NETGEAR Switch NAS 1100 User Manual

J. Mounting ear for 2-  
3. Install the hard disks into the trays.  
post rack mounting  
)NSTALLATION 'UIDE  
K. Disk tray door access  
NETGEAR ReadyNAS 1100  
L. Disk tray with lock-on  
latch  
Start here  
M. Thumb-screw latch  
(system module access)  
Follow these instructions to install your NETGEAR® ReadyNAS™ 1100. Then, consult  
the ReadyNAS Setup Manual on your Installation CD for instructions on installing the  
RAIDar utility and using the FrontView Setup Wizard to configure the ReadyNAS.  
Access the ReadyNAS User Guide on the Installation CD to configure any advanced  
features. The ReadyNAS User Guide is also on the NETGEAR support site at  
N. Cooling fans  
O. Power switch  
P. Power connection  
(100~240VAC,  
50/60 Hz)  
4. With the latch in the open position, slide the disk trays into the unit completely,  
securing the latch and closing the door.  
Q. Label (includes serial number and MAC address)  
Warning: If you purchased a diskless unit, please read the optional disk installation  
section before installing the RAIDar™ utility or connecting ReadyNAS to the network.  
R. Ethernet ports (2)  
First, check your package contents  
Install the hard disks (optional)  
Finally, install the RAIDar utility  
Before starting installation, check your package contents:  
This is an optional step, required only if you purchased a diskless unit.  
Your Installation CD contains the RAIDar utility for Windows, MAC and Linux. See the  
ReadyNAS Setup Manual for installation instructions. When you complete installation of  
the RAIDar utility, you are ready to connect ReadyNAS to your network and then power  
on ReadyNAS.  
ReadyNAS 1100  
1. Remove disk trays from the unit:  
a. Open the door.  
Four hard disk trays (not included with diskless units)  
Installation Guide  
b. Press to release the latch.  
c. Pull out the tray.  
Warranty Card  
Power cable  
Connect ReadyNAS  
Ethernet cable  
2. Set the lock before installing the hard  
ReadyNAS Installation CD  
disk into the tray (optional).  
When connecting ReadyNAS, please note the following:  
16 screws for hard disk installation (included only with diskless units)  
ReadyNAS connected directly to your network: If your client has a static IP  
address, make sure it is on the same IP address subnet as the ReadyNAS device. You  
can do this by configuring your client to obtain its IP address via DHCP. Even if your  
network does not have existing DHCP service, the ReadyNAS device will assure that  
you will get an IP address.  
Then, take a moment to identify the features of your  
ReadyNAS 1100  
A. Programmable backup button  
F. Ethernet activity LEDs (2)  
ReadyNAS connected directly to your PC: If you are connecting a PC directly to  
ReadyNAS (and not through a network), first set a static IP address on your PC in the  
192.168.168.xxx subnet, subnet mask 255.255.255.0. You can then use RAIDar to  
detect ReadyNAS, or you can open a browser and enter the ReadyNAS default IP  
address https://192.168.168.168/admin to connect to the ReadyNAS.  
B. USB ports (3)  
G. Power LED  
C. USB activity light (1)  
H. System reset button  
D. Disk LEDs (4). Green for disk online.  
E. Activity LED. Blinks for disk access.  
I. Power Button (To power off, depress  
for 5 seconds or until LED blinks.)  
 

NETGEAR Network Router WAG102NA User Manual
Nilfisk ALTO Ventilation Hood MX 521 H User Manual
Oceanic Personal Computer Veo 100Nx User Manual
Olympus Microcassette Recorder digital voice recorder User Manual
Onkyo Stereo Amplifier RDA 71 User Manual
Onkyo Stereo Receiver HT RC470 User Manual
Outback Power Systems Automobile Battery Charger FX 2012T User Manual
Panasonic All in One Printer DP 1510P User Manual
Panasonic Network Card 2SC1318 User Manual
Panasonic Ventilation Hood FV 08VKML2 User Manual