Operating and Installation
Instructions
Ventilation System
DA 398-5
DA 399-5
en - US
To prevent accidents
and appliance damage,
read these instructions
before
installation or use.
M.-Nr. 07 759 400
Contents
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the Ventilation System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning on the fan s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting the power level - / + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overhead lighting I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning the casing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Active charcoal filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Appliance dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Structural support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Protective film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
TO REDUCE THE RISK OF
READ AND SAVE THESE
INSTRUCTIONS
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
Keep these instructions in a safe
place and pass them on to any future
user.
OBSERVE THE FOLLOWING:
a) Use this appliance only in the
~
manner intended by the manufacturer.
If you have questions, contact Miele.
Read these instructions carefully
before installing or using the
Ventilation System.
b) Before servicing or cleaning the
~
appliance, switch power off at the
service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally. If
the service disconnecting means
cannot be locked, securely fasten a
prominent warning device, such as a
tag, to the service panel.
This appliance is intended for
~
residential use only. Use the appliance
only for its intended purpose.
This appliance complies with current
~
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
c) Be certain your appliance is
~
,CAUTION
properly installed and grounded by a
qualified technician.
For General Ventilating Use
Only. Do Not Use To Exhaust
Hazardous Or Explosive
Materials And Vapors.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician.
This appliance is designed to vent
~
cooking smoke and odors only.
This appliance is suitable for
~
installation above gas or electric
cooking surfaces.
This appliance is not designed for
~
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions installation in these
applications may be possible. Please
contact your Miele dealer or the Miele
Technical Service Department with
specific requirements.
4
IMPORTANT SAFETY INSTRUCTIONS
d) Before connecting the appliance
~
to the power supply make sure that the
Use
voltage and frequency listed on the
data plate correspond with the
household electrical supply.
,WARNING
TO REDUCE THE RISK OF A
COOKTOP GREASE FIRE:
This data must correspond to prevent
appliance damage. If in doubt consult a
qualified electrician.
a) Never leave surface units
~
unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
e) Installation work and repairs
~
should only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous.
b) Always turn the hood on when
~
cooking at a high heat.
c) Clean the ventilation hood
~
f) Only open the housing as
frequently. Grease should not be
allowed to accumulate on the fan or
filter.
~
described in the enclosed "Installation
diagram" and in the "Cleaning and care"
section of this manual. Under no
circumstances should any other parts
of the housing be opened. Tampering
with electrical connections or
d) Use the proper pan size. Always
~
use cookware appropriate for the size
of the cooking area.
components and mechanical parts is
highly dangerous to the user and can
cause operation faults.
e) Do not flambé or grill with an
~
open flame beneath the hood.
Flames could be drawn up into the
hood by the suction and the grease
filters may catch fire.
g) Before discarding an old
~
appliance, disconnect it from the power
supply and remove the power cord to
prevent hazards.
5
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
Do not allow children to play with or
~
operate the appliance or its controls.
TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE
EVENT OF A COOKTOP
GREASE FIRE, OBSERVE THE
FOLLOWING*:
Supervise its use by the elderly or
infirm.
Always turn on the hood when using
~
the cooktop to prevent damage from
condensation.
a) SMOTHER FLAMES with a close
~
Never operate gas burners without
~
fitting lid, cookie sheet, or metal tray
then turn off the burner.
cookware. Turn the burner off when not
in use. Adjust the burner so that the
flames do not extend beneath the
cookware. Do not overheat the
cookware, e.g. when using a wok. The
hood can be damaged due to
excessive heat from the burners and
the cookware.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
b) NEVER PICK UP A FLAMING
~
PAN - You may be burned.
c) DO NOT USE WATER, including
Do not use the hood without the
~
grease filters in place.
~
wet dishcloths or towels - a violent
steam explosion will result.
Do not use a steam cleaner to clean
~
d) Use a fire extinguisher ONLY if:
the hood. Steam could penetrate
electrical components and cause a
short circuit.
~
1) You have a class ABC
extinguisher, and you know how to
operate it.
2) The fire is small and contained in
the area where it started.
3) The fire department is being
called.
4)You can fight the fire with your
back to an exit.
*
Based on "Kitchen Firesafety Tips"
published by NAFTA
6
IMPORTANT SAFETY INSTRUCTIONS
Installation
g) Do not install this hood over
~
cooktops that burn solid fuel.
,WARNING
h) Provided a larger distance is not
~
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and the
bottom of the hood given in the
"Appliance dimensions" section of this
manual.
OBSERVE THE FOLLOWING:
a) Installation work and electrical
~
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
If local building codes require a greater
safety distance, follow their
requirement.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
b) Sufficient air is needed for
~
combustion and exhausting of gases
through the flue (chimney of fuel
burning equipment to prevent back
drafting. Follow the heating equipment
manufacturer’s guideline and safety
standards such as those published by
the National Fire Protection Association
(NFPA) and the American Society for
Heating, Refrigeration and Air
i) Never connect an exhaust hood to
~
an active chimney, dryer vent, vent flue,
or room ventilating ductwork.
j) Seek professional advice before
~
connecting an exhaust hood vent to an
existing, inactive chimney or vent flue.
Conditioning Engineers (ASHRAE), and
the local code authorities.
k) Any fittings, sealant, or materials
~
used to install the ductwork must be
made of approved non-flammable
materials.
c) When cutting or drilling into the
~
wall or ceiling, do not damage electrical
wiring and other hidden utilities.
d) Ducted hoods must always be
~
vented to the outdoors.
,WARNING
TO REDUCE THE RISK OF
FIRE USE ONLY METAL
DUCTWORK.
e) Do not use this hood with any
~
solid-state speed control device.
f) Do not use an extension cord to
~
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance,
(e.g. danger of overheating).
7
Guide to the Ventilation System
8
Guide to the Ventilation System
aTelescopic extension piece
bChimney
cCanopy
dControl panel
eGrease filter
fRecirculation vent
(recirculation mode only)
gOverhead lighting
hCharcoal filter
(optional accessory for recirculation
mode)
iOn/Off button
jFan power selection
kOn/Off button for the overhead
lighing
9
Functional description
The hood offers two modes of operation:
Air extraction
Recirculation mode
Air is drawn through the grease filters
and an active charcoal filter. The
filtered air is then recirculated back into
the kitchen through a vent at the top of
the hood’s chimney.
The air is drawn in and cleaned by the
grease filters and directed outside.
The hood comes equipped with a
non-return flap. This flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occur. When the hood is
turned on, the air pressure of the
exhaust fan automatically opens the
flap blowing the inside air and cooking
odors outside.
The recirculation mode requires an
install kit and charcoal filter which are
optional accessories.
Before using the hood in
recirculation mode, ensure that the
active charcoal filter is in place, see
"Cleaning and care".
10
Operation
Turning on the fan s
^ Press the On/Off button s.
The fan turns on to Level "II".
Automatically switching back the
intensive power level
The intensive level can be programmed
to automatically switch back to level 3
after 10 minutes.
^ Turn the fan and the overhead
lighting off.
Selecting the power level - / +
^ Press the "–" symbol to select a lower
power level or the "+" symbol for a
higher power level.
^ Press and hold the - and + buttons
for approx. 10 seconds until power
level indicator 1 lights up.
Depending on the amount of cooking
odors, levels 1 to 3 are usually sufficient
for normal cooking.
^ Then press the following buttons one
after another :
– light I,
Intensive setting
– the "–" button, and
– the light button I again.
Level "4" should only be used for short
periods of time when frying or cooking
food with a strong aroma.
If the indicators 1 and 4 flash, the
automatic switch back is not activated.
^ To activate the automatic switch
back, press the "+" button.
The power level indicators 1 and 4
light continuously.
To deactivate, press the "–" button.
^ Press the On/Off s button to confirm
the setting.
If the procedure is not stored within 4
minutes, the hood will automatically
default to the original setting
11
Operation
Turning off the fan s
^ Press the On/Off button to turn the
fan off K.
The K indicator goes out.
Overhead lighting I
The overhead lighting can be turned on
and off independently of the fan.
^ Press the light button I briefly to
turn on the lighting.
Automatic Safety Shut-Off
The fan will turn automatically off 10
hours of use. The lighting however will
remain on.
^ Press the On/Off button K to turn the
fan back on again.
12
Cleaning and Care
,WARNING
The following instructions for cleaning
"Stainless steel" surfaces and "Stainless
steel colored controls" should be
followed in addition to the general
"Cleaning the casing" instructions.
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Special instructions for stainless
steel surfaces
Before cleaning or servicing the
hood, disconnect it from the power
supply, see "Important Safety
Instructions".
(not applicable to the controls)
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
Cleaning the casing
To help prevent resoiling, a conditioner
for stainless steel can be applied.
Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
will damage the surface.
Special instructions for colored
casings
^ All external surfaces and controls can
be cleaned with a mild solution of
warm water and liquid dish soap
applied with a soft sponge.
(Special order)
It is very difficult to clean this type of
surface without causing minor marks to
the surface material. This can become
particularly noticeable with darker
colors and if there is halogen lighting in
the kitchen.
Do not use too much water when
cleaning the controls. Water could
penetrate the electronics and cause
damage.
Stainless steel colored controls
^ Wipe dry using a soft cloth.
These controls may become dis-
colored or damaged if not cleaned
regularly.
Avoid:
– cleaning agents containing soda,
acids or chlorides,
Do not use a stainless steel cleaner
on these controls.
– abrasive cleaning agents
e.g. powder or cream cleansers,
– abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents.
These will damage the surface.
13
Cleaning and Care
Grease filters
Cleaning the grease filter
The reusable metal grease filters in the
hood remove solid particles from the
vented kitchen air (grease, dust, etc)
and prevent soiling of the ventilation
system.
^ By hand: use a scrub brush with a
solution of warm water and mild
detergent.
Do not use the pure detergent,
aggressive all purpose cleaners,
oven sprays, abrasive cleaning
agents or limescale removers. They
could destroy the filter.
The grease filters should be cleaned
every 3 - 4 weeks.
,A dirty filter is a fire hazard.
^ In a dishwasher: place the filter
vertically in the lower basket, making
sure that the spray arm is not
blocked.
Use a wash program with a max.
temperature of 150°F (65°C). In a
Miele dishwasher use the "Normal"
program.
Use the recommended amount of
dishwasher detergent. Overuse could
destroy the filter.
Depending on the detergent,
cleaning the grease filter in a
dishwasher may cause permanent
discoloration of the filter surface.
Performance of the filter will not be
affected by this discoloration.
^ To remove the grease filter pull the
locking clips forward, lower the filter
down 45°, unhook it at the rear, and
take it out.
Support the grease filter so that it
does not fall and damage the
cooktop.
^ After cleaning, the filter can be
placed on a towel to air dry.
^ While the filters are removed, clean
any dirt or grease from the filter
casing.
14
Cleaning and Care
When putting the grease filters back
make sure that the locking clips are
visibly facing the cooking surface
Active charcoal filter
In recirculation mode an active
charcoal filter must be used in addition
to the grease filters. It is designed to
absorb cooking odors.
The active charcoal filter will be
replaced in the canopy above the
grease filters.
Replacement active charcoal filters
can be ordered from Miele.
^ If the filters are incorrectly installed,
insert a small screwdriver into the slit
along its edge to disengage it from
the casing.
^ To install or replace the charcoal
filter, the grease filters must first be
removed as described in the
previous section.
^ Remove the charcoal filter from the
packaging.
^ Slide the charcoal filter into the rear
of the filter frame, then raise the front
up and push it into the frame.
^ Replace the grease filters.
Replace the active charcoal filter at
least every 6 months or when they no
longer absorb odors efficiently.
^ Used charcoal filters may be
discarded in household trash.
15
Cleaning and Care
Changing the light bulb
^ Remove the grease filters.
,WARNING
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Before changing the light bulbs,
disconnect the hood from the power
supply, see "Important Safety
Instructions".
^ Turn the knurled screw
counterclockwise. The halogen lamp
will swivel down.
When in use halogen bulbs become
extremely hot, use caution. Do not
attempt to change the bulbs until
they have had sufficient time to cool.
Do not touch the bulb surface.
Fingerprints or body oils deposited
on the bulb will decrease its life.
Follow the bulb manufacturer’s
instructions.
^ Turn the bulb counterclockwise and
pull it out of its socket.
Use the same bulb type as a
replacement: GU/GZ10, 120V, 50W.
^ Replace the bulb with a new one in
the reverse order.
^ Replace the grease filters.
16
After Sales Service
Repairs
MieleCare
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department.
(USA only)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
^ When contacting the Technical
Service Department, please quote
the model and serial number of your
appliance.
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
These are shown on the data plate
which is visible when the grease filters
are removed.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
17
18
Installation Instructions
Read these instructions and the "Important Safety Instructions" before installing
this ventilation system.
The installation steps are described in the enclosed "Installation Diagram".
Leave these instructions with the appliance for the consumer/user.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
20
Caring for the environment
Disposal of packing material
Disposal of an old appliance
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old appliance,
disconnect it from the electrical
,DANGER
Ensure that any plastic wrappings,
bags, etc., are disposed of safely
and kept out of the reach of babies
and young children. Danger of
suffocation!
supply and cut off the power cord to
prevent it from becoming a hazard.
21
Appliance dimensions
Drawing is not to scale.
22
Appliance dimensions
a Ar extraction mode
b Recirculation mode
c Recirculation vent positioned at the
top (recirculation mode only)
d, e Installation area;
For recirculation mode only d.
Wall/ceiling area respectively for vent
hole and outlet installation.
For recirculation mode only the outlet
installation is required.
Connection for air extraction mode
6" (150 mm), with reducing collar
5" (125 mm).
23
Appliance dimensions
Distance between cooktop and hood (S)
Do not install this exhaust hood over cooktops burning solid fuel.
Provided a larger distance is not given by the manufacturer of the cooktop, follow
the minimum safety distances between a cooktop and the bottom of the hood:
Miele Cooktops
Non-Miele
Cooktops
Electric Cooktops
24" (610 mm)
26" (660 mm)
Electric Barbeques and Fryers
Multiburner Gas cooktops
< 43,000 BTU (12.6 KW)
26" (660 mm)
30" (760 mm)
and no burner > 15,000 BTU (4.5 KW)
Single burner (Wok) < 20,500 BTU (6 KW)
All other gas cooktops
26" (660 mm)
30" (760 mm)
30" (760 mm)
– If several gas surfaces are installed under the hood, the total output must be
considered when determining the minimum safety distance.
– Be sure to follow the minimum safety distances given by the gas cooktop
manufacturer to easily flammable materials e.g. upper cabinets.
– If local building codes require a greater safety distance, follow their requirement.
– If there is more than one appliance beneath the hood and they have different
minimum safety distances always select the greater distance.
See "Important Safety Instructions" for further information.
– To ensure free access to work under the ventilation hood, a distance of a
minimum of 26" (660 mm) above the electric cooktop is also recommended.
– Take the user's body height into consideration when selecting the installation
height. Adequate work space at the cooktop and optimal operation of the
ventilation system should be ensured.
– However, the greater the distance from the cooktop, the less effectively cooking
odors are drawn in.
– If the top of the hoods telescopic extension piece will be mounted flush to the
ceiling, regard the possible unit height when selecting the installation height.
24
Appliance dimensions
Drilling diagram
To prepare a backing plate, the
spacings for the 5 mm screws need to
be drilled as shown.
* The dimension between the ceiling
and the middle bracket may vary
depending on the position of the vent
cut-out and the power socket. It should
be installed as low as possible.
If the ventilation hood will be mounted
directly to the wall, follow the additional
instructions given in the included
"Installation diagram".
25
Plywood backing
^ Find the studs to the left and right of
the mounting location by tapping the
wall or using a stud finder.
The majority of the weight of the
installed ventilation system will be
supported by the lower retaining
plate. It must be firmly attached to
the stud framing behind the drywall.
If studs are not available in the
required locations, a plywood
backing (min. ½" (13 mm) thick)
spanning at least two studs must be
installed. Failure to adequately
support the weight as stated may
result in the ventilation system falling
off the wall, causing personal injury
and property damage.
^ Mark a vertical cutting line along the
center of each stud.
,CAUTION
When cutting or drilling into the wall
or ceiling, do not damage electrical
wiring and other hidden utilities.
^ Remove the drywall between the
cutting lines and replace it with
plywood of a matching thickness
(min. ½" (13 mm) thick). Tape the
joints and refinish the wall.
(If plywood backing is not needed,
proceed to the included "Installation
diagram".)
^ Proceed to the enclosed "Installation
diagram" to complete the installation.
To install a plywood backing
^ Determine and mark the location of
the retaining plate for the canopy as
outlined on the "Installation diagram".
^ Make a cutting line 3" (76 mm) above
and 3" (76 mm) below the outline of
the retaining plate.
26
Installation
Dismantling
Before installation read the
information in the "Dimensions" and
"Important Safety Instruction"
chapters.
If the hood needs to be disassembled,
follow the instructions on the
"Installation diagram" in the reverse
order.
Under certain conditions, there is a
danger of poisonous fumes by when
the ventilation system and a furnace
drawing interior air run at the same
time.
A lever is enclosed for easier removal
of the chimney extension.
Installation instructions
The individual installation steps are
described in the included Installation
diagram.
Protective film
(stainless steel units)
^ After removing the two screws from
the chimney, slide the lever between
the chimney and the chimney
The casing is covered with a protective
film to prevent scratching during
transport.
extension and gently apply pressure
to ease the chimney from its hooks.
^ Please peel off the film before
installing the casing parts. It can be
removed without tools.
27
Installation
Installation materials
28
Installation
a 3 protective shields
to prevent scratches to the chimney
during installation.
6 Screws 5 x 40 mm
b 1 vent collar
for use with 6" (150 mm) exhaust
ducting.
(S8 wall anchors included in the
packaging are not for use in USA / CDN)
The screws and wall anchors are
suitable for solid brick walls.
For other wall constructions, use
appropriate materials.
c 1 reducing collar
for use with 5" (125 mm) exhaust
ducting.
Ensure that the wall can support the
weight.
dUpper wall bracket
for securing the telescopic extension
piece
eMiddle wall bracket
for securing the telescopic extension
piece
2 M 6 locking nuts
for securing the motor assembly.
fLower wall bracket
for securing the ventilation system
g Installation kit for recirculation
mode
2 Screws 3.9 x 7.5 mm
contains diverter, hose and hose
clips (optional accessory).
for securing the chimney.
1 Lever
for dismantling the chimney.
Installation instructions
29
Electrical connection
,WARNING
Grounding Instructions
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
This appliance must be grounded. In
the event of an electrical short circuit,
grounding reduces the risk of electric
shock by providing a path of least
resistance. This appliance is equipped
with a cord having a grounding wire
with a grounding plug. The plug must
be plugged into an outlet that is
All electrical work should be
performed by a qualified electrician
in strict accordance with national
regulations (for USA: ANSI-NFPA 70)
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.
properly installed and grounded.
WARNING - Improper grounding can
result in a risk of electric shock.
If there is any doubt, have the electrical
system of the house checked by a
qualified electrician.
Ensure that power to the appliance
is off while installation or repair work
is performed.
Do not use an extension cord. If the
power supply cord is too short, have a
qualified electrician install an outlet
near the appliance.
^ Verify that the voltage, load and
circuit rating information found on the
data plate (located behind the
grease filters), match the household
electrical supply before installing the
hood.
Important
The hood comes equipped with a 4 ft
(1.2 m) power cord with a NEMA 5-15
molded plug for connection to a 120 V,
60 Hz, 15 A power outlet.
^ Use only with ventilation hood
cord-connection kits that have been
investigated and found acceptable
for use with this model hood.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or contact Miele’s
Technical Service Department.
U
V
1-800-999-1360
1-800-565-6435
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
30
Air extraction
Exhaust ducting and connections
,WARNING
Use smooth or flexible pipework made
from approved non-flammable
materials for exhaust ducting.
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
To reduce the risk of fire and to
properly exhaust air, the exhaust
gases extracted by the hood
should be vented outside of the
building only.
To achieve the most efficient air
extraction and quietest noise levels,
consider the following:
– The diameter of the ductwork should
not be less than 6" (150 mm).
– If flat ducting is used, the cross
section must not be smaller than the
cross section of the ventilation
exhaust.
Do not vent exhaust air into
spaces within walls or ceilings or
in attics, crawl spaces or garages.
– The ducting should be as short and
straight as possible.
– Use ductwork with a wide radius.
To reduce the risk of fire, only use
metal ductwork.
– The exhaust duct must not be bent
or compressed.
Please read and follow the
– Make sure all connections are
secure.
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk of
personal injury. Follow all local building
codes when installing the hood.
– Where the ductwork is horizontal, it
must slope away from the hood at
least 1/8" per foot (1 cm per meter) to
prevent condensation dripping into
the appliance.
– If the exhaust is ducted through an
outside wall, a Telescopic Wall Vent
can be used.
31
Air extraction
Condensate trap
optional accessory
– If the exhaust is ducted into an
inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Never connect an exhaust hood to
an active chimney, dryer vent, flue,
or room venting ductwork. Seek
professional advice before
connecting an exhaust hood vent to
an existing, inactive chimney or vent
flue.
In some cases, a condensate trap may
also be required to collect and
evaporate any condensate which may
occur. This optional accessory is
available for ducts 5" (125 mm) and 6"
(150 mm) in diameter.
Important
If the ductwork runs through rooms,
ceilings, garages, etc. where
temperature variations exist, it may
need to be insulated to reduce
condensation.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust outlet.
32
Technical data
Total connected load. . . . . . . . . . 450 W
fan motor . . . . . . . . . . . . . . . . . . 350 W
lighting. . . . . . . . . . . . . . . . . . 2 x 50 W
Power supply voltage . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Circuit rating. . . . . . . . . . . . . . . . . . 15 A
Weight
DA 398-5 . . . . . . . . . . 55.2 lbs (25.1 kg)
DA 399-5 . . . . . . . . . 57.4 lbs (26.1 kg)
33
34
35
Alteration rights reserved / 3410
M.-Nr. 07 759 400 / 00
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
|