NETGEAR Server RNDP6350 100NAS User Manual

6. On the Admin Password page,  
change the system login  
password, and provide a  
recovery question, answer, and  
email address. Note these  
changes. Click Next to  
proceed.  
Use the Setup Wizard to Configure Basic Settings  
)NSTALLATION 'UIDE  
The Setup Wizard will guide you through setting up basic file sharing. Refer to the  
ReadyNAS Pro User Manual for instructions on configuring options like backup,  
streaming media servers, printers, VLAN, or user accounts and quotas.  
NETGEAR® ReadyNAS™ Pro  
Note: If you choose to bypass the Setup Wizard, be sure to configure and alerts email  
address, change the admin password, and provide a password recovery question.  
Follow these instructions to install your NETGEAR® ReadyNAS™ Pro. Then, consult  
the ReadyNAS Pro User Manual for instructions on configuring and operating your unit.  
A link to the ReadyNAS Pro User Manual is on the Installation CD and on the NETGEAR  
support site at http://kbserver.netgear.com. These instructions assume the unit is using the  
factory default X-RAID2 disk configuration.  
7. On the Security Mode tab  
1. In the factory default state,  
when logged in to the unit,  
Setup Wizard is enabled. Click  
Next to proceed with the  
wizard.  
page, accept the default option  
of “User” which controls  
access to shares based on user  
or group accounts. FrontView  
will attempt to use the first workgroup name it discovers in the network. Otherwise, it  
will default to “VOLUME” as the workgroup name. Specify the workgroup name you  
want the unit to join. Refer to the ReadyNAS Pro User Manual for ACS setup  
instructions. Click Next to proceed.  
Estimated completion time: 20 minutes.  
Note: A diskless unit requires installing disks and initializing RAID before proceeding.  
Go to http://kbserver.netgear.com for a list of supported disks. Refer to the ReadyNAS Pro  
User Manual for instructions on installing disks and configuring RAID.  
2. On the Clock tab page, modify  
or accept the default timezone,  
time, and NTP options. Click  
Next to proceed.  
First, Install the RAIDar Utility  
8. On the Accounts page, click Add User. Add a new user and user password. Click  
Next to finish the wizard. Refer to the ReadyNAS Pro User Manual for full  
instructions on setting up accounts.  
3. On the Alerts tab page, provide  
at least one email address for  
system alerts. Click Next to  
proceed.  
Install the RAIDar utility from the product Installation CD. Windows, MAC and Linux  
versions of the RAIDar utility are provided.  
This completes the basic setup. Next, you will verify that you can access shares on your  
ReadyNAS Pro.  
Next, Connect the Unit  
4. On the Ethernet 1 tab page,  
accept or change the IP address  
settings.  
For initial setup, connect one Ethernet port of the ReadyNAS Pro to your network, and  
turn it on. It takes about a minute to boot. The factory default is to get its IP address via  
DHCP. After it boots, the status area will display the IP address assigned to the unit and  
the amount of disk space available. Note the IP address displayed in the status area.  
Accessing Your Shared Storage  
Click Next to proceed.  
Follow the steps below to access shares on the ReadyNAS Pro.  
5. On the Global Settings tab  
page, you can modify the unit’s  
hostname. Also, if you will use  
a static IP configuration, you  
will need to configure the  
Note that, by default, these file sharing protocols are enabled: CIFS, AFP (advertised over  
both Bonjour and ATP), HTTP/S. FTP, NFS, and Rsync are supported but are not enabled  
by default.  
Log in to the Unit  
Refer to the ReadyNAS Pro User Manual for instructions on accessing shares from Linux  
or Unix workstations, drive mapping, and other file sharing options, including unique  
language support for file names such as those that use unicode or ideographic characters.  
1. Run the RAIDar utility. It will detect the unit.  
gateway and DNS settings (you  
do not have to change these  
settings if you use the unit in its  
default DHCP configuration).  
Click Next to proceed.  
Tip: In your DHCP server, reserve the IP address assigned for your ReadyNAS Pro so that  
it always gets this address. This helps assure that mapped drives work consistently on  
any operating system.  
Accessing Shares from a Windows PC  
2. Click Setup to open a browser ReadyNAS Pro FrontView session  
with the unit. The login screen will display. The default user name  
is admin and the password is netgear1.  
1. To see a share listing in Windows, either click Browse in RAIDar or enter  
\\<ip_address> or \\<hostname> in the Windows Explorer address bar.  
\\Nv6-07-15-F4  
The FrontView configuration utility home page displays.  
 

MotoSAT Stereo System Antenna User Manual
NAD Universal Remote HTR 1 User Manual
Nielsen Kellerman GPS Receiver ClearNav User Manual
Nikon Network Card EH 6a User Manual
NordicTrack Home Gym NTHK99901 User Manual
Novatel Radio Antenna SMART V1 User Manual
Oliveri Plumbing Product 883U User Manual
Panasonic Car Video System CQ VD7005U User Manual
Panasonic Cordless Telephone KX TG3711BX User Manual
Panasonic VCR DS850 User Manual