E X E C U T I V E
BRAVIS SIMO II PRO - STEAM STATION
complies with
INTERNATIONAL
Model:
2 3 8 1 0
IEC60355
2100W
SAFETY SPECIFICATIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 1
11/17/2009 12:49:20 PM
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 6
Fig. 5
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 3
11/17/2009 12:49:22 PM
Tips and safety warnings
- Do not use the appliance if it has been dropped,
if there are visible signs of damage or if it leaks.
-This appliance is not intended for use by
persons(including children)with reduced physi-
cal, sensory or mental capabilities, or lack of ex-
perience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
Before using the appliance for the first time
This professional iron works with tap water.
However, the use of distilled water is recomended
in areas with a high lime level in the water. Some
parts of the iron have been slightly greased.
They can therefore give off steam on first use, but
this steam will disappear after a short time.
-Children should be supervised to ensure that they
do not play with the appliance.
-Please read these instructions carefully before us-
ing the appliance and keep them for future refer-
ence.
Practical tips
-Unpack the appliance and check it is in perfect
condition and working order, as any factory fault
or damage caused by transport is covered by the
MELLERWARE guarantee.
-Keep the sole plate smooth, do not apply it to
metallic objects (i.e., to the ironing-board, butons,
zips...).
-Fit the iron in its housing (L) for transport and stor-
age, in order to improve its stability.
-To avoid burns, do not lean Bravissimo 2 Pro’s
iron on its back.
-This device has been designed for household
use, not for commercial use.
-Do not leave the appliance without supervision if
you are not going to use it immediately. This will
save energy and prolong the working life of the
appliance.
Steam ironing
-Keep the appliance out of the reach of children.
-The appliance must not be connected to the
mains while the boiler is being filled (Fig. 1).
-Before connecting the appliance to the mains, en-
sure the supply voltage is the same as that marked
on the appliance. The water filling inlet must not
be open during operation.
When you start to iron, proceed as follows:
-Unscrew the cap (F) and fill the boiler with water,
using a jug (Fig. 1) (if you fill it with hot water, the
appliance will be ready for use sooner).
-Even if the boiler has a certain level of water, it is
always recommended to fill it to the top for a longer
range, thanks to its large 1l capacity.
-This appliance must be connected to an electrical
socket with an earth connection.
-Carefully close the cap (F), screwing it to the end.
-Place the boiler on a flat , stable surface.
-Plug the appliance into the mains.
-Any improper use or failure to comply with the in-
structions for use will invalidate the warranty and
free the manufacturer from any liability
concerning the appliance.
-Switch on the boiler and the iron by pressing the
relevant switches (B) and (A). The corresponding
LEDs will light (Fig. 2).
-IF THE IRON IS IN ITS HOUSING AT MAXIMUM
TEMPERATURE FOR A LONG TIME, IT MAY DIS-
COLOUR, BUT THIS HAS NO EFFECT ON THE
PROPER OPERATION OF THE APPLIANCE.
- The appliance must be used and placed on a flat,
stable surface
- When placing the appliance on its support, make
sure the surface on which the support is fitted is
stable.
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 4
11/17/2009 12:49:22 PM
Important: For cotton and linen clothes, it is rec-
ommended to put the base of the iron in contact
with the fabric. For more delicate fabrics, it is rec-
ommended to keep the base of the iron at a dis-
tance of some centimetres.
Thermostat
control
Type of
fabric
Steam
position
No
No
•
Nylon / Silk
Wool
••
Yes
Cotton, Linen
Dry ironing
•••
-Connect the professional iron to the
mains.
It is recommended not to use steam in the • and
•• thermostat positions, as water could drip.
-Turn on the iron switch (A).
-Set the iron temperature with the thermostat con-
trol (J), depending on the fabric to be ironed.
-Set the desired temperature with the thermostat
control (J), depending on the type of cloth to be
ironed (Fig. 3).
After each ironing
-The appliance will be ready for use when the
pressure indicator LED (E) lights up (Fig. 4).
While ironing, this LED (E) goes on and off auto-
matically, this is normal.
-Switch off the professional iron by pressing
switches (B) and (A).
-Unplug the power cable (G) from the mains.
-Clean the base of the iron while it is still hot,
using a damp cloth, after each use.
-The rest of the appliance can also be cleaned us-
ing a damp cloth.
-By pressing the steam switch (H) you will get a
constant steam jet (Fig. 5). The steam stops when
you release the switch.
Never submerge the appliance in water or any
other liquid, or hold it under a running tap. Do
not use solvents or abrasive products to clean
it.
How to fill the boiler while ironing
To fill the boiler, proceed as follows:
-Eliminate steam pressure from inside the boiler
by switching on the steam switch (H) (Fig. 5).
-Turn off the boiler (B) and iron (A) switches.
-Unplug the appliance from the mains.
-Carefully unscrew the cap (F) to let the residual
steam out of the boiler.
Maintenance
With the boiler’s descaling system, limescale in-
crustations are reduced thanks to the exclusive
features of the stainless material used. To clean the
inside of the boiler, you simply have to proceed as
follows every three months:
-Wait for some minutes and carefully pour 1l of
water into the boiler using a jug (Fig. 1).
-Carefully close the cap (F) again, screwing it to
the end.
Fill the boiler with tap water, shake and empty. Re-
peat these steps two or three times consecutively.
Vertical ironing
To descale:
-Unplug. Empty the content of a bag into the boiler.
Fill with water and select the steam position.
-Plug in. Switch the professional iron on.
-Place the iron in the ironing position. Activate the
steam, shake the iron softly.
It is possible to iron hanging curtains, garments
on their own hangers... (Fig.6)
-Adjust the iron thermostat control (J) to the maxi-
mum temperature.
-Iron from top to bottom and press the iron steam
switch (H).
-Let the product work for 10 minutes.
-Rinse thoroughly with water & empty completely.
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 5
11/17/2009 12:49:22 PM
Breakdowns and repairs
Breakdowns and repairs
In the event of any breakdown, check the follow-
ing chart.
In the event of any breakdown, check the follow-
ing chart.
- In the event of malfunctions, take the appliance to
an authorized Technical Support Service.
- Do not try to dismantle or repair it yourself as this
may be dangerous.
- In the event of malfunctions, take the appliance to
an authorized Technical Support Service.
- Do not try to dismantle or repair it yourself as this
may be dangerous.
- If the mains connection is to be replaced, pro-
ceed as in the event of a malfunction.
- If the mains connection is to be replaced, pro-
ceed as in the event of a malfunction.
After each ironing
-Switch off the professional iron by pressing
switches (B) and (A).
-Unplug the power cable (G) from the mains.
-Clean the base of the iron while it is still hot,
using a damp cloth, after each use.
-The rest of the appliance can also be cleaned us-
ing a damp cloth.
Never submerge the appliance in water or any
other liquid, or hold it under a running tap. Do
not use solvents or abrasive products to clean
it.
Maintenance
With the boiler’s descaling system, limescale in-
crustations are reduced thanks to the exclusive
features of the stainless material used. To clean the
inside of the boiler, you simply have to proceed as
follows every three months:
Fill the boiler with tap water, shake and empty. Re-
peat these steps two or three times consecutively.
To descale:
-Unplug. Empty the content of a bag into the boiler.
Fill with water and select the steam position.
-Plug in. Switch the professional iron on.
-Place the iron in the ironing position. Activate the
steam, shake the iron softly.
-Let the product work for 10 minutes.
-Rinse thoroughly with water & empty completely.
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 6
11/17/2009 12:49:22 PM
Causes
Breakdowns
Solutions
Iron thermos-
tat control (J)
set to the mi-
nimum posi-
tion "·""··".
Set the thermostat
control to the
Water drips
from the
steam zone "···".
holes on the
base of the
iron when
turning on
the steam
switch (H).
The boiler is
too full.
Remove some
water.
The boiler
Place it on a
is in a tilted horizontal sur-
position.
face.
The iron does The switch Switch it to
not heat and
the LED (K)
does not light
up.
“on” (A).
Iron ther-
Adjust the ther-
mostat control.
mostat con-
trol (J) set to
the minimum
position.
Faulty power Check the power
connection. points.
No steam co- Empty boiler. Fill the boiler
mes out
when pres-
sing the
steam switch
(H).
with water.
Switches (B) Switch them
and (A) are on.
Leak Cap (F) not Let the boiler cool
from the
properly clo- and screw the cap
sed.
(F) to the end
again.
cap (F).
Safety valve Go to an authori-
activated.
zed Technical
Service.
The boiler cap There is
(F) does not steam re-
Press the steam
switch (H) to let
unscrew easi- maining in- the steam out.
ly.
side the
boiler.
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 7
11/17/2009 12:49:22 PM
27 Nourse
Avenue Epping
2
Cape Town
P.O. Box 975 Eppindust 7475 South Africa
Tel: +27 21 534 8114 Fax: +27 21 534 8086
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 8
11/17/2009 12:49:22 PM
|