Mini Automobile SPARE AIR User Manual

 
IMPORTANT SAFETY PRECAUTIONS!  
WARNING: Do not use product until you have read and understand  
instructions and precautions.  
Submersible Systems, Inc. promotes responsible diving practices and the  
recommendations that have been promoted by all International Training agencies,  
including, but not limited to:  
• Before any attempt is made to use this product underwater, you MUST have  
received TRAINING and CERTIFICATION in the technique of SCUBA diving from  
a recognized certification agency. Use of this equipment by a person who is not  
certified by a recognized agency shall render all warranties, express or implied,  
null and void. Use of underwater breathing devices by uncertified or untrained  
persons is dangerous and can result in severe injury or death.  
• SPARE AIR is an EMERGENCY alternate air source. It is NOT designed or  
intended for any other use.  
• SPARE AIR should not be used as part of your planned air reserve.  
• SPARE AIR does not meet the requirements of EN 250; 1993 and therefore  
should never be used as a primary air source.  
• SPARE AIR is intended for use in water greater or equal to 10 degrees Celsius.  
• Recommended Max ascent rates: 15 meters per minute (6 meters per minute  
for the last 6 meters).  
• Swimming diver accepted as 25 Iiters/min., non-swimming will be less.  
• Monitor diving disorders if ascent rates are exceeded or decompression stops  
are missed.  
• Max depth recommendation is 20 meters (66 ft) for model #170.  
• Max depth recommendation is 30 meters (99 ft) for model #300/300-N.  
• Practice using SPARE AIR at normal rate ascents in shallow water.  
• ALWAYS follow Submersible Systems’ recommended pre-dive standards/post-  
dive checklist and annual inspection/repair guidelines.  
• NEVER dive with a SPARE AIR system that shows signs of damage, leakage or  
substandard performance.  
• NEVER OVERFILL the SPARE AIR system above 3000 psi, the air pressure  
stamped on the cylinder. ONLY use purified, dry compressed breathing air when  
refilling SPARE AIR.  
• STORE THE SPARE AIR system PRESSURIZED in a cool, dry place. Avoid  
direct sunlight, automobile trunks or other areas subject to temperature  
extremes.  
• In Europe, Cylinders fitted to SPARE AIR should meet national regulations and  
be tested and inspected in accordance with national regulations.  
• EC type approval conducted by: SGS United Kingdom, Ltd., Ellesmere Port,  
Cheshire, CH65 3EN, UK. Notified Body No. 0120. This item complies with MOD  
(PE) Specification RO347. May 1991.  
• This manual is supplied to the original SPARE AIR purchaser. Duplicate copies  
can be obtained free of charge from Submersible Systems, Inc.  
 
3
PURGE BUTTON  
(optional)  
(Refill Port)  
Model Specifications  
Model #300YEL/300-N  
Model #170YEL  
1.7 cu ft / 48 liters  
8.75” / 22.23 cm  
2.25” / 5.71 cm  
3000 psi / 200 bar  
1.51 lb / .687 kg  
30  
Maximum Capacity  
Length  
3.0 cu ft / 85 liters  
13.4” / 34 cm  
Diameter  
2.25” / 5.71 cm  
3000 psi / 200 bar  
2.17 lb / .985 kg  
57  
Maximum Pressure  
Weight (full)  
Surface Breaths*  
Water Volume  
26.62 cu in / .42 liters  
13.7 cu in / .28 liters  
*Based on 1.6 liter breath size  
 
4
SPARE AIR HOLSTER #973  
Mount SPARE AIR in a variety of locations on virtually any BCD!  
Upside Down On  
Your Tank Strap  
Vertical On Your  
BC  
Diagonal  
Across Your  
Waist  
 
5
SPARE AIR REFILL ADAPTER #910S  
Adapter fits onto Standard SCUBA tank for easy refilling.  
 
6
BEFORE YOU DIVE WITH SPARE AIR  
• SPARE AIR shipped empty - fill prior to use.  
SPARE AIR is always ON and ready for use. The White Pressure  
Indicator Pin should extend flush with the top of the Pressure  
Indicator Gauge indicating that the unit is full. (The optional Dial  
Gauge indicator will show full when dial is at “3”.) If Pressure  
Indicator Pin is less than flush SPARE AIR MUST be refilled. Do not  
dive until you have refilled SPARE AIR. See refilling instructions on  
page 12.  
Push Purge Button down and release. Purge Button should move  
up and down freely. To maintain full pressure in SPARE AIR do not  
use purge unnecessarily.  
Make sure SPARE AIR is mounted firmly and adjusted properly in  
Holster before entering the water. Velcro must be fully engaged.  
NOTE: For added security  
a
safety leash/lanyard is  
recommended so that SPARE AIR is not lost if it is dislodged,  
dropped or released by accident. Hold SPARE AIR secure  
with a free hand on entry into the water or in rough surf or  
currents.  
HOW TO MOUNT SPARE AIR  
1. Determine where on BC you would like to mount SPARE AIR.  
Look for an area that has 2 places to attach the Quick  
Disconnect Straps (on D-rings, Straps, etc.)  
2. The Straps are movable by threading them through any of the  
webbing sections on back of Holster. Choose the 2 that would  
allow for the tightest fit possible.  
 
7
3. Snap Quick Disconnect Straps around mounting point on BC  
and cinch up so Holster is snug against the BC.  
4. Attach SPARE AIR leash snug around neck of cylinder and clip  
other end onto Holster or BC D-ring.  
5. Insert SPARE AIR into Holster and secure velcro on top flap,  
attach Mouthpiece Cover.  
6. Try on BC and try removal of SPARE AIR several times to become  
comfortable with the steps necessary to remove the unit.  
HOW TO OPERATE SPARE AIR  
1. Upon ascent, pull D-ring on flap of Holster to open.  
CAUTION: Begin ascending immediately to avoid using  
valuable time and air.  
2. Grab SPARE AIR regulator head and pull out of the Holster. This  
action will release the Mouthpiece Cover.  
3. Place SPARE AIR into user’s mouth.  
4. Press Purge Button lightly or exhale sharply to clear regulator  
before inhaling.  
CAUTION: Failure to purge the SPARE AIR regulator before  
inhaling will result in swallowing water.  
5. Continue to inhale and exhale to a safe and normal rising rate of  
ascent.  
NOTE: SPARE AIR is only for use to recreational depths.  
Never deplete SPARE AIR entirely in a SIMULATED ascent,  
water will enter inner stages of regulator and may result in  
internal corrosion.  
 
8
IMPORTANT WARRANTY INSERT  
Congratulations!  
You've just joined the ranks of over 200,000 discriminat-  
ing divers who enjoy the peace of mind of diving with  
SPARE AIR .  
SPARE AIR is the absolute best strategy for successful-  
ly dealing with out-of-air emergencies, because it is a  
completely independent air supply.  
Submersible Systems is proud of the fact that we  
contribute to divers' safety. Every year more and more  
lives are saved because of SPARE AIR. SPARE AIR  
continues to be refined out of our commitment to provide  
our customers with a Simply Dependable product.  
SPARE AIR is made entirely in the U.S.A. by craftsmen  
dedicated to producing a quality product.  
Send in your warranty  
card NOW in order to be  
eligible for our monthly  
accessory drawing!!!!  
 
Important Warranty Information  
Retain this section for your records  
_____________________________________________________________________ ____________________________________________________________________  
Name  
_____________________________________________________________________ ____________________________________________________________________  
Authorized Dealer’s Name Dealer’s Address  
___________________________________________________________________________ Model # I 170YEL I 300YEL I 300-N  
Purchase Date Regulator Serial #  
Address  
Submersible Systems Limited One-Year Warranty  
Statement of Warranty  
Submersible Systems, Inc. (SSI) guarantees, to the original purchaser only, that  
the product purchased will be free of defects in materials and/or craftsmanship  
under normal SCUBA use for one year from date of purchase provided proper  
care has been performed as prescribed by the owner's manual supplied along  
with the product. Should this product prove to be defective for any reason (other  
than those listed in the limitations section below) the product will be repaired or  
replaced (at SSl's discretion) free of charge (excluding shipping and handling  
charges.) This warranty shall be considered null and void if the registration card  
is not filled out completely and mailed to SSI within 15 days of purchase. This  
warranty is non-transferable and applies to the original purchaser only.  
How to obtain warranty service  
You must return your product to Submersible Systems to obtain warranty  
service. You must provide a copy of the original sales receipt and a copy of the  
owner's portion of this warranty registration. Freight must be prepaid. Please  
enclose a letter with your daytime telephone number describing the exact nature  
of the difficulty you are experiencing.  
Statement of Limitations  
General Warranty does not cover damage from accident, abuse, tampering, lack  
of proper care and maintenance and/or improper annual servicing. Modifications  
or repair by anyone other than an SSI Authorized Repair Facility voids warranty.  
SSI will not be responsible for recovery or replacement of the product in the  
event of loss or theft. SSI, its distributors, and retailers make no warranties, either  
expressed or implied, with respect to this product or its accompanying owner's  
manual except those stated in the preceding paragraphs. By purchasing this  
product it is agreed and understood that in no event will SSI, its distributors or  
retailers be held liable for any personal injuries resulting from its operation, or for  
any other damages whether direct, indirect, incidental, or consequential even if  
SSI has been advised of such damages.  
PLEASE READ ALL INSTRUCTIONS AND FOLLOW ALL PRE-AND-POST-DIVE  
PROCEDURES. REMEMBER THAT THE BEST WARRANTY IS PREVENTATIVE  
MAINTENANCE. HAVE YOUR SPARE AIR SERVICED ANNUALLY!  
 
Submersible Systems Limited  
One-Year Warranty Registration  
This registration card must be filled out and returned within 15 days of purchase for warranty coverage. Please print.  
Last Name  
Street Address  
City  
First Name  
MI  
Apt. #  
Country  
State  
Zip/Postal Code  
Phone  
Date of Purchase  
month/date/year  
Regulator Serial #  
Dealer’s Address  
Authorized Dealer’s Name  
E-Mail Address (for special offers, important product information)  
Model # I 170YEL I 300YEL I 300-N  
Number of Years Diving  
I Less than 1  
I 1-3  
I 4-6  
I 7+  
Average Number of Dives per Year  
I 1-12  
I 13-25  
I 26-50  
I 51-100  
I 100+  
Certification Level  
I Advanced  
I Rescue  
I Divemaster  
I Other  
I Open water  
I Instructor  
Age Group  
I Under 18  
I 18-25  
I Female  
I 26-35  
I 36-45  
I 46-50  
I 51+  
Sex  
I Male  
What influenced your purchase?  
I Magazine ad  
I Magazine editorial I Brochure  
I Store display  
I Store personnel  
I Instructor I Dive Buddy  
I Other ____________________________________________________________________  
Occupation _____________________________________________________________________________________________________  
Why did you purchase SPARE AIR? ___________________________________________________  
____________________________________________________________________________________________  
 
 
AFTER YOU DIVE WITH SPARE AIR  
1. Visually check the Pressure Indicator Gauge and press Purge  
Button.  
2. White Indicator Pin should be extended and airflow should occur.  
This ensures pressure was maintained during your dive.  
NOTE: If Indicator Pin is not extended or no air flow occurs,  
water and contaminants may have entered the regulator’s  
internal stage and could lead to corrosion and/or failure of the  
system. Contact your Authorized SPARE AIR Dealer or  
Submersible Systems, Inc. for service and/or check-up.  
3. Remove SPARE AIR from the Holster to rinse and dry.  
4. With pressure in the SPARE AIR, rinse or soak in fresh water for 30  
minutes and run fresh water inside the mouthpiece and around the  
regulator.  
5. Shake excess water from the system and dry thoroughly.  
CAUTION: Never use chemicals or solvents to clean SPARE AIR.  
PRODUCT COMPATIBILITY  
AND USE WITH NITROX–MODEL 300-N  
• Submersible Systems Nitrox SPARE AIR shall not be used with Pure  
Oxygen, or Nitrox with greater than 40% Oxygen.  
• Only gas from storage and supply equipment cleaned and  
maintained for Oxygen Service is acceptable for use with Nitrox  
SPARE AIR.  
 
9
• If the SPARE AIR Nitrox is used with equipment or connected to air  
supply systems which are not rated for Oxygen Service, it will be  
considered contaminated and will require cleaning for Oxygen  
Service prior to use again with Nitrox.  
• Equipment users must be trained and certified in the specific use of  
Nitrox by dive industry training agencies.  
• Only a halocarbon based lubricant such as Christo-Lube MCG 111  
should be used on SPARE AIR Nitrox.  
HOW TO CARE FOR YOUR SPARE AIR  
Providing the best possible preventative maintenance and  
following routine pre- and post-dive steps diligently will help to  
ensure the maximum life of your SPARE AIR system. SPARE AIR  
should be serviced ANNUALLY by an Authorized SPARE AIR  
Dealer or by Submersible Systems, Inc.  
If you notice damage, wear or suspect any leaking or missing  
parts, have SPARE AIR examined by an Authorized SPARE AIR  
Dealer immediately.  
WARNING: DO NOT attempt to repair SPARE AIR yourself.  
Unauthorized repairs or tampering are hazardous and WILL  
VOID your warranty.  
The SPARE AIR cylinder has a DOT 3AL3000 rating and will require  
HYDROSTATIC TESTING EVERY FIVE (5) YEARS and a VISUAL  
INSPECTION ANNUALLY. Keep the Threads on both the Check  
Valve and Refill Adapter clean and lubricated. Use a high-quality,  
non-toxic, food grade spray silicone for best results.  
WARNING: NEVER use a hydrocarbon based oil (i.e.  
household oil or motor oil).  
 
10  
HOW TO TRAVEL WITH SPARE AIR  
1. When taking Spare Air on commercial aircraft TSA  
(Transportation Security Administration) requires air cylinders to  
be empty. Purge Spare Air until empty of air.  
2. Remove regulator from cylinder (they are attached hand tight) by  
turning counter clock-wise. Leave o-ring, washer etc. on the  
regulator.  
3. Pack Spare Air in your check on luggage (NOT carry on).  
4. Notify counter personnel when checking in for your flight that you  
have a Spare Air mini-breathing system that is empty and  
disassemble in your luggage.  
5. When you reach your dive destination, reassemble Spare Air and  
refill.You may lightly lubricate the tank 0-ring with a small amount  
of silicone spray or grease – never use a hydrocarbon based oil.  
Do not force regulator onto tank – if you feel resistance stop and  
unscrew and start again.  
6. Replace tank o-ring after product has been disassembled and re-  
assembled 3 times, or o-ring shows signs of wear or air leakage.  
7. Keep Spare Air regulator and cylinder threads clean and dry.  
Note: We recommend the purchase of the SPARE AIR Travel  
Pack #963 which includes a durable plastic carrying bag, 3  
extra tank o-rings and protective caps for the regulator and  
cylinder threads (go to website for more information).  
Note: This product, Spare Air, is an emergency breathing  
system that utilizes breathing air and is not hazardous.  
 
11  
HOW TO REFILL SPARE AIR  
NOTE: Always refill SPARE AIR immediately after use,  
so the system is ready for subsequent use.  
CAUTION: DO NOT stand directly over top of  
SPARE AIR regulator while filling.  
A feature of this adapter is that as you rotate the knurled ring  
on the adapter to the right it automatically closes the vent.  
When unscrewing to the left it vents the pressure, allowing the  
adapter to unscrew easily.  
1. Unscrew black knurled Cap from the SPARE AIR Check  
Valve filling port.  
2. Place the Adapter onto Check Valve and turn the knurled  
part of the adapter to the right until finger tight.  
3. Attach Adapter to SCUBA tank valve.  
4. Fill (Important: Gently open SCUBA valve to fill slowly, take  
45 – 60 seconds to fill). The pin on the Pressure Indicator  
will rise while filling and when flush with the top unit is full  
at 3000 psi. For Dial Gauge option, unit is full when needle  
points to 3.  
5. Close SCUBA tank valve.  
6. Turn the knurled part of the Adapter to the left to relieve  
pressure in the adapter.  
 
12  
7. Remove Adapter from SCUBA tank and SPARE AIR.  
8. Replace black knurled Cap on Check Valve.  
NOTE: If air is escaping from the adapter during filling,  
close tank valve, wait for air to stop and retighten  
knurled ring by turning to the right.  
NOTE: If SCUBA tank WAS NOT FULL at beginning of  
refill procedure, then the pressure indicator will not  
show full and your SPARE AIR will not be filled to its  
recommended full capacity, diminishing available air  
volume.  
WARNING: If the SPARE AIR check valve or adapter  
threads are damaged or worn these parts will require  
replacement. Continued use may cause injury.  
If you have any questions concerning this product,  
please call:  
Submersible Systems, Inc. Customer Service at  
800-648-3483 or 714-842-6566  
8 am-5pm PST, Monday-Friday,  
or log on to our website at  
 
13  
ANNUAL SERVICE RECORDS  
Date:_____________________________________________________________________________________________________________  
By: _______________________________________________________________________________________________________________  
Comments: ___________________________________________________________________________________________________  
____________________________________________________________________________________________________________________  
Date: ____________________________________________________________________________________________________________  
By: _______________________________________________________________________________________________________________  
Comments: ___________________________________________________________________________________________________  
____________________________________________________________________________________________________________________  
Date: ____________________________________________________________________________________________________________  
By: _______________________________________________________________________________________________________________  
Comments: ___________________________________________________________________________________________________  
____________________________________________________________________________________________________________________  
Distributor Stamp:  
18072 Gothard Street, Huntington Beach, CA 92648 USA  
Rev. 5/04  
 
14  
SPARE AIR ACCESSORY ORDER FORM  
Call your local dive shop or log on to our website at www.spareair.com to order  
SPARE AIR accessories or order direct by mail:  
Model#  
003DGS  
Bag  
Description  
Price  
Qty  
Dial Gauge Pressure Indicator  
$64.00  
$12.00  
$14.00  
$54.00  
$30.00  
$30.00  
$28.00  
Drawstring Nylon Carrying Bag  
Safety Leash (Lanyard that prevents accidental loss)  
Scuba Tank Refill Adapter  
961  
910S  
973  
SPARE AIR Holster (Fits 3.0 cu. ft. models)  
SPARE AIR Holster (Fits 1.7 cu. ft. models)  
Air Compressor Refill Adapter  
971  
920C  
963  
SPARE AIR Travel Pack (Includes durable plastic carrying bag,  
3 extra tank o-rings and protective caps for the regulator  
and cylinder threads)  
$12.00  
Ship To:  
Sub Total  
$
U.S.  
Shipping  
Name  
_____________________________________________________  
$8.00  
Address _____________________________________________________  
City, State, Zip ________________________________________________  
Country _____________________________________________________  
Shipping  
Abroad  
$15.00  
$
Total  
Phone (___________) __________________________________________  
Method of Payment:  
I Check Enclosed  
I VISA / MasterCard / AMEX  
(circle one)  
Credit Card # ________________________________________________________________________________________________________  
Exp. Date ______________________________________________________________________________________________________________  
Name on Card ________________________________________________________________________________________________________  
Signature ______________________________________________________________________________________________________________  
*Allow 3-4 weeks for delivery  
 
15  
Mail order form to:  
Submersible Systems, Inc.  
18072 Gothard Street  
Huntington Beach, CA 92648 USA  
or  
Log on to our website at  
to purchase  
SPARE AIR Accessories  
Distributor Stamp:  
18072 Gothard Street, Huntington Beach, CA 92648 USA  
 
Rev. 5/04  
#098128NX  

Miele Freezer F 12020 S User Manual
Mr Handsfree Telephone Handsfree Kit User Manual
MTD Spreader 439 305 User Manual
NAD Stereo System 4020A User Manual
National Instruments Network Card SCXI 1125 User Manual
NEC Home Theater System NP60J User Manual
Northern Industrial Tools Impact Driver 150611 User Manual
Onkyo Car Stereo System TX RZ900 User Manual
Oster Food Warmer 133704 User Manual
Panasonic Cell Phone EB GD76 User Manual