M O
D
E L
SVL-4AB
SVL-4AB
SPEAKER SELECTION/VOLUME CONTROL SYSTEM
WITH A/B AMPLIFIER INPUTS
I N S T A L L A T I O N & O P E R AT I O N G U I D E
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Feat ures and Benefit s
The SVL-4AB offers a number of improvements over other
speaker selector/volume controllers:
● Amplifier A/B Switching—The SVL-4AB provides amplifier
switching for each pair of speakers. The switches are
“break-before-make“ and simultaneously switch both
grounds and hots. This allows any two amplifiers to safely
and reliably operate simultaneously.
TECH
SUPPORT
HOTLINE
If you have
questions regarding
the operation of the
Niles SVL-4AB, con-
tact your local Niles
dealer or Niles
● The SVL-4AB uses 12-position POP-FREE volume controls
which are superior to 10-position designs. You get a
broader range of adjustment —there are 10 steps of atten-
uation instead of 8. Steps 11-6 attenuate -3 dB per step;
steps 5-2 are 6 dB per step. Step 12 is "full-on" and step 1
is "full-off".
Customer Service at
1-800-289-4434.
● Greater dynamic range —you get 42 dB of total attenua-
tion instead of the usual 20 or 30 dB.
● Pre-printed Room Labels are included for easy identification
of speaker ON/OFF buttons.
● Isolated left and right channel ground returns make the
SVL-4AB compatible with all types of amplifiers.
2
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
● Rear panel switches for constant or selectable impedance
protection for each amplifier. You can use constant protec-
tion on one of your two amplifiers and manual protection
for the other.
● Self-cleaning, silver-plated switch contacts assure many
years of trouble free use.
● Printed circuit board design assures high reliability.
● Two-piece removable connectors greatly simplify installa-
tion and hookup. All wiring can be attached directly to the
connectors before installing them in the SVL-4AB.
● 100% tested, electronically and acoustically, for frequency
response, distortion and power handling.
● Standard 17" width allows the SVL-4AB to stack neatly
with other standard size components.
● May be used with 4, 6, or 8-ohm speaker systems.
● Ideal for both home and commercial sound installations.
● Power handling: 100 watts/channel continuous music
power.
● Frequency response: 20 Hz to 20 kHz +/-1.2 dB.
● Ten year parts and labor warranty.
● Proudly made in the USA.
3
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion Considerat ions
SVL-4AB Power Handling
TOOLS
REQUIRED
The SVL-4AB is designed for use with receivers or amplifiers
having a maximum power output of 100 watts per channel at
8 ohms. Damage caused by the use of higher-power receivers
or amplifiers will void the warranty. Consult your Niles dealer
or receiver/amplifier manufacturer if you are uncertain about
the power rating of your receivers or amplifiers.
• 1/8" Standard
Slotted Screwdriver
• Wire Stripper
IMPORTANT: DO NOT USE THE SVL-4AB WITH AMPS OR
RECEIVERS RATED AT MORE THAN 100 WATTS PER CHANNEL
RMS AT 8 OHMS.
IMPORTANT
DO NOT use the
SVL-4AB with amps
or receivers rated
at more than 100
watts per channel
RMS at 8 ohms.
Amplifier Impedance Load
As more pairs of speakers are parallel connected to a receiver
or amplifier, the overall system impedance becomes lower.
For example, if two pairs of 8-ohm speakers are connected in
parallel, the impedance will be 4 ohms; two pairs of 4-ohm
speakers in parallel become 2 ohms, and so on.
Most receivers or amplifiers are not rated for use below a
4 ohm load. Most m anufacturers do not recom m end
connecting more than two pairs of speakers without using
some form of impedance correction.
4
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
The SVL-4AB includes impedance correction circuitry which
protects each of your receivers or amplifiers from low imped-
ance loads. The circuitry assures that both of your receivers or
amplifiers will recognize a safe operating load, even when one
amplifier is playing all four speaker pairs at the same time.
The actual impedance load the SVL-4AB presents to each of
your receivers or amplifiers will vary, depending on how
many speaker pairs are playing, and the impedance rating of
each speaker. If you have four pairs of 8-ohm speakers play-
ing from one of your receivers/amplifiers, the SVL-4AB will
present a 4.5 ohm impedance load to it. With four pairs of 4-
ohm speakers playing, the load drops to slightly under 4
ohms.
"TECH TIP"
It is recommended that you use the SVL-4AB with receivers
or amplifiers that are capable of driving a 4-ohm load.
Consult your Niles dealer, or the receiver/amplifier manufac-
turer, if you are uncertain about the capabilities of the
receiver/amplifier.
Wire size is
expressed by it's
AWG (American
Wire Gauge)
number. The lower
the AWG number,
the larger the
Type of Speaker Wire
wire,
i.e., 12 AWG wire is
physically larger
For most applications, we recommend you use 16 or 18
gauge stranded copper speaker wire for the SVL-4AB connec-
tions. For wiring runs longer than 80 feet, 14 gauge wire is
recommended. Using speaker wire larger than 14 gauge for
the SVL-4AB connections is not recommended —the wire
5
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
may not fit into the connectors. Never use solid-core, alu-
minum, or "Romex" type wire with the SVL-4AB. When run-
ning speaker wires inside walls, most states and municipalities
in the U.S. specify that you must use a special type of speaker
wire. Usually, the requirement is that the wire has a specific
"CL" fire rating, such as "CL-2" or "CL-3". Consult your Niles
dealer, building contractor, or local building and inspection
department if unsure about which type of wire is best for
your application.
Avoiding Interference
Speaker wires can act as an antenna for electrical noise.
Locating speaker wires too close to a light dimmer or switch
may cause a "buzzing" or "popping" sound to be heard
though the speakers. If you must locate the SVL-4AB wiring
near electrical devices, route the speaker wires several feet
away from the electrical wiring.
Using the SVL-4AB with Tube-Type Amplifiers
Virtually all tube amplifiers must have a load connected at all
times. If one of the amplifiers to be connected to the SVL-4AB
is a tube amplifier, be sure to always have at least one pair of
speakers switched on at all times. An alternative is to perma-
nently connect a 150 ohm, 5 watt resistor across the tube
amplifier's output in parallel with the SVL-4AB. See (Figure 1)
on next page for a hookup diagram.
6
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Tube Amplifier
Figure 1
Using a
Tube Amplifier
150Ω 5 Watt Resistor
150
150
Niles SVL-4AB
AMPLIFIER
L- R-
SPEAKER
4
SPEAKER
3
SPEAKER
2
SPEAKER
1
L+
R+
L+
L-
R-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
ON OFF
CONSTANT
PROTECTION
Niles Audio
Corporation,
Miami, Florida USA
7
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Recessed areas for
custom room
labels.
12 position volume control provides
greater attenuation than conven-
tional 10 position designs.
Attractive
low-profile
design.
SVL-4 AB SPEAKER SELECTION/ VOLUME CONTROL SYSTEM
A
B
OFF
ON
A
B
OFF
ON
A
B
OFF
ON
A
B
OFF
ON
PROTECTION
SPEAKER
1
SPEAKER
2
SPEAKER
3
SPEAKER
4
Each speaker pair is independently
activated with a simple pushbutton
On/Off switch.
Protection switch safeguards both
of your receivers or amplifiers
even with one amplifier playing all
4 pairs of speakers.
Each speaker pair can individu-
ally select one of two source
amplifiers with a dedicated
push-button A/B switch.
AMPLIFIER
A
AMPLIFIER
L- R-
B
SPEAKER
4
SPEAKER
3
SPEAKER
2
SPEAKER
1
L+
L
-
R
-
R+
L+
R+
L+
L
-
R
-
R+
L+
L-
R-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
CONSTANT
PROTECTION
ON OFF
ON OFF
NILES
Niles Audio Corporation, Inc.
Miami, Florida USA
A
B
Two-piece
removable
connectors.
Constant Impedance
Protection Switches for
each amplifier.
8
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion
1. Select a convenient location for the SVL-4AB.
2. Run all the necessary wiring to the SVL-4AB. Label the
wires for future reference. See (Figure 2).
Figure 2
Wiring Diagram
TUNER 94.9
15
Receiver A
AMPLIFIER
L- R-
SPEAKER
4
SPEAKER
3
SPEAKER
2
SPEAKER
1
L+
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
L+
L
-
R
-
R+
ON OFF
CONSTANT
PROTECTION
Niles Audio
Corporation,
Miami, Florida USA
Niles SVL-4AB
Speaker
Pair 4
Speaker
Pair 3
Speaker
Pair 2
Speaker
Pair 1
9
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
3. Make th e con n ection s to th e SVL-4AB. Th e
amplifier/speaker connectors on the SVL-4AB are removable.
If you wish, you may remove the SVL-4AB's connectors to
facilitate installation [see (Figure 3)]. Strip 3/8" of insulation
from the end of each wire. Tightly twist the end of each wire
until there are no frayed ends. Insert each wire into the
appropriate hole on the connector terminals. Be certain that
proper “phasing” is observed . To achieve proper phasing,
connect the positive terminals on the SVL-4AB to the positive
terminals on the amplifiers and speakers and the negative
terminals on the SVL-4AB to the negative terminals on the
amplifiers and speakers. If you are using only one amplifier it
should be connected to the “Amplifier A” connector and the
pushbutton switches marked “A/B” should be left out or in
the “A” position. If you will be using two amplifiers, connect
the second amplifier to the “Amplifier B” connector on the
SVL-4AB. Re-install the connectors if they were removed. See
(Figure 4).
Figure 3
Removing the
Connectors
4. Locate the pre-printed Room Labels. Affix the appropriate
label to the recessed area over each ON/OFF selector button.
Figure 4
Installing the Connectors
10
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Operat ion
The are two ways to use the SVL-4AB. You may play and
adjust the volume of one pair of speakers at a time, or play
multiple pairs simultaneously.
"TECH TIP"
If your amplifier or
receiver has "A"
and "B" speaker-
pair outputs,
connect the SVL-4AB
to the "A" outputs.
Do not connect
If you intend to play more than one pair of speakers at the
same time, you will need to become familiar with the opera-
tion of the SVL-4AB's PROTECTION button.
Playing One Pair of Speakers At a Time
anything to "B".
This will prevent
the amplifier or
1. Make sure the amplifier or receiver power is OFF and set
the volume to minimum.
2. Set the SVL-4AB volume control for the speaker pair you
wish to play to maximum (fully clockwise).
receiver from driving
an unusually low
impedance load.
3. Locate the ON/OFF button on the SVL-4AB which corre-
sponds to the speaker pair you wish to play. Set it to the ON
position.
4. Adjacent to the ON/OFF button is the amplifier A/B but-
ton. Choose an amplifier for the active speaker pair by press-
ing the A/B button in for “B” and out for “A”.
5. Turn on the amplifier or receiver and select a source, such
as the tuner or CD player.
6. Slowly turn up the amplifier or receiver volume and set it
to a comfortable (not maximum) listening level. Be careful
11
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
not to overdrive or "clip" your am plifier. If the sound
"TECH TIP"
becomes muddy or distorted, you have reached the limit of
your amplifier's volume capability and should quickly reduce
the volume to avoid damaging your speakers.
You will need to
activate the SVL-
4AB's PROTECTION
button whenever the
overall system
impedance might fall
below
7. Using the appropriate volume control on the front of the
SVL-4AB, adjust the volume of the speakers to the desired lis-
tening level.
8. You can turn off the speakers by turning the appropriate
volume control on the SVL-4AB fully counter-clockwise or by
pressing the ON/OFF button.
9. You can switch to the other amplifier by pressing the
amplifier A/B button.
Playing Two or More Speaker Pairs Simultaneously
1. Make sure both of the amplifiers are OFF and set the vol-
ume controls to minimum.
2. On the right side of the SVL-4AB's front panel is a button
labeled PROTECTION. This button activates the SVL-4AB's
impedance correction circuitry. The circuitry assures that both
of your receivers or amplifiers will see a safe operating load
when playing multiple speaker pairs simultaneously. Since
most receivers and amplifiers are not rated for use below a 4
ohm load, you will need to activate the PROTECTION button
whenever the overall system impedance might fall below 4
ohms. Use the following chart as a guide.
12
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
When playing the following speakers:
1 or 2 pair of 8-ohm speakers
The Protection button should be:
OFF
ON
OFF
ON
ON
3 or 4 pairs of 8-ohm speakers
1 pair of 4-ohm speakers
2, 3, or 4 pairs of 4-ohm speakers
Any combination of 4 and 8 ohm speakers
Set the PROTECTION button to the correct position using the chart shown above.
3. Set the SVL-4AB volume controls which correspond to the
speaker pairs you wish to play to maximum (fully clockwise).
"TECH TIP"
The volume control
of your amplifier or
receiver acts as the
master volume for all
of your speaker
pairs. Set this control
to a comfortable (not
maximum)) listening
level. Be careful not
to overdrive or “clip”
your amplifier. If you
hear distortion from
your speakers
4. Locate the appropriate ON/OFF buttons on the SVL-4AB.
Set them to the ON position.
5. Adjacent to the ON/OFF buttons are the amplifier A/B but-
tons. Choose an amplifier for each active speaker pair by
pressing the A/B button in for “B” and out for “A”.
6. Turn on the amplifiers or receivers and select a source,
such as the tuner or CD player.
7. Slowly turn up each of the amplifiers or receivers volume
and set it to a comfortable (not maximum) listening level. Be
careful not to overdrive or "clip" your amplifier. If the sound
becomes muddy or distorted, you have reached the limit of
your amplifier's volume capability and should quickly reduce
the volume to avoid damaging your speakers.
reduce the volume of
your amplifier to
avoid damaging your
speakers.
8. Using the appropriate volume controls on the front of the
SVL-4AB, adjust the volume of the speakers to the desired lis-
tening level. The volume control of your receiver or amplifier
acts as the master volume for all of your speaker pairs.
13
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
9. You can turn off the speakers by turning the correspond-
ing volume controls on the SVL-4AB fully counter-clockwise,
or by pressing the appropriate ON/OFF button. Refer to the
Protection Chart located on page 13 for the correct setting of
the PROTECTION button.
SPECIFICATIONS
Audio Power
Handling
100 watts/channel
continuous music
power
10. At any time, you may choose to switch any of the active
speaker pairs to one or the other of the amplifiers by pressing
the corresponding amplifier A/B button.
Frequency Response
+/- 1.2 dB from 20 Hz
to 20 kHz
Constant Protection Switches
Mounting
Table-Top component
The SVL-4AB is equipped with rear panel overrides of the
protection circuits that enables you to maintain constant
impedance protection regardless of the position of the front
panel switch. This will safeguard either or both of your ampli-
fiers from being overdriven due to accidental or improper
use by anyone unfamiliar with the equipment.
Wiring Requirements
Individual runs of
2-conductor speaker
wire. Connectors
accommodate wire
sizes 14-22 gauge (16
gauge recommended)
To engage one or both of these overrides, move the rear
panel "CONSTANT PROTECTION" switches to the "ON" posi-
tion. Constant impedance protection will be maintained until
the switches are turned to "OFF".
Overall Dimensions
17" (432mm) wide x
2" (51mm) high x
9 1/4" (235mm) deep
Weight
7 1/2 lbs. (3.4 kg).
14
Niles Audio
Corporation
12331 S.W. 130 Street
Miami, Florida, 33186
Tel: (305) 238-4373
Fax: (305) 238-0185
© 1999 Niles Audio Corporation All rights reserved. Because Niles believes in constantly improving its
products, Niles reserves the right to change product specifications without notice. Niles and the Niles
logo are registered trademarks of Niles Audio Corporation. Printed in USA 1/99 DS00127A
|