Olympus Camera Accessories PT 17 User Manual

Instruction Manual  
For the digital camera  
CAMEDIA D-560 Zoom/D-565 Zoom  
Waterproof Case  
PT-017  
Thank you for buying the Waterproof Case PT-017.  
Please read this instruction manual carefully and use the product  
safely and correctly.  
Please keep this instruction manual for reference after reading it.  
Wrong use may cause damage to the camera on the inside from  
water leakage, and repair may not be possible.  
Before use, perform an advance check as described in this manual.  
 
WARNING  
1.Keep this product out of the reach of babies, infants, and children. There  
is the possibility of occurrence of the following types of accidents.  
・Injury by dropping onto the body from a height.  
・Injury from parts of the body getting caught in parts which open and close.  
・Swallowing of small parts. Please consult a physician immediately if any  
parts have been swallowed.  
・Triggering of the flash in front of the eyes may cause permanent vision  
impairment etc.  
2.Do not store with a battery in the digital camera housed in this product.  
Storage with a battery inserted may lead to leakage of the battery liquid  
and fire.  
3.If leakage of water should occur with a camera installed in this product,  
quickly remove the battery from the camera. There is the possibility of  
ignition and explosion from generation of hydrogen gas.  
4.This product is made of resin. There is the possibility that injuries may be  
caused when it becomes broken because of strong impact with a rock or  
other hard objects. Please handle with sufficient care.  
5.The silica gel and the grease for silicone O-rings for this product are not  
edible.  
CAUTION  
1.Do not disassemble or modify this product. This may cause water leakage  
or trouble. In case of disassembly or modification by persons other than  
those appointed by our company, the guarantee shall not apply.  
2.Do not place this product at locations with abnormally high or abnormally  
low temperatures or at locations with extreme temperature changes. The  
product may deteriorate.  
3.Opening and closing at locations with much sand, dust, or dirt may impair the  
waterproof characteristic and cause water leakage. This should be avoided.  
4.This product has been designed and manufactured for use at a water  
depth within 40 m. Please note that diving to a depth in excess of 40 m  
may cause permanent deformation or damage to the Case and the  
camera inside the Case or may lead to water leakage.  
5.Jumping into the water with the Case in your pocket or in your hand,  
throwing the Case from a boat or ship into the water, and other rough  
handling may cause water leakage. Please handle with sufficient care,  
when handing it over from hand to hand etc.  
Download from Www.Somanuals.cEom-.2All Manuals Search And Download.  
6.If the camera on the inside should become wet because of water leakage  
etc., immediately wipe off all moisture and confirm the operation.  
7.Please remove the O-ring when traveling by air. Otherwise air pressure  
may make it impossible to open the Case.  
8.For safe use of the digital camera in this product, please read the  
"Instruction Manual" for the digital camera carefully.  
9.When sealing this product, take sufficient care that no foreign matter gets  
caught at the O-ring and the contact surfaces.  
Batteries  
Use either one lithium battery pack CR-V3 (LB-01 made by Olympus)  
or two AA alkaline or nickel-hydrogen batteries as the batteries for the  
camera.  
Alkaline batteries can be used only for a small number of photos, and  
their performance also drops with use at low temperatures. If possible,  
avoid use of alkaline batteries as they may become exhausted quickly  
during a dive.  
Take care that the battery electrodes do not become wet. This may cause  
trouble or accidents.  
Carefully read the instruction manual for the camera about other cautions  
regarding batteries.  
Download from Www.Somanuals.cEom-.3All Manuals Search And Download.  
For Prevention of Water Leakage Accidents  
When water leakage occurs while this product is being used, repair of the  
camera housed in this product may become impossible. Please observe the  
following cautions for use.  
1.When sealing this product, make sure that no hairs, fibers, sand particles  
or other foreign matter stick not only to the O-ring, but also to the contact  
surface (flat part of the front cover). Even a single hair or a single grain of  
sand may cause water leakage. Please check with special care.  
Examples for foreign matter sticking to the O-ring〉  
Hair  
Fibers  
Grains of sand  
2.The O-ring is a consumption product. Please replace it at least once a  
year by new one. Also perform maintenance for every use.  
3.Deterioration of the O-ring will progress according to the use conditions  
and the storage conditions. Immediately replace the O-ring by a new one  
if it is damaged, shows cracks, or has lost its elasticity.  
4.At the time of O-ring maintenance, clean the inside of the O-ring groove  
and confirm the absence of dirt, dust, sand, and other foreign matter.  
5.Apply the specified silicone O-ring grease to the O-ring.  
6.The waterproof function is not effective when the O-ring is not installed  
correctly. When installing the O-ring, take care that it does not project  
from the groove and that it is not twisted. Also, when sealing the Case,  
close the lid after confirming that the O-ring has not come out of the  
groove.  
7.This product is an airtight construction made of plastic (polycarbonate).  
When it is left for a long time in a car, on a boat, at the beach, or at other  
places reaching a high temperature, or when it is subjected for a long  
time to uneven external force, it may be deformed and the waterproof  
function may be lost. Pay sufficient attention to temperature control. Also  
do not place heavy objects onto the product during storage or transport,  
and avoid unreasonable storage.  
Download from Www.Somanuals.cEom-.4All Manuals Search And Download.  
8.When the O-ring contact surface is pressed strongly from the outside of  
the Case, or when the Case is twisted, the waterproof function may be  
lost. Take care not to exert excessive force.  
9.Please be sure to perform the advance test and the final test each time  
before using the case.  
If you should notice drops of water or other signs of water leakage while  
.  
taking pictures, immediately stop the dive, remove any water from the  
camera and the product, test according to the item "Final check", and  
confirm whether leakage has occurred or not.  
Handling the Product  
Use or storage of the product at the following locations may cause  
defective operation, defects, trouble, damage, fire, internal clouding, or  
water leakage. Always avoid these locations.  
・Locations reaching high temperatures such as those under direct  
sunlight, in an automobile, etc.  
・Locations with open fire  
・Water depths in excess of 40 m  
・Locations subject to vibrations  
・Locations with high temperatures and much dust or with severe  
temperature changes  
・Locations with volatile substances  
This product is made of polycarbonate resin with excellent impact  
resistance, but it may be damaged by scraping against rocks etc. It also  
may break when it hits hard objects or is dropped.  
This product is not a case to soften impacts to the camera inside the  
product. When this product with a digital camera inside it is subjected to  
impacts or heavy objects are placed onto it, the digital camera may  
become damaged. Please handle the product with sufficient care.  
When the product is not used for a long time, the waterproof performance  
may drop because of deterioration of the O-ring etc. Before use, always  
perform the advance test and the final check.  
Do not apply excessive force to the tripod socket.  
When a flash is used while the Case is being used, shadows may appear  
at the edges of the picture. This is especially notable when taking pictures  
in macro mode on the wide-angle side. Please use a flash after image  
confirmation.  
Download from Www.Somanuals.cEom-.5All Manuals Search And Download.  
Do not use the following chemicals for cleaning, corrosion prevention,  
prevention of fogging, repair or other purposes. When these are used for  
the Case directly or indirectly (with the chemicals in vaporized state), they  
may cause cracking under high pressure or other problems.  
Chemicals which cannot be used Explanation  
Do not clean the Case with alcohol, gasoline, thinner  
Volatile organic solvents,  
chemical detergents  
or other volatile organic solvents or with chemical  
detergents etc. Pure water or lukewarm water is  
sufficient.  
Do not use anticorrosion agents. The metal parts use  
stainless steel or brass, and washing with pure water  
is sufficient.  
Anticorrosion agent  
Commercial defogging  
agents  
Do not use commercial defogging agents. Always  
use the specified desiccant silica gel.  
Use only the specified silicone grease for the silicone  
O-ring, as otherwise the O-ring surface may  
deteriorate and water leakage may be caused.  
Grease other than specified  
silicone grease  
Do not use adhesive for repairs or other purposes.  
When repair is required, please contact a dealer or a  
service station of our company.  
Adhesive  
Do not perform operations other than specified in this instruction manual,  
do not remove or modify parts other than specified, and do not use parts  
other than specified.  
Any troubles in taking pictures or with the equipment resulting from the  
above actions shall be outside the guarantee.  
Our company shall be in no way responsible for accidents involving  
immersion of a digital camera in water.  
Our company shall not pay any compensation for accidents (injury or  
material damage) at the time of use.  
When the enclosure of the balance weight breaks, the metal on the inside  
may corrode. Take care not to damage the enclosure.  
After use, wash the balance weight with pure water and wipe off all  
moisture sufficiently.  
Download from Www.Somanuals.cEom-.6All Manuals Search And Download.  
Contents  
・�  
Introduction  
Please read the following items before use  
E-1  
・�  
E-1  
E-1  
E-3  
E-4  
E-5  
・�  
For safe use  
Batteries  
For Prevention of Water Leakage Accidents  
・�  
・�  
・�  
Handling the Product  
・�  
Contents  
E-7-8  
・�  
1.Preparations  
E-9  
・�  
Check the contents of the package.  
E-9  
E-10  
E-11  
E-11  
E-11  
E-12  
・�  
Names of the parts  
・�  
Install the strap.  
Master the basic operation.  
・�  
・�  
Holding the Case  
How to Press the Shutter  
How to Use the Zoom Lever  
・�  
・�  
E-12  
・�  
2.Advance Check of the Case  
E-13  
・・  
・�  
Advance test before use  
E-13  
・�  
3.Install the digital camera.  
E-14  
・�  
Check the digital camera.  
E-14  
・�  
Loading in the Case  
Which digital cameras can be loaded?  
E-15  
E-15  
E-15  
E-15  
E-16  
E-16  
E-17  
E-17  
E-18  
E-18  
E-19  
E-19�  
・�  
・�  
Open the lens barrier.  
Check the operation of the camera.  
・�  
・�  
Open the Case.  
Load the digital camera.  
・�  
・�  
Insertion of silica gel  
Check the loading status.  
・�  
・�  
Seal the Case.  
Install the special balance weight.�  
Installation and Removal of the LCD Hood  
・�  
・�  
・�  
Mounting and Removing the Lens Cap  
Download from Www.Somanuals.cEom-.7All Manuals Search And Download.  
・�  
Perform the final checks.  
E-20  
・�  
Visual Inspection  
E-20  
・�  
Final Test  
E-21  
・�  
4.Taking Pictures Under Water  
E-22  
・・�  
How to Use the Hand Strap  
E-22  
・・�  
Take pictures carefully.  
Confirm the picture on the LCD monitor  
E-22  
E-22  
E-22  
E-22  
・・�  
・・�  
Quietly press the shutter lever.  
Cautions when using the flash  
・・  
・・�  
・�  
5.Handling After Shooting  
E-23  
・・�  
Wipe off any waterdrop.  
Take out the digital camera.  
Wash the Case with pure water.  
E-23  
・・�  
E-24  
E-25  
E-25  
・・�  
・・  
・・�  
Dry the Case.  
・�  
6.Maintaining the Waterproof Function  
E-26  
・・�  
Remove the O-ring.  
Remove any sand, dirt, etc.  
E-26  
・・�  
E-26  
E-27  
E-28  
E-28  
・・�  
Install the O-ring.  
How to Apply Grease to the O-ring  
・・�  
・・�  
Replace consumable products.  
・�  
7.Appendix  
E-29  
・・�  
Q & A on the use of the PT-017  
After-sale Service  
Specifications  
Diver's Insurance Guide  
Request for returning the user registration card  
E-29  
・・�  
E-34  
E-35  
E-35  
E-35  
・・�  
・・�  
・・�  
Download from Www.Somanuals.cEom-.8All Manuals Search And Download.  
1. Preparations  
Check the contents of the package.  
Check that all accessories are in the box.  
Contact your dealer if accessories should be missing or damaged.  
LCD hood  
(on the body)  
Silica gel  
Silicone grease  
Case body  
LCD hood strap  
Hand strap  
Lenscap  
(Check that the O-ring is normal.)  
Balance weight  
Pick for O-ring removal  
Instruction manual�  
(this manual)  
Warranty card  
Please read before use  
Instruction Manual  
For the digital camera  
CAMEDIA D-560 Zoom/D-565 Zoom  
Waterproof Case  
Read this first about your new  
OLYMPUS Waterproof Case!  
!
PT-017  
Thank you for buying the Waterproof Case PT-017.  
Please read this instruction manual carefully and use the product  
safely and correctly.  
Please keep this instruction manual for reference after reading it.  
Wrong use may cause damage to the camera on the inside from  
water leakage, and repair may not be possible.  
Before use, perform an advance check as described in this manual.  
Download from Www.Somanuals.cEom-.9All Manuals Search And Download.  
Names of the parts  
⑥�  
④�  
W�  
⑦�  
①�  
⑳�  
X�  
③�  
⑧�  
Y�  
Z�  
②�  
③�  
①�  
⑪�  
⑫�  
a`�  
[�  
_�  
\�  
U�  
QP�  
⑨�  
^�  
Palm Grip  
Buckle lock lever ※⑬ LCD monitor button  
Buckle hook ※⑭ OK/Menu button  
J�  
E]SVOR�  
Lens window  
W
X
Y
Z
[
\
]
^
_
`
Grease for silicone O-ring(white cap)  
Silica gel  
Balance weight  
Pick for O-ring removal  
LCD inner hood  
LCD hood  
Diffuser and diffuser cover ※⑮ Arrow Pad  
※⑯ Flash mode button  
O-ring  
※⑥ Shutter lever  
※⑦ Zoom lever  
※⑰ Macro button  
※⑱ Selftimer button  
LCD hood strap  
Shade hood  
Hand strap ring  
Hand strap  
Tripod seat  
Lens ring  
U
V
Rear lid  
Front lid  
Buckle opener  
Lens cap  
Loading guide rail  
LCD monitor window a Lens cap strap  
Note:The Case operation parts marked by※ corresponds to the operation parts of  
the digital camera. When the operation parts of the Case are operated, the  
corresponding functions of the digital camera will operate. For details of the  
functions, refer to the instruction manual for the digital camera.  
Download from Www.Somanuals.Eco-m1. 0All Manuals Search And Download.  
Install the strap.  
Install the strap on the Case body.  
Installation explanation  
Hand strap  
Finished installation  
Hand strap ring  
Please install the strap correctly as shown above. Our company  
shall bear no responsibility for damage etc. caused by dropping  
the Case because of incorrect installation of the strap.  
CAUTION  
Master the basic operation.  
Please master the basic operation of the Case before taking pictures.  
Holding the Case  
Hold the Case securely with both hands, keep your elbows close to your body,  
and hold the Case so that you can confirm the picture on the LCD monitor of  
the digital camera through the LCD monitor window of the Case.  
Good example  
Bad example  
:・ Do not exert excessive force onto the lens window or the lens ring.  
・Take care not to put your fingers etc. over the lens window  
and the flash diffuser.  
CAUTION  
Note  
:・ Use the LCD monitor to confirm your picture. The optical  
viewfinder cannot be used.  
E-11  
 
How to Press the Shutter  
When pressing the shutter  
lever, press it gently, so that  
there will be no movement of  
the camera.  
NoteFor detailed operation of the shutter, refer to the instruction manual  
for the digital camera.  
How to Use the Zoom Lever  
T
W
Zoom operation is possible by  
operating the zoom lever of  
this Case corresponding to  
the zoom lever of the digital  
camera in the Case.  
Download from Www.Somanuals.Eco-m1. 2All Manuals Search And Download.  
2. Advance Check of the Case  
Advance test before use  
This Case has been the subject of thorough quality control for the parts  
during the manufacturing process and thorough function inspections during  
the assembly. In addition, a water pressure test is performed with a water  
pressure tester for all products to confirm that the performance conforms to  
the specifications. However, depending on the carrying and storage  
conditions, the maintenance status, etc., the waterproof function may be  
damaged.  
Before diving, always perform the following advance test and the water  
leakage test after installation of the camera.  
Advance Test  
1.Before installing the digital camera in the Case, immerse the empty  
Case to the intended water depth to confirm that there is no water  
leakage.  
2.Main causes of water leakage are as follows.  
・The O-ring has not been installed.  
・A part of the O-ring or the entire O-ring is outside the specified  
groove.  
・O-ring damage, cracks, deterioration or deformation  
・Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-  
ring groove or the O-ring contact surface on the front lid  
・Damage to the O-ring groove or the O-ring contact surface on the  
front lid  
・When closing the Case, check for catching of the hand strap and  
silica gel after the above causes have been eliminated.  
The most suitable method for checking water leakage is to  
immerse the Case to the intended water depth. When this  
is difficult, water leakage also can be checked at a shallow  
depth with no water pressure. Do not feel that this is  
troublesome, but perform this test.  
CAUTION  
・If the advance test should show water leakage with normal  
handling, stop using the Case and contact your dealer or an  
Olympus service station (listed on the rear page of this  
instruction manual).  
E-13  
 
3. Install the digital camera.  
Check the digital camera.  
Check the digital camera before loading it in the Case.  
Battery Confirmation  
Since the LCD monitor is used for picture confirmation while taking pictures  
under water, the battery life becomes short. Confirm that the remaining  
battery capacity is sufficient. If possible, do not use alkaline batteries, as it  
is quite possible that they will become unusable during a dive.  
NoteIn order to avoid losing shutter chances due to an exhausted battery,  
you should always replace a battery with a fully charged battery  
before each dive.  
Confirmation of the Remaining Number of Pictures to be Taken  
Confirm that the image storage has a sufficient remaining number of  
pictures to be taken.  
Remove the hand strap from the digital camera.  
When a strap is attached to the digital camera, the hand strap must be  
removed.  
When a digital camera is loaded without removing the strap,  
the strap may get caught between the Case lids and may  
cause water leakage.  
CAUTION  
・When removing the strap, handle the digital camera with  
sufficient care. Our company shall not be responsible for  
damage caused by dropping the camera etc.  
Download from Www.Somanuals.Eco-m1. 4All Manuals Search And Download.  
Loading in the Case  
Which digital cameras can be loaded?  
This product (PT-017) is exclusively used for the CAMEDIA D-560 Zoom /  
D-565 Zoom.  
Open the lens barrier.  
The power is switched on when the lens barrier of the digital camera is  
opened. When the camera is left without any operation for at least three  
minutes while the power is switched on, the camera will enter sleep mode  
(standby) and the LCD will go out, and when another five minutes pass  
without any operation, the lens will be retracted. In such a case, cancel the  
sleep mode by operating any button.  
Check the operation of the camera.  
Confirm the operation according to the instruction manual for the digital camera.  
E-15  
 
Open the Case.  
Insert the buckle opener accessory into the buckle opening lever as shown in  
the figure (in direction ①) Pull the buckle opener slowly (in direction ②).  
When not using the buckle opener, hold the buckle opening lever with your  
thumb and index finger from the side and pull it up slowly.  
①�  
②�  
Load the digital camera.  
Quietly load the digital camera into the Case, taking care that the projecting  
part of the zoom lever of the digital camera properly fits into the recessed  
part of the zoom lever of the Case.  
When the setting is insufficient, the loading of the camera  
becomes imperfect and it may not be possible to seal the  
Case or zooming may not function. Insufficient sealing will  
cause water leakage.  
CAUTION  
Note  
:・ At this time, the LCD should be left switched off to save the  
battery.  
Download from Www.Somanuals.Eco-m1. 6All Manuals Search And Download.  
Insertion of silica gel  
Before sealing the Case, insert the accessory silica gel bag (for prevention  
of fogging) between the bottom of the camera and the Case. Insert the bag  
with the glued longer side to the inside.  
Pay attention to the orientation.  
Insert the silica gel all the way at the specified location and  
with the specified orientation. When the orientation is not  
correct, the silica gel bag will be caught when the Case is  
sealed and water leakage will be caused.  
CAUTION  
・ Attempting to seal the Case with the bag inserted only part of  
the way will cause the silica gel bag to get caught by the O-ring  
and water leakage will occur.  
・ Once silica gel has been used, the moisture absorption  
performance will be impaired. Always exchange the silica  
gel when the Case is opened and closed.  
Check the loading status.  
Always perform the following final checks before sealing the Case.  
・Has the silica gel been inserted all the way at the specified position?  
・Has the O-ring at the Case opening part been installed properly?  
・Are the O-ring and the O-ring contact surface on the front lid free of dirt and  
other foreign matter?  
E-17  
 
Seal the Case.  
When the rear lid is closed (quietly, so that the O-ring will not come out of the  
groove), the buckles are engaged with the edge of the rear lid, and the buckle  
lock levers are pushed down in arrow direction, the Case will be sealed airtight.  
Seal the Case by turning both buckle lock levers down in  
arrow direction. When one of the buckles is left open, the  
Case will not be sealed and water leakage will be caused.  
CAUTION  
Install the special balance weight.  
Install the special balance weight to the tripod mounting thread at the  
bottom of the protector. Install the balance weight securely by tightening  
the accessory screw of the balance weight.  
Download from Www.Somanuals.Eco-m1. 8All Manuals Search And Download.  
Installation and Removal of the LCD Hood  
Installation  
Strongly push the mounting projections of the LCD hood as shown in the  
figure into the guides above and below the LCD monitor window.  
Removal  
Remove the mounting projections of the LCD hood from the guides  
above and below the LCD monitor window by widening the LCD hood.  
Installation  
Removal  
Mounting and Removing the Lens Cap  
Fit the lens cap onto the lens ring  
as shown in the figure. Be sure to  
remove the lens cap before  
shooting.  
E-19  
 
Perform the final checks.  
Visual Inspection  
After sealing the Case, check the sealing part of front and rear lid visually  
to confirm that the O-ring is not twisted or out of the groove and that no  
foreign matter has been caught.  
Hairs, fibers, and other narrow items are not very apparent, but they  
may cause entry of water, so that special attention is required.  
When there is no operation of the digital camera for 3  
minutes after it has been installed, the LCD goes out to  
save the battery, and when another 5 minutes pass without  
any operation, the lens is retracted and the camera enters  
into sleep mode (standby status). Return to operation status  
is made when the shutter button or any other button is  
pressed.  
CAUTION  
Download from Www.Somanuals.Eco-m2. 0All Manuals Search And Download.  
Final Test  
The final test after loading the camera is explained below. This is the only way to  
eliminate worry about possible entry of water! Always perform this test. It can be  
performed easily in a water tank or a bathtub. The required time is about five minutes.  
Simple water  
immersion test  
Explanatory  
image  
Hints  
As the Case is transparent,  
waterdrops entering into it can be  
confirmed easily.  
Place the Case  
slowly into the water.  
1
2
3
4
5
6
7
8
In case of trouble with the main O-  
ring, three seconds are enough for  
water to enter. Are there air bubbles  
coming out between the lids?  
Please check carefully.  
At first, immerse the  
Case for only three  
seconds.  
Remove the Case from the water and  
check that no water has accumulated at  
the bottom of the Case.  
Check that no water  
has entered into the  
Case.  
Is there any water trickling down?  
Next, immerse the  
Case for 30  
seconds.  
Check carefully for air bubbles!  
Do not perform any operation yet,  
but just observe.  
Remove the Case from the water and  
check that no water has accumulated  
at the bottom of the Case.  
Check that no water  
has entered.  
Perform very careful confirmation.  
Check carefully for air bubbles!  
Try operation of the buttons used frequently.  
Check carefully for air bubbles!  
If there is still no entry of water,  
everything is OK!  
Next, check by  
immersing for three  
minutes.  
This is very important!  
This is the final check.  
Has the silica gel  
become moist?  
Has the silica gel become moist?  
Please check carefully!  
As the inside can be seen, the inspection for  
entry of water also can be made securely!  
Now everything is  
all right.  
Do not forget the  
balance weight.  
Now everything is all right!  
Have a nice dive!  
Did you remember to attach the  
balance weight?  
E-21  
 
4. Taking Pictures Under Water  
How to Use the Hand Strap  
Pass your hand through the accessory hand strap and adjust the  
length with the stop button.  
Take pictures carefully.  
Confirm the picture on the LCD monitor.  
This Case uses the LCD monitor to confirm the picture. The optical  
viewfinder cannot be used.  
Quietly press the shutter lever.  
When pressing the shutter lever, hold the Case securely with both hands  
and operate the lever quietly to prevent camera shake.  
Cautions when using the flash  
When taking macro pictures on the wide-angle side, the flash light may be  
missing in some parts or the light volume may not be uniform.  
W:Approx. 0.2 m to 3.4 m  
Flash working range  
T:Approx. 0.2 m to 2.0 m  
Depending on the conditions at the time of shooting (clarity of the water,  
suspended matter, etc.), the applicable flash distance may become shorter.  
After taking a picture, display it on the LCD monitor for confirmation.  
(Playback mode is reached by quickly pressing the monitor display button twice  
in a row. Pressing it once more will return the camera to shooting mode.)  
Download from Www.Somanuals.Eco-m2. 2All Manuals Search And Download.  
5. Handling After Shooting  
Wipe off any waterdrop.  
After completing the shooting and  
returning to land, wipe off any  
waterdrop sticking to the Case.  
Use air or a soft cloth not leaving  
any fibers to thoroughly wipe any  
waterdrop etc. from the joint  
between the front and rear lid, the  
shutter lever, the palm grips, and  
the buckles.  
Especially when waterdrops remain between the front and  
CAUTION  
the rear lid, they may spill to the inside when the Case is  
opened. Take special care to wipe off all waterdrops.  
・When opening the Case, take sufficient care that no water  
will drop from your hair or body onto the Case and the  
camera.  
・Before opening the Case, make sure that your hands or  
gloves are free of sand, fibers, etc.  
・Do not open or close the Case at locations where water or  
sand is to be sprayed. When this cannot be avoided  
because you have to exchange the battery or the image  
storage, place a sheet downwind from some object and  
take care that no water or sand is sprayed.  
・Take care not to touch the digital camera or the battery with  
hands wet with sea water.  
Note  
Moisten a towel etc. in advance with pure water and keep it  
in a plastic bag so that you can wipe the salt from your  
hands and fingers before handling the camera.  
E-23  
 
Take out the digital camera.  
Open the Case carefully and take out the digital camera.  
Always place the opened Case with the O-ring side facing  
up. When the Case is placed with the O-ring side facing  
down, dirt or other foreign matter may be attached to the O-  
ring or the O-ring contact surface and may cause water  
leakage during the next dive.  
CAUTION  
・Please read the operation manual for the digital camera for  
the storage of pictures etc.  
・Take special care so that no water drops get onto the  
camera.  
Download from Www.Somanuals.Eco-m2. 4All Manuals Search And Download.  
Wash the Case with pure water.  
After use, seal the Case again after taking out the camera and wash it  
sufficiently in pure water as soon as possible. After use in sea water, it is  
effective to immerse it for a fixed time in pure water to remove any salt.  
Water leakage may be caused when a high water pressure  
is applied locally. Before washing the Case with water,  
remove the digital camera from it.  
CAUTION  
・Operate the shutter lever and various buttons of this product  
in pure water to remove salt adhering to the shaft. Do not  
disassemble for cleaning.  
・ Drying the Case with adhering salt may impair the function.  
Always wash off any salt after use.  
Dry the Case.  
After washing with pure water, use a soft cloth without any salt on it and not  
causing any fibers to wipe off any waterdrop and dry the Case completely at  
a well ventilated location in the shade.  
Do not use hot air from a hair drier or the like for drying and  
do not expose the Case to direct sunlight, as this may  
accelerate deterioration and deformation of the Case and  
deterioration of the O-ring, leading to leakage of water.  
When wiping the Case, take care not to cause scratches.  
CAUTION  
E-25  
 
6. Maintaining the Waterproof Function  
Remove the O-ring.  
Open the Case and remove the O-ring from the Case.  
Removal of the O-ring  
Insert the O-ring removal pick between the O-ring and the wall of the O-  
ring groove.  
Move the tip of the inserted pick under the O-ring. (Take care not to  
damage the O-ring groove with the tip of the pick.)  
Hold the O-ring with your fingertips after it has come out of the groove and  
remove it from the Case.  
Remove any sand, dirt, etc.  
After visually checking that dirt has been removed from the O-ring, checking  
for attached sand and other foreign matter, as well as for damage and cracks  
can be done by squeezing the entire circumference of the O-ring lightly with  
your fingertips.  
Download from Www.Somanuals.Eco-m2. 6All Manuals Search And Download.  
Use a clean cloth (that doesn't shed fibers), a toothbrush, tissue paper or the  
like, to remove any foreign matter from the O-ring groove.  
When a mechanical pencil or a similar other sharp object is  
used to remove the O-ring or to clean the inside of the O-  
ring groove, the Case and the O-ring may be damaged and  
water leakage may be caused.  
CAUTION  
・When the O-ring is checked with the fingertips, take care not  
to stretch the O-ring.  
・Never use alcohol, thinner, benzene or similar solvents or  
chemical detergents to clean the O-ring. When such  
chemicals are used, it is likely that the O-ring will be  
damaged or that its deterioration will be accelerated.  
Install the O-ring.  
Confirm that no foreign matter is attached, apply a thin coat of the accessory  
grease to the O-ring, and fit the O-ring into the groove. At this time, confirm  
that the O-ring does not stick out from the groove.  
E-27  
 
How to Apply Grease to the O-ring  
In order to apply a thin coat of silicone grease uniformly to the O-ring, squeeze  
about 5 mm from the tube of the accessory grease into a clean plastic bag and  
knead the bag well. Then put the O-ring into the bag and knead it well to apply  
the grease uniformly to the O-ring. When the plastic bag is clean, it can be  
used repeatedly. A size of about 10 cm x 20 cm is suitable for the plastic bag.  
Always perform maintenance of the waterproof function  
even when the Case has been opened to exchange the  
battery or the image storage during shooting. Neglecting  
this maintenance may become the cause of water leakage.  
・When the Case is not to be used for a long time, remove the  
O-ring from the groove to prevent deformation of the O-ring,  
apply a thin coat of silicone grease, and store it in a clean  
plastic bag or the like.  
CAUTION  
・When drying is done with salt attached, it is likely that a  
function impairment will be caused. After use, always wash  
off any salt.  
Replace consumable products.  
・The O-ring is a consumable product. Independent of the number of times  
the Case is used, it is recommended that the O-ring should be replaced by  
a new one at least once a year.  
・Deterioration of the O-ring is accelerated by the use conditions and the  
storage conditions. Replace the O-ring even before a year has passed if it  
shows signs of damage, cracking or loss of elasticity.  
Note: Please use original Olympus products for the silicone O-ring  
grease, the silica gel, and the O-ring. These consumable products  
also can be purchased at an Olympus service station.  
Download from Www.Somanuals.Eco-m2. 8All Manuals Search And Download.  
7. Appendix  
Q & A on the use of the PT-017  
Which digital cameras can be used?  
The PT-017 is only for the models D-560 Zoom / D-565 Zoom.  
What cautions must be observed when loading the digital camera into  
the Case?  
Pay special attention to the following items when loading the camera  
into the Case.  
(1Check that the remaining capacity of the battery in the digital camera is sufficient.  
This should be checked as the LCD monitor is used under water, and  
the battery consumption becomes faster.  
(2Check the remaining number of pictures on the image storage.  
Please use a card with a sufficient remaining number in order to reduce  
the number of times the Case has to be opened and closed.  
(3Remove the strap from the digital camera.  
When the camera is loaded without removing the strap, the strap may get  
caught when the Case is sealed and this will cause water leakage.  
(4Before sealing the Case, confirm that the O-ring has been installed  
properly in the groove in the rear lid of the Case.  
(5Confirm that the O-ring and the O-ring contact surface on the front lid  
are free of dirt, hairs, and other foreign matter.  
(6Insert the silica gel for defogging. Please use silica gel for the Olympus Case.  
(7Finally install the special balance weight to the tripod mounting thread.  
What cautions must be observed when using and storing the Case?  
Pay special attention to the following items.  
(1When the O-ring contact surface is pressed strongly from the outside of  
the Case, or when the Case is twisted, the waterproof function may be  
impaired and water leakage may be caused.  
(2When the Case is used, left or stored at the following locations, defective  
operation or trouble may be caused. Always avoid such locations.  
(aPlaces where the Case can reach high temperatures under direct  
sunlight or in a car, places with extremely low temperatures, and  
places with extreme temperature variations  
(bPlaces with open fire  
(cPlaces with volatile substances  
(dPlaces with vibrations  
E-29  
 
(3In case of the following handling with a camera loaded into the Case,  
trouble or breakage may be caused for the Case and/or the loaded  
camera. Always avoid such handling.  
(aHitting other objects  
(bDropping  
(cPlacing heavy objects on top of the Case  
(4When the Case is not used for a long time, trouble from formation of  
mold etc. may be caused. Before use, confirm the operation of all  
operation parts and perform the advance test and the final test.  
What cautions must be observed when opening and closing the Case?  
Pay special attention to the following items.  
(1Do not open and close the Case at locations with water spray or sand  
spray.  
(2Wipe off all waterdrops from the gap between the front lid and the rear  
lid and around projections and recesses such as the buckles. When this  
is not done, entry of waterdrops into the Case is to be feared at the time  
of opening and closing.  
(3When opening the Case, take care that no water will drip from your hair  
or body into the Case or onto the camera.  
(4When the Case is open, check that there is no attachment of sand,  
fibers or other foreign matter to the O-ring and the O-ring contact  
surface on the front lid.  
(5Do not touch the camera or the image storage with your hands to which  
sea water is sticking.  
(6If you should detect waterdrops or other signs of water leakage while  
shooting, immediately end the dive, perform the water leakage test  
again, and confirm that there is no leakage. If the camera is wet, wipe  
off any moisture and check the operation.  
How should the Case be handled after use?  
After use, take out the camera as soon as possible and wash the Case  
with pure water. In case of use in the ocean, it is effective to immerse  
the Case for a certain time in pure water to remove any salt. Operate  
the buttons and levers under water to turn the shafts and wash off any  
salt. After washing, use a dry cloth without any salt on it to wipe off any  
moisture and dry the Case in the shade. Do not use hot air from a hair  
drier or the like and do not dry the Case under direct sunlight. Exposure  
to high temperatures or direct sunlight may cause deformation,  
discoloration or breakage of the Case and deterioration of the O-ring.  
Download from Www.Somanuals.Eco-m3. 0All Manuals Search And Download.  
Wipe the inside of the Case with a soft cloth not causing any fibers.  
Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean  
the O-ring groove and the O-ring contact surface in the same way and  
then dry them. When an object with a sharp tip is used to remove the O-  
ring from the groove, the O-ring may be damaged and water leakage  
may be caused. Always use the accessory pick for O-ring removal.  
How should I take pictures under water?  
Please observe the following items for shooting under water.  
(1Fix the Case with the accessory hand strap to your wrist.  
(2When you place a finger onto the lens window, the finger will appear in  
the photo. Pay attention to the position of your fingers when holding the  
Case.  
(3When pressing the shutter lever, hold the Case securely with both  
hands and operate the lever quietly to prevent camera shake.  
(4Look through the LCD monitor window on the rear of the Case to  
confirm the picture and then press the shutter lever. Please note that  
the optical viewfinder cannot be used, When the LCD monitor is used,  
the battery is exhausted earlier. In order to avoid losing shutter chances  
due to an exhausted battery, please always replace a battery with a fully  
charged battery before each dive.  
How can I check for water leakage?  
For confirmation, perform the advance test and the final test after  
loading the camera. The advance test with immersing the Case without  
the camera to the intended use depth to check for water leakage is the  
most accurate test, but when this is difficult, it is safer to perform this  
test even at a depth of 1 m or in a bathtub. The final test also can be  
performed in a bathtub or a bucket.  
What are the causes for entry of water?  
The main causes for the entry of water are shown below. Please check  
them most carefully.  
(1Forgetting to install the O-ring  
(2The O-ring is partly or completely outside the groove.  
(3Damage, deterioration, or deformation of the O-ring  
(4Sand, fibers, hair or other foreign matter on the O-ring  
(5Sand, fibers, hair or other foreign matter on the O-ring groove or the O-  
ring contact surface  
E-31  
 
(6Catching of the strap, the bag of silica gel, etc. at the time of sealing the  
Case  
(7Throwing the Case from a boat into the water, jumping with the Case into  
the water, or other sudden application of strong forces onto the Case. When  
entering the water, hand the Case over quietly or avoid impacts in other  
ways.  
What are the important points for O-ring maintenance?  
Please observe the following items.  
(1Never use alcohol, thinner, benzene or similar organic solvents or chemical  
detergents to clean the O-ring. When such chemicals are used, it is to be  
feared that the O-ring will be damaged or that its deterioration will be  
accelerated.  
(2Use the original Olympus silicone O-ring grease (white cap). The grease  
attached to Cases up to PT-008 (red cap) and the grease of other  
companies are not suitable for this silicone O-ring, and use of such grease  
may cause deterioration of the surface and impairment of the waterproof  
function.  
(3In order to avoid deformation of the O-ring when the Case is not used for a  
long time, remove the O-ring from the Case, apply a thin coat of the  
special grease, and store the O-ring in a clean plastic bag. For reuse,  
confirm that the O-ring is free of damage and cracks, that it has sufficient  
elasticity, that the surface is free of stickiness and other abnormalities, and  
use it after applying a thin coat of the special grease. Excessive  
application of grease does not improve the waterproof function or the  
permissible withstand pressure. However, it may facilitate attachment of  
sand, dirt, etc.  
A thin, uniform coat produces the best result.  
(4The O-ring is a consumable product. Replace it at least once a year.  
(5Deterioration of the O-ring is accelerated by the use conditions and the  
storage conditions. Replace the O-ring immediately by a new one if it  
shows signs of damage, cracking or loss of elasticity.  
What are the important points for Case maintenance?  
Please observe the following items.  
(1Never use the following chemicals for cleaning, corrosion protection,  
defogging, repair or other purposes.  
・Never use alcohol, thinner, benzene or similar volatile organic solvents or  
chemical detergents to clean the Case. Pure water or lukewarm water is  
sufficient for cleaning.  
Download from Www.Somanuals.Eco-m3. 2All Manuals Search And Download.  
・Do not use anticorrosion agents on the metal parts. The metal parts are  
made of aluminum, brass or stainless steel. Cleaning with pure water is  
sufficient.  
・Do not use commercial defogging agents. Always use the original  
Olympus defogging silica gel.  
・Do not use adhesive for repairs or other purposes. When repair is  
required, please contact a service station of our company or your dealer.  
Please tell me about repairs.  
Please contact a service station of our company or your dealer, if repair  
should be necessary. Do not try to repair, disassemble or modify the  
Case yourself. Repair, disassembly or modification by you or third  
parties not authorized by Olympus invalidates the guarantee.  
What are the model numbers of the PT-017 accessories?  
The following accessories are being sold.  
(1O-ring for the PT-017 body (POL-017): This is a silicone rubber O-ring  
packing to be installed in the PT-017 body to make it waterproof. O-rings for  
other Case models cannot be used.  
(2Silicone O-ring grease (PSOLG-1): This is a special grease for silicone  
O-ring maintenance.  
(3Silica gel (SILCA-5): This is a desiccant used to prevent fogging of the  
glass parts of the Case. The quantity is five bags.  
(4LCD hood (PFUD-04): This hood is installed on the LCD monitor  
window of the Case to make it easier to see the LCD monitor of the  
camera.  
(5Balance weight for PT-017 (PWT-017): This is a weight intended to  
bring the Case close to neutral buoyancy in sea water. Under  
consideration of the environment, no lead is used.  
※ You can order in large computer shops and camera mass sale stores.  
※Please contact your dealer or a service station of our company when  
replacement is required. Replacement will be made against payment.  
E-33  
 
After-sale Service  
You will receive the guarantee card from your dealer. Please make sure  
that the dealer's name, the date of purchase, etc. have been entered. If  
they have not been entered, immediately ask your dealer to have them  
entered. Read the guarantee conditions carefully and keep the guarantee  
card at a safe location.  
Please contact your dealer or one of the service stations of our company  
listed in this instruction manual for questions on after-sale service for this  
product or in case of defects. In case of a defect of this product, occurring  
within one year after the date of purchase and with handling according to  
this instruction manual, repair based on the conditions specified in the  
guarantee card is performed free of charge.  
Payment is required for repairs after expiration of the guarantee period and  
for trouble caused by problematic handling by the customer even during  
the guarantee period.  
Our company keeps repair parts for this product for approximately five  
years after the end of production of the product. Accordingly, in principle  
repairs are accepted during this period. As repair may be possible even  
after this period, please contact your dealer or a service station in your  
neighborhood.  
●Warranty is limited to and valid only in the region of intended distribution .  
Incidental damages from defects of this product (expenses required for  
diving, shooting expenses, loss of profit from photos, etc.) shall be  
excluded from the guarantee. In addition, transport expenses etc. related  
to repair shall be paid by the customer, independent of whether they are  
incurred during or after the guarantee period.  
Download from Www.Somanuals.Eco-m3. 4All Manuals Search And Download.  
Specifications  
Available models  
Olympus digital camera  
CAMEDIA D-560 Zoom / D-565 Zoom  
Pressure  
resistance  
Depth of up to 40 m  
Main materials  
Body: Transparent polycarbonate  
Buckles: Stainless steel  
Grip/Shutter lever: Red polycarbonate  
Lens window: FL glass  
Lens ring: Aluminum  
Operation buttons: Stainless steel Nickel-plated brass  
Dimensions  
Weight  
Width 148 mm x height 102.6 mm x thickness 106 mm  
(projections not included)  
390 g (LCD hood not included)  
※We reserve the right to change the external appearance and the  
specifications without notice.  
Diver's Insurance Guide  
We recommend to subscribe to diver's insurance for water leakage.  
Please see enclosed driver's insurance application as possible  
choice to subscribe to.  
Request for returning the user registration card  
Please fill out the enclosed user registration card and mail it to us.  
E-35  
 
MEMO  
 
OLYMPUS OPTICAL CO., LTD.  
San-Ei Building, 22-2, Nishi Shinjuku 1-chome, Shinjuku-ku, Tokyo, Japan  
Customer support (Japanese language only): Tel. 0426-42-7499 Tokyo  
OLYMPUS AMERICA INC.  
Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 631-844-5000  
Technical Support (USA)  
Phone customer support: Tel. 1-888-553-4448 (Toll-free)  
Our phone customer support is available from 8 am to 10 pm  
(Monday to Friday) ET  
OLYMPUS OPTICAL CO. (EUROPA) GMBH.  
Premises/Goods delivery: Wendenstrasse 14-18, 20097 Hamburg, Germany  
Tel. 040-23 77 33  
Letters: Postfach 10 49 08, 20034 Hamburg, Germany  
European Technical Customer Support:  
Please visit our homepage http://www.olympus-europa.com  
or call our TOLL FREE NUMBER : 00800 - 67 10 83 00  
for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg,  
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom  
Please note some (mobile) phone services/provider do not permit access or  
request an additional prefix to +800 numbers.  
For all not listed European Countries and in case that you can’t get connected  
to the above mentioned number please make use of the following  
CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899  
Our Technical Customer Support is available from 9 am to 6 pm MET (Monday to Friday)  
© 2003 OLYMPUS OPTICAL CO., LTD.  
0603 2MJ  
Printed in Japan  
VT597701  
 

MTD Lawn Mower Series 400 User Manual
NEC Laptop Versa Series User Manual
NETGEAR Network Hardware WN604 100NAS User Manual
NETGEAR Network Router MBRN3000 100NAS User Manual
Olympus Camera Accessories Infinity Stylus User Manual
Omron Healthcare Blood Pressure Monitor HEM 705CP User Manual
On Q Legrand Home Security System HMS 1100 User Manual
Panasonic Fax Machine DX 800 User Manual
Panasonic Flat Panel Television CT L2000 User Manual
Panasonic Smoke Alarm 1826 User Manual