INSTRUCTION MANUAL
LARGE FACE
SPHYGMOMANOMETER
Models 11-675D and 11-675DNL
11-685 and 11-685NL
160
140
180
300
120
100
80
60
220
240
240
260
280
160
140
180
120
100
80
60
220
240
240
260
280
SPHYGMOMANOMETER
RT
C
E
I
F
I
E
D
40
20
mmHg
M
A
D
E
I
N
J
A
PA
N
SPHYGMOMANOMETER
CERTIFIED
40
20
300
mmHg
M
A
D
E
I
N
J
A
PA
N
COMPONENTS
ASSEMBLY INSTRUCTIONS
Models:
Cuff/Bladder
11-675D
11-675DNL
11-685
Square Face, Wall Mount
Square Face, Wall Mount, LATEX-FREE
Square Face, Floor Stand
Figure1
Sphygmomanometer
160
140
180
120
100
80
60
220
240
240
260
280
11-685NL
Square Face, Floor Stand, LATEX-FREE
SPHYGMOMNOMETER
CERTIIED
40
20
300
mmHg
M
A
D
E
I
N
J
A
PA
N
Omron Clock Aneroid (all models):
(1)
(1)
(1)
(1)
Omron Clock Aneroid (see Models for type)
Adult, Nylon Cuff, blue (model #21-071)
8’ Coiled Tube
Adult, Two-Tube Bladder (model #21-081 Latex, #21-081NL Latex-Free)
Inflation Bulb with Deluxe Air Release Valve (model #21-141 Latex,
#21-125NL Latex-Free, #21-131 Valve)
Coiled Tube, 2.4meter (8ft.) length (model #21-321 Latex,
#21-321NL Latex-Free)
Deluxe Air
Release Valve
(1)
Inflation Bulb
Black Knob
(1)
(1)
Set of metal luer connectors (model #21-331S)
Calibration tool
Chrome-plated poles
Wall-Mount Kit (for models 11-675D and 11-675DNL):
(1)
(1)
(4)
(4)
Wall-Mount Bracket
Wall-Mount Plate
Metal Wall Anchors
Metal Screws
Floor Stand Kit (for models 11-685 and 11-685NL)
(1)
(5)
(2)
(1)
(1)
(1)
(1)
(1)
Five-legged base
Wheel assemblies
Chrome-plated poles
Black Knob
Large Washer
Large Hex Bolt
Small Washer
Five-Legged Base
Large Washer
Wheel Assembly
Round-head bolt (spare)
Small Washer
Large Hex Bolt
3
2
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Omron Clock Aneroid (all models):
Cuff
1. Attach one end of the coiled tube (the end without the metal connector)
to the connector on the underside of the Omron Aneroid (Figure 2).
2. Attach the other end of the coiled tube (the end with
the metal connector) to the tube from the cuff and bladder
(the tube without the bulb assembly).
Figure 5
160
140
180
3. The cuff and bladder assembly can be stored in the
basket on the back of the aneroid. Once mounted
to the wall or affixed to a floor stand, the Omron
Aneroid is ready for use.
120
100
80
60
220
240
240
260
280
SPHYGMOMANOMETER
CERTFIED
40
Connector
20
300
mmHg
MADE IN JAPAN
Figure 2
Wall-Mount (for models 11-675D and 11-675DNL):
Coiled Tube
1. Hold wall-mount plate against the wall at the desired location and
mark the position of the mounting holes for drilling. Drill four (4) holes
and insert the metal wall anchors. Attach the wall-mount plate to the wall
by using the four metal (4) screws (Figure 3).
2. Loosen wing nut on the bottom of the Aneroid and adjust the unit
to the desired angle. Tighten wing nut and slide the wall bracket
into the wall-mount plate (Figure 4).
Figure 4
3. The wall-mounted Omron Aneroid
is now ready for use.
Air Release Valve
Bulb
Figure 3
4
5
ASSEMBLY INSTRUCTIONS
Floor Stand Kit (for models 11-685 and 11-685NL)
ASSEMBLY INSTRUCTIONS
Figure 6
Figure 7
Sphygmomanometer
1. Insert each of the five (5) wheel casters into each of the five (5) legs
of the five-legged base (Figure 6).
160
140
180
120
100
80
60
220
240
240
260
280
2. Insert the larger diameter chrome plated pole into the top of the
five-legged base.
SPHYGMOMNOMETER
CERTIIED
40
20
300
mmHg
M
A
D
E
I
N
J
A
PA
N
3. Insert the large hex-bolt, the large washer, and one small washer from
the bottom center of the five-legged base into the bottom center
of the larger diameter chrome plated pole. Securely tighten the hex bolt.
4. Insert the smaller diameter chrome plated pole into the top of the larger
diameter pole. Insert the black knob into the top of the larger diameter
pole. Set the smaller diameter pole to the desired height and tighten
the black knob.
Small Diameter
Chrome-Plated Pole
5. The floor stand is now complete. To attach the Omron Aneroid to the floor
stand, begin by removing the wing nut connecting the aneroid to the
wall-mount bracket (Figure 7).
Black Knob
6. Insert the small hex nut from the Omron Aneroid and one small washer
from the top of the hole where the wing nut was removed.
Large Diameter
Chrome-Plated Pole
7. While holding the aneroid and small hex nut assembly in one hand, insert
the small hex nut into the top of the smaller diameter chrome plated pole.
Turn the pole counter-clockwise to attach both assemblies.
Securely tighten the assembly.
8. The floor-mounted Omron Aneroid is now ready for use.
Five-Legged Base
Large Washer
On-Site Calibration:
1. Remove the coiled tube from the connector on the underside
of the aneroid.
Wheel Casters
2. Insert the calibration tool (or small flat-head screw driver) into the connector
(from where the coiled tube was removed).
3. Turn the calibration tool until the needle on the front of the gauge is centered
at the bottom of the gauge.
Small Washer
Large Hex Bolt
6
7
|