PRODUCT DESCRIPTION
FEATURES
BBU
BATTERY
BACKUP
UNIT
The Model BBU Battery Backup Unit is designed to provide DC power for Linear’s
Model LDCO800 Garage Door Operator during AC power outages.
INTERNAL SOUNDER
3 BEEPS EVERY MINUTE = FAILED BATTERY TEST
The BBU contains two rechargeable batteries that are maintained and charged by
the LDCO800 operator. If the installation’s AC line power is interrupted, the BBU will
power the operator for up to 24 hours. The duration of the operator’s battery backup
will depend on the number of times the garage door is cycled without AC power. The
batteries will be fully recharged within 48 hours after AC power is restored.
MOUNTING TABS (3)
The BBU contains an internal sounder to indicate the current status of the battery
unit.The unit regularly performs a self-check routine while AC power is present. If the
batteries test low or dead, the unit will sound three beeps every minute to indicate
that service is required.
MOUNTING SCREWS (3)
WIRING HARNESS
Installation Instructions
For Use with Model LDCO800
Garage Door Operators
Every LDCO800 is compatible with the BBU.The operator now has three pre-drilled
holes in the chassis to mount the BBU and a connector for the BBU on the controller
board.
For retrofit installations, replace the LDCO800 operator’s controller board with a newer
Model HAE00061 controller board that has the BBU connector. Refer to the mounting
template supplied to drill three holes in the chassis of the operator to mount the BBU.
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
REMOVE OPERATOR COVER
INSTALL BATTERY BACKUP UNIT IN OPERATOR
CONNECT POWER WIRES
USE THE THREE SCREWS TO ATTACH
THE BATTERY BACKUP UNIT TO
THE OPERATOR BASE PLATE
REMOVE JUMPER PLUG FROM
CONTROLLER BOARD'S 3-WIRE HARNESS
(SAVE THE JUMPER PLUG)
1
UNPLUG THE OPERATOR BEFORE PROCEEDING !!!
FOR RETROFIT INSTALLATIONS,
REFER TO MOUNTING TEMPLATE
CONNECT THE 3-WIRE HARNESS TO
THE BATTERY BACKUP 3-WIRE HARNESS
2
LOOSEN THE
FOUR COVER
SCREWS
JUMPER PLUG
NOTE: THE JUMPER PLUG MUST
REMAIN IN PLACE UNTIL THE
BATTERY BACKUP
3
UNIT IS INSTALLED
REMOVE THE
OPERATOR'S
COVER
THE BATTERY BACKUP
UNIT CAN BE INSTALLED
WHILE THE OPERATOR IS
MOUNTED OR WHILE THE
OPERATOR IS ON THE FLOOR
REPLACE OPERATOR COVER
TEST OPERATOR
LINEAR LIMITED WARRANTY
This Linear product is warranted to the original consumer against defects in material and workmanship for 1 year. Linear will repair,
or at its option, replace, any device that it finds requires service under this warranty, and will return the repaired or replaced device
to the consumer at Linear’s cost. Devices must be sent to Linear for service at owner’s expense. This warranty does not apply to
damage to the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear or due to failure to follow
Seller’s instructions, or arising from improper installation, storage or maintenance. In no event will Linear be responsible for incidental,
compensatory, punitive, consequential, indirect, special or other damages. The remedies provided by this warranty are exclusive.
Some states do not allow the exclusion or limitation of incidental and consequential damages, so the above limitation or exclusion may
not apply to you. Any warranties implied by law are limited to the time periods set forth above. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you.This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
1
BE SURE TO LET THE BATTERY
BACKUP UNIT CHARGE FOR
48 HOURS BEFORE TESTING
1
2
REPLACE THE
OPERATOR'S
COVER
TIGHTEN THE FOUR
COVER SCREWS
For warranty service and shipping instructions contact Linear at the phone number shown below. In order to be protected by this
warranty, save your proof of purchase and send a copy with equipment should repair be required. All products returned for warranty
service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
2
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply
with the limits for a Class B computing device in accordance with Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
UNPLUG THE
OPERATOR
3
4
TEST RUN THE OPERATOR
(THE OPERATOR'S LAMP WILL NOT LIGHT)
•
•
•
•
Relocate the Console away from the TV/radio receiver.
Plug the Console into a different wall outlet so that the Console is on a different branch circuit.
Re-orient the TV/radio antenna.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.
PLUG THE OPERATOR BACK IN
Copyright © 2012 Linear Corporation
232338 B
|