NETGEAR Switch GC102 User Manual

®
© 2002 by NETGEAR, Inc. All rights reserved.  
LEDs  
START HERE  
This table describes the activity of the Model GC102 Converter LEDs.  
Trademarks  
Congratulations on your purchase of the NETGEAR® Model GC102 Gigabit Ethernet Media Converter -a  
cost-effective, high-performance network solution designed to enable flexible network design at gigabit  
speeds.  
©2002 NETGEAR, Inc. NETGEAR® , the Netgear Logo, the Gear Guy, and Everybody's connecting are  
trademarks or registered trademark of Netgear, Inc. in the United States and/or other countries.  
Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Microsoft  
Corporation in the United States and/or other countries. Other brand and product names are trademarks  
or registered trademarks of their respective holders. Information is subject to change without notice. All  
rights reserved.  
Label  
Color  
Green  
Activity  
Description  
This installation guide describes how to install and use the Model GC102 Gigabit Ethernet Media  
Converter .  
PWR(Power)  
On  
Power is supplied to the Converter.  
Power is disconnected.  
Off  
LNK (Link)  
Green  
Green  
On  
A valid link is established on the port.  
A link is not established on the port.  
Statement of Conditions  
FEATURES  
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves  
the right to make changes to the products described in this document without notice.  
(located to the  
right of each port)  
Off  
The Model GC102 Gigabit Converter has the following features:  
One RJ-45 connector port, using Category 5 or better cable to deliver 1000BASE-T up to 100m (328 ft)  
NETGEAR does not assume any liability that may occur due to the use or application of the product(s)  
or circuit layout(s) described herein.  
ACT (Activity)  
On  
Packet transmission or reception is  
occuring on the port.  
Certificate of the Manufacturer/Importer  
One SC connector port, using 62.5/125 micron multimode fiber cable to deliver 1000BASE-SX up to  
550m (1,804 ft)  
It is hereby certified that the NETGEAR Model GC102 Converter has been suppressed in accordance  
with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some  
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject  
to certain restrictions. Please refer to the notes in the operating instructions. Federal Office  
(located to the  
right of each port)  
Off  
No traffic is passing through the port  
Auto Uplink on the RJ-45 port to adjust for straight through or cross-over cables  
Easy plug-and-play installation with no software to configure, which saves time and minimizes the poten-  
tial for configuration errors.  
for Telecommunications Approvals has been notified of the placing of this equipment on the market and  
has been granted the right to test the series for compliance with the regulations.  
Rear Panel  
The rear panel of the Model GC102 Converter has a power adapter receptacle for the supplied power  
adapter, as well as a switch to select flow control for the fiber port. If the switch is in the 'ON' position, the  
GC102 will auto negotiate flow control on the SC connector. If the switch is in the 'OFF' position, the con-  
verter will not use flow control or respond to any negotiation message.  
Voluntary Control Council for Interference (VCCI) Statement  
LEDs that provide network traffic and port status  
This equipment is in the first category (information equipment to be used in commercial and/or industrial  
areas) and conforms to the standards set by the Voluntary Control Council for Interference by Data  
Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in  
commercial and/or industrial areas.  
IEEE 802.3x Flow Control standard compliance  
Selector for Auto negotiation of flow control on the 1000BASE-SX port  
Compact, sturdy metal case design that enables easy desktop, all-mount, or under-desk installaiton  
Note: The converter will determine the switch setting when powering up. Once the converter is  
operational, it ignores the switch position. If you want to change the setting, you must reset the  
converter.  
Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio  
interference may be caused to equipment such as radios and TV receivers.  
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice  
PACKAGE CONTENTS  
Note: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not  
installed and used in accordance with the instruction manual, it may cause harmful interference  
to radio communications. Operation of this equipment in a residential area is likely to cause  
harmful interference, in which case users will be required to take whatever measures may be  
necessary to correct the interference at their own expense.  
Wall mounr  
installation kit  
adapter  
EN 55 022 Statement  
Installation guide,  
Warranty & Owner  
Registration Card,  
and Support  
This is to certify that the NETGEAR Model GC102 Converter is shielded against the generation of radio  
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity  
is declared by the application of EN 55 022 Class A (CISPR 22).  
Information Card  
Verify that your package contains the following:  
Model GC102 Gigabit Ethernet Media Converter  
Wall Mounting kit  
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case  
the user may be required to take appropriate measures.  
APPLICATIONS  
The Model GC102 Gigabit Ethernet Converter is designed to provide flexibility for your network design.  
Converters can be used as a stand-alone device or can be used in a back-to-back configuration. The exam-  
ples in this section illustrate some common network environments, using other NETGEAR products. These  
examples focus on the benefit of the converter and do not show the workstations, servers, printers, and  
routers that you would expect to find on a network.  
This installation guide  
Canadian Department of Communications Radio Interference Regulations  
®
Warranty & Owner Registration Card  
Support Information Card  
The digital apparatus (NETGEAR Model GC102 Converter does not exceed the Class A limits for radio-  
noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian  
Department of Communications.  
Power adapter  
Although the examples illustrate specific NETGEAR switches, any switches can be used in the network con-  
figurations shown.  
Note: Do not remove the dust cover from the fiber port until you are ready to connect the fiber optic  
Réglement sur le brouillage radioélectrique du ministère des Communications  
cable. Dust contamination can degrade the performance of the port and the media converter.  
Cet appareil numérique (NETGEAR Modle GC102 Converter respecte les limites de bruits radioélec-  
triques visant les appareils numériques de classe A prescrites dans les Réglementations sur le brouillage  
radioélectrique du Ministère des Communications du Canada.  
NETGEAR, Inc.  
Stand alone configuration  
4500 Great America Parkway  
Santa Clara, CA 95054  
USA  
The GC102 can be used in to convert a fiber connection from a distant wiring closet to the desired copper  
gigabit connection that is needed. In this example, a GS524T is able to support a distant FS750 with an  
AG711F Fiber Gigabit module in it by using the GC102.  
PRODUCT ILLUSTRATION  
Copper Gigabit Ethetnet Port  
Support: 1-888-NETGEAR  
E-mail: support@NETGEAR.com  
The RJ-45 port provides 1000BASE-T connectivity over Category 5 (Cat5) or better (Cat5e, Cat6)  
unshielded twisted pair (UTP) cables for a distance up to 100 m (328 ft).  
With Auto Uplink technology, the GC102 automatically adjusts for either straight-through or crossover  
cables to make the right link.  
Fiber Gigabit Ethernet Port  
The SC port provides 1000BASE-SX connectivity over 62.5/125 micron multimode fiber cable for a dis-  
tance up to 550m (1,804 ft). Be sure to match up the transmit and receive portions on the converter to  
the correct parts of the plug.  
M-GC102NA-0  
M 1- G C 1 0 2 N A - 0  
 

Miele Double Oven H 4844 BP User Manual
Minolta Digital Camera x370 User Manual
Napoleon Fireplaces Outdoor Fireplace B36DFN User Manual
NEC Projector M271W User Manual
NETGEAR Network Router WNDR3700v2 User Manual
NETGEAR Printer FWG114P v2 User Manual
Newcon Optik Microscope Magnifier YUNNAT 2P 3 User Manual
NordicTrack Treadmill NTL189070 User Manual
Oregon MP3 Player MP 130 User Manual
Oster Music Mixer 6625 User Manual