Features
Installation Steps
Lockset Parts List
Simple to Install -The DoorGard 212LS Lockset installs in 15 minutes
and programs the same as all DoorGard/IEI keypads. It includes
all mounting hardware, and easily retrofits into any standard cylindrical
door prep (ANSI/BHMA A 156.2-2003). The 212LS has a replaceable
core, for the manual key override. The sleek design fits with any décor
and is available in 26D Stainless and US3 Polished Brass, right or left
handed crescent door handles.
Door & Frame Prep
1. Spanner wrench
2. T-Strike Door Latch
2-3/8” Backset
3. T-Strike Door Latch
2-3/4” Backset
4. Strike Plate
5. Strike Plate Cover
6. Latch/Strikeplate Screws
7. Allen Wrench
8. Exterior Door Handle/
keypad
11. Interior Faceplate/Door
Handle w/battery case
12. Interior Faceplate
13. Override Keys (2)
14. Pin Wrench (pries open key
slot cover)
• Remove existing Lock from door
• If it is new door with no holes, use template provided
• Measure backset.
Installation
1. Unpack the lockset and inventory all parts. Remove mount-
ing screws, separate lock assembly, and both interior/exterior
handle plates and the two rubber gaskets.
15. Key Slot Cover
Right Hand
16. Screws: 2 sets Lock
Assembly screws (thick,
thin doors)
17. Sealing Washer
18. Faceplate Assembly Nut
212LS – C26DCR-Rt - F/G:DoorGard Grade 2 Lockset/Cylindrical,
Stainless, Crescent handle, Right handed.
212LS – CUS3CR-Rt - F/G: DoorGard Grade 2 Lockset/Cylindrical,
Stainless, Crescent handle, Right handed.
2. Insert the strike plate hole cover (#5) and attach strike plate
(#4) in the door jam/frame, securing with two Phillips head
screws.
9. Exterior Gasket
10. Interior Gasket
Left Hand
3. Install T-Strike Door Latch (#2 or #3) into doorjam/frame and
secure with two Phillips head screws.
212LS – C26DCR-Lt - F/G: DoorGard Grade 2 Lockset Cylindrical,
Stainless, Crescent handle, Left handed.
212LS – CUS3CR-Lt - F/G: DoorGard Grade 2 Lockset Cylindrical,
Stainless, Crescent handle, Left handed.
4. Assemble locks inserting two Rubber Gaskets (#8, 9, 10, 11).
5. Thread battery wires through hole in Interior Faceplate/Door
Handle (#11).
4
Easy to Maintain -Change the battery in three minutes. The 212LS
Lockset uses four (4) 1.5V AA batteries for up to 15,000 uses or up to
five years. An alarm activates Low Battery Alert allowing for 30 more
uses.
User Codes - The 212LS lock recognizes up to 120 users with a
different code for each, and the lockset retains codes without batteries.
Codes can be one to six digits in length and digits can be repeated.
The Master Code is always stored in user location one (1). A reset
button is provided inside the lock which restores factory defaults and
removes codes already stored. The lockset is equipped with an override
mechanical key. The code toggles to allow passage for an event so any
key will open the lock.
Security and Protection -The 212LS Lockset is designed with a
safeguard against forced entry since the outside lever is not
mechanically connected to the latch until the lock activates. Also, after
three invalid code attempts, there is a 20 second lockout period for the
keypad.
6
2
3
1
6. Attach Interior Faceplate/Door Handle (#11) to Exterior Door
Handle (#8), securing with two short or long assembly screws.
(#16)
5
7
8
7. Insert batteries and connect battery clip.
12
8. Secure Interior Faceplate (#12) with clear plastic washer with
Nut (#17, 18)
10
9. Use spanner wrench (#1) to tighten nut (#15).
10. Program the system as described in this manual.
11. Instruct the users on lockset operation.
9
11
13
Manual Operation
14
• Use Pin Wrench (#14) to pull off cover (#15).
15
18
16
17
• Use override key (#13).
• Turn left twice.
Rugged Design -The 212LS is designed for both commercial and
industrial use.
Figure 1. Parts Diagram
P1345
|