Nady Systems Microphone XR 61 User Manual

Nady wireless systems are type accepted under FCC rules

parts 90, 74, and 15.

This device complies with RSS-210 of Industry & Science

Canada.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference and (2) this device

must accept any interference received, including interference

that may cause undesired operation.

NADY XR-61

VHF DigiTRU Diversity™ System

XR PRO SERIES

WIRELESS MICROPHONE SYSTEM

OWNER’S MANUAL

NADY SYSTEMS, INC. • 6701 SHELLMOUND STREET, EMERYVILLE, CA 94608

Tel: 510.652.2411 • Fax: 510.652.5075 • www.nadywireless.com

INTRODUCTION

XR-61 RECEIVER

Reception Mode

Controls

DigiTRU Diversity™

Power ON/OFF, volume control, mute control

Thank you for purchasing a Nady XR Pro Series XR-61 Diversity Wireless Microphone

System and congratulations on your choice. Also available is the XR-62, which is a single

rackmount unit with dual receivers for operation of 2 channels simultaneously. The XR Pro

Series systems are loaded with top professional operating features and are the best per-

formance and price values available in VHF diversity rackmount wireless systems.

Connectors

Balanced XLR and unbalanced adjustable

1/4" audio out jacks, 2.1 mm barrel-type DC

input jack

LED Indicators

Diversity Dimensions (Max.)

Weight

Power ON, 5-LED RF & AF level displays, A/B

1.75" x 7.5" x 16.5" (4.4 x 19 x 42 cm)

3.82 lbs (1.73 kg)

Power Requirements

12V @ 400mA, nominal, AC/DC adapter

supplied

Antenna

Antenna Connectors

11.2" (28.5 cm), dual telescopic

dual SO-239 jacks

USING THIS MANUAL

This booklet gives instructions for the operation of the XR-61 single channel VHF wireless,

including handheld, instrument, lavalier, headmic and plug-in transmitter systems. Please

read the instructions for your system completely before operating unit.

This manual will first list the features of the XR-61 Pro Series System and then will take you

step by step in explaining how to operate your new system. After reading the receiver

instructions, turn to the section of the booklet that covers the type of transmitter used with

your new system. Each section will give you detailed operating instructions. Also included in

this manual are system specifications and servicing information.

SERVICE

(U.S.) Should your Nady XR-61 Pro Series Wireless Microphone System require service,

please contact the Nady Service Department via telephone at (510) 652-2411 or e-mail to

[email protected] for a Return Authorization (R/A) Number and a service quote (if

out of warranty). Make sure the R/A Number is clearly marked on the outside of the pack-

age and enclose a cashier's check or money order (if not prepaid with a credit card). Ship

the unit prepaid to: Nady Systems, Inc., Service Department, 6701 Shellmound Street,

Emeryville, CA 94608. Include a brief description of the problems you are experiencing.

The warranty card enclosed with this system contains additional valuable warranty and

service information. Keep it in a safe place for future possible reference. Do not attempt

to service this unit yourself as it will void the warranty.

(International) For service, please contact the Nady distributor in your country through the

dealer from whom you purchased this product.

SYSTEM FEATURES

SPECIFICATIONS

•

Available on selected frequencies in the VHF high band

(171-216 MHz) for interference-free, long-range performance

Proprietary companding circuitry for an industry-best 120dB

Dynamic Range, and the clearest, most natural sound available

Operating Range: Up to 250 feet typical (depending on site conditions)-up

to 500+ feet line-of-sight

XR PRO SERIES OVERALL SYSTEM PERFORMANCE

Frequency Response

25-20,000 Hz, +/-3dB

Dynamic Range

120dB

Total Harmonic Distortion

RF Carrier Frequency Range

Frequency Stability

Modulation

<0.3%

169-216 MHz

+/- 0.005%, crystal controlled

FM (F3E), +/-20KHz max.

Up to 250 ft. typical (depending on site

conditions); up to 500+ feet optimum line-of-sight

Noise-free transmitter ON-OFF operation

Operating Range

XR-61 RECEIVER

•

Rugged single rack space metal housing

Dual antennas and Nady’s advanced DigiTRU Diversity(tm) digital processing

circuitry for maximum dropout protection and operating range

RF and AF 5-LED displays for monitoring incoming signal strength and audio level

Convenient, front mounted recessed antenna jacks for either onboard or remote

antennas

Balanced microphone level XLR output and 1/4” adjustable line level output for

maximum versatility

Easy access volume control for adjustable audio output

Mute (squelch) adjust control

Externally powered by AC/DC power adaptor

TRANSMITTERS

Audio Inputs

•

• WHT-15

• WLT-15/WGT-15

Nady DM-10D neodymium dynamic cartridge

3.5mm mono locking jack for connecting to omni

or unidirectional lavalier mic or unidirectional

headworn mic, with phantom power (WLT-15);

or connecting to instrument cable (WGT-15)

Locking XLR jack for connecting to microphone or

cable, with selectable phantom power

•

• LINK 2™

Controls

• WHT-15

WHT-15 HANDHELD MIC TRANSMITTER

OFF/STANDBY/ON switch

OFF/STANDBY/ON switch, input level adjust

OFF/STANDBY/ON, LO/HI Level, and ON/OFF

Phantom power switch

Unit "ON" (single flash), Low Battery Alert

(steady)

50mW (Max. allowed by FCC)

>-40dB

9V Alkaline

•

Features the Nady DM -10D unidirectional neodymium dynamic cartridge

for optimum true sound, maximum feedback rejection and minimal handling noise

OFF/STANDBY/ON switch allows convenient audio muting with the

transmitter “ON”

Low battery LED indicator flashes once for unit “ON”; lights steady for low

battery alert

• WLT-15/WGT-15

• LINK 2™

LED Indicator

RF Power Out

Harmonic & Spurious Emissions

Battery

Rubber, “easy-mount” mic clip included

WGT-15 & WLT-15 BODYPACK TRANSMITTERS

•

Choice of instrument (WGT-15) or headworn/lavalier microphone (WLT-15)

bodypack transmitter

OFF/STANDBY/ON switch allows convenient audio muting with the

transmitter “ON”

Low battery LED indicator flashes once for unit “ON”; lights steady for low

battery alert

Locking 3.5mm mini-jack provides secure connection for removable microphone

or instrument cable

Battery Life

Dimensions

• WHT-15

• WLT-15/WGT-15

• LINK 2™

Weight (w/o battery)

• WHT-15

• WLT-15/WGT-15

• LINK 2™

Up to 15 hours

9.5" X 1.4" Diam. (24.1 X 3.5 cm)

4.1" X 2.4"X 0.8" (10.4 X 6.1 X 2.0 cm)

4.5" X 1.5" X 1.25" (11.4 X 3.8 X 3.2 cm)

6.9 oz (193 g)

3.6 oz (101 g)

2.6 oz (71 g)

Easily accessible input level adjust control for optimum sound

LINK 2™ PLUG-IN TRANSMITTER

•

Plug-in transmitter converts your favorite XLR handheld or lavalier microphone

to wireless instantly

•

Rugged construction and positive locking connector for reliable performance

Selectable phantom power and LO/HI audio input level

Optional leatherette pouch with clip available for use as bodypack

OPERATION

XR-61 RECEIVER

1. Rackmounting the Receiver

The XR-61 receiver is supplied with RACK EARS (1) which can be attached with the screws

provided on the front of the side panels to enable rackmounting the receiver. (Note: Do not

mount the receiver in a rack directly above an amplifier or other source of high heat-this

could degrade the performance of the XR-61/62. Always ensure adequate airflow and

heat dissipation in any rack configuration.)

2. Powering the Receiver

Plug the 12V AC/DC ADAPTER (2) provided into the DC INPUT JACK (3) on the back of the

receiver. Then plug the power supply into an AC outlet. (Note: Any 12V DC source with

400mA capability can also be used.) Press the POWER SWITCH (4) once to turn on the

receiver. The POWER ON LED (5) integrated into the switch will now light and the receiver

is operational.

3. Antennas

Connect the front panel TELESCOPIC ANTENNAS (5) or optional remote antennas to the

ANTENNA JACKS (6). Extend the antennas fully to obtain maximum range. Optimal

antenna position is 45 degrees from the receiver (at 90 degrees from each other). For max-

imum range, it is always best to maintain a line of sight (no obstructions) between the

receiver antennas and the transmitter at all times whenever possible

4. Mute (Squelch) Adjustment

In normal operation, the MUTE CONTROL (7) should be set fully counterclockwise to the

factory preset minimum RF level. However, in areas of high RF activity, the mute (or

squelch, as it is sometimes called) may need to be adjusted to compensate for the adverse

conditions in a particular location. If, with the transmitter off, the receiver’s A and/or B

DIVERSITY LED INDICATORS (8) and/or one or more LEDs of the 5 LED RF LEVEL DISPLAY

(9) flicker or stay on, the squelch control should be turned clockwise until the LEDs extin-

guish. When the squelch is properly adjusted, the A and/or B LEDs or the RF LEVEL LED

displays will only light when the system transmitter is turned on. Turning the squelch control

too far clockwise will reduce the range, but yield a quieter mute (squelch) function. During

operation, especially at ranges greater than 75 feet, one or the other of the A or B LEDs

may extinguish briefly. This is normal-the unit’s DigiTRU Diversity™ reception ensures that

the received audio will not be interrupted. When both the A/B DIVERSITY LEDs and the 5

LED RF LEVEL display extinguish, the transmitter is out of range for that given location, and

the user should move closer to the receiver to re-establish the radio link.

XLR Connector – Connects microphone to the transmitter module for signal input

Locking Ring – Locks microphone to the transmitter

Optional Pouch – For lavalier bodypack operation (with beltclip and strap ring for

securing)

Gain Control Switch – Adjusts the input sensitivity (LO or HI)

40 Low Battery LED – Single flash (power on), lit steady (low battery)

Power Switch - Turns the power ON/STANDBY/OFF. In standby position, the power is

on and the audio is off.

Phantom Power ON/OFF Switch – Turns the phantom power ON/OFF

Battery Compartment

Release Button – Press to release XLR connector

9V Alkaline Battery

4. Microphone Operation

5. Connecting the Audio Output

a. Turn on The Link 2 by sliding the ON/STANDBY/OFF SWITCH (41) to the STANDBY

position (transmitter on, audio muted) or the ON position (transmitter and audio both on).

The LOW BATTERY INDICATOR LED (40) will give a single quick flash, indicating usable

battery strength. In case of dead or low battery, the indicator will either not go on at all or

stay on continuously, indicating a battery voltage below 7V. If this occurs, replace with

fresh 9V battery. Remember to turn the transmitter off when not in use.

The XR-61 receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (10)

and an adjustable line level UNBALANCED AUDIO OUTPUT 1/4” JACK (11). The level

from the UNBALANCED OUTPUT is controlled by the rear panel VOLUME CONTROL (12).

(Note: As when making any connection, make sure the amplifier or mixing board volume is

at the minimum level before plugging in the receiver to avoid possible sound system dam-

age. Also make sure that the phantom power on the input of the mixer is turned OFF

before making connection to the receiver.)

b. The Link 2 is now ready to use. The A and/or B DIVERSITY LED INDICATORS (8) and

most or all of the RF DISPLAY LEDs (9) on the XR-61 receiver should now be lit, indicating

a received signal from the transmitter. When ready to speak, slide the transmitter switch to

the ON position and adjust the volume of the receiver as per the Audio Output

Microphone Connection section of the above XR-61 receiver instructions. The AF LEVEL LED

DISPLAY (13) on the XR-61 receiver will light up to 5 LEDs (4 green and 1 red) for all

input signals. Occasional flickering on and off during use of the top red LED

indicator in this display is normal, however if the red LED stays on continuously, it means

the signal is too loud and there is the possibility of overload distortion. Re-position the

microphone farther from the source or adjust the Link 2 transmitter gain with the VOLUME

LO/HI GAIN SWITCH (39). Set for the maximum possible level without noticeable distortion

on the high level peaks. Set the GAIN SWITCH to LO to decrease the audio level, and set

the GAIN SWITCH to HI to increase the audio level. The red LED indicator should flicker

only on the loudest inputs.

a. Instrument Connection (using the WGT-15 instrument transmitter)

Insert an audio cord with a 1/4” mono phone plug in the UNBALANCED OUTPUT

JACK (11) on the rear panel of the receiver. Plug the other end of the cord into an

amplifier, effects, or mixing board. Adjust the VOLUME CONTROL (12) on the XR-61

receiver clockwise to about 3/4 rotation, until the volume level is comfortable for your

application. This setting is roughly equivalent to a direct instrument cord connection.

Turning the volume up to maximum will provide 4dB gain over a cord.

b. Microphone Connection (using the WLT-15 transmitter with either a headset or

lavalier microphone or the WHT-15 handheld microphone transmitter)

For microphone use, either the BALANCED MIC AUDIO OUTPUT XLR (10) or the 1/4”

line level UNBALANCED OUTPUT (11) can be used. The XLR output is set at a non-

adjustable microphone level, similar to hardwired mic levels. Plug an XLR

connector into the XLR output jack on the rear of the unit and plug the other end

into your amplifier or mixing board. (Note: Make sure the phantom power on your

mixing board is turned off and the volume is turned down when making connections.)

For your convenience, the XLR output level is preset at the factory and is not adjustable

with the receiver volume control. To use the 1/4” UNBALANCED OUTPUT JACK (11),

follow the instructions for the Instrument Connection (above), except start with the

receiver volume at 1/2 MAX and adjust the volume control until the volume level is

optimal. If the volume control is set too high, you may overload your mixer or amp.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement

so that acoustic feedback (howling and screeching) will be avoided. Please also observe

the pickup patterns of the microphone selected: omnidirectional mics pick up sound equally

from all directions and are prone to feedback if not used carefully. Unidirectional mics are

more resistant to feedback, but pick up sound sources best that are directly in front of the

mic. Also, mics that are farther from the sound source, such as lavaliers, require more

acoustic gain and thus are also more prone to feedback than close-source mics such as

handheld or headworn mics that are used close to the mouth.]

(Note: Microphone elements can easily be destroyed by the buildup of salts and minerals

from perspiration and saliva. It is good practice to put a windscreen on the mic element at

all times to protect it.)

THE LINK 2™ PLUG-IN TRANSMITTER

1. Transmitter Set-Up

First, slide open the BATTERY COMPARTMENT DOOR (43) to expose compartment. Insert a

fresh 9V ALKALINE BATTERY (45), observing polarity. Close the battery compartment door.

2. Handheld Microphone Installatio

• Step 1 - Rotate the transmitter’s threaded LOCKING RING (37) clockwise toward the

XLR CONNECTOR (36) until it stops.

• Step 2 - Hold your mic in one hand and The Link 2 in the other.

• Step 3 - Plug your mic into the XLR CONNECTOR.

XR-61 Receiver

• Step 4 - Lock the mic into place with the adjustable threaded LOCKING RING by

rotating the ring, counterclockwise, to the top of the transmitter.

• Step 5 - To release the XLR CONNECTOR, turn the threaded LOCKING RING clock

wise and press the RELEASE BUTTON (44).

3. Lavalier Microphone Installation

The lavalier microphone you are using must terminate with an XLR connector and conform

to the pin assignments shown below. If they do not conform, you must use an appropriate

adapter or the lav mic may not work with the Link 2. If you have any questions, please con-

tact your Nady dealer or Nady Systems’ Customer Service Department.

Note: the pin assignments on The Link 2’s XLR connector are as shown:

Note: Select phantom power, as needed, with the PHANTOM POWER ON/OFF SWITCH (42)

WHT-15 HANDHELD MICROPHONE TRANSMITTER

1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the BATTERY

HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the correct polarity as

marked, and screw the cover back on to the microphone. Make sure the cover is screwed

on completely. A fresh alkaline battery can last up to 16 hours in use, but in order to

ensure optimum performance, it is recommended that you replace the battery after every

10 hours of use.

2. Turn on the WHT-15 by sliding the OFF/STANDBY/ON SWITCH (20) to the STANDBY

position (transmitter on, audio muted) or the ON position (transmitter and audio both on).

The BATTERY INDICATOR LED (21) will give a single quick flash, indicating usable battery

strength. In the case of a dead or low battery, the LED will either not go on at all or will

stay on continuously, indicating that the battery should be replaced with a fresh one. To

preserve battery life, turn the transmitter off when not in use.

3. The microphone is now ready to use. The A and/or B DIVERSITY LED INDICATORS (8)

and most or all of the RF LEVEL DISPLAY LEDs (9) on the XR-61 receiver should now be lit,

indicating a received signal from the transmitter. When ready to speak, slide the transmitter

switch to the ON position. Adjust the volume of the receiver as per the Audio Output

Microphone Connection section of the above XR-61 receiver instructions. The AF LEVEL

LED DISPLAY (13) on the XR-61 receiver will light up to 5 LEDs (4 green and 1 red) for all

input signals. Occasional flickering on and off during use of the top red LED indicator in

this display is normal, however if the red LED stays on continuously, it means the signal is

too loud and there is the possibility of overload distortion. Back off from the microphone

until the red LED indicator only flickers on peaks.

[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement

so that acoustic feedback (howling or screeching) will be avoided.]

[Note: Microphone elements can easily be destroyed by the buildup of salts and minerals

from perspiration and saliva. It is good practice to put a windscreen on the mic element at

all times to protect it.]

WGT-15 INSTRUMENT BODYPACK TRANSMITTER

1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31),

observing the correct polarity. Close the compartment. The WGT-15 is provided with a

3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To secure the

connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To

unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes or

instrument strap. (Note: As the cord to the instrument also serves as the antenna, be sure to

extend it fully for maximum range. Rolling up or shortening the cord may reduce the effec-

tive operating range.)

2. Turn on the WGT-15 by sliding the OFF/STANDBY/ON SWITCH (32) to the STANDBY

position (transmitter on, audio muted) or the ON position (transmitter and audio both on).

The BATTERY INDICATOR LED (33) will give a single quick flash, indicating usable battery

strength. In the case of a dead or low battery, the LED either will not go on at all or will

stay on continuously, indicating that the battery should be replaced with a fresh one.

3. The WGT-15 transmitter is now ready to use. The A and/or B DIVERSITY LED INDICA-

TORS (8) and most or all of the RF DISPLAY LEDs (9) on the XR-61 receiver should now be

lit, indicating a received signal from the transmitter. Adjust the volume of the receiver as per

the Audio Output Instrument Connections section of the above XR-61 receiver instructions.

For optimum performance, an INPUT LEVEL CONTROL (34) is provided on the top panel of

the WGT-15. Adjust the gain by turning the control with a small slot head screwdriver. It is

recommended that this control be turned to maximum gain. However, for ultra high-gain

instrument sources such as active bass pickups or even extra hot guitar pickups, turning the

level down slightly will create a cleaner sound.

(Note: Turning down the input gain too much can compromise the signal-to-noise ratio and

is not recommended. Set for the maximum possible gain and headroom without noticeable

distortion on the high level peaks).

The AF LEVEL LED DISPLAY (13) on the XR-61 receiver will light up to 5 LEDs (4 green and

1 red) for all input signals. Occasional flickering on and off during use of the top red LED

indicator in this display is normal, however if the red LED stays on continuously, turn down

the instrument volume or adjust the INPUT LEVEL CONTROL (34) on the WGT-15 transmit-

ter, or noticeable distortion may result.

(Note: Scratchy noises can sometimes occur when some electric guitars/basses with dirty

pots or connections are used with any wireless system. For this reason, the supplied

INSTRUMENT CORD (35) has a factory installed capacitor inside the 1/4” plug. This

capacitor provides first order filtering of the RF signal from the cord into the guitar and

eliminates virtually all scratchy noises. Should your equipment still give you scratchy noises,

we suggest these steps to eliminate them:

1) Make sure all guitar volume and tone pots are clean and all contacts are

solid-this is very important.

2) Provide extra filtering with a 220 pF capacitor soldered across the hot to ground

terminals of the guitar’s volume and tone pots.)

WLT-15 LAVALIER/LAPEL OR HEADWORN MICROPHONE BODYPACK TRANSMITTER

1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23),

observing the correct polarity. Close the compartment.

2. The WLT-15 is provided with a 3.5 mm LOCKING JACK (24) for connecting the micro-

phone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN MICROPHONE (26), as

supplied. To secure the connection, turn the metal slip ring on the plug clockwise to thread

it on to the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip

on to your clothes. To use the lavalier mic, attach it at chest level. Do not place too close

to the mouth-a distance of about six inches usually works best. To use the headworn mic,

place it on the head and adjust the mic boom so that the mic is about one inch to the side

of the front of the mouth. (Note: The lavalier or headworn mic wire is also the transmit

antenna, and rolling up or shortening the wire may reduce the effective operating range.

Extend the wire fully during use, and keep it as straight as possible.)

3. Turn on the WLT-15 by sliding the OFF/STANDBY/ON SWITCH (27) to the STANDBY

position (transmitter on, audio muted) or the ON position (transmitter and audio both on).

The BATTERY INDICATOR LED (28) will give a single quick flash, indicating usable battery

strength. In the case of a dead or low battery, the LED either will not go on at all or will

stay on continuously, indicating that the battery should be replaced with a fresh one.

4. The microphone is now ready to use. The A and/or B DIVERSITY LED INDICATORS (8)

and most or all of the RF DISPLAY LEDs (9) on the XR-61 receiver should now be lit, indicat-

ing a received signal from the transmitter. When ready to speak, slide the transmitter switch

to the ON position and adjust the volume of the receiver as per the Audio Output

Microphone Connection section of the above XR-61 receiver instructions. The AF LEVEL

LED DISPLAY (13) on the XR-61 receiver will light up to 5 LEDs (4 green and 1 red) for all

input signals. Occasional flickering on and off during use of the top red LED indicator in

this display is normal, however if the red LED stays on continuously, it means the signal is

too loud and there is the possibility of overload distortion. Re-position the microphone far-

ther from the source or adjust the AUDIO INPUT LEVEL CONTROL (29) until the red LED

indicator flickers only on the loudest inputs.