Lincoln Electric Welding Consumables NR 131 User Manual

US-CW110  
3/1/2008  
Date:  
MSDS No.:  
Innershield NR-131  
All  
Trade Name:  
Sizes:  
2/1/2000  
Supersedes:  
M A T E R I A L S A F E T Y D A T A S H E E T  
For Welding Consumables and Related Products  
Conforms to Hazard Communication Standard 29CFR 1910.1200 Rev. October 1988  
SECTION I - IDENTIFICATION  
Manufacturer/  
Supplier:  
Product Type: Flux Cored Electrode  
The Lincoln Electric Company  
22801 St. Clair Avenue  
Cleveland, OH 44117-1199  
(216) 481-8100  
Classification: AWS E70T-10  
SECTION II - HAZARDOUS MATERIAL (1)  
I M P O R T A N T !  
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal  
use of this product are covered by Section V; see it for industrial hygiene information.  
CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.  
(1) The term “hazardous” in “Hazardous Materials” should be interpreted as a term required and defined in the Hazards Communication  
Standard and does not necessarily imply the existence of any hazard. All materials are listed on the TSCA inventory.  
TLV  
PEL  
Ingredients:  
CAS No.  
7439-89-6  
7429-90-5  
7789-75-5  
7439-95-4  
1317-65-3  
68476-89-1  
1309-48-4  
7440-21-3  
65996-74-9  
7439-96-5  
1333-86-4  
Wt.%  
< 5  
< 5  
< 5  
1
mg/m3  
10*  
10  
mg/m3  
10*  
15  
Iron  
Aluminum and/or aluminum alloys (as Al)*****  
Fluorides (as F)  
Magnesium and/or magnesium alloys and compounds (as Mg)  
Limestone and/or calcium carbonate  
Rare Earths  
Magnesite  
Silicon and/or silicon alloys and compounds (as Si)  
Iron oxides  
Manganese and/or manganese alloys and compounds (as Mn)*****  
Carbon black  
2.5  
2.5  
10*  
10  
10*  
15  
1
0.5  
10*  
10  
10*  
15  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
10*  
5
10*  
10  
0.2  
3.5  
5 (c)  
3.5  
Carbon steel tube  
7439-89-6  
85  
10*  
10*  
Supplemental Information:  
(*)  
Not listed. Nuisance value maximum is 10 milligrams per cubic  
meter. PEL value for iron oxide is 10 milligrams per cubic meter.  
TLV value for iron oxide is 5 milligrams per cubic meter.  
(c)  
Value is for manganese fume. Present PEL is 5  
milligrams per cubic meter (ceiling value). Values  
proposed by OSHA in 1989 were 1.0 milligrams per  
cubic meter TWA and 3.0 milligrams per cubic meter  
STEL (Short Term Exposure Limit).  
(*****) Subject to the reporting requirements of Sections 311, 312, and 313 of  
the Emergency Planning and Community Right-to-Know Act of 1986  
and of 40CFR 370 and 372.  
SECTION III - HAZARD DATA  
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section VI.  
Product is inert, no special handling or spill procedures required. Not regulated by DOT.  
Rev 9/07  
(CONTINUED ON SIDE TWO)  
 

Learning Resources Games Goodie Game User Manual
LG Electronics Clothes Dryer DLE2701V User Manual
LG Electronics Microwave Oven MS3447GR User Manual
Life Fitness Elliptical Trainer 93X 0XXX 04 User Manual
Makita Cordless Drill DF010DSE User Manual
Makita Cordless Saw BJV180 User Manual
Makita Drill 6407 User Manual
McIntosh Stereo Amplifier MC402 User Manual
Metra Electronics Automobile Accessories 99 7861 User Manual
MicroNet Technology Network Router SP5001 S User Manual