Satellite Speaker
Cat. No.
AESS5
USER GUIDE
DI-000-AESS5-02A-X0
SPEAKER PLACEMENT
NOTE: The satellite speakers can be placed directly on a shelf, or
mounted on a wall using the included wall brackets.
Left and Right Front Channels
For left and right front channels, place one satellite to the left and another
to the right of the television, as shown in Figures 1A and 1B. Since the
speakers are magnetically shielded, you can place them very close to the
TV without worrying about the magnetic field distorting the picture.
Center Channel
For the center channel, place the speaker directly on top of, or below,
your television. Use the included brackets for wall mounting.
Surround Channels
For left and right surround channels, place one speaker on the left and
another on the right, to the side of or slightly behind the listening area.
The surround speakers should be mounted at a height of between 4 feet
and 7 feet.
Figure 1B
Alternate Placement
Figure 1A
Typical Placement
Subwoofer
Right
Subwoofer
Front
Channel
Left
Front
Right
Front
Center
Channel
Channel
Channel
Center
Right
Surround
Channel
Channel
Left
Front
Channel
Listening Postion
Left
Right
Left
Surround
Surround
Channel
Surround
Channel
Channel
Figure 1B shows an alternative
layout, which may be more suitable
for some rooms.
Figure 1A shows a typical
installation, satellite speakers
are used to reproduce sound for
the front and surround channels.
The center channel reproduces
sound and dialogue.The powered
subwoofer provides bass for
effects and music.
3
SPEAKER CONNECTIONS
TURN OFF ALL POWER.
Speakers and electronics terminals have corresponding (+) and (–)
terminals. It is important to connect both speakers identically: (+) on
the speaker to (+) on the amplifier and (–) on the speaker to (–) on the
amplifier. Wiring “out of phase” results in thin sound, weak bass and a
poor stereo image. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +). Also, consult the ownerʼs
manuals that were included with your amplifier or receiver to confirm
connection procedures.
With the advent of multichannel surround sound systems, connecting all
of the speakers in your system with the correct polarity remains equally
important in order to preserve the proper ambience and directionality of
the program material.
Black = –
Red = –
Insert Bare
End; Release
Tab
Press Tab
and Hold
No
Stripe = +
Stripe = –
Speaker Wire
Receiver or Amplifier
(rear view)
Black = –
red = +
+
–
Output
One Channel Shown
WIRE LENGTH
Up to 20 ft.
Up to 30 ft.
RECOMMENDED SIZE
16 gauge
14 gauge
Greater than 30 ft.
12 gauge
4
INSTALLATION
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE
WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
NOTE: LEVITON ARCHITECTURAL EDITION™ POWERED BY
JBL SATELLITE SPEAKERS WERE DESIGNED TO BE EASILY
INSTALLED. HOWEVER, IF YOU ARE UNSURE OF YOUR ABILITY TO
PROPERLY INSTALL THESE LOUDSPEAKERS, PLEASE CONTACT
YOUR DEALER OR A QUALIFIED INSTALLER.
NOTE: SPEAKER WIRE RUNS SITUATED INSIDE A WALL NEED
TO BE FIRE-RATED. WHEN IN DOUBT, CONSULT YOUR LOCAL
ELECTRICAL INSPECTOR FOR CORRECT WIRE RATINGS.
WALL MOUNTING
The Cat. No. AESS5 satellite speaker is to be wall-mounted with the
adjustable wall-mounting brackets included, or placed on a shelf.
This product is not intended for ceiling mounting. Note that is the
responsibility of the end user for proper selection and use of mounting
hardware, available through hardware stores, to properly and safely wall-
mount the speakers. Optional, adjustable, wall-mounting brackets are
available from JBL.
Contact your dealer, or call 800-336-4JBL for a dealer near you, and
order model no. WBN26WHT.
Vertical Mounting
Horizontal Mounting
Bracket Assembly:
CAUTION: PROPER SELECTION OF MOUNTING HARDWARE NOT
INCLUDED HEREIN AND PROPER ASSEMBLY AND INSTALLATION
OF BRACKETS, INCLUDING BUT NOT LIMITED TO SELECTION
OF APPROPRIATE WEIGHT BEARING SUPPORT AND BRACKET
USE WITH THE SPECIFIED SPEAKER ONLY IS THE EXCLUSIVE
RESPONSIBILITY OF THE CUSTOMER. MANUFACTURER
DISCLAIMS ANY LIABILITY FOR THE SELECTION OF MOUNTING
HARDWARE AND OR BRACKET INSTALLATION.
1. Loosen and remove the molded nut (2) by turning it counter clock-
wise. Use the supplied metal bar (5) if necessary by inserting it in one
of the holes on the molded nut (2).
5
2. Pull the ball/shaft (3) out of the wall bracket (4).
3. Slide on the molded nut (2) onto the ball/shaft (3) with threaded
opening facing the ball, and thread on the metal nut (1) all the way
onto the ball/shaft (3), with the nut (1)ʼs “knurled” surface facing away
from the ball.
4. Screw on the ball/shaft (3) into the threaded insert on the back of the
speaker cabinet until it is fully seated against the bottom of the insert.
5. Tighten the “knurled” nut (1) using a crescent wrench until it is firmly
seated against the back of the speaker and has fully locked the
ball/shaft (3) and the speaker cabinet together. Please note that once
this nut is tightened, it may embed some marks on the back of the
speaker where the attachment is made. However, these marks will be
covered by the nut (1).
6. Mount the wall bracket (4) onto a wood stud on the wall, using #10,
minimum 1 inch long, wood screws (6, not included). If necessary,
use a stud finder to locate the studs behind the drywall. Make sure
that all 4 screws are driven into the stud and not in drywall. If the
bracket needs to be mounted on drywall, the use of properly selected
and installed wall-anchors and screws is essential.
7. Holding the speaker cabinet with both hands, reinsert the ball portion
of the ball/shaft (3) into the wall bracket (4).
8. Hand tighten the molded nut (2) while positioning the speaker for the
intended orientation.
9. Once the orientation of the speaker is finalized, use the metal bar (5)
in one of the holes on the molded nut (2) and tighten securely.
4
3
2
1
®
6
5
1 – Metal Nut (2)
2 – Molded Nut (2)
3 – Ball/Shaft (2)
4 – Wall Bracket (2)
5 – Metal bar (1)
6 – Wood Screw (not included)
6
OPERATION
Surround Modes:
When using the system in a Dolby* Digital or DTS® home theater system,
ensure that all Cat. No. AESS5 speakers are set to “Small”.
When using the Cat. No. AESS5 in a Dolby Pro Logic* home theater
system, ensure that the receiver's center channel mode is set to
“Normal”.
Some Dolby Digital-equipped receivers/processors offer different setup
options for each source or surround mode, e.g., Cd-Stereo, Videotape,
Dolby, Pro Logic. In each case, follow your equipment's instructions to
ensure that the subwoofer output is turned ON and the speakers are set
to “Small” in each mode.
MAINTENANCE AND SERVICE
The satellite enclosure may be cleaned using a soft cloth to remove
fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or remade
periodically. The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions, and other factors,
but once per year is the minimum.
If a problem occurs, make sure that all connections are properly made
and clean. If a problem exists in one loudspeaker, reverse the connection
wires to the left and right system. If the problem remains in the same
speaker, then the fault is with the loudspeaker. If the problem appears in
the opposite speaker, the cause is in another component or cable.
Refer to the Troubleshooting section for additional information.
7
TROUBLESHOOTING
IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
• Check that receiver/amplifier is on and a source is playing.
• Check all wires and connections between receiver/amplifier and
speakers. Make sure all wires are connected. Make sure none of the
speaker wires are frayed, cut, punctured or touching each other.
• Review proper operation of your receiver/amplifier.
IF THERE IS NO SOUND COMING FROM ONE SPEAKER:
• Check the “Balance” control on your receiver/amplifier.
• Check all wires and connections between receiver/amplifier and
speakers. Make sure all wires are connected. Make sure none of the
speaker wires are frayed, cut, punctured or touching each other.
IF THERE IS LOW (OR NO) BASS OUTPUT:
• Make sure the connections to the left and right “Speaker Inputs” have
the correct polarity (+ and –).
• Consider adding a powered subwoofer to your system.
• In Dolby Digital or DTS modes, make sure your receiver/processor
is correctly configured. When using a subwoofer, make sure the
subwoofer output of the receiver/ processor has been enabled. If
no subwoofer is being used, make sure the left and right front and
rear speakers have been configured as “LARGE.” See your receiver/
processorʼs ownerʼs manual for further information on correct speaker
configuration in Dolby Digital, DTS and other surround sound modes.
IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS
VOLUME IS INCREASED:
• Check all wires and connections between receiver/amplifier and
speakers. Make sure all wires are connected. Make sure none of the
speaker wires are frayed, cut , punctured or touching each other.
• If more than one pair of main speakers is being used, check the
minimum-impedance requirements of your receiver/amplifier.
8
NOTES
NOTES
NOTES
SPECIFICATIONS
NOTES:
• All features and specifications are subject to change without notice.
• † The maximum recommended amplifier power rating will ensure
proper system headroom to allow for occasional peaks. We do not
recommend sustained operation at these maximum power levels.
• * Trademark of Dolby Laboratories.
DTS is a registered trademark of Digital Theater Systems, Inc.
AESS5
Frequency Response
150Hz– 20kHz (+3dB)
High-Frequency Transducer
1/2" magnetically shielded
Recommended Amplifier
Power Range
10-100 watts
Dimension (H x W x D)
5" x 3-1/2" x 6-1/4"
(241mm x 159mm x 121mm)
Impedance
8 ohms nominal
Weight per Speaker
4.5 lbs (2.1kgs)
Crossover Frequency
86dB
Crossover Frequency
7,000Hz – 24dB/octave
Midrange Driver(s)
2-1/2" magnetically shielded
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of
its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the
purchase date. Levitonʼs only obligation is to correct such defects by repair or replacement, at its option, if within such
five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton
Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York
11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation.
This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels
or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a
particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied
warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable
for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of
use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies
provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
For additional information, contact Levitonʼs Techline at
406-000-05430-E
DI-000-AESS5-02A-X0
This page is NOT to be printed in the booklet
11.0"
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
8.5"
DI-000-AESS5-02A-X0
Black
Helvetica
OVERALL SIZE
50 lb. offset
Paper size:
11" x 8.5" (Printer Spread) 12 Pages
5.5"
Overall size:
5.5" x 8.5" (booklet - saddle stitch)
Final fold size:
DOCUMENTATION
N/A
KKC
11/30/05
8.5"
Booklet
Cat. No.
FINAL SIZE
|