models Nm200WH • Nm200Al
Page ꢀ
Nm200 series
system iNstAllAtioN
reAd ANd sAve tHese iNstructioNs
•
Do not connect CAT5 wire if you are unsure of its termination
point. Connecting a door station to a remote station may
result in system damage.
cAutioN
to reduce tHe risk of fire, electric sHock, or
iNjury to persoNs, observe tHe folloWiNg:
•
•
•
Do ensure that all rough-in instructions have been followed
before power is applied to the NM200 system.
1. Read all instructions carefully before installing or using the
NM200 System.
Do not splice cables. Splices are unreliable and defeat signal
isolation properties of the cable.
2. The NM200 must be installed by a qualified dealer or installer,
Do not attach devices unauthorized for use with this system.
Authorized devices include:
and must conform to all local building and electrical codes.
3. For continued protection against risk of fire replace the fuse
in the power switch module only with the same type 3 Amp,
250 Volt fuse.
Audio components connected via a line level input
NC300 6-disc CD player
•
If extra cables have been run for future speaker additions,
care must be taken to ensure these cables are not connected
to the NM200 master unit. Un-terminated cables (no station)
connected to the NM200 master may cause electronic
feedback that will damage the master unit.
4. Adhere to all warnings on the NM200 and in these instructions.
Follow all operating and installation instructions.
WArNiNg
•
Do not over-tighten the screws for the remote stations or the
master as the plastic face panels may crack or strip out.
tHese iNstAllAtioN ANd serviciNg iNstructioNs
Are for use by quAlified persoNNel oNly. to
reduce tHe risk of electric sHock, do Not
performANyserviciNgotHertHANtHAtcoNtAiNed
iN tHe operAtiNg iNstructioNs uNless you Are
quAlified to do so.
•
Use only NuTone certified replacement parts and have them
installed by a qualified dealer or installer. Unauthorized
substitutions can result in fire, electric shock, or other
hazards.
•
Upon completion of any service or product repair, have
the dealer or installer conduct a safety check to ensure the
system is in proper operating condition.
•
Do not attempt to service the NM200 yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
•
Use only a damp cloth to clean the NM200 master and remote
stations. Do not use liquid cleaners or aerosol cleaners.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of shock to persons.
iNstAllAtioN
To ensure that the homeowner receives the high-quality music
and voice reproduction that the system is designed to deliver, it
is important that each step of the installation be done carefully.
In the event you need troubleshooting assistance, please call
our technical staff at 1-888-336-6151.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
•
•
•
•
•
•
Locate the system away from heat sources such as radiators,
heat registers, stoves, or other heat producing products.
The installation should be made after the application of wall
covering material.
Do not locate the NM200 master or remote stations in an
outside wall.
Tools required:
•
•
•
•
#2 Phillips screwdriver
Standard flat head screwdriver
Wire stripper/cutter
Level
Do not locate the NM200 to moisture. Doing so can create
fire or shock hazards and void the warranty.
Do not place the NM200 master or remote stations in any
wall cavity with any other electrical wiring in the cavity.
Install the NM200 system after the application of the wall
covering material.
iNstAlliNg tHe remote stAtioNs
Collect all the connectors included in the remote station packages
and place them in the master rough-in for use later. At each
remote station location, strip approximately 4 inches of jacket
Do not expose the outdoor remote station speakers to
significant water contact. The outdoor remote speakers are
weatherproof but not water proof. Continuous direct water
exposure will cause system problems.
models Nm200WH • Nm200Al
Page ꢂ
Nm200 mAster stAtioN iNstAllAtioN
Gather all remote station and door station cables and cut cable
ends to the same length approximately 12 inches from entry
point into master rough-in. Make sure that all cables remain
properly labeled. Strip approximately 2” of jacket from each of
the CAT5 cables. Untwist the individual wire pairs. Insert each
wire pair into the correct connector location and close connector.
Please see figure below. Insert each cable connector into its
proper location on the NM200 master.
Make sure that the outdoor remote station is connected into
the outdoor remote stations cables location only. If you are
connecting two outdoor remote stations, use the screw terminal
connectors provided with the NPS200 for the outdoor remote
station. Connect both outdoor remote stations cables into one
screw terminal connector.
If the NM200 system has more than 9 remote stations, some
station selector switches will control two remote stations. Do
not exceed more than 15 total speakers on the system. This
limitation does not include door stations. The station location
can be noted on the inside of the front access panel on the left
side of the NM200 master.
Connect the red and black wires of the door station cables to the
red and black door speaker terminals on the NM200 master as
shown below. Insulate the bare wires using some of the jacket
material to prevent shorting to the circuit board. Connect this
wire to terminal labeled shield.
Connect all orange wires from the door stations to the common
terminal on the NA3003C or NA3008C.
Connect each yellow wire to a note selection terminal on the
NA3003C or NA3008C. Do not connect more than one yellow
wire per note terminal.
it is important to verify all cable run locations prior
to connecting if they were not labeled at the rough-
in. incorrectly connecting cables to the master,
remote stations or door stations may result in system
damage.
Plug in the modular chime plug to the 4 pin connector labeled as
CHIME on the NM200 master unit as shown.
Mounting the Chime Module
Install the optional NA3003C or NA3008C chime module in the
master rough-in by pressing the chime module over the 4 plastic
standoffs attached to the rough-in as shown. Please refer to the
Suspend the master unit from the master rough-in by looping the
support wire assembly (thick green wire) over the hook at the
top of the rough-in. Be careful not to damage the wall surface.
models Nm200WH • Nm200Al
Page ꢃ
Antenna connection
poWeriNg up tHe Nm200
After all connections have been made, insert the power plug into
the transformer and secure the master to the rough-in using the
2 screws provided. If using the NF200C frame with a NC300
CD player, install the master unit over the frame. Do not over
tighten the screws as the plastic may distort or crack. Install the
speaker panel on the master.
Connect the FM dipole coax antenna lead “F” connector to the
FM 75 Ohm “F” connector on the NM200 master as shown in the
previous figure. Connect the orange AM antenna wire to the AM
terminal on the master.
door release connection
Please be careful to only apply pressure on the speaker panel
at the corners and not in the middle. Check all functions by
following the guidelines in the Owners Manual shipped with
the master unit. If any difficulties are encountered, recheck all
connections. If after reviewing these instructions and you are
unable to resolve any problems, contact technical support at 1-
888-336-6151.
To use the door release, connect the 18 gauge low volt-
age cables from the remote power transformer and the door
release striker. The 24 Volt/2 Amp dry contact switch closure
may also be used for home automation or security panel panic
alarm interface.
Note: The door release operation may only be used for one type
of function per application.
external Audio sources
Plug in the RCA™ phono plugs to the AUX jacks as marked for
the source audio equipment.
models Nm200WH • Nm200Al
Page ꢄ
Two Year Limited Warranty
WARRANTY OWNER: Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of
two (2) years from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this two year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS
WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This
warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other
than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the two year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the
above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT
USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This war-
ranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identi-
fication and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.
Date of Installation
Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE - CONTACT:
Rev. 08/2007
Garantie limitée de deux ans
GARANTIE DU PROPRIÉTAIRE: Broan-NuTone garantie à l’acheteur original de ses produits que ces derniers seront exmpts de tout défaut de matériaux et de fabrication pour une période de deux (2) ans à
compter de la date d’acha. AUCUNE AUTRE GARANTIE, IMPLICITE OU EXPRESSE, N’EST DONNÉE, Y COMPRIS, MAIS SANS S’Y LIMITER, GARANTIE DE MARCHANDIBILITÉ OU D’ADAPTATION
À UN USAGE PARTICULIER.
Pendant cette période de deux ans, Broan-NuTone procédera au remplacement ou à la réparation sans aucuns frais, mais à sa propre discrétion, de tout produit ou pièce jugé défectueux dans le cadre d’une
utilisation normale. CETTE GARANATIE NE VISE PAS LES DISPOSITIFS D’AMORCAGE NI LES TUBES DES LUMINAIRES FLUORESCENTS. Cette garantie ne couvre pas (a) l’entretien et le service courants
ni (b) les produits et les pièces ayant fait l’objet du’n usage abusif, de négligence, d’un accident, d’un entretien ou d’une réparation non appropriée (par du personnel non autorisé par Broan-NuTone) d’une mauvaise
installation ou d’une installation non conforme aux directives d’installation fournies.
La durée de toute garantie implicite est limitée à la période de deux ans précisée pour la garantie expresse. Certains états ne reconnaissent pas les restrictions relatives à la durée des garanties implicites; il se
pourrait donc que cette restriction ne s’applique pas dans votre cas.
LE REMPLACEMENT OU LA RÉPARATION PAR BROAN-NUTONE, À SA PROPRE DISCRÉTION, DE TOUT PRODUIT OU PIÈCE DÉFECTUEUX CONSTITUE LE SEUL REMÈDE DE L’ACHETEUR
EN VERTU DE CETTE GARANTIE. BROAN-NUTONE NE PEUT ÊTRE TENUE RESPONSABLE DES DOMMAGES INDIRECTS, CONSÉCUTIFS OU SPÉCIAUX ATTRIBUABLES À UTILISATION OU AU
RENDEMENT DU PRODUIT. Certains états ne reconnaissent pas les restrictions ni les exclusions relatives aux dommages indirects, consécutifs ou spéciaux; il se pourrait donc que cette restriction ne s’applique
pas dans votre cas. La présente garantie vous accorde des droits spécifiques, mais vous pourriez aussi avoir d’autres droits en fonction de l’état dans lequel vous résidez. Cette garantie remplace toute autre
garantie donnée précédement.
SERVICE SOUS GRANTIE: Pour être admissible au service sous garantie, vous devez (a) aviser Broan-NuTone, à l’adresse ou au numéro de téléphone ci-dessous, (b) fournir le numéro du modèle et
la description de la pièce et (c) décrire la nature défaut de la pièce ou du produit. Au moment de la demande de service sous garantie, vous devez fournir une preuve de la date d’achat originale.
Date d’installation
Entrepeneur ou installateur
N° de modèle et description du produit
POUR OBTENIR DE L’ASSITANCE OU DU SERVICE - CONTACTEZ:
Rev. 08/2007
Garantia limitada de dos años
GARANTÍA DEL PROPIETARIO: Broan-NuTone garantiza al comprador consumidor original de sus productos, por el período de dos (2) años desde la fecha original de compra, que tales productos están libres de
defectos en material y mano de obra. NO HAY OTRAS GRANTÍAS, EXPRESADOS O SOBREENTENDIDAS, INCLUYENDO, PERO NO LIMITADAS A, GRANTÍAS NO EXPRESADAS DE MERCHNTIBILIDAD
O ADAPTABLES A UN PROPÓSITO EN PARTICULAR.
Durante este período de dos años, Broan-NuTone reparará o reemplazará a su opción y sin costo, cualquier producto o parte que se encuentre defectuoso bajo condiciones normales de uso y servicio. ESTA
GARANTÍA NO CUBRE A LOS ARRANCADORES PARA LÁMPARAS FLUORESCENTES O A LOS TUBOS FLUORESCENTES, FILTROS, DUCTOS, TAPAS DE TECHO, TAPAS DE PARED Y OTROS
ACCESORIOS PARA CANALIZACIÓN. Esta granatía no cubre (a) Mantenimiento y servicios normales (b) Productos o partes sujetos al mal uso, negligencia, accidente, mantenimiento inadecuado o reparaciones
(port otros ajenos a Broan-NuTone), instalación defectusoa o a una instalación contraria a las instrucciones de instalación recomendadas.
La duración de cualquier garantia no expresada está limitada a un periodo de dos años según se especifica en la garantia expresada. Algunos estados no permiten limitación en cuanto a la duración de una grantia
no expresada, por lo que la limitación arriba indicada puede que no se apliqué a Ud.
LA OBLIGACIÓN DE BROAN-NUTONE DE REPARAR O REEMPLAZAR A SU OPCIÓN, SERÁ EL ÚNICO Y EXCLUSIVO RECURSO QUE TENDRÁ EL COMPRADOR BAJO ESTA GARANTÍA. BROAN-
NUTONE NO SERÁ RESPONSABLE POR DAÑOS INCIDENTALES, CONSECUENTES O ESPECIALES QUE RESULTEN A CONSECUENCIA O SEAN INDEPENDIENTE DEL USO O DESEMPEÑO DEL
PRODUCTO. Algunos estados no permiten la exclusión o limitación de daños incidentals o consecuentes, de modo que la limitación o exclusión arriba indicada pueda que no se aplique a Ud. Esta garantia le
proporciona derechos legales especificos, y Ud.puede tener otros derechos, los cuales varían de estado a estado. Esta garantias reemplaza a todas las garantías anteriores..
SERVICO DE GARANTÍA: Para tener derecho al servicio de garantía, Ud. debe (a) Notificar a Broan-NuTone a la dirección o el número de teléfono abajo, (b) indicar el número de modelo y la identifación
de la party y (c) describir la naturaleza de cualquier defecto en la producto o parte. Al momento de solicitor el servicio por la garantía, Ud. debe presentar la evidencia de la fecha original de compra.
Fecha de la instalación
Constructor o instalador
Número de modelo y descripción del producto
SI NECESITA ASISTENCIA O SERIVIVIO - CONTACTO:
Rev. 08/2007
|