Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
TEMPERATURE
User’s Guide
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Shop online at
Totalizers & Batch Controllers
pH/CONDUCTIVITY
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
omega.com
e-mail: [email protected]
For latest product manuals:
omegamanual.info
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters
HEATERS
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
TC-08
8 Channel Thermocouple
USB Data Acquisition Module
Quick Start Guide
MONITORING AND CONTROL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
MQS4528/0707
4
Software updates/ replacing lost software
1
Introduction
The latest version of the TC-08 software can be downloaded free of charge from our
web site at:
Thank you for purchasing a TC-08 data acquisition module.
This guide explains how to install the software and product manual using the
supplied CD-ROM.
If you require a new CD, please contact OMEGA Engineering.
The product manual contains detailed information about using the product and its
software. It includes all the information you will need to connect and set up your
product. The product manual is installed in electronic format, but if you would prefer
a paper copy, you can print the PDF files on the CD-ROM.
5
Writing your own software
The CD ROM contains all the manuals and drivers which allow you to develop your
own custom programs easily. Follow section 1.3 to install.
2
General safety warning
We strongly recommend that you read the general safety information below and
also the product-specific safety warning in the product manual before using your
product for the first time. If you do not use the equipment in the manner specified,
then you may impair the protection provided. This could result in damage to your
computer or injury to yourself or others.
6
Input connections
The installed product manuals contain complete descriptions of input connections.
Follow section 1.3 to install.
The product manual is installed on your computer when you install the supplied
software.
7
Technical support
Maximum input range
The OMEGA Engineering web site at:
You can find the maximum input range and, where applicable, overload protection
range in the product manual installed on your computer. Always operate the
product within the specified input range. Operation outside the range of the
overload protection is likely to cause permanent damage to the unit.
also contains regularly updated technical support information. Both the product
manual and the web site contain phone/fax and e-mail contact information for our
technical support team.
Mains voltages
TC-08 data acquisition modules are not designed for use with mains voltages. To
measure mains we recommend the use of a differential probe that is specifically
designed for such measurements.
4
1
Safety grounding
3
Installing the software and manual
Note: Please follow the software installation instructions below BEFORE connecting
The ground of every product is connected directly to the ground of your computer
through the interconnecting cable supplied. This is done in order to minimize
interference. Therefore, always use the supplied cable to attach the product to your
computer.
the hardware product.
3.1 Installing under Windows XP SP2 or Vista
As with most oscilloscopes and data acquisition modules, take care to avoid
connecting the ground input of the product to anything which may be at some
voltage other than ground. If in doubt, use a voltmeter to check that there is no
significant AC or DC voltage between the oscilloscope ground and the point to
which you intent to connect it. Failure to check may cause damage to the product
or computer and could cause injury to yourself or others.
1) Insert the TC-08 software CD into your CD-ROM drive.
2) If Autorun is enabled, the CD will start up automatically.
If so, go to step 6.
3) Press the Start button and select Run...
4) Type d:\TC-08 (where “d:” is your CD-ROM drive).
5) Press the Enter key.
6) Click the Install Application Software button.
7) The program will guide you through the installation.
With temperature converters, take great care when measuring temperatures near
mains equipment. If a sensor is accidentally connected to mains voltages, you risk
damage to the converter or your computer and your computer chassis may become
live.
3.2 Installing USB products
You should assume that the product does not have a protective safety earth.
Incorrect configuration or use on voltages outside the maximum input range can be
hazardous.
USB products are supported only by Windows XP SP2 or Vista.
Install the software before connecting the product to the USB port for the first time
(see section 3.1)
Repairs
Once you have completed the software installation instructions in section 3.1, do
the following:
The unit contains no user-servicable parts. Repair or calibration of the unit
requires specialized test equipment and must be performed by OMEGA
Engineering.
1) Connect the USB cable between the product and one of the USB ports on your
computer.
2) Allow the computer to automatically detect and configure your hardware
product*.
For instructions on how to configure the TC-08 software, see the electronic
manual.
* If Windows displays a warning message about Windows Logo testing you must
click “Continue Anyway” to complete the installation and start using the hardware
product.
3
2
|