INSTALLATION INSTRUCTIONS FOR PART 99-5719
INSTALLATION INSTRUCTIONS FOR PART 99-5719
APPLICATIONS
FORD TAURUS
2004 - 2007
99-5719
KIT FEATURES
• ISO & DIN Head Unit Provision w/ Pocket
• DDIN Head unit provisions
• Integrated auto climate controls and display
• Integrated passenger airbag light
• Painted Scratch Resistant Matte Black
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket
• E) DDIN Brackets • F) DDIN Trim Plate • G) In-Car Temp Sensor Housing • H) Harness Extension
B
E
C
D
A
H
G
F
TOOLS REQUIRED
• Radio Removal Tool (Metra Part #86-5618) • Phillips Screwdriver
• Panel Removal Tool • Socket Set • Cutting Tool or File • T10 Torx Screwdirver
METRA. THE WORLD’S BEST KITS.™
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932
metraonline.com
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
99-5719
99-5719 DASH DISASSEMBLY
NOTES
FORD TAURUS 2004- 2007
Disconnect the negative
battery terminal to prevent an
accidental short circuit.
1
A
Using Metra’s 86-5618, pull
the factory radio/climate
control panel from the dash.
(Fig. A)
2
Disconnect the audio system
3
B
connectors, blower motor
switch connector, vacuum
hose harness, a/c damper
door switch connector, and
potentiometer connector.
Remove the panel.
Remove (2) torx-head screws
securing the mounting clips to
the sides of the factory
radio/climate control panel
and remove the clips. (Fig. B)
4
5
Mount the clips to the
Integrated Mounting Kit with
the same torx-head screws.
1
99-5719 KIT PREPARATION
99-5719
FORD TAURUS 2004- 2007
FORD TAURUS 2004- 2007
AUDIO WIRING
Remove the In-Car temp
2
1
A
Fig. A
Back
wall
sensor housing from the
back of the factory control
panel. Insert into the includ-
ed In-Car temp sensor
housing and mount the
assembly under the dash.
Open the trunk, remove (4) pop-
clips from the driver’s side trunk
liner and remove the liner. (see
Fig. A) ocate the factory tuner on
the wall of the trunk and discon-
nect the speaker and antenna plugs
Inside edge
of sub-dash
Back
wall
Fig. B
Fig. A
Inside edge
of sub-dash
(located under
the rear deck)
Fig. B
(it is NOT necessary to remove
the tuner). (see Fig. B). Plug the
70-5715 into the unit speaker plug
and the antenna extension lead into
the unit antenna plug. Slide the ex-
tension harness through the space
in the back seat between the seat
back and seat bottom. Unclip the
rocker trim, tuck the extension har-
ness under the carpet and stretch
the harness to the back of the dash.
(Replace the rocker trim when
completed). Splice the speaker
leads on the extension harness into
the rear of the aftermarket head
unit. Plug the factory wiringhar-
nesses into the switch connectors
(previously mounted in step #2)
and audio connectors on the back
of the Integrated Mounting Kit.
Remove the factory rear sup-
port in the sub-dash. (Fig. A)
2
Continue to Kit Assembly
2
7
99-5719
99-5719
FORD TAURUS 2004- 2007
FORD TAURUS 2004- 2007
DDIN/STACKED ISO DIN
HEAD UNIT PROVISION
DIN HEAD UNIT PROVISION
1
Locate the factory wiring har-
ness in the dash. Metra
A
......... Continued from Pg.5
recommends using the prop-
er mating adapters (included)
from Metra and AXXESS to
integrate your new radio.
Re-connect the negative bat-
tery terminal and test the unit
for proper operation.
Snap the double DIN trim
plate into the radio housing.
(Fig. B)
B
5
Continue to “Audio Wiring”......
Slide the DIN cage into the
Radio Housing and secure
by bending the metal locking
tabs down. (Fig. A)
B
2
Snap the pocket into the
bottom opening of the radio
housing. (Fig. B)
3
Slide the aftermarket head
unit into the cage and se-
cure. (Fig. B)
4
Continue to “Audio Wiring”....
6
3
99-5719
99-5719
FORD TAURUS 2004- 2007
FORD TAURUS 2004- 2007
DDIN/STACKED ISO DIN
ISO DIN HEAD UNIT PROVISION
HEAD UNIT PROVISION
Locate the factory wiring har-
1
A
Locate the factory wiring har-
1
A
ness in the dash. Metra
recommends using the proper
mating adapters (included)
from Metra and AXXESS to
integrate your new radio. Re-
connect the negative battery
terminal and test the unit for
proper operation.
ness in the dash. Metra
recommends using the proper
mating adapters (included)
from Metra and AXXESS to
integrate your new radio. Re-
connect the negative battery
terminal and test the unit for
proper operation.
Mount the ISO Brackets to the
head unit with the screws sup-
plied with the unit. (Fig. A)
2
3
4
5
B
Cut and remove the center
bar from the radio housing.
(Fig.A)
2
Snap the pocket into the bot-
tom opening of the radio hous-
ing. (Fig. B)
Snap the Double DIN brack-
ets to the inside edge of the
Double DIN trim plate.
3
Slide the head unit into the ra-
dio opening until the side clips
engage. (Fig. B)
Slide the Double DIN head
unit or stacked ISO head units
into the bracket/radio housing
assembly and secure the Dou-
ble DIN head unit or stacked
ISO head units to the assem-
bly using the screws supplied
4
Snap the Trim plate into the
Radio Housing.
Continue to “Audio Wiring”....
Continued on Pg. 6
with the radio. (Fig. B)
4
5
|