breeze
stand fan
M o d e l :
3 5 8 3 0
5 0 W
PLEASE READ ALL INSTRUCTIONS BEFORE USE
MW_CO35830_BREEZE_PLASTIC_DESK_FAN_IM.indd 1
7/9/2009 12:40:18 PM
SAFETY ADVICE AND WARNINGS
4.Fit the rear grille and secure with the plastic sup-
port nut. Make sure that the handle faces upwards
and the plastic pins are aligned to the correspond-
ing holes on the rear grille for perfect coupling.
•Read this instruction leaflet carefully before
using the appliance, and keep it for future con-
sultation.
•Position the appliance on an even, stable surface,
away from the heat and possible water splashes.
•Ensure that the indicated voltage on the rating la-
bel matches the mains voltage before plugging in
the appliance.
5.Fit the fan propeller and secure with blade sup-
port nut. Ensure that the drive pin that goes through
the motor axle fits securely in the grove at the back
of the propeller.
•Do not use the appliance if the cord is damaged.
•Never touch the plug with wet hands.
•Unplug the appliance by pulling on the plug, not
on the cord.
6.Insert the front grille through the top of the rear
grille. Fit the rear grille clips onto the front grille.
Check that the grille safety screw holes are aligned
at the bottom of the grille. Secure and tighten the
grille safety screw.
•Unplug the appliance from the mains when not in
use and before cleaning.
•This appliance is for household use only, not in-
dustrial use.
INSTRUCTIONS FOR USE
•Connect the appliance to the mains.
•Select the airflow required using the buttons:
•Never leave the appliance unattended.
•This appliance is intended for use by adults. Do
not allow children or disabled persons to use it.
•Do not move or change the position of the appli-
ance whilst in operation.
0. Stop fan
1. Minimum air flow
2. Medium air flow
3. Maximum air flow
•Any inappropriate use or non-compliance with the
operating instructions renders the warranty and the
manufacturer's liability null and void.
•Never insert fingers, pencils or any other objects
through the grille while the fan is operating.
•Completely assemble the fan before switching it
on.
•To completely stop all the fan functions, turns the
timer control to the O position.
SWING AND TILT
•The fan head can swing from right to left, sweep-
ing air from a certain area. To do so, simply press
the swing control.
ASSEMBLY INSTRUCTIONS
•To set the fan head, pull the swing control and
turn the head to the required position.
1.Cross the two base legs together. Secure and
tighten the column base to the base legs using the
4 screws provided.
•To tilt the fan head, loosen the tilt control by
holding onto the grille and motor casing with both
hands and resetting it to the required position.
•The control N can be used to adjust the height.
2.Unscrew the height adjustment control anti-
clockwise to fit the small trim to the column base.
Once the trim is in place, refit the height adjustment
control and set the required height of the telescopic
tube.
CLEANING
•Unplug the appliance and allow it to cool before
cleaning.
3.Fit the body of the fan to the telescopic column,
adjusting the screw behind the body.
MW_CO35830_BREEZE_PLASTIC_DESK_FAN_IM.indd 3
7/9/2009 12:40:19 PM
•On removing the front grill to clean the propeller,
make sure that the fan is unplugged before remov-
ing the guard.
•Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
•Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
•Do not submerge the appliance in water or any
other liquid.
ANOMALIES AND REPAIR
In the event of a failure in the mains connection,
do not try to replace it, as this could be danger-
ous. Take the appliance to an authorised Technical
Assistance Service. The same applies to any other
type of anomaly.
MW_CO35830_BREEZE_PLASTIC_DESK_FAN_IM.indd 4
7/9/2009 12:40:19 PM
MW_CO35830_BREEZE_PLASTIC_DESK_FAN_IM.indd 5
7/9/2009 12:40:19 PM
MW_CO35830_BREEZE_PLASTIC_DESK_FAN_IM.indd 6
7/9/2009 12:40:19 PM
|