original remote.
The AUX key is already set up to accept codes for a
second Receiver/Tuner, Amplifier or other audio compo-
nent. If you would like to set up the AUX key for an audio
component, follow the instructions listed below. If you
would like the AUX key to control a second TV, VCR,
Cable Converter or other component, follow the instruc-
tions in the “Re-assigning Device Keys” section to re-
assign the AUX key to accept codes for other components.
For example, if you are setting up an Amplifier:
Locate the brand name of your Amplifier and then write it
in the space below.
VCR Brand:
MAGIC* + 992 + DVD/LD + AUX + AUX
+ MAGIC* + DVD or LD Player code
MAGIC* + 992 + CD + AUX + AUX +
MAGIC* + CD Player code
MUTE
1.
Turn on your Receiver/Tuner.
The PROG/GUIDE key operates your
components secondary menus as well as your
DBS system’s and Cable Converter’s Guide
function. Use the
For the fourth and final digit, press 4 and count
the number of times the red light (LED) blinks
on the Cinema 7. If the light does not blink
when you press the number 4, the digit is zero.
Now you have your four-digit code.
Locate the brand name of your VCR in the “Setup Codes
For VCRs” section. The brands are listed in alphabetical
order with the most popular codes listed first. You will use
one of these codes to program your Cinema 7 to operate
your VCR.
PROG/GUIDE
2.
Press RCVR and release. Press and hold
MAGIC until the Cinema 7’s red light blinks
twice, then release MAGIC.
RCVR
MAGIC
The CHLL(Channel Up) and CHL (Channel
CH
Down) keys change channels the same as the
AUX to CBL/SAT MAGIC* + 992 + VCR + AUX + AUX +
Channel Up and Down keys on your original
CH
,
, LL, and L (Menu Up, Down, Left and
MAGIC* + Cable/DBS code
remote. The CHL/L keys also control the
following functions in other modes: DVD/LD
mode = Skip Forward/ Skip Reverse, RCVR,
AUX and CD mode = Preset Up/Preset Down.
Right) keys to navigate your menus. If your
original remote control had a SELECT key to
select options in your menus, use SEL. Use
the EXIT key to exit/clear your On-Screen
menus. Please consult your home entertain-
ment component’s original owner’s manual for
more detailed instructions on accessing and
navigating your On-Screen menus.
CD to TV
MAGIC* + 992 + TV + CD + CD +
MAGIC* + TV code
3.
4.
Enter the first four-digit Receiver/Tuner code
listed for your brand in the “Setup Codes For
Receivers/Tuners” section. If you perform this
procedure correctly, the red light will blink twice
when you enter the final digit of your code.
To program the Cinema 7 to operate your VCR:
NOTE: To find out the code for your other components,
repeat Steps 1 through 6, only substitute the
appropriate device key (VCR, DVD/LD, RCVR,
AUX, CD or CABLE/SAT) for the component
code you wish to learn.
1.
Turn on your VCR and insert a tape.
CD to VCR
MAGIC* + 992 + VCR + CD + CD +
MAGIC* + VCR code
2.
Press VCR and release. Press and hold
MAGIC until the Cinema 7’s red light
blinks twice, then release MAGIC.
VCR
CD to DVD/LD
CD to RCVR
CD to AUX
MAGIC* + 992 + DVD/LD + CD + CD
+ MAGIC* + DVD or LD Player code
MAGIC* + 992 + RCVR + CD + CD +
MAGIC* + Audio code
The Digit keys (0-9) control direct channel
0 - 9
Amplifier Brand:
SEL
EXIT
access the same as the Digit keys on your
original remote. The Digit keys (0-9) also
control the following functions in other modes:
RCVR and AUX modes = Input Selections.
MAGIC
POWER
Aim the Cinema 7 at your Receiver/Tuner and
press POWER. Your Receiver/Tuner should
turn off. If your Receiver/Tuner does not
respond, repeat steps 2-4, trying each code
listed for your brand until you find the one that
operates your Receiver/Tuner.
Locate the brand name of your Amplifier in the “Setup
Codes For Amplifiers” section. The brands are listed in
alphabetical order with the most popular codes listed first.
You will use one of these codes to program your Cinema 7
to operate your Amplifier.
SETTING UP OTHER COMPONENTS
3.
4.
Enter the first four-digit VCR code listed for
your brand in the “Setup Codes For VCRs”
section. If you perform this procedure correctly,
the red light will blink twice when you enter the
final digit of your code.
MAGIC* + 992 + AUX + CD + CD +
MAGIC* + Audio code
MAGIC* + 992 + CBL/SAT + CD + CD
The DISPLAY key operates the Display
function of your home entertainment
components.
In addition to the components labeled on the device keys
(TV, VCR, DVD/LD, CBL/SAT, etc.), the Cinema 7 can also
operate the following components: Cassette Decks,
Infrared Home Automation, Video Accessories and
Miscellaneous Audio Components (Graphic Equalizers
and Digital Music Service Boxes).
CD to CBL/SAT
CBL/SAT to TV
The ENTER key operates the same as the
DISPLAY
+ MAGIC* + Cable/DBS
code
Enter key on your original remote. If your
original remote control required you to use an
To program the Cinema 7 to operate your Amplifier:
ENTER
MAGIC* + 992 + TV + CBL/SAT +
The PIP On/Off key accesses your TV’s
Picture-in-Picture feature. The PIP On/Off key
also controls the following functions in other
modes: CD mode =Disk Skip, DVD/LD mode =
Subtitle On/Off, CBL/SAT mode = View.
5.
Your Cinema 7 is now programmed to operate
your Receiver/Tuner. Write your Receiver/
Tuner code in the boxes to the left for future
reference.
1.
Turn on your Amplifier.
CBL/SAT + MAGIC* + TV code
POWER Aim the Cinema 7 at your VCR and press
POWER. Your VCR should turn off. If your original
VCR remote control did not have a POWER key,
press PL (Play). Your VCR should start to play. If
your VCR does not respond, repeat steps 2-4,
trying each code listed for your brand until you
find the one that operates your VCR.
Enter key to change channels, use the ENTER
key on the Cinema 7 after entering your
channel number. The ENTER key also controls
the following functions in other modes: RCVR
and AUX modes = TAPE MON.
P
I
P
CBL/SAT to VCR MAGIC* + 992 + VCR + CBL/SAT +
CBL/SAT + MAGIC* + VCR code
CBL/SAT to DVD/LD MAGIC* + 992 + DVD/LD + CBL/SAT
+ CBL/SAT + MAGIC* + DVD or LD
AUX
2.
Press AUX and release. Press and hold
MAGIC until the Cinema 7’s red light
blinks twice, then release MAGIC.
or
The Setup Codes for these components can be accessed
under the following device keys:
MAGIC
PL
Cassette Decks:
Use the VCR Key
Remember, if you want to use your Cinema 7 to operate
your Receiver/Tuner, press the RCVR key first.
The SWAP key swaps the Picture-in-Picture
window and the TV’s main picture. The SWAP
key also controls the following functions in
other modes: CBL/SAT mode = SAT.
Swap
Move
3.
4.
Enter the first four-digit Amplifier code listed for
your brand in the “Setup Codes For Amplifiers”
section. If you perform this procedure correctly,
the red light will blink twice when you enter the
final digit of your code.
code
IR Home Automation:
Video Accessories:
Miscellaneous Audio:
Use the CD Key
CBL/SAT to RCVR MAGIC* + 992 + RCVR + CBL/SAT +
CBL/SAT + MAGIC* + Audio code
Use the CBL/SAT Key
Use the AUX or RCVR Key
Programming the Cinema 7 to operate your CD Player:
Locate the brand name of your CD Player and then write
it in the space below.
5.
Your Cinema 7 is now programmed to operate
your VCR. Write your VCR code in the boxes to
the left for future reference.
CBL/SAT to AUX MAGIC* + 992 + AUX + CBL/SAT +
CBL/SAT + MAGIC* + Audio code
For example, to set up a Cassette Player on the VCR key:
1.
Turn on your Cassette Player and insert a tape.
The MOVE PIP key moves the Picture-in-
Picture window around your TV screen. The
MOVE PIP key also controls the following
CBL/SAT to CD
MAGIC* + 992 + CD + CBL/SAT +
CBL/SAT + MAGIC* + CD Player code
POWER
Aim the Cinema 7 at your Amplifier and press
POWER. Your Amplifier should turn off. If your
VCR
CD Player Brand:
2.
Press VCR and release. Press and hold
MAGIC until the Cinema 7’s red light blinks
twice, then release MAGIC.
MAGIC
*NOTE: Here (*) you must hold MAGIC until the Cinema
7’s red light blinks twice.
This product has been discontinued and is no longer
1.
2.
Press and release the CBL/SAT key then press
the SLEEP key once to set the Cinema 7’s built-
in sleep timer for 15 minutes. The red light will
blink once.
supported
Janeil
JBL
0046
Scimitsu
Scotch
Scott
0019
0045
0020
0042
Quartz
Quasar
0046
0162, 0035,
0077, 0454
MGA
Mitsubishi 0048*
Orion 0002, 0294,
0479
0240
Denon
DKK
Emerson
Fisher
0003
DBS
0790
0082
CABLE/SAT
SLEEP
Oak
0007, 0019
0021
0054
0178
Daytron
Denon
0000
Toshiba
PROGRAMMING THE MACRO KEYS
Optimus
JCB
0000
0236, 0019,
0178, 0179,
0180
0047, 0054,
0056, 0154,
0156, 0171,
0178, 0159,
0179
0180
0156
0093, 0165,
0039, 0386
0019
0305
0048, 0174,
0179
0393, 0420
0032, 0305
Uniden DBS 0724
Uniden
Panasonic 0021, 0107,
0000
Panther
Paragon
Philips
The Cinema 7 has two Macro keys (MACRO and MACRO2)
that allow the user to play back a series of keystrokes, at
any time, with the press of one key. For example, to set up a
sequence that will turn on your components and change the
components to the proper inputs:
JVC
Kaypani
KEC
Kenwood
Kloss
KTV
0053
Dynatech 0000
Electrohome0037
Electrophonic 0037
RadioShack 0000, 0037
0052, 0074,
0076, 0238
SLEEP
Each additional press of the SLEEP key will add
15 more minutes to the Sleep Timer, up to a
maximum of 60 minutes. The LED will blink
twice when the sleep timer is set for 30 minutes,
3 times for 40 minutes, or 4 times for 60
minutes.
0052
Radix
Randex
RCA
0037
0037
Panasonic 0035*, 0162*
0637
0000
0153, 0025,
0027, 0031
0753, 0144,
0023
0180
Sears
Penney’s
0035*, 0240,
0162*
Garrard
Genexxa
Harman/Kardon0173
Hitachi
JVC
Kenwood
Setup Codes For
Amplifiers
0019, 0030
0024, 0046
0030, 0180,
0185, 0280,
0032
Emerex
Emerson
0032
0060, 0202,
0240, 0042,
0035, 0048,
0077, 0105,
0106, 0149
0000, 0035,
0037, 0046,
0047, 0048,
0062, 0066,
0104
0209, 0184,
0479, 0278,
0000, 0002,
0036, 0037,
0043, 0061,
0068, 0121,
0184, 0208,
0212, 0295,
0361
Quasar
RCA
0035*, 0162*
0035*, 0060*,
0048*
Carver
Denon
GE
0269
0160
0078
0331
0356
0269
0165
1.
Press and hold MAGIC until the Cinema 7’s
red light blinks twice, then release
MAGIC.
MAGIC
0032
0072
0028, 0037,
0048, 0190
0157
0157
0305
Pioneer
Popular
Mechanics 0400
Prelude
Pulsar
RadioShack 0015, 0315,
0797
RCA
Semivox
Semp
Sharp
Sansui
Sanyo
Sears
Sony
0000, 0479
0240
0000, 0037
0032*
JVC
NOTE: The sleep timer starts 10 seconds after the last
press of the SLEEP key. Once you have activated the
Cinema 7’s built-in sleep timer, you must keep the remote
control aimed directly at the component.
LG
0056
Realistic
Kenwood
Linn
2.
3.
Press 9 - 9 - 5. The Cinema 7’s red light will
blink twice.
9 -9 -5
Logik
Luxman
LXI
0016
Krell
Linn
LXI
0770
0000
0056
Luxman
0047, 0054,
0154, 0156,
0178
Shogun
Signature 0016
Simpson
Sony
Soundesign 0178, 0179,
0180, 0186
Spectricon 0003
Squareview 0171
SSS
Starlite
Symphonic 0000
Zenith 0000
Setup Codes for DVD
Players
Magnavox 0269
Press and release one of the MACRO keys.
This will be the key that will play back the
series of keystrokes assigned to that key.
MACRO
POWER
3.
To de-activate the built-in sleep timer, press
POWER.
Magnavox 0157, 0305
Marantz
Marantz
0269, 0321
or
0186, 0187
0000, 0080
Fisher
0104, 0047,
0054, 0066
0033, 0035
0000
Ricoh
Runco
Samsung 0240, 0045
Sanky
Sansui
0034, 0253
0039
0029, 0157,
0180
Nakamichi 0321
MACRO 2
0021
Magnavox 0054, 0096,
0186, 0187,
NEC
Optimus
0264
0013, 0300,
0395
0269
0013, 0300
0395
0321
0264
0220, 0689
NOTE: Plugging your TV into the outlet on the back of the
Cable Converter may allow you to turn both your Cable
Converter and your TV ON and OFF.
Realistic
Recoton
Regal
0207
Fuji
JVC
Kenwood
0558
0534
MCS
Mission
MTC
Nikko
NSM
Onkyo
Optimus
0029
4.
5.
Begin entering the sequence of keystrokes, up
to 15, that you wish to be played back when
you press the MACRO key. For example:
0400
0020, 0024,
Funai
Garrard
GE
0048, 0039
0000, 0041,
0067, 0271,
0479
0104, 0046,
0047, 0054,
0240
0043, 0045,
0121, 0184,
0210, 0212
0000, 0035,
0037, 0042,
0046, 0047,
0054, 0066,
0104, 0105
0045
0157
0259, 0020
0002
0030, 0386
0000
Mitsubishi 0521
Panasonic 0490
0420
Philips
Pioneer
Realistic
Sansui
Shure
Regency
Majestic
Marantz
Matsushita 0250
Megatron 0145, 0003,
0178
MEI
Memorex
0016
0060, 0202,
0035, 0048,
0240
0174
Rembrandt 0011
RCVR + POWER + TV + POWER + TV/VCR
(To change the input on the TV to VIDEO 1) +
CBL/SAT + POWER.
0054, 0030
0019, 0180
0180
Philips
Pioneer
RCA
0539
0525
0522
0533
0503
0503
0157
TROUBLE SHOOTING
Runco
0000
Sanyo
Scott
0101
Samsung 0144, 0040
Scientific
Problem
Solution
Supre-Macy 0046
Supreme
Sylvania
Goldstar
0037, 0038
0000, 0032,
0037, 0048,
0145, 0179,
0305, 0420,
0437, 0468
0000
0054, 0096,
0020, 0030
Go-Video 0432, 0526
Gradiente 0000, 0008
Harley
Sony
Sony
Atlanta
0477, 0008,
0017
0510
0015, 0040
Red light does not
Replace the batteries with four
Once your sequence is entered, press and
hold MAGIC until the Cinema 7’s red light
blinks twice.
0185
Toshiba
Zenith
Soundesign 0078, 0211
MAGIC
blink when you press (4) new AAA alkaline batteries.
a key?
0056, 0150,
0154, 0016,
0178
Technics
Victor
Wards
0308
0331
0013, 0078,
0211
0133, 0143,
0354, 0504
Seam
Signal
Signature 0011
SL Marx
Sprucer
Starcom
Stargate
Symphonic 0171
Tandy
Tatung
Technics
Davidson 0000
Setup Codes for Laser
Disc Players
Mitsubishi 0059
0093
0055, 0003
0250, 0051
Harman/Kardon
0038
0072, 0068,
0072
Sears
Panasonic 0029
Philips
Pioneer
Now, using the example above, whenever the programmed
MACRO key is pressed, the Receiver would power ON, the
TV will power ON and change the input to VIDEO 1 and
then the Satellite would power ON.
Repeat steps 1 - 5 to then setup a second sequence on
the MACRO2 key.
The Cinema 7 does
not operate your
Try all of the codes listed for your
brand of home entertainment
component in the “Setup Codes”
MGA
0150, 0019,
0030, 0178
0017, 0047,
0051, 0135,
0032, 0039
0021
Harwood
0157
0040
0021
0003, 0015
0770, 0015,
0040
home entertainment
NAD
Pioneer
Sony
0059
0032, 0468,
0244, 0305
0157
Yamaha
components or is not section. Many setup codes may
performing com-
mands properly?
Midland
Technol Ace 0179
Techwood 0051, 0056,
0003
Headquarter 0046
0059
allow for partial functionality,
however, only one setup code
will operate your home entertain-
ment component correctly. Make
sure that all of the compo-
nents you are setting up can
be operated with an infrared
remote control.
HI-Q
Hitachi
0047
0193, 0201
Proton
QED
Quasar
RCA
Setup Codes For Audio
Cassette Decks
Aiwa
Carver
Denon
Harman/Kardon 0182
JVC
Kenwood
Magnavox 0029
Marantz
Onkyo
Optimus
Philips
Pioneer
0041, 0105,
0000, 0042
0041
Semp
Setup Codes For
Receivers/Tuners
0157
0029
Minutz
Mitsubishi 0150, 0093,
0019, 0178
Motorola
MTC
Teknika
0054, 0056,
0060, 0092,
0150, 0016,
0019, 0179,
0180, 0186,
0039
Sharp
Shintom
Shogun
Singer
Sony
0048, 0062
0072
0240
0072
0029, 0197
0029
0076
Starquest 0015
Sylvania
Tandy
Teleview
Texscan
TFC
Timeless
Tocom
Toshiba
Tusa
TV86
Unika
VOLUME LOCK
Jensen
JVC
ADC
Aiwa
0531
0121, 0158,
0189
0764, 0053,
0179, 0305
0179, 0180,
0420
0157, 0420
0157
0157, 0305
0179
0305
0305
0037, 0180
0001
0008, 0041,
0067
0258
Volume Lock allows the user to designate which compo-
nent will control the volume in the TV, DVD/LD and CBL/
SAT modes. To set the Volume Lock to the TV mode:
0093, 0055
0060, 0019,
0030, 0056,
0185
0180
0156, 0166,
0178
Realistic
0040
KEC
Kenwood
0037, 0278
0038, 0041,
0067
0032, 0033,
0034, 0000,
0035, 0253
0042
Capetronic 0531
Carver
0244, 0273
0070
0001
0008, 0042,
Rotel
SAE
Sansui
Sanyo
Scott
Sears
Sharp
0310
1.
Press and hold MAGIC until the Cinema 7’s
red light blinks twice, then release
MAGIC.
MAGIC
Telefunken 0056
TMK
0189, 0360
0195
The Cinema 7 is
not performing
Try all of the codes listed for your
brand of home entertainment
0418
Multitech
NAD
0056, 0177,
0178
0156, 0060,
0154
0185
KLH
0072
STS
Sunpak
Sylvania
Casio
0029
0012, 0013
0000
commands properly? component in the “Set-Up
Codes” section. Many set-up
codes may allow some degree of
operation. However, only one
set-up code will work correctly
with your home entertainment
component.
Kodak
Lloyd’s
Logik
LXI
0035, 0037
0000, 0208
0072
0253
Clarinette 0195
0135, 0282
0027, 0220
0029
Toshiba
Tosonic
Totevision 0039
Universal
Vector
0035, 0081,
0043, 0000,
0110
Denon
Emerson
Fisher
0004
0424
0042, 0219,
0360
0424, 0463
0015
0063
0153, 0022,
0207
2.
Press 9 - 9 - 3. The Cinema 7’s red light will
blink twice.
9 -9 -3
NEC
0019, 0030,
0056
One For All® is the registered trademark of Universal
Electronics Inc. Computime International LTD. is the Licensee
of the ONE FOR ALL® brand for the United States of America
and Canada.
0037
0027, 0099,
0220
0029
Nikko
0030, 0092,
0178
Magnasonic 0278
Magnavox 0035, 0081,
0000, 0039,
Symphonic 0000
Tatung
TEAC
Technics
Teknika
Sherwood 0180
3.
Press and release TV. The Cinema 7’s red light
will blink twice.
TV
0027
0041
Garrard
Sony
0000, 0185
Sansui
Sony
United
Artists
United
Cable
Universal
Noshi
NTC
Onwa
Optimus
0018
0000, 0041
0162, 0035
0000, 0035,
0037
Harman/Kardon0110
Soundesign 0145
0170, 0243,
0291
0007
0092
Research 0030
Victor
0110, 0149
0240
0035, 0081
0037
JVC
Kenwood
0074
Tascam
TEAC
0420
Now, whenever you press VOLL, VOLL or MUTE in the
VCR, DVD/LD and CBL/SAT modes your TV will control
the volume. If you would like to change the Volume Lock
setting to the VCR, DVD/LD or CBL/SAT modes repeat
steps 1-3, only substitute the appropriate device key.
Setting the Volume Lock to the TV, VCR, DVD/LD or CBL/
SAT mode will not effect the volume control in the RCVR,
AUX and CD mode.
You can also change the Volume Lock setting so that an
Audio component controls the volume in all device modes.
To change the Volume Lock setting on the Cinema 7 to the
RCVR or AUX mode:
Problems program-
ming a TV/VCR
combo?
Try the VCR set-up codes for
your brand. However, some
combo units may require both a
TV code for volume control and
a VCR code for the remaining
functions.
0180
0053
0054
0019, 0178
0046
0016, 0019,
0030, 0054,
0056, 0080,
0096, 0165,
0178, 0179,
0020, 0021,
0027
Magnin
Marantz
Marta
0027, 0313,
0314, 0077,
0186
0174, 0180,
0393, 0420
0029
Technics
Victor
Wards
Yamaha
0229
0003
Copyright 2000 by Universal Electronics Inc. No part of this
publication may be reproduced, transmitted, transcribed, stored
in any retrieval system, or translated to any language, in any
form or by any means, electronic, mechanical, magnetic, optical,
manual, or otherwise, without the prior written permission of Uni-
versal Electronics Inc.
0250, 0154,
0166
Vidikron
Vidtech
Viking
0273
0153, 0022,
0056, 0191,
0207
Thomas
TMK
0000
0240, 0036,
0208
0043, 0045,
0066, 0210,
0212
Technics
Victor
Wards
Yamaha
Yorx
Setup Codes for Cable
Converters
ABC
0027
Optonica
Orion
Panasonic 0250, 0051,
0055
Penney
0093, 0165
0236, 0436
Matsushita 0162, 0035,
0454
Koss
Linn
Lloyd’s
LXI
0424
0072
0157
0036, 0187
0461
0094, 0097
Wards
0189
Setup Codes For IR
Home Automation
Videoway 0250
Viewstar
MEI
Memorex
0035
Toshiba
0195
0063, 0027,
0258
0525, 0000
0400
VCR not recording?
As a safety feature on the
Cinema 7, you must press the
REC key twice.
0162, 0240,
0035, 0037,
0104, 0000,
0039, 0046,
0047, 0048
0043, 0061,
0240
0181
GE
0240
0047, 0156,
0051, 0030,
0019, 0003,
0018, 0021,
0027, 0060,
0135, 0178,
0032, 0039
0054, 0145,
0096, 0019,
0020, 0030
0054
0019, 0030,
0039
0166, 0038
0092, 0019,
0039
0051
0047
0003, 0052,
0178
0017, 0019
0250, 0051,
0055, 0165
Magnavox 0189, 0195,
0531
LiteTouch 0084
Zenith
Zentek
Setup Codes for
Satellites
AlphaStar
DBS
Chaparral 0053, 0216
Echostar
One For All is designed for compatibility in North America
excluding Mexico.
Totevision 0037, 0240
Unitech 0240
Vector Research
0038, 0040
Vector 0045
Video Concepts0040,
0045, 0061
Lutron
0318, 0597
Marantz
MCS
0039, 0189
0039
0003, 0008,
0014, 0007,
0001, 0011,
0013, 0017
0153, 0315
0022, 0207
0797, 0153,
0022, 0207
0056
One For All 0167
RadioShack 0240
Security System
0167
CH L/L and PREV
CH not working for
your RCA TV?
Due to RCA design (1983-1987),
only the original remote control
will operate these functions.
1.
Press and hold MAGIC until the Cinema 7’s
red light blinks twice, then release
MAGIC.
MAGIC
White
MGA
MGN
Modulaire 0195
NAD 0320
Nakamichi 0347
URC-7200 Cinerma 7
01/01
Westinghouse0451, 0463,
0236, 0180
0772
Problems changing
channels?
If your original remote control
required an Enter keystroke
when changing channels, press
the ENTER key on the Cinema 7
after you enter the channel
number.
Setup Codes For TVs
Allegro
Antronix
Archer
Universal X10 0167
X10
Setup Codes For Video
Accessories
Archer
GC Electronics 0160
Jebsee
Rabbit
RadioShack 0160
Roctec 0456
SuperGuide 0169
TeleCaption 0171
Setup Codes For
Miscellaneous Audio
Aiwa
Fisher
Harman/Kardon0477
Jerrold
JVC
Nikko
Paramount
Pictures
RCA
Schneider 0376
Scientific
Atlanta
Sony
Soundesign 0376
SSI
Abex
0032
Curtis
Philco
Yamaha
Zenith
0019, 0030
0017, 0092,
0016
Technology 0240
Onkyo
0135
0167
9 -9 -3
2.
Press 9 - 9 - 3. The Cinema 7’s red light will
blink twice.
Admiral
0093, 0179,
0180, 0016,
0047
Mathes
0030, 0060,
0154, 0039
0180
0451, 0092,
0019, 0039
0019
Minolta
0042, 0105
Videosonic 0240
Wards
Optimus
0042, 0080,
0177, 0181,
0186, 0219,
0531, 0670
DBS
Echostar
0775
0159, 0269,
0280
Mitsubishi 0043, 0048,
0061, 0067
0000, 0035,
0042, 0047,
0048, 0060,
0062, 0072,
0081, 0149,
0212, 0240
RCVR
or
CXC
Daewoo
Philips
Pilot
Zonda
0003
Belcor
0160
3.
Press and release RCVR or AUX. The Cinema
7’s red light will blink twice.
Adventura 0046
Aiko
Akai
Alaron
A-Mark
Ambassador0177
Anam
National 0055
Setup Codes For VCRs
Motorola
MTC
Multitech
NEC
0035, 0048
0240, 0000
0000, 0072
0038, 0040,
0041, 0067,
0104
Cable Star 0056
Cabletenna 0022
Cableview 0022
Express
Vu DBS
General
Instrument 0361
Hitachi DBS 0819
Homecable 0238
HTS DBS 0775
Hughes
AUX
0092
0030
0179
0003
The red light blinks
when you press a
key but you receive
no response from
Make sure you are aiming your
Cinema 7 at your home enter-
tainment component and that
you are within 15 feet before
Admiral
0048, 0121,
0184, 0039,
0060, 0202
Panasonic 0039
0160
0081
0775
Now, whenever you press VOLL, VOLL or MUTE your
Audio component will control the volume in all device
modes.
Daytron
Denon
Dumont
Electroband 0000, 0185
Emerson
Pioneer
Portland
Penney
Philips
Pioneer
0195
0189
0014, 0080,
0150, 0531,
0630
0039
0054, 0360,
0531
0163, 0181,
0195
0189
0219
0163, 0322
0186
0145
0017, 0019
Century
Citizen
Colour Voice0025, 0031
Comtronics 0040
0153
0153, 0315
Adventura 0000
White
your home entertain- using your remote.
ment component?
You can also change the Volume Lock setting so that each
component controls its own volume. However, some
components do not have volume control. Using this setting
may eliminate volume control in some device modes. To
change the Volume Lock setting on the Cinema 7 so each
mode controls its own volume:
Prism
Proscan
Proton
Aiko
Aiwa
Akai
0278
Westinghouse0278,
0479, 0209,
0184
0463, 0236,
0180, 0019,
0154, 0177,
0178, 0179,
0185, 0280,
0282, 0038,
0039
0030
0154, 0159
0179
0037, 0000
0041, 0061,
0106
Nikko
Nikon
Noblex
Olympus
Optimus
0037
0034, 0253
0240
Quasar
RCA
Contec
Digi
Eastern
Emerson
0019
0637
0002
0797
Anam
AOC
0180
XR-1000
0000, 0035,
0072
0038
0039, 0000,
0033, 0034
Network
Systems
DBS
IQ Prism
IQ
Janeil
Jerrold
0030, 0019,
0185, 0003,
0052
Pulsar
Quasar
American
High
Asha
Audiovox
Beaumark 0240
Bell &
Howell
Broksonic 0184, 0209,
0479, 0002,
0035
0010, 0159
0052
0035
0240
0037
0162, 0048,
0037, 0104,
0454
Yamaha
Zenith
Realistic
0749
0210
0210
0152
1.
Press and hold MAGIC until the Cinema 7’s
red light blinks twice, then release
MAGIC.
MAGIC
Everquest 0015, 0040
Archer
Audiovox
0003
RadioShack 0047, 0056,
0154, 0019,
Sansui
Sanyo
Scott
Focus
Garrard
GC
0400
0153
0459, 0520
0073
0376
0451, 0092,
0180, 0003
0180
Envision
Fisher
Fujitsu
Funai
Optonica
Orion
0062
Setup Codes For TV/
VCR Combos
American
0030, 0165,
0209, 0184,
0479, 0002,
0295
2.
3.
Press 9 - 9 - 3. The Cinema 7’s red light will
blink twice.
9 -9 -3
Baysonic
Belcor
Bell &
Howell
Bradford
Brockwood 0019
Broksonic 0003
Candle
0178, 0180,
0104
Sharp
Electronics 0056, 0207
Gemini
General
Primestar 0627
0019
0171, 0179,
0180
0032, 0039
High
0035*
Sherwood 0491, 0502
0015
0317
0056
Jerrold
Legend
Magnavox
DBS
Memorex
DBS
Memorex
0361
0269
RCA
0047, 0018,
0019, 0038,
0090, 0135
0056, 0154,
0019, 0030,
0165, 0178,
0180, 0032,
0039
Panasonic 0162, 0035,
0077, 0225,
Brocksonic 0002, 0294,
0479
Sony
0158, 0474
Press and release VOLL. The Cinema 7’s red
light will blink twice.
VOL
0154, 0016
0180
Futuretech 0180
GE
0121, 0295,
Soundesign 0670
Instrument 0476, 0003,
0014, 0011
0047, 0051,
0361
0454
Colt
0072
TEAC
Technics
0163, 0463
0722, 0724
Now, whenever you press VOLL, VOLL or MUTE on the
Cinema 7 each component will control its own volume,
provided each component has volume control.
0451, 0021,
0027, 0055,
0178, 0282,
0135
Realistic
Calix
0037
Penney
0035, 0037,
0038, 0040,
0042, 0054,
0240
Curtis Mathes 0035*
0039, 0309,
0518
Goldstar
0144, 0040
0460
0010, 0159
Canon
Capehart
Carver
CCE
0035
Daewoo
Emerson
0278*
Goodmind 0797
0724
0269
0056, 0030,
0186, 0046
0020
0002, 0294,
0479
Victor
Wards
0074
Hamlin
0259, 0009,
0081
0014, 0042,
0054, 0080,
0158, 0189
0176, 0186
0195
0020, 0034
0011
0317
0459
0376
Panasonic 0152
Panasonic
DBS
USING THE SLEEP KEY
Carnivale 0030
Gibralter
Goldstar
0019, 0030,
0017
0019, 0030,
0178, 0032,
0039
0072, 0278
0278
Pentax
Philco
0042, 0105
0035, 0209,
0479
0035, 0081,
0062, 0110
0037
0067, 0162
0020
0060, 0202
0072
Funai
GE
0000
Hitachi
Hytex
Jasco
Jerrold
Starcom
Yorx
Carver
Celebrity
Cineral
Citizen
0054
0000
Rhapsody 0185
Runco
Sampo
Cineral
Citizen
Colt
0035*, 0060*,
0048*, 0240
0035*, 0000
0000
0007
0701
The SLEEP key allows you to access the sleep timer of
your TV, Cable Converter/DBS Satellite or Audio compo-
nent. You can access your TV, Cable Converter, DBS
Satellite or Audio component’s Sleep Timer by pressing
the SLEEP key. Most Sleep Timers advance in increments
of 10 or 15 minutes, however, for specific instructions on
setting your components Sleep Timer, please consult your
original owners manual.
Even if your original Cable Converter remote control did
not have a sleep timer, your Cinema 7 has its own built-in
sleep timer. If your Cable Converter does not have a sleep
timer, press the SLEEP key to activate the Cinema 7’s
built-in sleep timer. For example:
0017, 0030
0030, 0052,
0032, 0039
0037, 0278
0072
0072, 0240,
0037, 0047,
0271
Yamaha
Yorx
0153, 0315
0476, 0003,
0014, 0011,
0012, 0015
0440
Philips DBS 0722, 0724
Primestar 0361, 0627
RCA DSS 0566
0451, 0092
0060, 0092,
0030, 0056,
0186, 0280,
0039, 0046
0185
Philips
Hitachi
HQ
Lloyds
Magnavox 0000, 0035*,
0081*
Magnin
Memorex
Craig
Setup Codes For CD
Players
Gradiente 0053, 0056
Samsung 0060, 0019,
0030, 0056,
Pilot
0000
Realistic
0052
Grunpy
Hallmark
Harvard
Hitachi
0179, 0180
0178
0180
Pioneer
Portland
Proscan
Protec
Pulsar
Aiwa
0124, 0157
Linsay
Sony DBS 0639
Star Choice
0178, 0032,
Curtis
Mathes
Burmester 0420
California
Magnavox 0027
Clairtone
Concerto
Contec
Craig
0039
0035, 0041,
0060, 0202
0240
0037, 0162*
Memorex
0000
DBS
0869
0180
0210
0056
0145, 0151,
0038, 0056,
0032
Samsux
Sansei
Sanyo
0039
Audio Lab 0029
Movie Time 0063, 0156
Star Trak
STS
0180, 0185
0180
0451
Cybernex 0240
Daewoo 0278, 0020,
0039
0046
Carver
0157, 0179,
0437
Novaplex
NSC
0618
0063, 0156
0154, 0159
Quarter
Toshiba
Crown
0180, 0039
Infinity
0054
|