CSM-200 Series
Hardware Installation Guide
First Edition, November 2009
© 2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City,
Taipei, Taiwan, R.O.C.
TEL: +886-2-8919-1230
P/N: 1802002002010
Features
y
LFP(Link Fault Pass-through) and FEF(Far End Fault)
y
Two different operation modes
¾
¾
Store-and-Forward
Pass Through
y
y
y
y
y
Auto negotiation
Support TS-1000 ver. 2
Support Turbo Ring 2
Plug and Play
Hot-swap
Package Checklist
Moxa’s CSM-200 Series is shipped with the following items. If any of these
items is missing or damaged, please contact your customer service
representative for assistance.
y
y
y
CSM-200 Series
Hardware Installation Guide
Warranty Card
NOTE: Please notify your sales representative if any of the above items are
missing or damaged.
Dimensions
CSM-200-1213
PWR
Fiber
Link
TX
RX
86.8 mm
10M
(3.42 in)
100M
117.1 mm (4.61 in)
124.3 mm (4.89 in)
21 mm
(0.83 in)
- 3 -
CSM-200-1214/CSM-200-1218
PWR
Fiber
Link
TX
RX
86.8 mm
(3.42 in)
10M
100M
117.1 mm (4.61 in)
124.3 mm (4.89 in)
21 mm
(0.83 in)
ATTENTION
Electrostatic Discharge Warning!
To protect the product from damage due to electrostatic
discharge, we recommend wearing a grounding device when
handling your CSM-200 slide-in modules.
Communication Connections
The CSM-200 Series has one 10/100BaseT(X) Ethernet port, and one
100BaseFX (SC or ST type connector) fiber port.
10/100BaseT(X) Ethernet Port Connection
The 10/100BaseT(X) Ethernet ports located on CSM-200 are used to connect
to Ethernet-enabled devices.
Below we show pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports, and also show cable wiring diagrams for
straight-through and cross-over Ethernet cables.
RJ45 (8-pin, MDI) Port Pinouts
RJ45 (8-pin, MDI-X) Port Pinouts
Pin
Signal
Pin
Signal
1
2
3
6
Tx+
Tx-
Rx+
Rx-
1
2
3
6
Rx+
Rx-
Tx+
Tx-
1
8
1
8
- 4 -
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring
Straight-Through Cable
Switch Port
NIC Port
RJ45 Plug Pin 1
Cable Wiring
RJ45
Connector
RJ45
Connector
Tx+
Tx-
Rx+
Rx-
3
6
1
2
3
6
1
2
Rx+
Rx-
Tx+
Tx-
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring
Cross-Over Cable
Switch Port
(NIC Port)
Switch Port
(NIC Port)
RJ45 Plug Pin 1
RJ45
RJ45
Connector
Cable Wiring
Connector
(Rx+) Tx+
(Rx-) Tx-
(Tx+) Rx+
(Tx-) Rx-
3
6
1
2
1
2
3
6
Rx+ (Tx+)
Rx- (Tx-)
Tx+ (Rx+)
Tx- (Rx-)
100BaseFX Fiber Port Connection
The concept behind the SC port and cable is quite straightforward. Suppose
you are connecting devices I and II. Contrary to electrical signals, optical
signals do not require a circuit in order to transmit data. Consequently, one of
the optical lines is used to transmit data from device I to device II, and the
other optical line is used transmit data from device II to device I, for
full-duplex transmission.
All you need to remember is to connect the Tx (transmit) port of device I to the
Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II. If you are making your own cable, we suggest
labeling the two sides of the same line with the same letter (A-to-A and B-to-B,
as shown below, or A1-to-A2 and B1-to-B2).
SC-Port Pinouts
SC-Port to SC-Port Cable Wiring
A
B
A
B
Tx
Cable Wiring
Rx
A
B
A
B
ST-Port Pinouts
ST-Port to ST-Port Cable Wiring
Cable Wiring
A
B
A
B
Tx
A
B
A
B
Rx
- 5 -
ATTENTION
This is a Class 1 Laser/LED product. Do not stare into the
Laser Beam.
Switch Settings
There is 1 set of DIP switches on the board. The following figure and table
give the settings for the 5-connector DIP switch.
DIP
1
2
3
4
Function
Auto Negotiation
Force TP Speed
Force TP Duplex
Link Fault Pass Through Enable
Operating Mode
ON
OFF
Enable
100 M
Disable
10 M
Full Duplex
Half Duplex
Disable
5
Store-and-Forward Pass Through
1. All the DIP settings default to “ON”.
NOTE
2. When configured for Pass Through mode, the Ethernet port
and fiber port should transmit at 100 Mbps, which is
equivalent to full duplex mode.
LED Indicators
There are 2 LEDs on the front bracket of the CSM-200 slide-in modules.
LED
Color
State
Function
On
Power is being supplied to power input.
PWR
Green
Power is not being supplied to power
input.
Off
On
FX port’s 100 Mbps is active.
Fiber Link Green
Blinking Data is being transmitted at 100 Mbps.
Off
On
100BaseFX port is inactive.
TP port’s 10 Mbps is active.
10M (TP)
Yellow
Blinking Data is being transmitted at 10 Mbps.
Off
On
TP port’s 10 Mbps link is inactive.
TP port’s 100 Mbps is active.
100M (TP) Green
Blinking Data is being transmitted at 100 Mbps.
Off
TP Port’s 100 Mbps is inactive.
- 6 -
Auto MDI/MDI-X Connection
The Auto MDI/MDI-X function allows users to connect the Moxa CSM-200’s
10/100BaseTX ports to any kind of Ethernet device, without needing to
determine the type of Ethernet cable being used for the connection.
This means that you can use either a straight-through cable or cross-over cable
to connect the CSM-200 Series to Ethernet devices.
Dual Speed Functionality and
Switching
The Moxa CSM-200’s 10/100 Mbps RJ45 Ethernet port auto negotiates with
the connected device for the fastest data transmission rate supported by both
devices. All models of the CSM-200 Series are plug-and-play devices, so that
software configuration is not required at installation, or during maintenance.
The half/full duplex mode for the RJ45 Ethernet ports is user dependent and
changes (by auto-negotiation) to full or half duplex, depending on which
transmission speed is supported by the attached device.
Auto-Negotiation and Speed Sensing
All of the CSM-200’s RJ45 Ethernet ports independently support
auto-negotiation for 10BaseT and 100BaseTX transmission speeds, with
operation according to the IEEE 802.3u standard.
This means that some nodes could be operating at 10 Mbps, while at the same
time other nodes are operating at 100 Mbps.
Auto-negotiation takes place when an RJ45 cable connection is made, and then
each time a LINK is enabled. Moxa’s CSM-200 advertises its capability for
using either 10 Mbps or 100 Mbps transmission speeds, with the device at the
other end of the cable expected to advertise similarly. Depending on what type
of device is connected, this will result in agreement to operate at a speed of
either 10 Mbps or 100 Mbps.
If a Moxa CSM-200 RJ45 Ethernet port is connected to a non-negotiating
device, it will default to 10 Mbps speed and half-duplex mode, as required by
the IEEE 802.3u standard.
- 7 -
Specifications
Technology
Standards
IEEE 802.3 for 10BaseT,
IEEE 802.3u for 100BaseT(X), 100BaseFX
Interface
RJ45 ports
10/100BaseT(X)
Fiber ports
100BaseFX (SC/ST connector)
PWR, Fiber Link, 10/100M(TP port)
LED Indicators
Optical Fiber
100BaseFX
Multi-mode Single-mode
Wavelength
Max. TX
Min. TX
RX Sensitivity
Link Budget
1300 nm
-10 dBm
-20 dBm
-32 dBm
12 dB
1310 nm
0 dBm
-5 dBm
-34 dBm
29 dB
5 km a
4 km b
-6 dBm
Typical Distance
Saturation
40 km c
-3 dBm
a. 50/125 μm, 800 MHz*km fiber optic cable
b. 62.5/125 μm, 500 MHz*km fiber optic cable
c. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable
Physical Characteristics
Housing
Dimensions
Weight
SPCC
86.8 x 124.3 x 21 mm (3.42 x 4.89 x 0.83 in)
Product only:
CSM-1213: 115 g (0.25 lb)
CSM-1214/1218: 125 g (0.28 lb)
Packaged:
CSM-1213: 170g (0.37 lb)
CSM-1214/1218: 180g (0.40 lb)
Environmental Limits
Operating Temperature
Storage Temperature
Humidity
0 to 60°C (32 to 142°F)
-20 to 75°C (-4 to 158°F)
5 to 95 % RH
Power Requirements
Input Voltage
12 VDC
Power Consumption
Regulatory Approvals
CE
180 mA @ 12 VDC
Class A
FCC
Part 15 sub part B class A
- 8 -
EMS
EN61000-4-2 (ESD), Criteria A, Level 4
EN61000-4-3 (RS), Criteria A, Level 2
EN61000-4-4 (EFT), Criteria A, Level 3
EN61000-4-5 (Surge), Criteria A, Level 3
EN61000-4-6 (CS), Criteria A, Level 2
En61000-4-8 (PFMF), Criteria A, Level 3
IEC 60068-2-32
Freefall
Warranty
Warranty Period
5 years
Technical Support Contact Information
Moxa Americas:
Toll-free: 1-888-669-2872
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
Fax:
+1-714-528-6777
+1-714-528-6778
Tel:
Fax:
+86-21-5258-9955
+86-10-6872-3958
Moxa Europe:
Moxa Asia-Pacific:
Tel:
Fax:
+49-89-3 70 03 99-0
+49-89-3 70 03 99-99
Tel:
Fax:
+886-2-8919-1230
+886-2-8919-1231
|